EN
Patton electronic logo
Official user manual

Patton electronic MODEL 1012AR

5 pages·34 KB·Network Card·PDF·ENDEFRITNLJA
Patton electronic MODEL 1012AR
Table of Contents 25 sections MODEL 1012AR Asynchronous, Carrier Controlled Short Range Modem · USER MANUA L · 1.2 SERVICE · 1.1 RADIO AND TV INTERFERENCE · … ShowHide
Page 1 of the Patton electronic MODEL 1012AR user manual — MODEL 1012AR Asynchronous, Carrier Controlled Short Range Modem
Page 1 · click to enlarge
Page 1

Part# 07M1012AR-A Doc# 040051UA Revised 11/22/94

MODEL 1012AR Asynchronous, Carrier Controlled Short Range Modem

USER MANUA L

Patton electronic MODEL 1012AR — MODEL 1012AR Asynchronous, Carrier Controlled Short Range Modem diagram (page 1)
Fig. 1 · MODEL 1012AR Asynchronous, Carrier Controlled Short…

SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com

Page 2 of the Patton electronic MODEL 1012AR user manual — 2.0 GENERAL INFORMATION
Page 2 · click to enlarge
Page 2

All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container. This number may be obtained from Patton Electronics Technical Service at (301) 975-1007. Packages received without an RMA number will not be accepted. Patton Electronics' technical staff is also available to answer any questions that might arise concerning the installation or use of your Model 1012AR. Technical Service hours: 8AM to 5PM EST, Monday through Friday.

1.2 SERVICE

The Model 1012AR generates and uses radio frequency energy, and if not installed and used properly—that is, in strict accordance with the manufacturer's instructions—may cause interference to radio and television reception. The Model 1012AR has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. However, there is no guarantee that interfer- ence will not occur in a particular installation. If the Model 1012AR does cause interference to radio or television reception, which can be determined by disconnecting the RS-232 interface, the user is encour- aged to try to correct the interference by one or more of the following measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna and/or plugging the receiving equip- ment into a different AC outlet (such that the computing equipment and receiver are on different branches).

1.1 RADIO AND TV INTERFERENCE

Patton Electronics warrants all Model 1012AR components to be free from defects, and will—at our option—repair or replace the prod- uct should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modifi- cation. If this product fails or does not perform as warranted, your sole recourse shall be repair or replacement as described above. Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequen- tial damages arising from the use of or inability to use this product. Patton Electronics specifically disclaims all other warranties, expressed or implied, and the installation or use of this product shall be deemed an acceptance of these terms by the user.

1.0 WARRANTY INFORMATION

The 1012AR uses the latest in bi-directional, clamping, transient suppressors to protect itself and connected equipment against harmful transient surges. These suppressors can dissipate 600W per wire at 1.0 mS. Response times are typically 1.0 pS from 0 to the nominal breakdown level of 6.8 volts.

Built-in transformers eliminate much of the noise which can occur in commercial buildings. These transformers also eliminate ground loops caused by differences in reference ground. Consequently, the Model 1012AR may be used to extend RS-232 (TIA-561) distances in environments where connected equipment is located in different build- ings.

The Patton Model 1012AR asynchronous short range modem was designed for point-to-point or multidrop applications requiring hardware handshaking. In a multipoint environment, the master transmits data simultaneously to up to 10 addressable terminals. The terminals con- tend for the main channel by activating RTS (pin 4). Automatic equal- ization and gain control ensure the accuracy of transmitted data.

2.2 DESCRIPTION

2.1 FEATURES

Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warrant- ed for One Year parts and labor. If any questions or problems arise during installation or use of this product, please do not hesitate to con- tact Patton Electronics Technical Support at (301) 975-1007.

  • Line connection via RJ-11 or 8-pin RJ-45 jack
  • TIA-561 connection via 10-pin RJ-45 jack
  • Silicon Avalanche Diode surge protection - Standard
  • Supports data rates to 38,400 bps, distances to 6 miles
  • No AC power required. Draws required low power from TIA-561 interface
  • Transformer isolation
  • Automatic equalization and gain control
  • Full or half duplex, point-to-point or multipoint
  • Supports hardware handshaking
  • Allows up to 10 terminals to use a single port

2.0 GENERAL INFORMATION

Page 3 of the Patton electronic MODEL 1012AR user manual — 4.0 INSTALLATION
Page 3 · click to enlarge
Page 3
3. Closing the Case. To close the Model 1012AR’s case, be sure the end inserts are in place around th modular jacks (“side”side closest to the clip) and slide th case halves down around them. Then snap the case halves shut.
2. Setting the RTS Strap. On Figure 1 (below), you will see the location of the RTS strap on the PC board. To re-configure the Model 1012AR for transmitter constantly on, remove the strap by pulling it out with a pair of needle-nose pliers or tweezers. Be sure not to lose the strap.
1. Opening the Case. To open the Model 1012AR’s case, insert the blade of a small flat-head screw driver into the narrow slots on either side of the case and twist. The two case halves should pop apart. Then slide the case halves off of the two end inserts. This will expose the PC board.

The only user-modifiable setting on the Model 1012AR is the RTS control strap. The RTS control strap setting determines how its trans- mitter (i.e. carrier) is activated. When the RST control strap is ON (installed on the pins), the transmitter is enabled by activating RTS (RJ-45 pin 8). This is the factory setting.. When its strap is OFF (removed from the pins), the 1012AR’s transmitter is constantly on. If your application requires the transmitter to be constantly on (i.e. hard- ware flow control disabled), follow the instructions below:

The Model 1012AR is pre-configured at the factory to work in mul- tipoint applications, and in point-to-point applications that use hardware flow control. These are the vast majority of applications that call for the Model 1012AR. Therefore, you will normally have no need to re- configure the Model 1012AR: it will be strictly “plug-and-play”.

Figure 1. Model 1012AR board, showing the RTS strap location

3.0 CONFIGURATION

Figure 3. Pin connections for an EIA/TIA-561(RJ-45) to RS-232 (DB-25) patch cable. 3 4

If you wish to use the Model 1012AR with a DTE device that is equipped with a DB-25 RS-232 port, you will need to construct a patch cable according to the diagram shown in Figure 3 (below).

The Model 1012AR features a convenient, 10 pin RJ-45 jack for interface with your DTE device. This jack is wired as a DCE accord- ing to the EIA/TIA-561 specification. Figure 2 (below) shows the pins and signals for the modular EIA/TIA-561 interface. Note: Signal are named from the perspective of the DTE (PC/terminal). Therefore, even though pin 7 (below) is called “TD” , the signal is actually incom- ing to the DCE (Model 1012AR).

4.1 CONNECTION TO THE EIA/TIA-561 INTERFACE

The Model 1012AR features modular connectors on both the EIA/TIA-561 and 4-wire (line) sides. The EIA/TIA-561 interface is always a 10 pin RJ-45 jack (although its physical size is identical to an 8-pin RJ-45 jack). A one foot RJ-45 patch cable, wired straight through, is supplied with the unit. The 4-wire interface may be a 6 pin RJ-11 jack or an 8 pin RJ-45 jack.

1 N/C 2 RI Not Supported 3 CD From 1012AR 4 DTR To 1012AR 5 SG No Direction 6 RD From 1012AR 7 TD To 1012AR 8 CTS From 1012AR 9 RTS To 1012AR 10 N/C . Figure 2. Pin-outs for the Model 1012AR’s modular EIA/TIA-561 interface jack

SIGNAL 10 Pin RJ-45 (DCE) DB-25 (DTE) SIGNAL

10 Pin RJ-45 (DCE) SIGNAL DIRECTION

CD 3 8 CD DTR 4 20 DTR SG 5 7 SG RD 6 3 RD TD 7 2 TD CTS 8 5 CTS RTS 9 9 RTS

4.0 INSTALLATION

Isolation Transformers · Surge Suppressors · RTS/CTS Strap

Page 4 of the Patton electronic MODEL 1012AR user manual — RCVXMTXMT-
Page 4 · click to enlarge
Page 4

‡Standard color codes—yours may be different

†Connection to ground is optional

When installing two Model 1012AR units in a point-to-point appli- cation, the cable between them should be a crossover cable, as shown in the following chart. The color/pin number correlations below corre- spond to AT&T’s wiring standard for RJ-11 connectors.

4.2.1 POINT-TO-POINT CONNECTION

†Connection to ground is optional

The Model 1012AR offers RJ-11 and RJ-45 options for connection of the 4-wire data line. The signals/pins used are shown below:

4.2 CONNECTION TO THE 4-WIRE INTERFACE

GND† 1 Blue‡ White 6 GND RCV- 2 Yellow Red 4 XMT- XMT+ 3 Green Black 5 RCV+ XMT- 4 Red Yellow 2 RCV- RCV+ 5 Black Green 3 XMT+ GND 6 White Blue 1 GND

SIGNAL PIN# COLOR COLOR PIN# SIGNAL

RJ-11 SIGNAL RJ-45 SIGNAL

1 GND† 1 N/C 2 RCV- 2 GND 3 XMT+ 3 RCV- 4 XMT- 4 XMT+ 5 RCV+ 5 XMT- 6 GND 6 RCV+ 7 GND 8 N/C

1. Blue 2 - Yellow 3 - Green 4 - Red 5 - Black 6 - White
1. Blue 2 - Orange 3 - Black 4 - Red 5 - Green 6 - Yellow 7 - Brown 8 - Slate

Figure 5 (below) shows how to wire the two-pair cables properly for a Model 1012AR daisy-chain topology. Note that the ground con- nection is not needed.

4.3.2 DAISY CHAIN TOPOLOGY

Figure 4 (below) shows how to wire the two-pair cables properly for a Model 1012AR star topology. Note that the ground connection is not needed

4.3.1 STAR TOPOLOGY

The Model 1012AR supports multi-point applications using either a star or a daisy chain topology. together in a master/slave arrange- ment. Maximum distance between the units will vary based upon the number of drops, data rate, wire gauge, etc. Call Technical Support for specific distance estimates. In both topologies, the master unit should be set to “transmitter constantly on” (strap removed), and the slaves should be set to “transmitter controlled by RTS” (strap in place).

4.3 MULTIPOINT CONNECTION

HOST FIRST SLAVE OTHER SLAVE(S) XMT+ RCV+ RCV+ XMT- RCV- RCV- RCV+ XMT+ XMT+ RCV- XMT- XMT-

HOST FIRST SLAVE SECOND SLAVE XMT+ RCV+ RCV+

Figure 5. Daisy chain wiring for Model 1012AR host and slaves

RCVXMTXMT-

RCV+ XMT+ XMT+

XMTRCVRCV-

Figure 4. Star wiring for Model 1012AR host and slaves

Page 5 of the Patton electronic MODEL 1012AR user manual — APPENDIX B PAT TON MODEL 1012AR BLOCK DIAGRAM
Page 5 · click to enlarge
Page 5

Transmission Format: Asynchronous, full duplex Transmission Line: Two unconditioned twisted pair 19-26 AWG Interface: EIA/TIA 561 Data Rates: 0 - 38.4 Kbps Isolation: Minimum 1500 V RMS via custom transformers Surge Protection: 600W power dissipation at 1 mS and response time of 1 pS Control Signals: CTS follows RTS from the terminal (DTE); DSR follows DTR from the terminal (DTE); DCD indicates reception of carrier RTS/CTS Delay: Approximately 35 mS Connectors: 10 Pin RJ-45 on EIA/TIA-561 side; RJ-11 or 8 pin RJ-45 on line side Power Supply: No external power required; uses power from EIA data and control signals Temperature Range: 0-60°C (32-140°F) Altitude: 0-15,000 feet Humidity: 5 to 95% noncondensing Weight: 2 oz. Dimensions: 2.66” x 2.10” x 0.73”

PAT TON MODEL 1012AR SPECIFICATIONS

Data Wire Gauge Rate 19 24 26 38,400 6.0 4.0 2.5 19,200 6.0 4.0 2.5 9,600 6.0 4.0 2.5 4,800 6.0 4.0 2.5 2,400 6.0 4.0 2.5 1,200 6.0 4.0 2.5

Copyright © Patton Electronics Company All Rights Reserved

APPENDIX A

Distance Table (miles) Data RateWire Gauge 192426 38,400 19,200 9,600 4,800 2,400 1,2006.04.02.5
Patton electronic MODEL 1012AR — APPENDIX A diagram (page 5)
Fig. 2

APPENDIX B PAT TON MODEL 1012AR BLOCK DIAGRAM

Distance Table (miles)

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Patton electronic MODEL 1012AR

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Patton electronic MODEL 1012AR

Be the first to ask — other owners or our team will answer.

Original document

Patton electronic MODEL 1012AR manual PDF

5 pages·34 KB·Network Card·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…