Instruction/ maintenance manual of the product IM2RC/F Patton electronic
Go to page of 11
USER MANUAL MODEL IM2RC/F 64k Co-Directional Rack Mount Modem Rear Card SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://ww w .patton.
T ABLE OF CONTENTS Section Page 1. 0 W arranty Informatio n .............................................................2 1. 1 Radio and TV Interference 1. 2 CE Notice 1.3 Service Information 2. 0 General Informatio n ................................
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labo r . If any questions arise during installation or use of this product, please contact Patton Electronics T echnical Support at: (301) 975-1007.
Switch S1: Reserved for Future Use Switch S1 is reserved for future use and should remain in the Off position. Switch S2: Operation Mode Use Switch S2 to set the IM2RC/F for either Clear Channel or Octet T iming Mode. Most installations use Clear Channel (64kbps) Mode operation, though some installations may use Octet T iming Mode.
3.2 CONNECTING THE INTER F ACE DRIVER BOARD This package contains an interface driver board that allows you to configure your front function card for G.
NOTE: Please refer to the Model 1000RP Series User Manual AC and DC Rack Mount Power Suppli e s for fuse and power card replacement information. 4. 2 INS T ALLING THE REAR IM2RC/F CARD AND FRONT FUNCTION CARD The Model IM2RC/F is a rear-mountable G.
4.3.2 CONNECTING THE LINE INTER F ACE The Model IM2RC/F is to be used with Patton function card access products (i.e. 1045RC, 1092RC, 1092ARC, 2500RC) that support 64k/128k synchronous data rates. There are two essential requirements for connecting the line interface on Model IM2RC/F: 1 .
5.0 OPER A TION Once the Model IM2RC/F is installed and configured, it should operate transparentl y . This sections describes a typical application and general operating instructions. 5.1 TYPICAL APPLIC A TION The Model IM2RC/F allows a remotely connected LAN or high speed application to connect to the 64k/G.
APPENDIX B P A T T ON IM2RC/F CABLE RECOMMEND A TIONS All Patton Electronics Company Baseband Modems, CSU/DSUs and Short Range Modem are tested to the distances published in our Catalogs and Specification Sheets on twisted-pair cable with the following characteristics: Wire Gauge Capacitance Resistance 19 A WG 83nF/mi or 15.
APPENDIX D P A T T ON IM2RC/F 120 OHM G.703 INTER F ACE PIN ASSIGNMENT (RJ45 Female Connector) Pin Number Signal 1................................... . ......RX+ 2 ..........................................RX- 3 .......................................
APPENDIX E LINE INTER F ACE PIN ASSIGNMENT (RJ45 Female Connector) Pin Number Signal 1................................... . ......4-Wire RX+ 2 ..........................................4-Wire RX- 3 ..........................................no connection 4 .
An important point after buying a device Patton electronic IM2RC/F (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic IM2RC/F yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic IM2RC/F - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic IM2RC/F you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic IM2RC/F will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic IM2RC/F, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic IM2RC/F.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic IM2RC/F. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic IM2RC/F along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
