Instruction/ maintenance manual of the product 2085 Patton electronic
Go to page of 10
USER MANUAL SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M2085-D Doc# 047033UD Revised 4/15/97 MODEL 2085 High Speed RS-232 to RS-485 Interface Converter.
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 2085 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
3.1 SETTING THE DCE/DTE SWITCH For your convenience, the Model 2085 has an externally accessible DCE/DTE switch. If the device connected to the Model 2085 is a modem or multiplexer (or is wired like one), set the switch to “DTE”. This setting causes the Model 2085 to behave like Data T erminal Equipment and transmit data on pin 2.
3.4 CONFIGURA TION SWITCH APPLICA TIONS The switch settings generally needed to configure the Model 2085 for various applications are shown in the table below .
4.0 INST ALLA TION Once you have properly set the configuration switches, you are ready to connect the Model 2085 to your system. This section tells you how to properly connect the Model 2085 to the RS-485 and RS-232 interfaces, and how to operate the Model 2085.
4.1.3 4-WIRE CONNECTION USING TERMINAL BLOCKS If your RS-485 application requires you to connect two pairs of bare wires to the Model 2085, you will need to open the case to access the terminal blocks.
9. Insert the strain relief assembly with the wire going through it into the slot in the bottom half of the modem case and set it into the recess in the case. 10. BEND the top half of the case as necessary to place it over the strain relief assembly .
4.2.2 DAISY CHAIN TOPOLOGY Using a daisy chain topology , you may connect several Model 2085s together in a master/slave arrangement. Maximum distance between the units will vary based upon the number of drops, data rate, wire gauge, etc. Call T echnical Support for specific distance estimates.
APPENDIX B P A TTON MODEL 2085 RS-232 PIN CONFIGURA TIONS Copyright © Patton Electronics Company All Rights Reserved 1- (FG) Frame Ground 2- (TD) T ransmit Data T o Model 2085 3- (RD) Receive Data Fr.
An important point after buying a device Patton electronic 2085 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 2085 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 2085 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 2085 you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 2085 will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 2085, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 2085.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 2085. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 2085 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
