Instruction/ maintenance manual of the product 1180/35 Patton electronic
Go to page of 9
USER MANUAL MODEL 1180/35 Single Fiber V .35 Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part# 07M1 180/35-B Doc# 017071UB Revised 4/20/98 An .
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1 180/35 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
3.0 CONFIGURA TION The Model 1 180/35 uses an eight switch package that allow s configuration to a wide range of synchronous applications. Because all eight switches are externally accessible (see Figures 1 and 2, below), there is no need to open the Model 1 180/35's case for configuration.
S1-5 and S1-6: Clock Source Switches S1-1 and S1-2 are set in combination to determine the source of the transmit clock for the Model 1 180/35. S1-5 S1-6 Setting Of f Of f Received Recover Clock On Of f Internal Clock Of f On External Clock On On Internal Clock S1-7: DTE Control of RDL The setting for switch S1-7 determines whether the V .
5.0 OPERATION Once you have configured each Model 1 180/35 properly and connected the fiber and V .35 cables, you are ready to operate the units. This section describes reading the LED status monitors, power-up, and using the built-in loopback test modes.
5.2 POWER-UP / SYNCHRONIZA TION Apply AC power to the Model 1 180/35 by plugging the separate AC power adapter first into the rear panel outlet of the Model 1 180/35 and then into an acceptable AC power outlet. There is no power switch on the Model 1 180/35: When the "power" LED is glowing steady , the Model 1 180/35 is powered up.
APPENDIX A TROUBLESHOOTING SYMPT OM PROBLEM SOLUTION 5.4 POWER-DOWN T urn off the Model 1 180/35 by simply unplugging the AC power adapter from the wall.
APPENDIX B P A TTON MODEL 1 180/35 SPECIFICA TIONS T ransmission Format: Synchronous Range: 1.5 miles at all data rates, 3 miles at specified data rates Data rates: 2.4, 9.6, 14.4, 19.2, 28.8, 48, 38.4, 56, 64,128, 144, 192 and 256 Kbps Interface: ITU/CCITT V .
APPENDIX C INTERF ACE PIN ASSIGNMENT MODEL 1 180/35 - FEMALE M/34 CONNECTOR (V .35) Pin # Signal A Frame Ground B SGND (Signal Ground) C RTS D CTS E DSR F CD H DTR L LL (Local Loop) M TM (T est Mode) .
An important point after buying a device Patton electronic 1180/35 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1180/35 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1180/35 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1180/35 you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1180/35 will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1180/35, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1180/35.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1180/35. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1180/35 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
