Instruction/ maintenance manual of the product 1092A Patton electronic
Go to page of 19
USE R MAN UA L MODEL 1092 A High Speed, 2-Wire/4-Wire , Sync & Async Short Range Modem Part# 07M1092A- E Doc# 033031U D Revised 03/29/0 0 SALES OFFIC E (301)975-100 0 TECHNICAL SUPPOR T (301)975-100 7 http://ww w .
TABLE OF CONTENT S Sectio n Pag e 1. 0 Warranty Informatio n ............................................................ . 2 1. 1 Radio and TV Interferenc e 1.2. CE Notic e 1. 3 Service 2. 0 General Informatio n ......................................
1.3 SERVIC E All warranty and non-warranty repairs must be returned freigh t prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shippin g containe r . This number may be obtained from Patton Electronic s T echnical Service at : tel: (301)975-100 7 ; email: support@patton.
2.3 1092A SNMP MANAGEMENT SOLUTIONS Model 1092A is SNMP manageabl e when it is connected to a rack-mounted Model 1092ARC . SNMP management is enable d through a 1001MC rack management card located in the Patto n Electronics Rack System. 2.3.1 HTTP/HTML Managemen t The 1001MC maintains HTML pages that can be viewed through a web browse r.
7 3.1.1 Configuration DIP Switch Set “S1 ” Use the eight switches in DIP Switch Set “S1” to configure the dat a rate, asynchronous or synchronous data format, transmit clock sourc e and response to RDL request. The following table summarizes defaul t positions of DIP Switch S1.
9 Switch S1-8: Response to RD L Reques t Use Switch S1-8 to allow Model 1092A to enter the Remote Digita l Loopback diagnostic test when requested to do so by the far end Mode l 1092A For example, when Switch S1-8 is set to “ON”, it will enter RD L mode (See Section 5.
1 1 3.2 CONFIGURING THE SOFT WARE SWITCHE S The Model 1092A features a menu-driven command system tha t allows you to configure the local 1092A. Follow the instructions belo w to configure the Model 1.
1 3 MAIN MENU Option 2: Display Hardware Configuratio n Select Option 2 to display the configuration of the hardware DIP - switches. T o use the Hardware Configuration for the Activ e Configuration, select MAIN MEN U Option 5. Then select “Us e Hardware DIP-Switches”.
1 5 2. Data Forma t Select Option 2 in the SOFTWARE CONFIGUR ATIO N Menu t o select the async or sync data format (See below). 3. Clock Mod e Select Option 3 in the SOFTWARE CONFIGUR ATION Menu t o select the sync clock mode (See below) .
7. DTE Controlled Remote Digital Loo p Select Option 7 in the Menu t o enable DTE control of the Remote Digital Loop Menu (See below). Th e interface by selecting Enable (Option 1). To instruct the 1092A t o ignore this request from the DTE interface, select Disable (Option 2) .
1 9 The Model 1092A Test Modes are described on the following page. To run or terminate a particular test, key in the option to get to tha t screen menu. OF F T erminates all test s 51 1 Initiates the built-in test pattern generator and detector . 511 with Error s Initiates the built-in test pattern generator and detector.
2 1 3. Proper 2-Wir e Pairin g between the two modems is as follows : SIGNA L PIN # PIN # SIGNA L TI P 4 --------------------------------------- - 4 TI P RIN G 5 --------------------------------------- - 5 RIN G 4.
2 3 2) Hold the module with the faceplate toward you and align th e module with the guide slots in the rear panel of the Mode l 1092A. 3 ) While keeping the module’s faceplate parallel with the Mode l 1092A rear panel, slide the module straight in – so that the car d edge contacts line up with the socket inside the chassis.
2 5 4.3.2 Connecting to a DC Power Sourc e The 48 VDC power supply option uses a 3-pin terminal block wit h spring-type connectors. Please refer to the Model 1090 Series Servic e Manual . WARNING ! There are no user-serviceable parts in th e power supply section of the Model 1092A .
been placed in Test Mode. The unit can be placed in test mode by the local or remote user . N S Glow red to indicate that the local Model 1092A has not yet connected with the remote 5.3 TEST MODE S The Model 1092A offers two proprietary loopback test modes, plu s a built-in V .
5.3.3 Using the V .52 (BER) Test Pattern Generato r T o use the V .52 BER tests in conjunction with the Remote Digita l Loopback tests (or with Local Line Loopback tests), follow thes e instructions : 1. Locate the “5 11/511E” toggle switch on the front panel of the 1092A and move it U P .
APPENDIX B PA TTON ELECTRONIC S MODEL 1092A FACTORY REPLACEMEN T PART S AND ACCESSORIE S Patton Electronics Model # Descriptio n IM1/ A .............................. . V .24 with DB25 F IM1/ B .............................. . RS422/RS530 with DB25 F IM1/ C .
3 3 APPENDIX C PA TTON ELECTRONIC S MODEL 1092A INTERFACE PI N ASSIGNMEN T (Continued ) V .35 Interface (M/34F Female Connector ) (DCE Configuration ) Pin # Signa l B .......................... . SGND (Signal Ground ) C .......................... . RTS (Request to Send ) D .
APPENDIX D APPENDIX D PA TTON ELECTRONIC S MODEL 1092A CONTROL PORT PIN ASSIGNMEN T The 1092A control port is an 8 position connecto r, compliant wit h EIA/TIA-561 .
An important point after buying a device Patton electronic 1092A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1092A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1092A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1092A you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1092A will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1092A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1092A.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1092A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1092A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
