Instruction/ maintenance manual of the product 1089/I Patton electronic
Go to page of 12
USER MANU AL MODEL 1089/I 10BaseT HDSL Rocket Part# 07M1089/I-A Doc# 032071UA Revised 12/7/99 SALES OFFICE (301)975-1000 TECHNICAL SUPPORT (301)975-1007 http://www .
T T A A B B L L E E O O F F C C O O N N T T E E N N T T S S Section Page 1.0 W arranty Information .............................................................2 1.1 Radio and TV Interference 1.2. CE Notice 1.3 Service 2.0 General Information ........
1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Return Materials Authorization number on the outside of the shipping container . This number may be obtained from Patton Electronics T echnical Service at: tel: (301)975-1007 email: support@patton.
3 3 . . 0 0 C C O O N N F F I I G G U U R R A A T T I I O O N N The Model 1089 has two sets of eight DIP switches, which allow configuration for a wide variety of applications.
7 3.1.2 Configuration Switch Set “S3” Use the DIP Switches in Switch S3 to set the DTE Rate (for LAN Bandwidth Allocation), the transmit data sampling point and to reset the unit to its software default settings. The following table summa- rizes default positions of DIP Switch S3.
9 4 4 . . 0 0 I I N N S S T T A A L L L L A A T T I I O O N N When the Model 1089 has been properly configured, it may be connected to the DSL twisted pair interface, the 10BaseT Ethernet Interface, and the power source. This section describes these connec- tions.
11 4.4 POWER CONNECTION Universal AC Power (100-240V AC) The Model 1089 uses a 5VDC, 2A universal input 100-240V AC, power supply (center pin is +5V). The universal input power supply has a male IEC-320 power entry connector . This power supply con- nects to the Model 1089 by means of a barrel jack on the rear panel.
7 pulses = WAN receive frame(s) aborted 8 pulses = Detected WAN receive frame(s) with CRC 9 pulses = Detected LAN receive frame(s) too large 10 pulses = Detected LAN receive frame(s) not octet aligned.
(because it originates after the framer) and is intended to be evaluated only by another Processor . If the units are transmitting data and the pattern generator is enabled on one end of the link, the far end will begin receiving unframed packets and assume that the line has gone down.
5.3.2 Loops and Patterns The following section describes the Remote Loopback/BER test modes. Remote Digital When Remote Loop/51 1 or Remote Loop/51 1/E is enabled via the front panel switch, the Remote unit’s Restart T imer is set to one minute.
A A P P P P E E N N D D I I X X A A P P A A T T T T O O N N E E L L E E C C T T R R O O N N I I C C S S M M O O D D E E L L 1 1 0 0 8 8 9 9 S S P P E E C C I I F F I I C C A A T T I I O O N N S S Cloc.
A A P P P P E E N N D D I I X X D D P P A A T T T T O O N N E E L L E E C C T T R R O O N N I I C C S S M M O O D D E E L L 1 1 0 0 8 8 9 9 T T R R A A N N S S M M I I S S S S I I O O N N D D I I S S .
An important point after buying a device Patton electronic 1089/I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1089/I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1089/I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1089/I you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1089/I will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1089/I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1089/I.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1089/I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1089/I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
