Instruction/ maintenance manual of the product 1060 AC Powered Patton electronic
Go to page of 10
USER MANUAL MODEL 1060 AC Powered, Asynchronous Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .patton.com Part #07M1060-C Doc. #05801 1C Revised 1 1/3/97 CERTIFIED An ISO-9001 Certified Company Dear V alued Customer , Thank you for purchasing Patton Electronics products! W e do appreciate your business.
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1060 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
Control Input (C in ): The Control Input signal is used by the local Model 1060 as an input signal to activate its transmitter (“Enabled” settings) and allow data transmission to the remote device. This is required for half-duplex/ switched-carrier environments as well as in hardware flow control applications.
4.0 INSTALLATION The Model 1060 is easy to install. After configuring the DIP switches and DCE/DTE switches, connect the two twisted pairs using one of two methods: terminal blocks or RJ-1 1 jack. Figure 2 (below) shows the location of the terminal blocks and RJ-1 1 jack, as well as the female DB-25, on the rear of the Model 1060.
4.2 WIRING FOR MUL TIPOINT CIRCUITS The Model 1060 supports multi-point applications using either a star or daisy chain topology . Both topologies require special wiring, as well as specific DIP switch settings for master and slave units.
5.2.2 REMOTE ANALOG LOOP The second test mode is Remote Analog Loop. T o enter this mode, set one of the Model 1060s (local) in test mode by depressing the "Loopback T est" switch. Any characters sent from the remote 1060 will be returned to it (see Figure 5).
14 13 APPENDIX A P A TTON MODEL 1060 SPECIFICA TIONS T ransmission Format : Asynchronous T ransmission Line : 19 to 26 A WG twisted pair Range : (See table on page 14) Serial Interface : EIA RS-232 (CCITT V .
15 16 APPENDIX C P A TTON MODEL 1060 INTERF ACE PIN ASSIGNMENTS 1- (FG) Frame Ground 2- (TD) T ransmit Data T o Model 1060 3- (RD) Receive Data From Model 1060 4- (RTS) Request to Send T o Model 1060 .
17 18 APPENDIX E TROUBLESHOOTING SYMPTOM PROBLEM SOLUTION "TD" and "RD" LEDs indicate activity , but units will not communicate or data is garbled "TD" and "RD" LEDs indicate activity , but "CD" LED is unlit or red (should be green) Occasional data errors 1.
An important point after buying a device Patton electronic 1060 AC Powered (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1060 AC Powered yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1060 AC Powered - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1060 AC Powered you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1060 AC Powered will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1060 AC Powered, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1060 AC Powered.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1060 AC Powered. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1060 AC Powered along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
