Instruction/ maintenance manual of the product 1008 Patton electronic
Go to page of 10
USER MANUAL MODEL 1008 Ultra-Miniature, High Speed, Multipoint DB-9 Short Range Modem SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www .
1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1008 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment.
2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for One Y ear parts and labor .
T o access the Model 1008’s internal PC boards, insert a small flat- blade screwdriver between the connector and the lip of the case and twist gently as shown in Figure 3 (below). Both DIP switch S1 and S2 are marked with individual switch numbers 1 thru 4.
3.1.3 DIP SWITCH S2 SETTINGS DIP switch S2 is used to configure carrier control, RTS/CTS delay and communication protocol. The summary table below shows the factory default settings for switch S2. Following the summary table is a detailed description of each individual switch.
4.0 INST ALLA TION Once the Model 1008 is properly configured, it is ready to connect to your system. This section tells you how to properly connect the Model 1008 to the twisted pair and EIA/TIA-574 interfaces, and how to operate the Model 1008.
7. When you finish connecting the wires to the terminal block, the assembly should resemble the diagram below: 8. Place the 2 halves of the strain relief assembly on either side of the telephone wire and press together very lightly . Slide the assembly so that it is about 2 inches from the terminal posts and press together firmly .
When connecting two Model 1008s, it is necessary to use a crossover cable. The diagrams below show how a crossover cable should be constructed for the following environments: 4-wire RJ-1 1, 4-wire RJ-45, 2-wire RJ-1 1 or 2-wire RJ-45.
Figure 6 (below) shows how to wire the two-pair cables properly for a Model 1008 daisy chain topology . Note that the ground connection is not needed. 4.3 CONNECTION TO THE EIA/TIA-574 INTERF ACE The Model 1008 is designed to plug directly into the DB-9 serial port of an EIA/TIA-574 DTE device (PC, laptop, host).
APPENDIX B P A TTON MODEL 1008 EIA/TIA-574 INTERF ACE DB-9 SIGNAL 1 -----------------CD 2 -----------------RD 3 -----------------TD 4 -----------------DTR 5 -----------------SG/FG 6 -----------------D.
An important point after buying a device Patton electronic 1008 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Patton electronic 1008 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Patton electronic 1008 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Patton electronic 1008 you will learn all the available features of the product, as well as information on its operation. The information that you get Patton electronic 1008 will certainly help you make a decision on the purchase.
If you already are a holder of Patton electronic 1008, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Patton electronic 1008.
However, one of the most important roles played by the user manual is to help in solving problems with Patton electronic 1008. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Patton electronic 1008 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
