Instruction/ maintenance manual of the product 827 ParaBody
Go to page of 10
827 LAT MACHINE j )1 t = it) it) WARNING: Read and follow all directions for each step to insure proper assembly of this product. CLASSH P A.RT # 7077901 REV A USER'S GUIDE 1 Version: 827107 Revi.
LIFE FITNESS 14150 Sunfish Lake B)~~~ . Ramsey Minnesota, 55303 U.S.A. Tel: 763.323.4500 ··l~ax: 763.323.4797 800.328.9714 (Toll-free within. the U.S.
TABLE OF CONTENTS LIMITED WARRANTY Para Body extends the following LIMITED WARRANTY to the original owner of the Para Body products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the Para Body product or a weld should crack or break, it will be repaired or replaced by ParaBody.
'IMPORTANT NOTESI Please note: * Thank you for purchasing the ParaBody LAT MACHINE. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
Minimum Required Usable Space Length = 82 inches (208.5 cm) 6' 10" Width = 71 inches (180.5 cm) 5'11" Height = 83 inches (211 cm) 6' 11" 1 Square = l' X l' 5' 4 3' 2' l' I I l= ~ r '.1 •.
PARTS LIST KEY PART # DESCRIPTION QfY KEY PART # DESCRIPTION QfY 1 6759108 BASE 1 21 6590801 3 X 2" INSERT GUIDE 2 2 6758908 FRONT UPRIGHT 1 22 6387901 5" VINYL CAP 2 3 6760008 REAR UPRIGHT 1 23 3105401 STARLOCK COLLAR 2 4 6759608 TOP BOOM 1 24 3116001 1-114" SQ.
[ 6 I 1/2 I I 5 I 1/2 I I 4 I 1/2 I 6 I 3 I 1/2 I I 2 1/2 I I 1 1/2 I I o I FIGURE 1 STEP 1: • Attach two 2" SQ. COVER CAPS (18) onto the ends ofthe REAR UPRIGHT (3) as shown in FIGURE 1. • Insert two 3 X 2" END CAPS (19) into the ends of the BASE (1) and REAR UPRIGHT (3) as shown in FIGURE 1.
7 FI STEP 8: Attach the CABLE (12) from the TOP BOOM (4) to the CARRIAGE (5) using one QUICK LINK (37) as shown in FIGURE 8. (IMPORTANT! Securely tighten QUICK LINK.) • Place one 4-112" PULLEY (15) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown in FIGURE 8.
I FIGURE 7 FIGURE 4 STEP 7: STEP 4: • Insert two 2" SQ. END CAPS (17) into the FRONT UPRIGHT (3) as shown in FIGURE 4. • LOOSELY assemble the FRONT UPRIGHT (3) to the BASE (1) using two 112 X 4" BOLTS (32) and two 112" LOCK NUTS (28).
FIGURE 5 STEP 5: • CAREFULLY slide the ROLLER PAD SUPPORT (6) over into the FRONT UPRIGHT (2) and engage the SPRING PIN into one of the adjustment holes. See FIGURE 5. o CAREFULLY slide the CARRIAGE (5) over into the REAR UPRIGHT (3) as shown in FIGURE 5.
An important point after buying a device ParaBody 827 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 827 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 827 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 827 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 827 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 827, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 827.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 827. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 827 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
