Instruction/ maintenance manual of the product 093 ParaBody
Go to page of 12
BODYSMITH PROSYSTEM MAiN UNIT 093 PRODUCT ASSEMBLY I[NSTRUCTTON, S~ETS TOOLS I~._EQUIR.E. D FOR ASSEI~BLY 9~16 iqh’CH SOCKET AD~ISTABLE WRENCH RUBBER/VL4.LLET or ~R REVISION: K if you experience any problem w~th the assembly of this product, plms~ co:atact your ¯ or your PAP~,.
093 BODYSiVfIT~ PROSYSTEM ASSEMBLY PARTS L~ST SORT AND COUNT ALL PARTS BEFORE BEGYNNING ASSEiV[BLY ~AP, D%VARE: I_TCLM NAME/DESCPJPTION QTY 3. 4. 5. 6. 7. "8. 9. I0. II. 12. .13. 14. !5. 16. i7. 18. 19. .~/8 X 3-//4 IN. BOLT .....................
09.3 BODYS1V][!TH PROSYSTE1V[ ASSEMBLY PARTS LIST SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY W~LDM-ENTS/’PARTS: " ITEM N.~dV[E/DESCR/PTION QTY 2. 3. 4. 5. 6. 7. 8. 9. lO. 11. 12. I3. 14. 15. 16. 17. 18. 19. 20. 21. 22. MAIN UPRIGHT ....
093 BODYSM]~TH PROSYSTEiV~ ASSE1V~BLY INSTRUCTIONS [NIP. ORTANT.: ¯ TIlE BODYSMITH PROSYSTEM MUST BE ASSEMBLED ON A FLAT LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. ¯ PARABODY, INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ~SSEMBLED .BY TWO PERSONS TO AVOID POSSIBLE INJURY.
093 o I1. - 12. 13. 14. 15. 16. BODYSMITi-I PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (I) 1-1/4 SQ. RUBBER BUMPER to the CENTER of the CARRIAGE STOP on the WEIGHT CARRIAGE. Slide WEIGHT CARRIAGE down over the REAR UPRIGHT of the MAIN UPRIC-;HT. (NOTE: MAKE SURE THAT THE WEIGHT PEG ON THE WEIGHT CAP,.
093 17. 18. 19. 20. 21. 22. NOTE: 23. NOTE: BODYSI~tTU PROSYSTEM ASSEMBLY INSTRUCTIONS Attach one (1.) 3/4 X 2 IN. PAP,.AGLIDE St’RIP and one (I) 1-1/2 X2 IN. PARAGLIDE STRIP to ADJUSTABLE KNEE SUPPORT as shown in (’DETAIL E) using the following steps: A.
093 24. 25. .26. 27. 29. 30; BODYSMiTH PROSYSTEM ASSEMBLY INSTRUCTIONS To install SECONDARY CABLE (PB2559-1), start by inserting the end of the CABLE, WITHOUT the WHITE BALL under the FRONT PULLEY in the LOW ROW PULLEY HOUSING on the MAIN UPRIGHT.
093 BODYS!Vf!TN PROSYSTEM ASSE!VLBLY INSTRUCTIONS ~~ S~ SNAP ~OO~ ~ FASTENED ~EFO~ DOLNG EXERCISES "~ WARNING ~’ DO NOT OPERATE TIIIS IV!ACH!NE W!TI-! LAT BAR OFF SAFETY HOOKS EXCEPT DURING I~IGH PULLEY EXERCISES !!! WAR.
TOP UPRIGHT SUPPORT ~ ,.3/8 LOCKWASHE:R I.AT BAR HOLE MAIN UPRI BAR HOLDER (2) (~:E I:::~TAIL" F’) ;ERIAL .NUMBER FRONT UPRIGHT ROW BAR HOLDER.
.
DETAIL’A" 3/B x 3-~,/~. BOLT (2) NUT TYP. LOCKFh’ASNER WASHER TYP. KNEE SUPPORT (SEE DETAIL NU’r (2). LOCKWASHER (2.) ~/20.D. X 1 IN BUSHING NUT (2).
(5{~: DE TAI L’F" LOW ROW FOOT BRACE.
An important point after buying a device ParaBody 093 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ParaBody 093 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ParaBody 093 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ParaBody 093 you will learn all the available features of the product, as well as information on its operation. The information that you get ParaBody 093 will certainly help you make a decision on the purchase.
If you already are a holder of ParaBody 093, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ParaBody 093.
However, one of the most important roles played by the user manual is to help in solving problems with ParaBody 093. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ParaBody 093 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
