EN
Packard Bell logo
Official user manual

Packard Bell MX

19 pages·2.1 MB·Laptop·PDF·ENDEFRITNLJA
Packard Bell MX
Table of Contents 33 sections Packard Bell · EasyNote MX · Disassembly Manual · Disassembly Manual · … ShowHide
Page 1 of the Packard Bell MX user manual — EasyNote MX
Page 1 · click to enlarge
Page 1

Packard Bell

Packard Bell MX — Packard Bell diagram (page 1)
Fig. 1 · Packard Bell

EasyNote MX

Disassembly Manual

Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 2 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 3 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 4 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 5 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 6 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 7 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 8 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 9 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 10 · EasyNote MX
Packard Bell MX — EasyNote MX diagram (page 1)
Fig. 11 · EasyNote MX
Page 3 of the Packard Bell MX user manual — Required Tools All disassembly procedures can be performed using the following tools:
Page 3 · click to enlarge
Page 3

Overview This document contains step-by-step disassembly instructions for the Packard Bell EasyNote MX. The instructions are illustrated where necessary with images of the part that is being removed or disassembled.

Packard Bell reserves the right to make changes to the EasyNote MX without notice.

Technician Notes Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances.

Disassembly When disassembling the system unit, follow these general rules:

„ Turn off the power using the power button. „ Disconnect the adapter. „ Remove any SD/MMC card, ExpressCard or dummy card from the device. „ Do not disassemble the system into parts that are smaller than those specified in the instructions. „ Label all removed connectors; note where the connector goes and in what position it was installed.

Reassembly Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned to their proper positions. Check that no tools or any loose parts have been left inside the casing. Check that everything is properly installed and tightened.

Required Tools All disassembly procedures can be performed using the following tools:

„ Small Phillips and flat-blade screwdriver.

Page 4 of the Packard Bell MX user manual — Avoid Electrostatic Discharge
Page 4 · click to enlarge
Page 4

Hazardous Voltage There is hazardous voltage present inside the notebook when it is connected to an AC supply, even when the notebook’s power switch is off. Exposure to hazardous voltage could cause personal injury. To avoid risk of injury, contact an Authorized Service Provider for proper (un)installation of optional hardware devices.

Avoid Electrostatic Discharge Electrostatic electricity can easily damage circuit cards and integrated circuits (ICs). To reduce risk of damage, store them in protective packaging whenever they are not installed in the system.

Add-in cards can be extremely sensitive to ESD and always require careful handling. After removing the card from the notebook, place the card flat on a grounded, static-free surface, component-side up. Use a conductive foam pad if available, but not the card wrapper. Do not slide the card over any surface.

Before you install or remove memory modules, video memory, disk drives, circuit cards or other devices, protect them from static electricity. To do so, make sure the notebook’s power switch is OFF. Then, unplug the notebook’s AC power cord. Before picking up the device you (un)install, you should wear an anti- static wrist wrap (available at electronic supply stores). Be sure to connect the wrist wrap to an unpainted metal portion of the notebook casing. As an alternative, you can dissipate electrostatic build-up by touching an unpainted metal portion of the notebook casing with one hand. Then touch the device you are (un)installing with the other hand, and maintain continuous contact with it until it is (un)installed in the notebook.

Power Supply Unit Under no circumstances should you attempt to disassemble the power supply. The power supply contains no user-serviceable parts. Inside the power supply are hazardous voltages that can cause serious personal injury. Always return a defective power supply to the dealer.

Page 5 of the Packard Bell MX user manual — Battery Perform the following steps to remove the battery:
Page 5 · click to enlarge
Page 5

Battery Perform the following steps to remove the battery:

1. Make sure the power is off. 2. Turn the notebook upside down.
3. Push the 2 locks in the direction of the arrows to the release the battery compartment cover and remove the cover. 4. Take the battery out of the compartment.
Packard Bell MX — Battery Perform the following steps to remove the battery: diagram (page 5)
Fig. 12 · Battery Perform the following steps to remove the ba…
Packard Bell MX — Battery Perform the following steps to remove the battery: diagram (page 5)
Fig. 13 · Battery Perform the following steps to remove the ba…

Fig. 1 Removing battery.

Hard Disk Drive To remove the HDD, first remove the battery (see Battery) and then perform the following steps:

1. Remove the 2 screws on the hard disk drive cover and remove the cover (see Fig. 1 ). 2. Pull the plastic tab on the hard disk drive towards you as shown in Fig. 2 to disconnect the drive.
Packard Bell MX — Battery Perform the following steps to remove the battery: diagram (page 5)
Fig. 14 · Battery Perform the following steps to remove the ba…

Fig. 2 Removing hard disk drive.

3. Take the drive out of its compartment.
Page 6 of the Packard Bell MX user manual — Optical Disk Drive
Page 6 · click to enlarge
Page 6
4. Remove the 4 screws on the metal bracket to separate it from the hard disk drive.
Packard Bell MX — Optical Disk Drive diagram (page 6)
Fig. 15 · Optical Disk Drive

Fig. 3 Location of hard disk drive bracket screws.

Optical Disk Drive To remove the CD-ROM or DVD drive, first remove the battery (see Battery), remove the HDD cover (see Hard Disk Drive) and then perform the following steps:

1. Locate and remove the screw securing the optical disk drive in the hard disk drive compartment.
Packard Bell MX — Optical Disk Drive diagram (page 6)
Fig. 16 · Optical Disk Drive

Fig. 4 Location of optical disk drive screw.

2. Use the emergency eject hole to open the optical disk drive. 3. Take out the optical disk drive from the drive bay.

WLAN Card To remove the WLAN card, first remove the battery (see Battery) and then perform the following steps:

1. Remove the 7 screws retaining the CPU cover (see Fig. 1 ).
Page 7 of the Packard Bell MX user manual — Memory
Page 7 · click to enlarge
Page 7
2. Disconnect the wireless antenna cables.
Packard Bell MX — Memory diagram (page 7)
Fig. 17 · Memory

Fig. 5 Location of WLAN antenna cable connectors.

3. Release the 2 metal clips securing the WLAN card.
Packard Bell MX — Memory diagram (page 7)
Fig. 18 · Memory

Fig. 6 Releasing metal clips.

4. Take out the WLAN card from the slot.

Memory To remove the memory installed, first remove the battery (see Battery) and then perform the following steps:

1. Remove the 7 screws retaining the CPU cover (see Fig. 1 ).
Page 8 of the Packard Bell MX user manual — Processor
Page 8 · click to enlarge
Page 8
2. Release the metal clips securing the memory module(s) and remove the module(s).
Packard Bell MX — Processor diagram (page 8)
Fig. 19 · Processor

Fig. 7 Removing memory module.

Processor To remove the CPU, first remove the battery (see Battery) and then perform the following steps:

1. Remove the 7 screws retaining the CPU cover (see Fig. 1 ). 2. Remove the 2 screws holding the CPU fan.
Packard Bell MX — Processor diagram (page 8)
Fig. 20 · Processor

Fig. 8 Location of CPU fan screws.

3. Disconnect the power cable and remove the CPU fan cover.
Page 9 of the Packard Bell MX user manual — Keyboard
Page 9 · click to enlarge
Page 9
4. Remove the 4 screws securing the heat sink in designated order.
Packard Bell MX — Keyboard diagram (page 9)
Fig. 21 · Keyboard

Fig. 9 Location of heat sink screws.

5. Remove the heat sink. 6. Turn the screw in the CPU socket 180 degrees to release the CPU. 7. Take out the CPU.

Keyboard To remove the keyboard, first remove the battery (see Battery) and then perform the following steps:

1. Remove the 7 screws retaining the CPU cover (see Fig. 1 ). 2. Remove the 4 screws labelled K> .
Packard Bell MX — Keyboard diagram (page 9)
Fig. 22 · Keyboard

Fig. 10 Location of K> screws.

3. Turn the notebook over so the top is facing up.
Page 10 of the Packard Bell MX user manual — LCD Screen Assembly
Page 10 · click to enlarge
Page 10
4. There are 4 small slots at the location shown in Fig. 11 ; insert a small flat-blade screwdriver in each slot to unlatch the keyboard.
Packard Bell MX — LCD Screen Assembly diagram (page 10)
Fig. 23 · LCD Screen Assembly

Fig. 11 Location of latches securing keyboard cover.

5. Tilt the keyboard gently forward. 6. Before removing the keyboard entirely, carefully disconnect the keyboard flat cable from the main board.

LCD Screen Assembly To remove the LCD screen assembly, remove the battery (see Battery), disconnect the wireless antenna cables (see WLAN Card), and then perform the following steps:

1. Turn the notebook upside down. 2. Remove the 4 screws shown in Fig. 12 .
Packard Bell MX — LCD Screen Assembly diagram (page 10)
Fig. 24 · LCD Screen Assembly

Fig. 12 Removing 4 bottom screws.

3. Turn the notebook over so the top is facing up.
Page 11 of the Packard Bell MX user manual — LCD Screen Assembly
Page 11 · click to enlarge
Page 11
4. Remove the 4 hinge screws on the back of the notebook securing the LCD screen.
Packard Bell MX — LCD Screen Assembly diagram (page 11)
Fig. 25 · LCD Screen Assembly

Fig. 13 Location hinge screws.

5. Remove the middle hinge cover. 6. Carefully disconnect the 2 (white) block connectors.
Packard Bell MX — LCD Screen Assembly diagram (page 11)
Fig. 26 · LCD Screen Assembly

Fig. 14 Location of block connectors and screws.

7. Slide the left and the right hinge cover outward. 8. Remove the screw in the left and the right hinge.
Packard Bell MX — LCD Screen Assembly diagram (page 11)
Fig. 27 · LCD Screen Assembly

Fig. 15 Location of screw in hinge.

9. Turn the notebook upside down. 10. Remove the tape (if used) securing the WLAN antenna cable and unhook it from the plastic tabs.
Packard Bell MX — LCD Screen Assembly diagram (page 11)
Fig. 28 · LCD Screen Assembly

Fig. 16 The wireless antenna cable.

1010101010

Page 12 of the Packard Bell MX user manual — Main Board
Page 12 · click to enlarge
Page 12
11. Lift away the LCD screen assembly.

Main Board To remove the main board, first remove the battery (see Battery), the HDD (see Hard Disk Drive), the CD- ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), and then perform the following steps:

1. Turn the notebook over so the top is facing up. 2. Remove the 4 screws that were covered by the LCD screen and the 4 screws in the heat plate.
Packard Bell MX — Main Board diagram (page 12)
Fig. 29 · Main Board

Fig. 17 Location of screws.

3. Turn the notebook upside down. 4. Remove the 4 small screws in the hard disk drive compartment.
Packard Bell MX — Main Board diagram (page 12)
Fig. 30 · Main Board

Fig. 18 Location of screws in HDD compartment.

1111111111

Page 13 of the Packard Bell MX user manual — Modem
Page 13 · click to enlarge
Page 13
5. Remove the 8 remaining screws from the bottom plate. 6. Remove the dummy card (optional) from the card reader and/or the ExpressCard slot. 7. Carefully remove the top cover.
8. Disconnect the speaker cable (red/black twisted wires) and the optional subwoofer cable (white/black and red/black twisted wires).
Packard Bell MX — Modem diagram (page 13)
Fig. 31 · Modem

Fig. 19 Location of screws and speakers and subwoofer cables.

9. Carefully disconnect the optional Bluetooth cable from the main board (see Fig. 21 ). 10. Remove the 3 screws securing the main board (see Fig. 19 ) 11. Extract the main board from the casing. 12. Optionally, you might need to remove the modem (see Modem ).

Modem To remove the modem, first remove the battery (see Battery), the HDD (see Hard Disk Drive), the CD- ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), the main board (see Main Board), and then perform the following steps:

1. Disconnect the modem cable from the modem. 2. Remove the 2 screws securing the modem and take out the modem.
Packard Bell MX — Modem diagram (page 13)
Fig. 32 · Modem

Fig. 20 Location of modem screws.

1212121212

Page 14 of the Packard Bell MX user manual — Bluetooth (Optional)
Page 14 · click to enlarge
Page 14

Bluetooth (Optional) To remove the optional Bluetooth module, first remove the battery (see Battery), the HDD (see Hard Disk Drive), the CD-ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), the main board up to step 8 (see Main Board), and then perform the following steps:

1. Carefully disconnect the Bluetooth cable.
Packard Bell MX — Bluetooth (Optional) diagram (page 14)
Fig. 33 · Bluetooth (Optional)

Fig. 21 Location of Bluetooth module and connector.

2. Extract the Bluetooth module; the module has been clicked into place (see Fig. 21 ).

Touchpad To remove the touchpad, first remove the battery (see Battery), the HDD (see Hard Disk Drive), the CD- ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), the main board top cover up to step 7 (see Main Board), and then perform the following steps:

1. Remove the 2 screws securing the touchpad buttons board to the top cover.
Packard Bell MX — Bluetooth (Optional) diagram (page 14)
Fig. 34 · Bluetooth (Optional)

Fig. 22 Location of touchpad buttons board.

1313131313

Page 15 of the Packard Bell MX user manual — Speakers
Page 15 · click to enlarge
Page 15
2. Disconnect the 2 flat cables and separate the part from the top cover (see Fig. 22 ).

Speakers To remove the speakers, first remove the battery (see Battery), the HDD (see Hard Disk Drive), the CD- ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), the main board top cover up to step 7 (see Main Board), and then perform the following steps:

1. Disconnect the speaker cable from the main board (see Fig. 19 ). 2. Remove the 2 screws on both speakers and remove the speakers.
Packard Bell MX — Speakers diagram (page 15)
Fig. 35 · Speakers

Fig. 23 Location of speaker assembly screws.

Subwoofer (Optional) To remove the optional subwoofer, first remove battery (see Battery), the HDD (see Hard Disk Drive), the CD-ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), the main board top cover up to step 7 (see Main Board), and then perform the following steps:

1. Disconnect the subwoofer cable from the main board.
Packard Bell MX — Speakers diagram (page 15)
Fig. 36 · Speakers

Fig. 24 Disconnecting the subwoofer cable.

1414141414

Page 16 of the Packard Bell MX user manual — LCD Panel
Page 16 · click to enlarge
Page 16
2. Remove the 3 screws securing the subwoofer (one of the screws is not visible in Fig. 25 ).
Packard Bell MX — LCD Panel diagram (page 16)
Fig. 37 · LCD Panel

Fig. 25 Location of subwoofer screws.

3. Remove the subwoofer assembly.

LCD Panel To disassembly the LCD panel, first remove battery (see Battery), the HDD (see Hard Disk Drive), the CD-ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), and then perform the following steps:

1. Remove the 5 rubber stoppers.
Packard Bell MX — LCD Panel diagram (page 16)
Fig. 38 · LCD Panel

Fig. 26 Location of rubber stoppers.

2. Remove the 5 screws that appeared after removing the rubber stoppers (see Fig. 26 ). 3. Carefully remove the LCD cover which has been clicked into place. 4. Disconnect the power cable from the inverter board.
Packard Bell MX — LCD Panel diagram (page 16)
Fig. 39 · LCD Panel

Fig. 27 Location of inverter board.

1515151515

Page 17 of the Packard Bell MX user manual — Inverter Board
Page 17 · click to enlarge
Page 17
5. Remove the 8 screws securing the LCD and lift out the LCD panel.
Packard Bell MX — Inverter Board diagram (page 17)
Fig. 40 · Inverter Board

Fig. 28 Location of screws securing LCD module.

6. Remove the 4 screws on each side of the bracket. 7. Remove the top support bracket (usually held in place by the left and the right brackets). 8. Disconnect the LCD cable from the back of the panel.

Inverter Board To remove the inverter board, first remove battery (see Battery), the HDD (see Hard Disk Drive), the CD- ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), disassemble the LCD panel up to step 3 (see LCD Panel), and then do the following:

1. Disconnect all cables from the inverter board (see Fig. 27 ). 2. Remove the screw securing the inverter board (see Fig. 27 ) and extract the board.

Webcam To remove the webcam, first remove battery (see Battery), the HDD (see Hard Disk Drive), the CD-ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), disassemble the LCD panel up to step 3 (see LCD Panel), and then do the following:

1. Disconnect the cable from the webcam.
Packard Bell MX — Inverter Board diagram (page 17)
Fig. 41 · Inverter Board

Fig. 29 Location of webcam connector.

2. Lift out the webcam.

1616161616

Page 18 of the Packard Bell MX user manual — Webcam Microphone/USB Cable
Page 18 · click to enlarge
Page 18

Webcam Microphone/USB Cable To remove the webcam microphone and the webcam USB cable, first remove battery (see Battery), the HDD (see Hard Disk Drive), the CD-ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), disassemble the LCD panel up to step 5 (see LCD Panel), and then do the following:

1. Disconnect the cable from the webcam (see Fig. 29 ). 2. Remove the USB cable; the microphone cable is attached to the same cable.

WLAN Antenna To remove the wireless antenna, first remove battery (see Battery), the HDD (see Hard Disk Drive), the CD-ROM or DVD drive (see Optical Disk Drive), the wireless network card (see WLAN Card), the installed memory (see Memory), the CPU (see Processor), the keyboard (see Keyboard), remove the LCD screen (see LCD Screen Assembly), disassemble the LCD panel up to step 5 (see LCD Panel), and then do the following:

1. Remove the wireless antenna from the shielding foil in the LCD cover.
Packard Bell MX — Webcam Microphone/USB Cable diagram (page 18)
Fig. 42 · Webcam Microphone/USB Cable

Fig. 30 Location WLAN antenna cables.

1717171717

Page 19 of the Packard Bell MX user manual — Notice
Page 19 · click to enlarge
Page 19

This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B.V.

PACKARD BELL B.V. SHALL NOT BE HELD LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.

Copyright © 2006 Packard Bell B.V. All rights reserved.

Packard Bell is a trademark of Packard Bell B.V. The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks of their respective owners.

The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement.

EasyNote MX Disassembly Manual Author: Wouter Willemse & Juan M. Calviño First Edition: August 2006 Version: 1.0 Part Number: 7417600000

Packard Bell B.V. www.packardbell.com

1818181818

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Packard Bell MX

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Packard Bell MX

Be the first to ask — other owners or our team will answer.

Original document

Packard Bell MX manual PDF

19 pages·2.1 MB·Laptop·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…