Instruction/ maintenance manual of the product CV352 NuTone
Go to page of 12
BUIL T -IN CENTRAL CLEANING SYSTEM MODEL: CV -352 GENERAL INFORMATION .............. 2 LAYOUT AND PLANNING ............... 2 Examples ........................................2 Locating the Power Unit ..................3 Locating the Wall Inlets ......
2 GENERAL INFORMA TION LA YOUT AND PLANNING EXAMPLES The Nu T one Central Cleaning System consists of a Central Power Unit, PVC Tubing, PVC Fittings, automatic switch operated Wall Inlets, a flexible hose and various cleaning attachments. As an aid in planning the installation, look at the following examples.
3 FIGURE 3 THE SPLIT -LEVEL HOUSE Like the two-story house, the split level installation commonly calls for a two-level trunk line. Here, the power unit is located in the garage. The intake tubing runs exposed up the garage wall and into the ground level section's attic.
4 INST ALLA TION IN NEW CONSTRUCTION W ALL INLET ROUGH-IN 1. Once the locations for wall inlets have been determined, mount all inlet brackets. 2. To locate bracket on wall stud, measure approximately 18" up from finished floor level. (Height may vary according to individual preference.
5 FIGURE 7 INCLUDE FITTING RECESS IN MEASUREMENT TUBING MEASUREMENT PVC TUBING FIT TING FIT TING 3 / 4 " 3 / 4 " FIGURE 8 FIGURE 9 FIGURE 10 FIGURE 11 FIGURE 12 TUBING INST ALLA TION 1. Cut a 2 1 ⁄ 2 " diameter hole in sole plate, header or stud directly in line with opening of inlet bracket fitting.
6 FIGURE 15 FIGURE 16 MODEL 365 DOUBLE FLANGED TEE W ALL INLET MOUNTING BRACKET SHORTEN W ALL FIGURE 13 FIGURE 14 W ALL INLET INST ALLA TION MODEL 360 W ALL INLET(361 Rough in) 1. Once the walls have been finished, install the wall inlets. 2. Remove the cardboard plaster guard.
DIMENSIONAL CHART MODEL DIMENSION CV-352 A 27" B7 3 ⁄ 4 " C6 1 ⁄ 2 " D1 3 5 ⁄ 8 " 7 POWER UNIT INST ALLA TION MOUNTING See Figure 18. 1. Locate the power unit within six feet of a grounded electrical outlet. 2. Drill 3 ⁄ 16 " diameter pilot holes for the two (2) mounting screws in a wall stud or strong support.
8 INST ALLA TION IN EXISTING CONSTRUCTION LA YOUT AND PLANNING The general layout and planning and the component locations are the same for existing construction.
9 4. Be sure tubing hole is centered in sole plate and directly in line with proposed wall inlet cutout. NOTE: If 330 wall inlet is being used refer to Model 330 Wall Inlet Installation on next page. 5. If area is clear, cut an inlet opening in the wall approximately 18" above the floor.
10 MOUNTING PLA TE MOUNTING HOLE (2) ELBOW FIGURE 32 MOUNTING PLA TE INLET FIGURE 33 1. Make cutout according to dimensions in Figure 30. 2. Refer to Figure 31. Break off nail plate at scored line. 3. Refer to Figure 32. Glue elbow to mounting plate, place assembly into cutout, and attach elbow to tubing inside the wall.
11 FLOOR SUB-FLOOR 2 9 / 16 " 3 1 / 16 " INLET EXTENSION FLOOR INLET FRAME MOUNTING BRACKET SEAL FLANGED FITTING FIGURE 36 CUT TO LENGTH EXTENSION SLEEVE FLANGED FITTING MOUNTING BRACKET FLA.
Product specifications subject to change without notice. Printed in U.S.A., Rev. 4/01, Part No. 84912 T wo Y ear Limited W arranty WARRANTY OWNER: NuTone warrants to the original consumer purchaser of.
An important point after buying a device NuTone CV352 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NuTone CV352 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NuTone CV352 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NuTone CV352 you will learn all the available features of the product, as well as information on its operation. The information that you get NuTone CV352 will certainly help you make a decision on the purchase.
If you already are a holder of NuTone CV352, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NuTone CV352.
However, one of the most important roles played by the user manual is to help in solving problems with NuTone CV352. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NuTone CV352 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
