Instruction/ maintenance manual of the product WS2 NuTone
Go to page of 16
Page 1 ALLURE ® WS2 SERIES RANGE HOOD ! W ARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
Page 2 ALLURE ® WS2 SERIES RANGE HOOD CABINET BOTTOM CABINET FRONT HORIZONTAL DUCT ACCESS HOLE 5¼" 5¼" 7½" 1 / 8 " ¾" 13 15 / 16 " (30" hood) 16 15 / 16 " .
Page 3 ALLURE ® WS2 SERIES RANGE HOOD PREP ARE THE HOOD 4 Remove either top or back wiring knockout and install approved Electrical Cable Clamp . ELECTRICAL CABLE CLAMP Ducted Installation - Skip to Step 11 . The following Steps (5 thru 10) are for NON-DUCTED INST ALLA TION ONL Y .
Page 4 ALLURE ® WS2 SERIES RANGE HOOD PREP ARE THE HOOD 13 3¼” x 10” Ducted Discharge Only: Remove T ape from damper flap and attach Damper/Duct Connector over knockout opening with screws removed in Step 4 under “PREPARE THE HOOD”. Make sure damper Piv ot is nearest to T op/Bac k Edg e of hood.
Page 5 ALLURE ® WS2 SERIES RANGE HOOD INST ALL HOOD KEYHOLE (4) MOUNTING SCREW (4) 1 Hang hood from (4) Mounting Screws . Slide hood towards wall until mounting screws are engaged in narrow end of (4) Keyholes . Tighten mounting screws securely. A long screwdriver works best.
Page 6 ALLURE ® WS2 SERIES RANGE HOOD OPERA TION Fan and Lights: 3 push button switches for each. Push any button to select one of 3 fan speeds or one of 3 light levels. Push the same button to turn fan or light off. Press another button to change fan speed or light level.
Page 7 ALLURE ® WS2 SERIES RANGE HOOD SER VICE P AR TS KEY NO. P ART N O. DESCRIPTION 2 R740013 Damper/Duct Connector (includes hardware) 3 R602017 Screw, #8-18 x ¼ Hex* (2 in package) 4 R334755 Mot.
Page 8 ALLURE ® WS2 SERIES RANGE HOOD 628004B W ARRANTY NUT ONE ONE YEAR LIMITED W ARRANTY NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase.
Page 9 ALLURE ® WS2 SERIES RANGE HOOD HOTTE DE CUISINIÈRE DE LA SÉRIE ALLURE ® WS2 ! A VERTISSEMENT AFIN DE DIMINUER LES RISQUES D’INCENDIE, D’ÉLECTROCUTION OU DE BLESSURES, SUIVEZ CES DIRECTIVES : 1. Utilisez ce produit en suivant les recommandations du manufacturier.
Page 10 ALLURE ® WS2 SERIES RANGE HOOD PRÉP AREZ L ’EMPLA CEMENT PRÉP AREZ LA HO TTE 1 Retirez le ruban adhésif qui sert à maintenir les filtres en place. Tirez sur les languettes des filtres et soulevez ces derniers. Mettez les filtres de côté.
Page 11 ALLURE ® WS2 SERIES RANGE HOOD HOTTE DE CUISINIÈRE DE LA SÉRIE ALLURE ® WS2 PRÉP AREZ LA HO TTE 4 Retirez l’une des deux ouvertures préamorcées du câble d’alimentation (sur le dessus de la hotte ou à l’arrière) et installez un serre-fils répondant aux normes régissant les installations électriques.
Page 12 ALLURE ® WS2 SERIES RANGE HOOD PRÉP AREZ LA HO TTE 1 3 Pour les installations avec un conduit d’évacuation d’air de 3¼ po x 10 po seulement : Retirez le ruban adhésif du registre et fixez le raccord de conduit sur l’ouverture choisie avec les vis que vous avez retirées lors de l’étape 4 de cette section.
Page 13 ALLURE ® WS2 SERIES RANGE HOOD INST ALLEZ LA HO TTE OUVERTURE EN FORME DE TROU DE SERRURE (4) VIS D’ASSEMBLAGE (4) 1 Utilisez les 4 vis d’assemblage (que vous retrouverez dans le sac contenant les pièces) pour suspendre la hotte.
Page 14 ALLURE ® WS2 SERIES RANGE HOOD A VERTISSEMENT : Afin de prévenir les risques d’électrocution, interrompez le courant avant de procéder à l’entretien de la hotte. Filtres d’aluminium : Nettoyez régulièrement à l’eau chaude avec un peu de détergent doux.
Page 15 ALLURE ® WS2 SERIES RANGE HOOD PIÈCES DE REMPLACEMENT N O DU N O DE SCHÉMA PIÈC E DESCRIPTION 2 R740013 Raccord de conduit avec registre (avec vis d’assemblage) 3 R602017 Vis n o 8-18 x .
Page 16 ALLURE ® WS2 SERIES RANGE HOOD 628004B GARANTIE GARANTIE LIMITÉE DE UN AN DE NUTONE NuTone garantit à l’acheteur consommateur original de ses produits qu’ils sont exempts de vice de matériaux ou de fabrication p our une période de un an à compter de la date d’achat original.
An important point after buying a device NuTone WS2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought NuTone WS2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data NuTone WS2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, NuTone WS2 you will learn all the available features of the product, as well as information on its operation. The information that you get NuTone WS2 will certainly help you make a decision on the purchase.
If you already are a holder of NuTone WS2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime NuTone WS2.
However, one of the most important roles played by the user manual is to help in solving problems with NuTone WS2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device NuTone WS2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
