Instruction/ maintenance manual of the product Q4 Series Nordyne
Go to page of 19
460 Volt Q4 Series Read these instructions thoroughly before starting the installation. Follow all precautions and warnings contained within these instructions and on the unit. These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances.
2 TABLE OF CONTENTS OWNER INFORMATION .......................................................................................................... 3 SPECIFICATIONS .........................................................................................
3 It is the sole responsibility of the homeowner to make certain that heat pump has been correctly set up and adjusted to operate properly. NORDYNE warrants the heat pump to be free from defects in material or workmanship for a period of one year. A warranty certificate with full details is included with the heat pump.
4 OPERATING INSTRUCTIONS To Operate Your Heat Pump For Cooling — 1. Set the thermostat system switch to COOL and the thermostat fan switch to AUTO. (See Figure 1) 2.
5 All models are shipped from the factory with the following: 1. Zero clearance to combustibles 2. Multi-speed direct-drive blower. 3. Blower Speed Relay. 4. Horizontal or Down flow duct connections. The unit dimensions are shown in Figure 3 . Optional field-installed electric heater kits are available in 9 kw and 15 kw heating capacities.
6 Figure 3. Dimensions 24.9 13.5 16.0 23.5 12.0 13.3 13.5 16.0 12.0 CG A 47.5 3/4" NPT Female Drain Connector B SUPPL Y RETURN Top View Side View Back View C en t e r o f G rav it y Hei g h t ( in in ch es) Mod el No. C w it h b ase rails w it h o u t b ase rails Q 4S A- 036 3 40 28.
7 Figure 4. Minimum Clearances 36" 36" 6" 72" 36" Condensate Drain Figure 5. Condensate Drain UNIT INSTALLATION Ground Level — When installing the unit at ground level, provide a concrete mounting pad separate from the building foundation.
8 Acoustical Duct Work — Certain installations may require the use of acoustical lining inside the supply duct work. Acoustical insulation must be in accordance with the current revision of the Sheet Metal and Air Conditioning Contractors National Association (SMACNA) application standard for duct liners.
9 Use a separate branch electrical circuit for this unit. A means of electrical disconnect must be located within sight of and readily accessibility to the unit. Internally mounted circuit breakers are available as field installed options. These circuit breakers can be used as an electrical disconnect.
10 interval settings are available: 30 minutes, 60 minutes, and 90 minutes. Time setting selection is dependent on the climate where the unit is being installed. Example 1. Dry climate of Southern Arizona. A 90 minute setting is recommended. Example 2.
11 UNIT MAINTENANCE ! W ARNING: To avoid risk of electrical shock, personal injury, or death, disconnect all electrical power to the unit before performing any maintenance or service. The unit may have more than one electrical supply. Refrigerant Charging — The Q4 packaged heat pumps are fully charged at the factory .
12 Typical Wiring (Field Supplied) for 1-Stage Cool, 1-Stage Heat Typical Wiring (Field Supplied) for 2-Stage Cool, 1-Stage Heat Figure 10. Typical Thermostat Connection E O G R Y1 1 2 3 4 5 6 7 8 9 B.
13 Heat Pump in Heating * Note: All pressures are listed in psig. and all temperatures in deg. F. — Shaded Boxes indicate flooded conditions — Rated Design Values. Suction Pressure will be lower than design value if indoor air flow, entering dry bulb, or entering wet bulb temperatures are lower than design.
14 Table 2a. Q4SA Heating Charging Charts Heat Pump in Heating * Note: All pressures are listed in psig. and all temperatures in deg. F. — Shaded Boxes indicate flooded conditions — Rated Design Values.
15 Q4S A-036 OU T D O O R T E M P E R AT URE ( ° F ) 70 75 80 85 90 95 100 105 Suc t. P res. Di sch . P res. Di sch . Te m p. Di sch . Pre s. Di sch . Te m p. Di sch . Pres . Di sch . Te m p. Di sch . P r es. Disch . Tem p . Di s c h . P r es. Di s c h .
16 Q4S A-060 OU T D O O R T E M P E R AT URE ( ° F ) 70 75 80 85 90 95 100 105 Suc t. P res. Di sch . P res. Di sch . Te m p. Di sch . Pre s. Di sch . Te m p. Di sch . Pres . Di sch . Te m p. Di sch . P r es. Disch . Tem p . Di s c h . P r es. Di s c h .
17 Q4 A C C E S S OR IE S Descri pti on P art N u m ber Roof Curb (8" ) 547830 Roof Curb (14" ) 547831 M anual F r es h A i r Damper 547832 E c onom i z er, downf l ow 547833 S uppl y/ ret u.
18 Convertible Packaged Heat Pump 460 V olt Three Phase 60Hz N N OTES: 1. Disconnect all power before servicing. 2. For supply connections use copper conductors only . 3. If any of the original wire as supplied with the furnace must be replaced, it must be replaced with wiring material having a temperature rating of at least 105 ° C.
INST ALLER: PLEASE LEA VE THESE INST ALLA TION INSTRUCTIONS WITH THE HOMEOWNER. R ® A S C O M P L Y I I T N G W H T T H N I S U I H A S B I D D A R I S T A N A R 2 1 0 T A I D N F I E D T R E C E E N R - C O I I O N I N G T A I D N R - C O I I O N I N G D I T I O N I N G N O C - R I A R ¢707885W¤ 707885A St.
An important point after buying a device Nordyne Q4 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Nordyne Q4 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Nordyne Q4 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Nordyne Q4 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Nordyne Q4 Series will certainly help you make a decision on the purchase.
If you already are a holder of Nordyne Q4 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Nordyne Q4 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Nordyne Q4 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Nordyne Q4 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
