Instruction/ maintenance manual of the product NI TB-2706 National Instruments
Go to page of 8
INSTALLATION GUIDE NI TB-2706 PXI/PXIe T erminal Block for M Series and NI 61 43 Devices This installation guide de scribes ho w to install and connect si gnals to the NI TB-2706 terminal block for use with PXI/PXIe M Series, NI PXI- 6143, a nd other PXI/PXIe de vices with a 68-pin VHDCI connector .
NI TB-2706 Installation Guide 2 ni.com ❑ 0.10 in. slotted scre wdriv er ❑ Pinout label for M Series (adhered to cov er of TB-2706) or pinout list for NI PXI-6143 ❑ Number 1 Phillips screwdri ver.
© National Instruments Corporation 3 NI TB-2706 Installation Guide Connecting the Signals Refer to Figure 1 as you complete the following st eps to connect signals to your terminal block. Figure 1. TB-2706 Part s Locator Diagram 1. Remov e the terminal block cover by unscre wi ng the top cov er scre w using the 0.
NI TB-2706 Installation Guide 4 ni.com Figure 2. Pinout Label for M Series Figure 3. Pinout for PXI-6143 2. Loosen or remove the strain -relief bar by loosening the two strain-relief screws with the Phillips-head scre wdri ver . 3. Use wire cutters and wire insu lation strippers to strip no more than 7 mm of insula tion from the wire ends.
© National Instruments Corporation 5 NI TB-2706 Installation Guide 6. T ighten or replace the strain-relief scre ws. 7. Replace the terminal block cover b y sliding the i ndentations on the co ver under the tabs on th e base. T ighten the top cover scre w .
NI TB-2706 Installation Guide 6 ni.com Specifications These specif ications are typical at 25 °C unless otherwise specified. Input/Output Caution The TB-2706 is not designed for input voltages greater than 42 V pk /60 VDC.
© National Instruments Corporation 7 NI TB-2706 Installation Guide CE Compliance This product meets the essential re quirements of applicable Europe an Dir ectives, as amended for CE marking, as foll.
National Instruments, NI, ni.com, and LabVIEW are tradem arks of National Instruments Corporation. Refer to t he Terms of Use section on ni.com/legal for m ore informat ion about Nationa l Instruments trademarks. Other product and compan y names mentioned herein are trademarks or trade names of their respective companie s.
An important point after buying a device National Instruments NI TB-2706 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought National Instruments NI TB-2706 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data National Instruments NI TB-2706 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, National Instruments NI TB-2706 you will learn all the available features of the product, as well as information on its operation. The information that you get National Instruments NI TB-2706 will certainly help you make a decision on the purchase.
If you already are a holder of National Instruments NI TB-2706, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime National Instruments NI TB-2706.
However, one of the most important roles played by the user manual is to help in solving problems with National Instruments NI TB-2706. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device National Instruments NI TB-2706 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
