Instruction/ maintenance manual of the product WS2C-50NF-X2 Moog Videolarm
Go to page of 16
PR ODUCT INSTR UCTIONS INST ALLA TION PREP ARA TION 1. Determine the mounting location. Be sure that you'll be mounting to a secure wall or ceiling. W e also recommend that for outdoor applications the housing be mounted in a protected area. 2. Complete all wire and conduit runs prior to installation.
- 2 - CAMERA BRA CKET SETUP (Figure 5) Reattach the brack et assembly to the back bo x using the two 10-32 x 3/8" screws . NO TE: For ceiling mount applications do not fully tighten immediately . Figure 2 1. Connect the output of your Class 2 P ower Supply to the terminal connectors on the PC Board inside the housing.
- 3 - Figure 6 CAMERA FOCUSING Fixed Lens: Loosen the set screw in the lens mount and to manually rotate the lens until a clear picture is achie ved. Once the focus is set, retighten the set scre w (Figure 6).
- 4 - The operational settings f or the camera are defi ned by ten dip switches located on the PC Board (Figure 9). Moving the switches to the on position will activate each setting. Factory defaults are pictured below (Figure 10 and 11). F A CT OR Y DEF A UL T FIXED AND FIXED V ARI-FOCAL LENSES: Dip Switches 5 and 7 on, all others off.
- 5 - NO TE: This hi-res color camera uses a 1/4" chip and a 3-6mm auto iris lens. It is comparable to a 1/3" chip using a 4-9mm auto iris lens. The operational settings are defi ned by f our dip switches located on the side of the PC Board (Figure 12 and 13).
- 6 - Wiring Notes Wire — What to DO 1. DO use point-to-point Unshielded T wisted P air wire, gauge 24 or thick er , stranded or solid, Categor y 2, 3, 4, or 5. 2. The video signal may co-e xist in the same wire bundle as other video , telephone, data, control signals , or low-v oltage power .
250 ft 250 ft 3 4 5 8 13 1 300 ft 300 ft 4 5 6 10 16 1 400 ft 400 ft 5 6 8 13 21 1 500 ft 500 ft 6 8 10 16 26 1 600 ft 600 ft 8 10 12 19 31 1 800 ft 800 ft 10 13 16 25 42 1 1 0 0 0 f t 13 16 20 32 52 .
! CAUTION RISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE. SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read befor e the unit is operated.
P ower Supply P ower A P ower B Camera Assembly Primar y Po w e r Video Signal Video Shield Monitor - 10 - (Ground Return) Figure A Ground Loop TR OUBLESHOO TING If you e xper ience problems with the camera picture please chec k these simple troubleshooting procedures f or possible solutions before calling technical suppor t.
AC V oltmeter Camera Monitor Bridge Tap NV-213 A NV-213 A - 11 - NVT TROUBLESHOO TING If you are e xper iencing problems , attempt to simplify your setup . T est each cable segment separately . F or example , test the camera and monitor together without the other equipment.
- 12 - Depending on the voltage being used, ref er to one of the formulas below to select the correct pow er supply for camer as connected in parallel (positive to positiv e, negative to negativ e): T.
6 5 4 3 2 1 7 - 13 - WS2 - Exploded Diagram.
- 14 - WS2 - Replacement P ar ts List Part Number Description 1 RPWS2010 W ARRIOR 2 & 4 BASE ASSEMBL Y 2 RPWS2020 W ARRIOR 2 & 4 CARRIAGE ASSEMBL Y KIT NTSC BOARD CAMERAS 3 RPWS1041F W ARRIOR .
7 6 5 4 3 2 1 - 15 - WS4 - Exploded Diagram.
- 16 - WS4 - Replacement P ar ts List Part Number Description 1 RPWS2010 W ARRIOR 2 & 4 BASE ASSEMBL Y 2 RPWS2020 W ARRIOR 2 & 4 CARRIAGE ASSEMBL Y KIT NTSC BOARD CAMERAS 3 RPWS3041F W ARRIOR .
Pr oduct Registr ation / W arr anty Thank y ou f or choosing Videolarm. W e value y our patr onage and ar e solely committ ed to pr oviding y ou with only the highest quality pr oducts av ailable with unmatched customer service lev els that ar e second-t o-none in the security industr y .
An important point after buying a device Moog Videolarm WS2C-50NF-X2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Moog Videolarm WS2C-50NF-X2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Moog Videolarm WS2C-50NF-X2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Moog Videolarm WS2C-50NF-X2 you will learn all the available features of the product, as well as information on its operation. The information that you get Moog Videolarm WS2C-50NF-X2 will certainly help you make a decision on the purchase.
If you already are a holder of Moog Videolarm WS2C-50NF-X2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Moog Videolarm WS2C-50NF-X2.
However, one of the most important roles played by the user manual is to help in solving problems with Moog Videolarm WS2C-50NF-X2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Moog Videolarm WS2C-50NF-X2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
