Instruction/ maintenance manual of the product XEQ ARC Audio
Go to page of 10
XEQ MANU AL AND USER GUIDE 3-W A Y CR OSSO VER WITH SUB SONIC FIL TER 7-BAND EQU ALIZER WITH DIRECT SUB INPUT IDX V ariable Sub Phase Shift Sub Sonic Filter Fully V ariable Band Pass Crossover 8 V olt.
Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio's lengthy experience in performance car audio design combined with our highly skilled engineering staff. Y ou are now the proud owner of the IDX or XEQ .
Installation Information 1. The XEQ needs to be installed in the signal path between your source unit and your external amplifier(s). 2. Physically mount the XEQ near the drivers listening position.
1. Front Output: Simply connect to the amplifier driving the front speakers. This is a full range output so if you plan to run it hard you should use a crossover at this point. 2. Rear Output: Just like it sounds, this is connected to the rear amp. 3.
XEQ Optional 2-W A Y With F ADING FRONT and REAR 7 XEQ Signal to Noise Ratio (A-W eighted) >100dB THD @ 8.0V Output 0.005% Channel Separation >75dB Sub W oofer Crossov er 45Hz-150Hz 12dB/Octav e Input Impedance 15K Ohms RMS Output @ 1KHz 9.0 V olts F requency Response 20Hz-30KHz EQ F requency Range @ 50Hz 100Hz 275Hz 770Hz 2.
Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio's lengthy experience in performance car audio design combined with our highly skilled engineering staff. Y ou are now the proud owner of the IDX or XEQ .
Installation Information 1. The IDX needs to be installed in the signal path between your source unit and your external amplifier (s). 2. Because of it's small size the IDX can be mounted almost anywhere. The chassis is designed to fit a 1/2 DIN opening.
1. Front Input: This is the default input. If you are using one input (2 CH.) connect your RCAs here. 2. Rear Input: Use the rear inputs for 4-channel operation. In this configuration you can have faded front and rear front your hear unit. 3. Front Output: Front output in name only .
X10 OFF 90Hz X 1 = 90Hz X10 OFF 90Hz X 1 = 90Hz 2-W A Y F ADING FRONT AND REAR NO TE: THE CONTR OL POSITIONS SHOWN ARE ONL Y ONE SUGGESTED CONFIGURA TION.
X10 OFF 500Hz X1 = 500Hz X10 OFF 90Hz X 1 = 90Hz X10 OFF 500Hz X 1 = 500Hz IN BAND P ASS MODE 90Hz TO 5000Hz 3-W A Y WITH ACTIVE FIL TERING FOR MID-BASS AND COMPONENT SET NO TE: THE CONTR OL POSITIONS SHOWN ARE ONL Y ONE SUGGESTED CONFIGURA TION. Y OUR SYSTEM MA Y REQUIRE DEFERENT SETTINGS.
An important point after buying a device ARC Audio XEQ (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ARC Audio XEQ yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ARC Audio XEQ - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ARC Audio XEQ you will learn all the available features of the product, as well as information on its operation. The information that you get ARC Audio XEQ will certainly help you make a decision on the purchase.
If you already are a holder of ARC Audio XEQ, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ARC Audio XEQ.
However, one of the most important roles played by the user manual is to help in solving problems with ARC Audio XEQ. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ARC Audio XEQ along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
