Instruction/ maintenance manual of the product DXE ARC Audio
Go to page of 20
DXE DIGITAL HYBRID EQ/CROSSOVER FULLY BALANCED SIGNAL FROM HEAD UNIT TO CONTROL UNIT. GREEN DOT MATRIX DISPLAY REMOTE CONTROLLER. DUAL INPUT. 5 BAND PARAMETRIC EQ. MICROPROCESSOR CONTROLLED. 12/24 DB HIGH PASS CROSSOVER. 3 STEREO PLUS SUMMED SUB AND CENTER OUTPUTS.
DXE Manual Table of Contents Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio’s lengthy experience in performance car audio design combined with the legendary engineering skills of Robert Zeff and the staff at Nikola Engineering.
10.
11.
Configuration and T uning High Pass Crossover 12dB/24dB pre octave. 16Hz – 7100Hz 12dB/24dB Per Octave Stereo Crossover Frequency Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Frequency Menu .
Crossover 3 (X3) High Pass = 167Hz -7100Hz Low Pass = 167Hz -7011Hz Band Pass High=167Hz -7100Hz Band Pass Low= 16Hz -710Hz 12dB per Octave Crossover Mode Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Range Menu .
Crossover 2 (X2) High Pass = 115Hz -4900Hz Low Pass = 115Hz -4900Hz Band Pass Low= 16Hz -710Hz Band Pass High=115Hz -4900Hz 12dB per Octave Crossover Mode; Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Range Menu .
The DXE Menus Sub Crossover 12dB/24dB/48dB mono 4Hz – 152Hz Crossover Frequency Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Frequency Menu . Tap the Select button until you reach the Sub: (Subwoofer) Frequency .
To Change the Presets, The DXE has six memory presets. With six different system configurations, almost anything is possible. Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Presets menu. Turn the knob either direction to select the Preset you wish.
The DXE Menus 1: Freq Menu 1: Sub: 65.4 Hz 2: X2 HP 0115 Hz 3: X2 (HP) 4: X3 Hi: 3508 Hz 5: X3 Low: 0075 Hz 6: HP: 3508 Hz RH 2: Gain Menu X2 Level: -04dB X3 Level: -00dB Ctr level: -90dB Sub Level: +.
Specifications Max input level 8 volts RMS Input sensitivity 8V (0 dB), 2V (10 dB), 700mV(20 dB) Max output level 10 volts RMS Input impedance 47.5 K ohm Minimum output impedance 600 ohms Harmonic distortion + Noise < .
LIMITED WARRANTY Before shipping this product back for service call for a Return Authorization number. This number must be clearly marked on the outside of the box.
Features: 1. Fully balanced signal from EQ unit to Crossover. 2. Green dot matrix display remote controller for setting output levels, crossover range and configuration of control unit. 3. Front- Rear fader. 4. Back lit knobs (Blue). 5. Dual input. 6.
INSTALLATION INFORMATION 1. The DXE needs to be installed in the signal path between your source unit and your external amplifier(s). 2. Physically mount the DXE in a location that keeps it clean, cool, and dry. Don’t mount it under a cup holder or in a storage box were it will be covered with the stuff that always seems to collect in our cars.
The Connections and Controls The Front Panel 5. Master Volume Level Control: DXE has the ability to control the volume of your system including both inputs.
Back Panel 1. Inputs: The DX E has two RCA inputs that need to get their audio signals from the source units (CD Player and Video system). If your source unit has multiple outputs (like a front, rear, and/or subwoofer) you should only connect the front or rear outputs to your DXE.
The Crossover Display 1. The Plug: This is a 10-pin flat wire cable. Do Not mista ke it for the 8 pin Balanced Line cable. It won’t work. 2. The Knob : This is a rotary encoder. All adjustments to the crossover are made here. It doesn’t have a stop.
DXE Crossover 1. Balanced Input : This balanced line connector should be connected to the DXE Equalizer, Be careful to plug it into the right spot. This cable will plug into the remote display port but this is a bad thing. Don’t try it. 2. Power Out : This powers the EQ Section.
8.
9.
An important point after buying a device ARC Audio DXE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ARC Audio DXE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ARC Audio DXE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ARC Audio DXE you will learn all the available features of the product, as well as information on its operation. The information that you get ARC Audio DXE will certainly help you make a decision on the purchase.
If you already are a holder of ARC Audio DXE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ARC Audio DXE.
However, one of the most important roles played by the user manual is to help in solving problems with ARC Audio DXE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ARC Audio DXE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
