Instruction/ maintenance manual of the product xps336ir V.34/V.42bis MaxTech
Go to page of 23
Part #MAN080 Rev. 1.0 S F-1128HV/R16-PnP High Performance V .34/V .42bis 28,800 BPS Internal Plug and Play F AX/V oice/Data Modem Featuring Advanced Full- Duplex Speakerphone Functions User's Man.
Contents Section One - Introduction ................................. 1 Section T wo - Installation .................................. 1 Section Three - A T Command Set .................... 7 Section Four - S Registers .............................. 13 Section Five - Result Codes .
1 Section One - Introduction This 28.8 Kbps Plug and Play FAX/Voice/Data Speakerphone Modem connects your computer to all popular high speed modems available today.
2 or, 2. If running DOS or Windows 3.x, configure the modem using the included modem driver. Instructions for installing this driver are included in the text file called README.1ST on the Windows 95 driver disk. The README.1ST file can be viewed by loading it into any wordprocessor or any text editor (i.
3 6. Replace the computer cover and plug in your com- puter. 7. Connect the telephone cable from the modem's LINE connector to the telephone wall jack. See Figure 2-2. 8. Optionally, connect your telephone to the modem's PHONE connector. 9. Optionally, connect your microphone to the modem's MIC jack.
4 The Install From Disk dialog box now instructs you to “Insert the manufacturer's installation disk into the drive selected, and then click OK.” Insert the modem's Utility diskette into the disk drive and type A: (or B: if inserted in drive B) in the “Copy manufacturer's files from:” box.
5 MANAGER|MAIN|CONTROL PANEL , click on PORTS and follow Windows 3.1x user's manual instructions on configuring the installed modem COM port. Proceed to Section 2.5, Software Installation/Con- figuration. 2. 5 Software Installation and Configuration You are now ready to install and configure the communication software.
6 2. 7 Testing Your Modem After Installation In order to test your modem you should be familiar with your communication software. Load and set up your communication software and enter into “terminal mode.” Make sure that the COM Port and IRQ settings of the modem match the software.
7 Section Three - AT Command Set 3. 1 Executing Commands Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands may be sent to your modem from a PC running communication software or any other terminal devices.
8 , pause @ wait for five seconds of silence ! flash ; return to Command Mode after dialing DS=n Dial one of the four telephone numbers (n=0-3) stored in the modem’s non-volatile memory.
9 W _ W 0 Report DTE speed only W 1 Report line speed, error correction protocol, and DTE speed. W 2 Report DCE speed only X _ X 0 Hayes Smartmodem 300 compatible responses/blind dialing.
10 ratio &P 2 Same as &P0 setting but at 20 pulses per minute &P 3 Same as &P1 setting but at 20 pulses per minute &R_ &R 0 Reserved & R 1 CTS operates per flow control req.
11 d =300-28800. A, b, c, d default=11, 1, 300, 28800. Parameter “ a ” specifies the modulation protocol desired where: 0=V.21, 1=V.22, 2=V.22bis, 3=V.23, 9=V.32, 10=V.32bis, 11=V.34, 64=Bell 103, 69=Bell 212, and 74=VFC. Parameter “ b ” specifies automode operations where: 0=automode disabled, 1= automode enabled with V.
12 N 2 V.42 or MNP data link only N 3 V.42/MNP/Normal data link N 4 V.42 data link only N 5 MNP data link only 3. 6 Fax Class 1 Commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Rec.
13 +FPTS: Page Transfer Status +FPTS= Page Transfer Status +FREV? Identify Revision +FSPL Enable polling +FTSI: Report the Transmit Station ID 3. 8 Voice Commands #BDR Select Baud Rate #CID Enable Cal.
14 Table 4-1 S - Registers Register Function Range/units Default S0 Auto-answer Ring 0-255 /rings 0 S1 Ring counter 0-255 /rings 0 S2 Escape code character 0-127 /ASCII 43 S3 Carriage return character.
15 S49-81 Reserved S82 Break options 3, 7, or 128 1 28 S83-85 Reserved S86 Connection failure code 0, 4, 5, 9, 12, 13, 14 * S87-S90 Reserved S91 Transmit attenuation 0-15/dBm 10 S92 Fax attenuation 0-.
16 receive data from the modem. 2. Make sure that your modem is initialized correctly. Your modem may have been initialized to not display re- sponses. You may factory-reset the modem by issuing AT&F and press ENTER . The factory default allows the modem to display responses after a command has been executed.
17 communication software. 3 . Make sure the data speed is not faster than your computer's capability. Most IBM compatibles are ca- pable of 19,200 bps under DOS and Windows. Operat- ing at higher speeds under Windows requires a faster CPU (386/486 or better), a high performance replace- ment Windows 3.
18 Data format: 300-115200 bps Power: 0.75 W Temperature: 0 to 5 5 degrees C (Operating) Caller ID: Y e s PnP: Revision 1.0a Speakerphone: Full-duplex with DSP echo cancellation Appendix B - Speaker Type Selection Your modem supports both mono and stereo speakers.
19 The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)). FCC Class B Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
20 company cause to request the user to disconnect the equip- ment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.
21.
An important point after buying a device MaxTech xps336ir V.34/V.42bis (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MaxTech xps336ir V.34/V.42bis yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MaxTech xps336ir V.34/V.42bis - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MaxTech xps336ir V.34/V.42bis you will learn all the available features of the product, as well as information on its operation. The information that you get MaxTech xps336ir V.34/V.42bis will certainly help you make a decision on the purchase.
If you already are a holder of MaxTech xps336ir V.34/V.42bis, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MaxTech xps336ir V.34/V.42bis.
However, one of the most important roles played by the user manual is to help in solving problems with MaxTech xps336ir V.34/V.42bis. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MaxTech xps336ir V.34/V.42bis along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
