Instruction/ maintenance manual of the product V.34+ MaxTech
Go to page of 21
Part #MAN117 Rev. 1.0 K56Plus/HIS-FM High Performance K56Plus/V.34+/V.42bis 56K BPS Plug & Play Internal FAX/Data Modem User's Manual Contents Section One - Introduction .......................... 1 Section Two - Installation ................
The information contained in this manual has been validated at the time of this manual's production. The manufacturer reserves the right to make any changes and improvements in the product de- scribed in this manual at any time and without notice.
1 Section One - Introduction This 56 Kbps* Plug and Play FAX/Data Modem connects your computer to all popular high speed modems available today. The modem incorporates “K56Plus” (56Kbps) technology to provide increased download speeds using regular telephone lines.
2 Proceed to Section 2.3 now if you have every- thing required. If you have neither 2A or 2B above, you have two options to provide Plug and Play functionality to your PC. 1. Install Windows 95 or, 2. If running DOS or Windows 3.x, configure the modem using the included modem driver.
3 4. Carefully slide the internal modem into the slot you have chosen, applying even pressure until the modem is completely seated in the slot. 5. Fasten the retaining bracket with the screw from the slot cover. Make sure the modem is properly aligned.
4 • Section 2.4.1.1 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the New Hardware Found dialog box • Section 2.4.1.2 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the Update Device Driver Wizard .
5 2.4.2 Configuring in a Plug and Play System with- out Windows 95 When this modem is installed in a Plug and Play system without Windows 95, the computer's BIOS will assign a COM port and IRQ line to the modem. Proceed to Section 2.5, Software Installation/ Configuration.
6 Note that your software must be configured to communicate with the modem on the same COM port and IRQ line used by the modem. 2.6 Testing Your Modem After Installation In order to test your modem you should be familiar with your communication software.
7 contain reference material, and can be skipped. If you have difficulties getting your modem to work, read Section 6 - Troubleshooting to find answers to com- monly asked questions and problems. Section Three - AT Command Set 3.1 Executing Commands Commands are accepted by the modem while it is in Command Mode.
8 D _ 0 - 9, A-D, # and * L last number redial P pulse dialing T touch-tone dialing W wait for second dial tone , pause @ wait for five seconds of silence ! flash ; return to Command Mode after dialing DS=n Dial one of the four telephone numbers (n=0-3) stored in the modem’s non- volatile memory.
9 Sr=n Set register r to value n (n = 0-255). T Set Tone Dial as default V_ V0 Numeric responses V1 Word responses W_ W0 Report DTE speed only W 1 Report line speed, error correction protocol, and DTE speed. W2 Report DCE speed only X _ X0 Hayes Smartmodem 300 compatible responses/blind dialing.
10 &K5 Enable transparent XON/XOFF flow control &K6 Enable both RTS/CTS and XON/XOFF flow control &L_ &L0 Modem is set up for dial-up operation &M_ &M0 Asynchronous operation &.
11 %E_ %E 0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,d.e,f Select modulation where: a =0, 1, 2, 3, 9, 10, 11, 56, 64, 69; b =0-1; c =300- 56000; d =300-56000; e =0-1; and f =0- 1.
12 &Q_ &Q0 Direct data link only (same as N1) &Q5 V.42 data link with fallback options &Q6 Normal data link only (same as N0) A_ A0 64-character maximum MNP block size A1 128-character.
13 Table 4-1 S - Registers Register Function Range/units Default S0 Auto-answer Ring 0-255 /rings 0 S1 Ring counter 0-255 /rings 0 S2 Escape code character 0-127 /ASCII 43 S3 Carriage return character.
14 S49-81 Reserved S82 Break options 3, 7, or 128 1 28 S83-85 Reserved S86 Connection failure code 0, 4, 5, 9, 12, 13, 14 S87-S90 Reserved S91 Transmit attenuation 0-15/dBm 10 S92 Fax attenuation 0-15.
15 Section Six - Troubleshooting This section describes some of the common problems you may encounter while using your modem. If you can not resolve your difficulty after reading this chapter, contact your dealer or vendor for assistance. Modem does not respond to commands.
16 used. 2. Make sure the correct terminal emulation mode is being used (see communication software manual). High pitch tone is heard whenever you answer the phone. 1. Make sure Auto-Answer is turned off. Your modem is factory configured to NOT auto-answer.
17 Appendix A - Specifications Communication Std. K56FLEX (56Kbps), V.34, V.32bis, V.32, V.29, V.27ter, V.22bis, V.23, V.22, V.21, V.17, Bell212/103 Data Compression: V.
18 The FCC prohibits this equipment to be connected to party lines or coin-telephone service. In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or ven- dor.
19 permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
An important point after buying a device MaxTech V.34+ (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought MaxTech V.34+ yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data MaxTech V.34+ - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, MaxTech V.34+ you will learn all the available features of the product, as well as information on its operation. The information that you get MaxTech V.34+ will certainly help you make a decision on the purchase.
If you already are a holder of MaxTech V.34+, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime MaxTech V.34+.
However, one of the most important roles played by the user manual is to help in solving problems with MaxTech V.34+. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device MaxTech V.34+ along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
