Instruction/ maintenance manual of the product BJN161 (LXNJ01*1) Makita
Go to page of 8
PRODUCT P 1/ 8 Model No. Description C ONCEPT AND MAIN APPLICATIONS BJN160/ BJN161 (LXNJ01 * 1 ) 1.6mm (16Ga) Cordless Nibbler S pecification S tandard equipment O ptional accessories Punch Die Battery BL1430 for Model BJN160 Battery BL1830 for Model BJN161 (LXNJ01 * 1 ) Note: The standard equipment for the tool shown above may vary by country.
R epair Apply Makita grease F A No.2 to the following portions designated with the black triangle to protect parts and product from unusual abrasion. [3] DISASSEMBL Y/ASSEMBL Y [3] -1. Gear housing complete [1] NECESSAR Y REP AIRING T OOLS CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.
P 3 / 8 R epair [3] DISASSEMBL Y/ASSEMBL Y [3] -1. Gear Housing Complete (cont.) DISASSEMBLING (2) Disassemble the component parts from Gear housing complete as drawn in Fig. 3 . 1. Remove Stopper by unscrewing Bind CT4x12 Tapping screw. Stopper Bind CT4x12 Tapping screw Die holder section 2.
R epair DISASSEMBLING ASSEMBLING (3) Disassemble Spur gear 31 and Crank section as drawn in Fig. 4 . (1) Assemble Spur gear 31 and Crank section as drawn in Fig. 5 . (2) Assemble Spur gear 31, Crank section and the other component parts to Gear housing complete by reversing the disassembly procedure.
[3] DISASSEMBL Y/ASSEMBL Y [3] -2. Armature [3] -3. Y oke unit DISASSEMBLING ASSEMBLING (3) Disassemble Carbon brushes and Armature as drawn in Fig. 6 . Fig. 6 Fig. 7 1. Remove Holder cap cover by levering it up with a slotted screwdriver. 3. Separate Gear housing complete from Housing set by unscrewing four 4x20 Tapping screws.
[3] DISASSEMBL Y/ASSEMBL Y [3] -4. Die and Punch DISASSEMBLING Fig. 8 Fig. 9 Die holder 1 Pull off Die holder from Gear housing complete. 2 Remove Punch by loosening M5x8 Hex socket set screw with Hex wrench. 3 Remove Die from Die holder by unscrewing two M3x12 Hex socket head screws.
C ircuit diagram W iring diagram Color index of lead wires' sheath Black Red LED Circuit Set Endbell complete on Housing L as follows: * Face its Lead wires to the belly side of Housing L. * Face Lead wire (black) to Housing L. Setting Endbell Complete on Housing L Fig.
W iring diagram Wiring to Switch Wiring in Housing L Switch button Set Switch to Housing L as follows: * Face Switch button to Controller side. * Face Insulated terminals connected side (See Fig.
An important point after buying a device Makita BJN161 (LXNJ01*1) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita BJN161 (LXNJ01*1) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita BJN161 (LXNJ01*1) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita BJN161 (LXNJ01*1) you will learn all the available features of the product, as well as information on its operation. The information that you get Makita BJN161 (LXNJ01*1) will certainly help you make a decision on the purchase.
If you already are a holder of Makita BJN161 (LXNJ01*1), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita BJN161 (LXNJ01*1).
However, one of the most important roles played by the user manual is to help in solving problems with Makita BJN161 (LXNJ01*1). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita BJN161 (LXNJ01*1) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
