Instruction/ maintenance manual of the product LC-7314 Approach Tech
Go to page of 106
Before trying to connect or operate this product, please read this manual completely INST ALLA TION & OPERA TI ON MANU AL IP CAMERA LC-7 314 ( PAL ).
.
1 Table Of Contents SAFETY PRECAUTIONS ............................................................................. 3 1. PRODUCT FEATURES............................................................................. 4 1.1 P RODUCT I NSTRUCTIONS ......
2 4.6 C ONNECTION T ESTING ....................................................................... 23 5. Operating Instructions for Image Software and Network .................. 25 5.1 M ICROSOFT I NTERNET E XPLORER ...................................
3 SAFETY PRECAUTIONS All the following safety and operational instructions to prevent ha rm or injury to the operator (s) or other persons should be read carefully before the unit is activated. W ARNING T o prevent fire or shock hazard, avoid ex posing this unit to rain or moisture.
4 1. PRODUCT FEA TURES 1.1 Product Instructions The newly designed H.264 / MJ PEG stream IP camera provides simultaneous video codec streams of H.264 and MJPEG in 520 TV lines. This IP camera not on ly supports the 25 fps frame rate, motion detection and built-in microphone, but also the day and night, and pre- and post-alarm functions.
5 Video Codec: Video compression: H.264 Motion JPEG Resolutions: 720 x 576 (P AL) 352 x 28 8 (P AL) Video streaming: Simultaneous H.264(720 x 480 and 352 x240) Video Codec – MJPEG: Motion JPEG frame rate: Up to 25 fps at 720 x 576 (P AL) Motion JPEG rate control: Y es Motion JPEG quality level: 5 Video Codec – H.
6 Network active alarm notification: Y es (ANNP ) Hardware: Processors: T exas Instruments DaV inci High performance 32-bit RISC CPU DDRII memory: DDRII 1Gbit Flash memory: 256Mb Real-time clock: Buil.
7 File system: F A T32/16/1 2 Recording format: JPG/A VI Network play- back: Y es SD card brand verified: A-Data/ PQI/ T oshiba/ T ranscend/ APacer/ Photo Fast Device Indicator: Ethernet Link: Y es Et.
8 2. DESCRIPTION OF THE FRONT/RE AR VIEW 2.1 Front Panel and Re ar Panel -- Front Panel -- -- Rear Panel -- 1 2 SD / SDHC ETHERNET (PoE) AC 24V DC 12V VIDEO USB 11 2 RESET 6 ! 34 5 6 7 8 91 0 1 1 1. MICROPHONE: The IP Camera has an additional audio function.
9 2.2 ALARM I/O 1.ALM - OUT A 2.ALM - OUT B 3.ALM -IN + 4.ALM-IN - 5.ALM - RST + 6.ALM - RST - 7. RS-485: D+ 8. RS-485: D- 9.DC - OUT( 5V) 10.G ND 11.AU DIO- I N 12.AU DIO- OUT 1 & 2. AL ARM OUT (OUTPUT): This is an alarm output trigger . Connect this to external devices such as buzzers or lights.
10 2.3 Flank Panel IRIS 1. AES 2. DC IR IS 3. DH CP 4. ST A TIC IP 1 2 3 4 1.ALM -OUT A 2.ALM -OUT B 3.ALM -IN + 4.ALM-I N - 5.ALM -RST + 6.ALM -RST - 7.RS-4 85:D+ 8.RS-4 85:D- 9.DC -OUT( 5V) 10.GN D 11. AUDIO- I N 12. AUDIO- OUT 1 2 1. IRIS: Auto iris connector.
11 2.4 The USB function By connecting the IP Camera with a PC via the USB connector , the IP Camera can provide two different functions. 1. Insert an SD card: As a card reader . Insert an SD card into the IP Camera, then connect t o the PC. Y ou might transfer files between the SD card and the PC.
12 3. INST ALLA TION Please follow the instructions and the diagram below to set up the system. NOTE: The IP C amera is linked by its Video Out connection via a B NC connector to a monitor's Video In connection.
13 3.3 CONNECTING WITH A M UL TIPLEXER LAN CAMERA 1 LAN CAMERA 2 LAN CAMERA 16 TO LAN CAMERA VIDEO OUT BNC CONNECTOR 3.4 UPDA TING SYSTEM SOFTWA RE If the system software of the IP Camera needs to be upgraded, please take the following steps to safely process it.
14 9. If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET PLEASE", please write down the error mess ages shown on the screen and inform your technical support, while ignoring the following steps.
15 3.5 IP Camera SD car d Troubleshooting 1. Check if the SD card position is correct or not. Please refer to the manual for the re lated information. 2. After powering the IP Camera on, correctly insert the SD card, and a little icon of "SD" will show up in the upper-right corne r of the monitor screen.
16 4. Network Configuration 4.1 Cable Connection s Please follow the instructions below to connect yo ur IP Camera to a computer or a network and to choose a proper RJ-45 cabl e configuration for c onnections. Physical specifications of the R J-45 cable for Ethernet Wire T ype Cat.
17 4.1.2 Connect to a LAN Hub (I NTRANET) The RJ-45 PIN configuration for connec ting with a LAN Hub is shown below . RJ-45 LAN CAMERA TO PC NETWORK CARD uplink.
18 4.2 Configure Y our IP Camera Net work Settings Upon connecting with the network hardware, you need to activate the net work function and configure the proper network settings of the IP Camera. 4.2.1 Enable DHCP Function This function can onl y work if the LAN, which t he unit is connected to, has a DHCP server .
19 NOTE: When connecti ng to a network, each connecte d IP Camera must be assigned a unique IP , which must be in the same cla ss type as your netw ork address. IP addresses are written as four sets of numbers sep arated by periods; for example, 192.168.
20 4.3 TCP/IP Communication Sof tw are Follow the procedure below to install the TCP /IP communication program in y our computer . Click the Start menu from your computer , and point to the Settings/Control Panel. Double click the Network icon to enter the windows.
21 Click the Configuration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is included, please pr oc ess section 4.5. If it is not includ ed, please follow section 4.4 to install the TCP/IP . 4.4 TCP/IP Ins t allation During the installation, you will be requested to insert the Windows CD-ROM.
22 4.5 TCP/IP configuration setting Click Sta r t → Settings → Control Panel → Networ k . Select TCP/IP , and then click Properties . Before processing the IP Camera installation in a W AN, please make sure the Internet connection works properly .
23 4.6 Connection T esting With the previous settings, follow the instructi ons below to ensure whether you have established the connection successfully . Click Start → Programs → MS-DOS Prompt T ype in ping 192 .168.1.168, then enter . (See the sample screen below).
24 If you receive a response as in the sa mple screen below , the conn ection hasn’t been successfully est ablished. Please re-check all the hardware and software installations by repeating steps 1 to 5. If you still can’t establis h the connection after rec hecking, please contact your dealer .
25 5. Operating Instructions for Image Sof tw are and Net work T wo choices of software are available for linking with the IP Camera: (1) the Microsoft Internet Explorer; and (2) the IP Camera VIEWER, a network browser in a PC which provides the functions of monitoring remote zones or watc hing recorded data through the TCP/IP protocol.
26 5.1 Microsof t Internet Explorer 5.1.1 Connecting the IP Camera 1. S tart up the Microsoft Internet Explorer , and then follow the steps below to connect the IP Camera. 2. Click the URL block at the top of the window . 3. Enter the URL address of the IP Camera into the URL block and press the “ Enter ” button to enter the home page.
27 Browsing images from th e IP Camera The images from the IP Camera will be displayed on the home p age while going online with the IP Camera. Some buttons of the home page are provided for further setting. In MJPEG mode or in H.264 mode, there are different display formats of its home p age.
28 5.1.2 Change Image Setti ng Please follow the steps below to change the image setting through the network if necessary . 1. Click the Image button on the home page to enter the image-setting page. 2. Adjust the image setting including “Devic e T itle” and “Viewer T ype” if necessary .
29 5. Click the H.264 Image button to e nter the H.264 image-setting page. Adjust the image setting including “Resolution”, “Quality” and “Frame Rate” if necessary .
30 8. Click the Privacy Mask button to enter the Privacy Mask page. 9. Click the Day & Night button to enter the Da y & Night page. Click the drop-down list to choose the Day & Night mode of “Auto”, “Day mode”, “Night mode” and “Schedule”.
31 10. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes instant ly . (If the setting has not been changed by the above steps, any (re)entry onto the home page w ill find images in their earlier or original setting.
32 5.1.3 Change the Netw ork Setting Please follow the steps below to change the network setting through the network if necessary . Set the network options and IP address. 1. Click the Network button in the home page to enter the Net work page. 2.
33 Description of function ke ys: IP A ddress: Enter the 4-byte IP Address in the appropriate blank space (the value in each box may be anywhere bet ween 0 and 255). Every IP camera has to own an IP address to be identified on the network. Netmask: Fill in the 4-byte Subnet Mask in the r equired blank spaces (usually any numbers between 0 and 255).
34 Change the Network Setting — FTP . Please follow the steps below to change the FTP setting via the netw ork if necessary to upload recording data live.
35 Change the Network Setting — SMTP . Please follow the steps below to change the SMTP setting through the network if necessary . 1. Click the SMTP button at upper left above to enter the “SMTP Server Setting” page. 2. Click “My Server Requires Authentication” to c heckmark the attached box and activate the function.
36 Change the Network Setting — SNTP . Please follow the steps below to change the SNTP setting through the network if necessary . 1. Click the SNTP button at upper left above to enter the “SNTP Server Setting” page. 2. Enter the IP Address of the SNTP server , and choose one of the time zones as and when necessary .
37 Change the Network Setting — DDNS. The “Network” page has, on its upper left, the “DDNS” icon. Please follow the step s below to change the DDNS setting through the network if necessary . 1. Click the DDNS button at upper left above to enter the “DDNS Setting” page.
38 Description of function ke ys: Enable DDNS Function: Checkmark to activate the function. DDNS T ype: Click to open the list of two DDNS modes to choose from: “D ynDNS” and “hn”. Click the “Apply” button and connect this website automatic ally and enter it.
39 Change the Network Setting — PPPoE. The “Network” page has, on its upper left, the “PPPoE” icon. Please follow the steps below to change the PPPoE setting through the network if necessary . 1. Click the PPPoE button at upper left above to enter the “PPPoE Setting” page.
40 Change the Network Setting —UPnP . The “Network” page has, on its upper left, the “UPnP” icon. Please follow the step s below to change the UPnP setting through the network if necessary . 1. Click the UPnP button at upper left above to enter the “Universal Plug and Play” page.
41 Change the Network Setting — IP Filter The “Network” page has, on its upper left, the “IP Filter” icon. Please follow the step s below to change the IP Filter setting through the network if necessary . 1. Click the IP Filter button at upper left above to enter the “Network Setting” page.
42 Change the Network Setting —Network T raffic. The “Network” page has, on its upper left, the “T ra ffic ” icon. Please follow the step s below to change the UPnP setting through the network if necessary . 1. Click the Traffic button at upper left above to enter the “Network T raffic” page.
43 5.1.4 Change the System S etting Please follow the steps below to change the date and time of the system setting through the network if necessary . Set the Date and Time of the system 1. Click the Syst em button in the home page to enter the “Date And T ime” page (default).
44 Change the System Setting — Timest amp. Please follow the steps below to change/add the timestamp through the network if necessary . 1. Click the Timest amp button on the left side of the “System - Date and T ime” page to enter the “T imestamp” page.
45 Change the System Setting — Users. Please follow the steps below to change/add the users’ authority through the network if necessary . 1. Click the Users button on the left side of the “Date and T ime” page to enter the “Use rs” page.
46 Change the System Setting — Digital I/O. Please follow the steps below to change the Digit al I/O through the net work if necessary . 1. Click the Digital I /O button on the left side of the “Date and T i me” page to enter the “Digital I/O Setting” page.
47 Change the System Setting — Audio Me chanism. Please follow the steps below to change the Audi o Mechanism through the network if necessary . 1. Click the Audio Mechanism button on the left side of the “Dat e and Time” p age to enter the “Audio Mechanism Setting” page.
48 Change the System Setting — RS485 Setting. Click the RS485 Setting button on the left side of the “Date and T ime” page to enter the “RS485 Setting” page.
49 Change the System Setting — Update Firmware. Please follow the steps below to change the Audi o Mechanism through the network if necessary . 1. Click the Update Firmware button on the left side of the “Date and T ime” page to enter the “Update Firmware” page.
50 View the Event Logs. Please follow the steps below to view event s through the network if necessary . 1. Click the Event s button on the upper left above to enter the “Event Log” page. 2. Choose one of the three buttons shown on the page to view an event when necessary .
51 5.1.5 Change the Application Setting Please follow the steps below to change the applic ation setting through the network if necessary . Change the Application Setting — FTP Application Setting. Please follow the steps below to change the FTP setting via the netw ork if necessary to upload recording data live.
52 Change the Application Setting — SD Card Application Setting. Please follow the steps below to change the SD CARD setting via the network if necessary to upload recording data live. 1. Click the SD Card button on the top left to enter the “SD Card Application Setting” p age.
53 Change the Application Setting —SMTP Application Setting. Please follow the steps below to change the SMTP setting via the network if necessary . 1. Click the SMTP button on the left side to enter the “SMTP Application Setting” page. 2. Enter the attached file number as and when necessary .
54 Change the Application Setting —Language Setting. Please follow the steps below to change the Language setting via the network if necessary . 1. Click the Language button on the left side to enter the “Language Setting” page. 2. You have an option as to which l anguage to use.
55 Change the Application Setting —Rec ord Application Enable Setting. Please follow the steps below to change the setting via the network if necessary . 1. Click the Enable Record button on the left side of the record to enter the “Record Application Enable Setting” page.
56 Change the Application Setting —Record - Schedule. 1. Click the Application button on t he home page to enter the “Schedule” page. 2. Check/uncheck any/all of the first seven boxes se t v.
57 Change the Application Setting — Al arm Application Enable Setting. Please follow the steps below to change the setting via the network if necessary . 1. Click the Enable Alarm button on the left side of the record to enter the “Alarm Application Enable Setting” page.
58 Change the Application Setting —Motion Detection. Please follow the steps below to enable changes in the motion detection function of the alarm through the network if necessary . Set the motion detection: 1. Click the Motion Detection button on the left side of the Alarm to enter the “Motion Detection” page.
59 5.1.6 Change the SD card Settin g Please follow the steps below to change the SD card setting through the network if necessary . Change the SD card Setting — FILELIST of MEMORY CARD. Please follow the steps below to change the setting via the network if necessary .
60 5.1.7 Change the Pan/Tilt setting Click the Pan/Tilt button on the home page to open the S peed Do me Controller . 1. Click “ Configure ” to enter to the RS485 setting page (please refer to Change the System Setting — RS485 Setting ). Select a Speed Dome device ID from the drop-down list on the S peed Dome Controller .
61 5.1.8 PPPoE & DDNS Using the PPPoE 1. Install the XDSL software (obtained from your ISP dealer) in your PC. 2. Search your IP Camera's IP address: you can use your Network Viewer's Scan IP program, or just connect the IP Camera and the Video monitor .
62 T est: Go to the Internet. 1. Set your PC to enter the Internet. 2. Desktop → IE b rowser → T ype in the IP Camera’s IP address (the same address as i n the PPPoE settings and step 3 above) → Y ou can see the IP Camera images. DDNS settings 1.
63 5.2 The IP Camera CMS (Cen tral Management System ) This section provides instructions for installing and using the Central Management System ( CMS ) which is included with the IP Camera. The programs can be operated by a selected PC equipped with the following requirements.
64 5.2.2 Install the CMS in your PC Inst all the CMS from the s upported CD-R. 1. Exit all applications currently running in the selected PC. 2. Insert the supported CD in the CD-ROM driv e.
65 5.2.3 Login the IP Camera software Once the CMS is executed, a Login prompter will appear . Y ou must enter the default user name: admin , and the password: 9999 in the respective spaces (and confirm the p assword again the first time you log in).
66 2. Add a channel from the Add Device page. 3. (1) Click the Auto Search button at the bottom of the " Add De vi ce " page to discover the connection of the IP Camera-type device in the LAN. Instantl y the " Search Device " page will appear.
67 5.2.4 Operation 5.2.4.1 Device Managemen t Once the connection has been established, click the button to enter the Device Management windo w ( see the sample screen below .) On the left side of the window is the connected device that has bee n arranged when you established the connection.
68 NOTE: The Device Setting page: For the further settings of each channel, please select the device title on the left side and click the setting button to enter the setting pages of the device. Click the “Setting” button to bring up the device-setting pages.
69 5.2.4.2 Live View Press the button to enter the Live View page. 1 Add Live View Group: Press to add a new group of the live view . T o change the group name, please left click twice on the title of the group, and then enter the new title. Group Sequenc e: This button enables you to see the sequential display of the group.
70 The audio function is available. Press to activate the function and the icon will turn purple “ ”. Press again to deactivate the function. Recording function: The recording function is not available. The recording function is avail able. Press to activate the function and the icon will turn red “ ”.
71 5.2.4.3 PC Playback Press the button to enter the PC Playback page. 1 Click to choose the recording list by channel. Click to choose the recording list by time search. Enter the MONTH /DA Y /YEAR /HOUR /MINUTE you wish to search and click the button to proceed.
72 : Click to set the export function. The function fits the starting and ending points of an image display , when the user wants to transfer a file. St art/ End time: Set the start and end time that you want to export (backup) the recorded files to the A VI files.
73 5.2.4.4 DVR Remote Pla yback (for DVR devices only) Press the button to enter the DVR Remote Playb ack setting page. This setting p age is for co nnecting with the DVR devices.
74 5.2.4.5 Config Press the button to enter the Config setting page. NOTE: After finishing the settings of each page, please click Save to save the parameters. (1) User Click the icon to enter the User setting page. User List: Add Us er: 1.) Click to open the Add User window .
75 User Information: Provides the selected user ’s informat ion of Username, Description and Group. (2) User Gr oup Click the to enter the User Gr oup setting page. User Group List: Add Gr oup User: 1.) Click to open the Add Group User window . 2.) Enter the information of the Group Name and Description, then select the Authority .
76 (1) Folder for S napshot Images: Click to select (2) Folder for Export A V I Clips: Click to select the path to save the A VI files. Image Settings: Select the aspect ratio: ( NOTE: The STRETCH status : Images are resized to full screen status. The aspect ratio status: When you re size images, they will retain their natural proportions.
77 Undo: Undo the latest changes Restore Defaults: Recover the default setting. (5) Record Settings Click the icon to enter the Record setting page. 1 Click to add a new record saving path. Click to delete a selected recording path. 2 Max. Usage: Set the maximum recording quota from the drop-do wn list.
78 Sets the starting time of recording from the drop-down list. Sets the ending time of recording from the drop-down list. Clicks the icon to enable the just added schedule. Clicks the icon to disable the selected schedule. 2 The working area: (1) Click the working area directly to add a new schedule as you wish.
79 5.2.4.5 T ra y Press the button to minimize the CMS monitor into the systray* of the Windows taskbar . Right click the button once to select the functions on the list: .
80 6. ADV ANCED OPERA TION Question 1: How to view the li ve images of the IP Camera via the Microso ft Internet Explorer on the Desktop PCs or the lapt op computers in a si tuation where ther e are n.
81 4. Click the Submit button to submit the setting. NOTE: Please remember to insert the SD card in to the built-in SD slot of the unit first. Set the recording time (the A VI duration) of ◇ the SD card 1. Click the Applica tion button in the home page into the “SD-Card APPLICA TION SETTI NG” page.
82 2. Click the PPPoE button on the left side of the page to enter the “PPPoE SETTING” page. 3. Choose “ON” from the “PPPoE mode” list to activate it. 4. Enter the Account and the Pass word which are provided from your ISP . 5. Click the Submit button to submit the setting.
83 Set the upload rate ◇ 1. Click the Application button. 2. Click the FTP button on the left side of the page to enter the “FTP APPLICA TION SETTING” page. 3. Set the last item “Upload Rate” at the bottom of the page to the rate you want. If you want to record at the rate of 1F/8S, please choose “1F/8S” in t he drop-down list.
84 7. SPECIFICA TIONS LC-7314 H.264 CCD Box IP-Camera (PAL) Video sensor 1/3” Sony Super HAD CCD (with HQ1 DSP) Horizontal resoluti on 520 TV Lines Lens C / CS mount Auto Iris DC drive AES 1/50 ~ 1/100000 sec Min. illumina tion 0.5 Lux @ F1.2 Video system Day & Night Yes (Mechanical IR-Cut filter) Video compressi on Simultaneous H.
85 8. Functions of client PC System requirement Windows 2000, XP or above Browser IE 6.x Live Monitor Max. 16 S plit , Real T ime REC/ Capture/ Audio/ Live Event/ Full Screen Playback Viewer Playback, T ime / live event Search / Export (JPEG / A VI) Settings Device/ System/ Camera management/ web page Multi-camera link Max.
86 APPENDIX 1. –SCANIP Follow the instructions below to use the SCANIP sof tware to search the IP camera devices from a local location. 1. Click the button to discover the connection of the all-type device in the LAN. The Device T ype will display the connection of the all-type device.
87 iii. Select and double click any of the addresses in the “Free IP Address” box on the right to enter it into an IP Address on the left. iv. T o change an y IP address, type in the new address i.
88 APPENDIX 2. –IP Camera UPnP How T o The most troublesome issue when you setup an IP Camera ® is that you have no idea what the IP address of this device is.
89 Figure 2 Step 2: When Control Panel appears, double-click the Netw ork Connections icon. The Network Connectio ns dialog box appears. See Figure 3. Figure 3 Step 3: Click the Protocols tab in the Network Connections dialog box.
90 Figure 5 Step 5: In the Internet Protocol(TCP/IP) Properties dialog box, choose Use t he following IP Address to indicate that you do not wish to use DHCP , and assign IP Address 192.168.1.200 with Subnet mask 255.255.255.0. Click OK when you finish it.
91 2. Install UPnP Packets As described before, Microsoft Windows XP ® doesn’t start the UPnP service by default; however , we have to install some p ackets before we initia lize it. The following steps w ill help you to install them. Step1: From the Start m en u , poin t to Set Program Access and Default , and then click it.
92 Figure 10 Step 4: Check UPnP User Interface , and choose OK . See Figure 1 1. Figure 11 Step 5: When the original Network Component Wizard dialog box retu rns, click Next .
93 Step 6: Af ter about one minute the UPnP installation will be done, and choose Finish to close it. See Figure13. Figure 13 3. Turn on Ser vices After installation, we should turn on the relative services to start the UPnP protocol. The following procedures will teach you how to do it.
94 Figure15 Step 3: Click the Services icon in the Administrative T ools dialog box. See Figure16. Figure16 Step 4: When the Services dialog box shows up, double click the SSDP Discovery Service icon .
95 Figure17 Step 5: Choose Auto ma t ic in the Startu p t yp e , and click OK to start it. See Figure18. Figure18 Step 6: When the Services dialog box appears a gain, double click the Uni versal Plug and Play Device Host icon.
96 Figure19 Step 7: Choose Auto ma t ic in the S tartup type, press the Start button, and click OK to start it. See Figure20. Figure20 Step 8: Restart your system.
97 4. Scan IP Cameras ® through My Netw ork Place After your installation and starting services, the UP nP protocol will take effect. You can scan all IP Cameras ® in My Network Place like Figure21 and Figure22 below.
98 APPENDIX 3. –The ARP function Setting the IP Address The Ethernet interface on the IP Camera has a def ault IP address (192.168.1.168) that most likel y needs to be changed to make it work on your lo cal network. You need to acquire a u nique IP address (ask your network administrator).
99 ARP and ping from U NIX or GNU/Linux: 1. Start a shell 2. Type the following as superuser (root): arp -s <IP address> <Ethernet address> [ or arp -s <IP address> < MAC address>] ping <IP address> Example: arp -s 192.168.
100 APPENDIX 4. –Register as a DDNS member The DDNS （ dynamic domain name system ） is a function which is provided by an American company . Please refer to www .d yndns.com . This chapter provides the user with the basic instructions on how to register a free DDNS service.
101 Figure 2 Figure 3 Click “My Services” to enter the service page. Please click the “Add Host Service” item which is below the ”My Hosts“ item, as shown in Figure 4. Click “Add Host Service”, and its service items will appear . The Add Dynamic DNS Host item helps to add a new DDNS.
102 Figure 4 Figure 5 All we have to set in this page is the “H ostname” item. The user can choose a Sub Hostname as s/he likes from the right-hand side of the Hostname’s drop-down list. NOTE: Y ou don’t have to set the “IP Address” in the same format as the came ra’s IP Address.
103 Figure 6.
104 APPENDIX 5. –F AQ 1. How to disable the DHCP function and use a static IP instead? A ： T urn up the “DIP SWITCH” from “3” to “4” and change the relative net work settings, the IP Address, NetMask and Gateway on the image web page. 2.
An important point after buying a device Approach Tech LC-7314 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Approach Tech LC-7314 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Approach Tech LC-7314 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Approach Tech LC-7314 you will learn all the available features of the product, as well as information on its operation. The information that you get Approach Tech LC-7314 will certainly help you make a decision on the purchase.
If you already are a holder of Approach Tech LC-7314, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Approach Tech LC-7314.
However, one of the most important roles played by the user manual is to help in solving problems with Approach Tech LC-7314. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Approach Tech LC-7314 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
