EN
Linear logo
Official user manual

Linear Single Channel Receiver (MDR)

2 pages·156 KB·Radio·PDF·ENDEFRITNLJA
Linear Single Channel Receiver (MDR)
Table of Contents 75 sections STEP 1B MDRM/MDRM2 Recessed Receiver Operator · CORNER HOLE IS · LOCATIONS 2 & 3 · SHARED FOR · … ShowHide
Page 1 of the Linear Single Channel Receiver (MDR) user manual — COMMON
Page 1 · click to enlarge
Page 1

MDRM - Single-channel internal receiver (fits operators with

MDRNR - Single-channel external receiver with solid state output.

MDRM2 - Two-channel internal receiver (fits operators with

recessed receivers) with solid state output on channel one and

The Model TF524 step-down transformer must be used to power

the receiver when connecting to a two-terminal operator or one

that supplies other than 24V. Install the screws supplied into the

brass terminals on the receiver. Connect the transformer wires to

Terminals 1 & 3 (polarity not important). Connect receiver

Terminals 1 & 2 to the two operator terminals (polarity not

Location. Locate the program button and LED on the side of the

Linear Single Channel Receiver (MDR) — STEP 1B MDRM/MDRM2 Recessed Receiver Operator diagram (page 1)
Fig. 1 · STEP 1B MDRM/MDRM2 Recessed Receiver Operator

MDR - Single-channel external receiver with relay output.

MDR2 - Two-channel external receiver with relay outputs.

recessed receivers) with solid state output.

relay output on channel two.

The MegaCode series of digital receivers are wireless radio

controls designed for use with automatic garage door and gate

openers. The MegaCode radio format provides unparalleled

security. The transmitter and receiver can be programmed to more

MegaCode receivers and transmitters do not contain a typical

“coding switch”. Each transmitter is pre-set at the factory to a

unique code. The receiver is programmed by sending a signal to

it from the transmitter(s) that are going to be used with it. This

stores the transmitters code into the receiver’s memory. The

receiver will retain its memory even without power. The receiver

will activate only from these “memorized” transmitters. Each

MegaCode receiver can remember a maximum of 10

Receivers are normally powered with 24 volts AC/DC from the garage

door or gate operator. Two-channel receivers provide wire

STEP 1B MDRM/MDRM2 Recessed Receiver Operator

Installation. Loosen operator terminal screws. Install receiver

into operator “pocket”. Connect Terminals 1, 2 & 3 on the receiver

STEP 3 Optional Receiver Mounting Bracket. If the receiver

isn’t going to be mounted directly to the operator terminals, an

optional mounting bracket is supplied. It can be installed three

ways onto the MDR or MDR2 case. Screw the bracket to a wall

connections to activate the operator’s light or control other devices.

CORNER HOLE IS

LOCATIONS 2 & 3

SHARED FOR

LOCATION 3

Linear Single Channel Receiver (MDR) — CORNER HOLE IS diagram (page 1)
Fig. 2

1, 2 AND 3 ANTENNA

Linear Single Channel Receiver (MDR) — 1, 2 AND 3 ANTENNA diagram (page 1)
Fig. 3

to Terminals 1, 2 & 3 on the operator.

or stud and snap the receiver onto it.

than a million different codes.

DESCRIPTION

MOUNT IN THREE

transmitters.

BRACKET CAN

PLACES

Linear Single Channel Receiver (MDR) — BRACKET CAN diagram (page 1)
Fig. 4

STEP 2 MDR2/MDRM2 Two-channel Receiver Installation.

Connect the receiver to the operator as described in the previous

step. The channel-two pigtail wires can be connected to the

12 COMMON GROUNDRELAY
123 COMMON GROUNDRELAY24-VOLTS RADIO POWER

TERMINAL

DIGITAL RECEIVERS

Installation Instructions

LIGHT

MDR, MDR2, MDRNR,

TO OPERATOR

CONNECT

RECEIVER

DIRECTLY

MDRM, MDRM2

GROUND RELAY 24-VOLTS RADIO

POWER

BROWN ORANGE RED

RELAY

NORMALLY

CLOSED

RELAY

NORMALLY

OPEN

operator.

COMMON

RELAY

COMMON

(#0) · MegaCode Series

Page 2 of the Linear Single Channel Receiver (MDR) user manual — CH2 CH1
Page 2 · click to enlarge
Page 2

Copyright © 1999 Linear Corporation 210188 B

STEP 8 Test receiver. Be sure door area is clear. Activate

each transmitter. The receiver relay should click (relay output

models only) and the operator should activate. Wait 1 second

This product is warranted to the consumer against defects in material and workmanship for one year

from the date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will

repair, or at its option, replace, any device it finds that requires service under this warranty, and will

return the repaired or replaced device to the consumer at the warrantor’s cost. For warranty service

and shipping instructions contact warrantor at the address shown below. Devices must be sent to

warrantor for service at owner’s expense. The remedies provided by this warranty are exclusive. Implied

warranties under state law are to the one year period of this written warranty. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In order

to be protected by this warranty, save your proof of purchase and send copy with equipment should

repair be required. This warranty gives you specific legal rights, and you may also have other rights

Linear radio controls provide a reliable communications link and fill an important need in portable

1 For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

1 A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

1 Changes or modifications to the device may void FCC compliance. 1 Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

PRESS TRANSMITTER

All products returned for warranty service require a Return Product Authorization Number (RPA#).

IS READY, PRESS THE DESIRED

Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

BUTTON TO TEST

TRANSMITTER BUTTON

wireless signaling. However, there are some limitations which must be observed.

WHEN RECEIVER

AS TRANSMITTER

IS ENTERED INTO

RECEIVER LED

WILL FLICKER

PROGRAMMING

MEMORY

CHANNEL 1

BUTTON

OF OBSTRUCTIONS

WHEN RECEIVER

LED WILL LIGHT

BE SURE DOOR

AREA IS CLEAR

between each activation.

LIMITED WARRANTY

CH2 CH1

IS READY

WARNING!

which vary from state to state.

IMPORTANT !!!

PROGRAMMING

CHANNEL 2

BUTTON

STEP 5 Program receiver. Momentarily press the receiver’s

program button (channel one or two). The red programming LED

will light if there’s room in the receiver’s memory for another

transmitter (10 maximum per receiver). The LED stays on for

about 5 seconds. A transmitter must be entered while the LED

is on. Press the desired transmitter button. The LED will flicker

¯ NOTEBe sure to press the receiver program button for less

¯ WARNING! Door operator will not activate when the

receiver is being programmed from the transmitter, but the

door operator will activate the next time the transmitter is

¯ NOTEThe programming LED also monitors radio signals

entering the receiver. It is common to see an occasional blink

from the LED. The LED will also light when any transmitter

tuned to the receiver’s frequency (programmed into the

STEP 7 Review memory. Press and hold the receiver’s

program button (channel one or two) until the LED begins to flash

(about 3 seconds) and then release the button. Count the number

of flashes. The number of flashes equals the number of

¯ NOTEDon’t hold down the programming button longer

than 5 seconds, the receiver’s memory for that channel will

¯ NOTEThe same transmitter (or the same transmitter button

on multi-button transmitters) cannot be programmed into both

¯ NOTEIf the receivers LED flashes continuously when a

transmitter isn’t being activated, the receiver is too close to an

electrical noise source. Move the receiver away from the noise

TOTAL NUMBER OF TRANSMITTERS

transmitters programmed into that channel of the receiver.

LED WILL FLASH, COUNTING THE

PROGRAMED TO THAT CHANNEL

indicating that the receiver has accepted the transmitter.

than 2 seconds (any longer may erase memory.)

CH2 CH1

source or call technical services for assistance.

CONTINUOUSLY FLASHING LED MAY

INDICATE ELECTRICAL NOISE

CH2 CH1

receiver channels one and two.

activated after programming.

receiver or not) is activated.

INTERFERRENCE

PRESS PROGRAM BUTTON

FOR THREE SECONDS

be erased (Step 9).

(CHANNEL 1 OR 2)

CH2 CH1

THEN RELEASE

STEP 4B MDRM/MDRM2 Program button and LED

Location. Locate the program button and LED on the back of the

STEP 6 Add additional transmitters. Repeat Step 5 for each

transmitter used with this receiver. Be sure to press the

receiver’s program button each time a new transmitter or a

different transmitter button on a multi-button transmitter is

If the LED doesn’t come on when the receiver’s program button is

pressed, the receiver’s memory is full (10 transmitters total). Use

the erase function (Step 9) to remove transmitters form the

STEP 9 Erasing receiver memory. Transmitters may be

erased from the receiver’s memory by pressing and holding the

receiver’s program button (channel one or two) for 5 seconds or

more. After the LED blinks (count of transmitters) it will blink one

more time for channel one and twice for channel 2 as the

receiver’s memory for that channel is erased. All transmitters

AS THE TRANSMITTERS ARE ERASED

TOTAL NUMBER OF TRANSMITTERS

THEN IT WILL BLINK ONE MORE TIME

TRANSMITTERS PRESS

THE DESIRED BUTTON

LED WILL FLASH, COUNTING THE

PROGRAMED TO THAT CHANNEL.

WITH MULTI-BUTTON

for each receiver channel are erased at the same time.

P R O G R A I N

CH2 CH1

FROM THAT CHANNEL

THEN PRESS TRANSMITTER BUTTON

L E

PRESS CHANNEL 1 OR CHANNEL 2

FOR FIVE SECONDS OR MORE

PRESS PROGRAM BUTTON

PROGRAM BUTTON FIRST

(CHANNEL 1 OR 2)

receiver’s memory.

CH2 CH1

C H A N N E L O N E

P R O G R A I N

C H A N N E L T O

P R O G R A I N

receiver case.

CH2 CH1

B U T T O

B U T T O

pressed.

Ask about the Linear Single Channel Receiver (MDR)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Single Channel Receiver (MDR)

Be the first to ask — other owners or our team will answer.

Original document

Linear Single Channel Receiver (MDR) manual PDF

2 pages·156 KB·Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…