EN
Linear logo
Official user manual

Linear Radio Receiver (1099)

1 pages·32 KB·Radio·PDF·ENDEFRITNLJA
Linear Radio Receiver (1099)
Table of Contents 32 sections LINEAR CORPORATION · WARRANTY · ADDITIONAL INSTALLATION INFORMATION · CONTROL · … ShowHide
Page 1 of the Linear Radio Receiver (1099) user manual — INSTALLATION
Page 1 · click to enlarge
Page 1

be necessary to remove it from its mounting and hold near

the windshield. Try different locations and positions. If

1. The antenna must be connected to the receiver for normal use.
2. If the opener fails to operate, check to see that 115 VAC power is present. Check circuit breakers or for a system
3. If the opener operates by pressing the wall button, but not when the transmitter button is pressed, the radio

controls are probably at fault. Check to make sure

both transmitter and receiver code switches are set

to the exact same code since a difference of just one

switch will prevent operation. Check transmitter bat-

tery, location of the transmitter and receiver installation.

4. Try mounting the antenna at a more favorable remote location by utilizing the coaxial kit.

If, after performing the above operational check, it is

necessary to return the radio controls, return both the

transmitter and receiver to your dealer for repair or

replacement or they may be returned, postage prepaid,

ALL MULTI-CODE garage door related products carry an

eighteen (18) month warranty against defects in

workmanship or material. This warranty begins at the date

of manufacture, for eighteen months. Linear Corporation

warrantees our product only to our authorized dealers and

distributors, and not to the end customer. If you have any

questions about our warranty, please ask your dealer to

determine the nature and scope of his warranty. Linear

Corporation does not assume, and is not responsible for,

any real or consequential damages from claims against the

performance of our product, nor is it liable for any costs

related to loss of life, property, or revenue. Further, Linear

Corporation is in no way responsible for installation of our

product, and will assume no costs to re-installation or

removal. Linear Corporation’s Warranty is in lieu of all

unintentional radiators which are not expressly approved

by LINEAR CORPORATION could void the user’s author-

ity to operate this equipment. This applies to intentional

and unintentional radiators certified per Part 15 of the

operation is still unsatisfactory, check the following:

2055 Corte del Nogal • Carlsbad, CA 92009 (760) 438-7000

LINEAR CORPORATION

other warranties, expressed, or implied.

directly to Linear Corporation.

F.C.C. rules and regulations.

power failure.

WARRANTY

IF YOU HAVE THE MODEL 1099-40: The red wire

will go to the positive 12 volt terminal in the operator. The

black wire will go to the negative terminal or ground

terminal of the operator. Connect the two gray wires as

specified by the manufacturer of your operator. If such

instructions do not exist, wire the two gray wires in

At this point you should mount your 1099 receiver to its

After you have mounted your receiver, test it with the

enclosed antenna for range, noting the coverage that you

get from all desired operating locations. If greater range or

coverage pattern is necessary, you may need the 1066

Coaxial Wiring Kit, which is available from your dealer.

BNC antenna fitting. If necessary, you may use a TYPE

BNC to TYPE F adapter, allowing you to use fittings found

where television antennas are sold, along with 75 ohm

antenna wire. It is not advisable to use lengths greater than

Linear Corporation has taken every possible precaution to

make the 1099 receiver as reliable as possible. We think

1. Be sure the unit is sealed from moisture, and, if at all possible, keep it away from direct moisture.
2. In those installations where vibration may be a factor, be sure to use a fastening compound, such as LOCTITE

(TM) on the mounting screws to insure reliable

3. If this, or any other equipment is being used in a safety-related device, be sure to test the entire system at

the time of installation, and at frequent intervals, to

To check operation, move back a reasonable distance

(about 50 feet) and press the transmitter button. Operation

should be reliable at this distance but environment and

location of both the transmitter and receiver will affect the

range. If the transmitter is stowed well out of sight, it may

permanent installation, if you have not already done so.

ADDITIONAL INSTALLATION INFORMATION

parallel with the pushbutton terminals (see figure 4).

CONTROL

BOX

20 feet, as this may affect range or tuning.

RELAY

RELAY

the following notes should be observed:

determine that it is working properly.

BLACK 1

GRAY

GRAY

ANTENNA INSTALLATION

OPERATIONAL CHECK

RED

RECEIVER

mounting.

receiver performance by using a coaxial kit available from

Begin your installation of the 1099 by correctly wiring the

receiver to the devices you will be using. WE URGE YOU

TO BECOME FAMILIAR WITH THE INSTRUC-

TIONS THAT THE MANUFACTURER OF YOUR

EQUIPMENT HAS PROVIDED. SINCE, IN

MANY CASES, THESE INSTRUCTIONS WILL DETER-

MINE THE WAY IN WHICH THE 1099 RECEIVER

The receiver should be mounted near the opener power

head and can be installed in any position by using screws

and the two slots in the cover flanges. Select a location and

position that permits access to the terminals and space for

the antenna as clear of metal structures as possible and

IF YOU HAVE THE MODEL 1099-20: Plug the trans-

former into a convenient 115 volt outlet. Connect the

remaining gray wires as specified by the manufacturer of

your operator. If such instructions do not exist, wire the

two gray wires in parallel with the pushbutton terminals. If

the operator has a three wire terminal, the proper terminals

will usually be marked “1” and “2” or “24V” and

IF YOU HAVE THE MODEL 1099-30: Wire the red and

black wires to a 24VAC power supply. Connect the

remaining gray wires as specified by the manufacturer of

your operator. If such instructions do not exist, wire the

two gray wires in parallel with the pushbutton terminals. If

the operator has a three wire terminal, the proper terminals

will usually be marked “1” and “2” or “24V” and

1 2 3 GRAY 4

RECEIVER

ANT.

WALL BUTTON

CONTROL

BOX

TRANSFORMER

GRAY

GRAY

PLUG IN

preferably in a vertical position.

GRAY

BLACK

WILL BE INSTALLED.

“RELAY” (see figure 2).

“RELAY” (see figure 3).

RED

GRAY

OPERATOR

COMMON

PRIMARY 24V

RELAY

RECEIVER

your dealer.

TRANS.

Your Multi-Code Radio Controls are designed specifically

for the remote control of industrial door or gate openers

and to give years of dependable service without

Before you continue to read these instructions, note that

there are 3 versions of the model 1099 receiver. The model

1099-20 uses a 115-24 volt transformer. The model 1099-40 comes with 4 wire connections for use with 12VDC systems. The model 1099-30 comes with 4 wire connections for use with 24VAC systems. In addition, if

you should choose to cut the transformer away from the

1099-20, this modified product MUST ALSO BE WIRED TO 24VAC ONLY.

The code is determined by the positions of the 10 small

switches numbered 1 through 10 located on the receiver

board. To gain access to the switch, remove the top section

of the case. Any combination of ON (CLOSED) or OFF

(OPEN) positions can be selected by using a small

screwdriver or ball point pen (see figure 1). We strongly

urge that you avoid the following code schemes: ALL ON,

ALL OFF, 2, 4, 6, 8, 10, on or 1, 3, 5, 7, 9, on. These codes

are frequently used by other manufacturers, and create the

possibility of false operation, and may be less secure than

Be certain to check that the code is functional before

The receiver comes equipped with a BNC receptacle and

an antenna with a BNC plug. The antenna can be plugged

directly into the receptacle, or it can be moved away from

a metal structure, or to an outside location for better

Installation Instructions

MODEL 1099 RECEIVERS

  • Disconnect power before any installation or repair.
  • Wear safety glasses.

RADIO CONTROLS

Figure 1 CODE SWITCH

GARAGE DOOR

1 2 3 4 5 6 7 8 9 10

OPEN

completing the installation.

SELECTING A CODE

WARNING:

other code schemes.

INSTALLATION

adjustment.

Show 4 more labels / short text on this page
(1099-40) · (1099-30) · Figure 2 (1099-20) · ®

Ask about the Linear Radio Receiver (1099)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Radio Receiver (1099)

Be the first to ask — other owners or our team will answer.

Original document

Linear Radio Receiver (1099) manual PDF

1 pages·32 KB·Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…