EN
Linear logo
Official user manual

Linear Remote Control (DT-2A)

2 pages·57 KB·Remote Control·PDF·ENDEFRITNLJA
Linear Remote Control (DT-2A)
Table of Contents 28 sections Code Setting Instructions · Two-button Digital · DT-2A · Delta-3 Series · … ShowHide
Page 1 of the Linear Remote Control (DT-2A) user manual — NOTE:
Page 1 · click to enlarge
Page 1

Code Setting Instructions

(800) 421-1587 • www.linearcorp.com

Two-button Digital

DT-2A

Delta-3 Series

Transmitter

This product is warranted to the consumer against defects in

material and workmanship for one year from the date of purchase.

This warranty applies to first retail buyers of new devices. Warrantor

will repair, or at its option, replace, any device it finds that requires

service under this warranty, and will return the repaired or replaced

device to the consumer at the warrantor’s cost. For warranty service

and shipping instructions contact warrantor at the address shown

below. Devices must be sent to warrantor for service at owner’s

expense. The remedies provided by this warranty are exclusive.

Implied warranties under state law are to the one year period of this

written warranty. Some states do not allow limitations on how long

an implied warranty lasts, so the above limitation may not apply to

you. In order to be protected by this warranty, save your proof of

purchase and send copy with equipment should repair be required.

This warranty gives you specific legal rights, and you may also have

Linear radio controls provide a reliable communications link and fill

an important need in portable wireless signaling. However, there

* For U.S. installations onlyThe radios are required to comply

with FCC Rules and Regulations as Part 15 devices. As such,

they have limited transmitter power and therefore limited

* A receiver cannot respond to more than one transmitted signal

at a time and may be blocked by radio signals that occur on

or near their operating frequencies, regardless of code set-

* Changes or modifications to the device may void FCC compli-

* Infrequently used radio links should be tested regularly to

* A general knowledge of radio and its vagaries should be

gained prior to acting as a wholesale distributor or dealer, and

Copyright © 1999 Linear Corporation 207403 G

All products returned for warranty service require a Return

Product Authorization Number (RPM). Contact Linear Technical

Services at 1-800-421-1587 for an RPA# and other important

these facts should be communicated to the ultimate users.

protect against undetected interference or fault.

LIMITED WARRANTY

IMPORTANT !!!

are some limitations which must be observed.

other rights which vary from state to state.

range.

tings.

ance.

details.

You can select any one of 256 codes on

Switch “A” and also any one of 256 codes on

The manufacturer strongly recommends that

you test your equipment frequently. From the

time of installation, it is absolutely necessary

to test the system at least once a week. It is

also good practice to change the 9-volt battery

The transmitter transmits continuously with

button depression. An LED lights during

256 AVAILABLE CODES ON EACH SWITCH

transmission to indicate battery operation.

NOTE:

NOTE:

every six months.

Show 5 more labels / short text on this page
Right Button "B" · Left Button "A" · Battery · Test Light · switch “B”
Page 2 of the Linear Remote Control (DT-2A) user manual — CODING SWITCH "A"
Page 2 · click to enlarge
Page 2

Switch “A” is designed for use with a garage

door opener. The code set to Switch “A” must

be identical to the code set in the receiver to

Switch “B”, under the back cover is designed

for use with less-frequently changed codes,

such as a community gate operated by

Push-button “B”. The code set into Switch “B”

must be identical to the code set in the

receiver to be used in conjunction with

be used in conjunction with Push-button “A”

CODING

SWITCH

"B"

TRANSMITTERS CODE MUST

MATCH RECEIVER CODE

BACK COVER REMOVED

TO ACCESS SWITCH "B"

Push-button “B”.

REAR VIEW WITH

and 8 ON CODING

SWITCH

"A"

To set a code, select any combination of ON

or OFF positions for the switch keys

numbered 1-8. Use a paper clip or other

pointed object (except a pencil or pen) to set

the keys on the coding switch. The ON

position is when the top of the switch is down.

To gain access to Coding Switch “B”, first

remove the screw in the middle of the back

cover. Remove the back cover to expose the

8-key switch. To set a code, select any combination of ON

and OFF positions for the switch keys, in the

same manner as described for Coding Switch

It is not advisable to set a code with all keys

ON, OFF, or alternating ON and OFF,

because these codes are too easy to

SETTING CODE SWITCH “B”

CAUTION:

7 1 4 3

Keys 1, 2, 3, 4,

F

F

O

O

N

duplicate.

“A”.

There are two digital coding switches in the

DT-2A transmitter. Code Switch “A” is

exposed by removing the battery access

cover. It is the coding switch for the left button

on the front of the transmitter (Button “A”).

Code Switch “B” is the coding switch for the

right button on the front of the transmitter

(Button “B”). The switch is located behind the

back cover of the transmitter. To access

Coding Switch “B”, it is necessary to remove

the screw located in the middle of the back

Before removing the battery access door,

loosen battery clip screw and rotate clip away

from door. To open the battery access cover

and gain access to Coding Switch “A”, lift off

the small L-shaped cover by inserting your

thumbnail or a small screwdriver under either

of the two slots at the edge of the case. The

DT-2A TWO-BUTTON TRANSMITTER

coding switch has eight keys numbered 1-8.

CODING SWITCH "A"

SETTING CODE SWITCH “A”

BATTERY

CODE SETTING

BATTERY DOOR

ROTATE CLIP

AWAY FROM

cover.

Keys 5, 7 · and 6 OFF

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linear Remote Control (DT-2A)

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linear Remote Control (DT-2A)

Be the first to ask — other owners or our team will answer.

Original document

Linear Remote Control (DT-2A) manual PDF

2 pages·57 KB·Remote Control·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…