
March 2002

The following paragraph does not apply to any country/region where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In the United Kingdom and Eire, call 0628-481500. In other countries/ regions, contact your point of purchase.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries/regions in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
© 2003 Lexmark International, Inc. All rights reserved.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.


Trademarks
Lexmark, Lexmark with diamond design, FontVision and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries/regions.
ImageQuick and OptraImage are trademarks of Lexmark International, Inc.
Operation ReSource is a service mark of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
PostScript® is a registered trademark of Adobe Systems Incorporated. PostScript 3 is Adobe Systems’ designation of a set of printer commands (language) and functions included in its software products. This printer is intended to be compatible with the PostScript 3 language. This means the printer recognizes PostScript 3 commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
Details relating to compatibility are included in the Technical Reference.
The following terms are trademarks or registered trademarks of these companies:
Albertus The Monotype Corporation plc
Antique Olive Monsieur Marcel OLIVE
Apple-Chancery Apple Computer, Inc.
Arial The Monotype Corporation plc
CG Omega Product of Agfa Corporation
CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation
Chicago Apple Computer, Inc.
Clarendon Linotype-Hell AG and/or its subsidiaries
Geneva Apple Computer, Inc.
GillSans The Monotype Corporation plc
Candid Agfa Corporation · Eurostile Nebiolo · Trademarks

Helvetica Linotype-Hell AG and/or its subsidiaries
Hoefler Jonathan Hoefler Type Foundry
ITC Avant Garde International Typeface Corporation Gothic
ITC Bookman International Typeface Corporation
ITC Lubalin Graph International Typeface Corporation
ITC Mona Lisa International Typeface Corporation
ITC Zapf International Typeface Corporation Chancery
Joanna The Monotype Corporation plc
Monaco Apple Computer, Inc.
New York Apple Computer, Inc.
Palatino Linotype-Hell AG and/or its subsidiaries
Stempel Linotype-Hell AG and/or its subsidiaries Garamond
Times New The Monotype Corporation plc Roman
TrueType Apple Computer, Inc.
Univers Linotype-Hell AG and/or its subsidiaries
Other trademarks are the property of their respective owners.
The printer resident software contains:
Click the title of the document you want to review:

The Lexmark modified GNU licensed software is free software; you can redistribute it and/or modify it under the terms of the licenses referenced above. These licenses do not provide you any rights to the Lexmark copyrighted software in this printer.
Since the GNU licensed software that the Lexmark modifications are based upon is supplied explicitly without warranty, use of the Lexmark modified version is similarly provided without warranty. See the warranty disclaimers in the referenced licenses for additional details.
To obtain source code files for the Lexmark modified GNU licensed software, launch the drivers CD that shipped with your printer and click Contact Lexmark.
software.
telephone, and so on) during a lightning storm.
This printer has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
Class A computing device, use a properly shielded and grounded cable. Use of a substitute cable not properly shielded and grounded may result in a violation of FCC regulations.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, S.A., Boigny, France.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950.
interference, in which case, the user may be required to take adequate measures.
Electronic emission notices


This apparatus is approved under the approval number NS/G/1234/J/100003 for the indirect connections to the public telecommunications systems in the United Kingdom.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
The EPA ENERGY STAR Office equipment program is a partnership effort with computer manufacturers to promote the introduction of energy-efficient products and to reduce air pollution caused by power generation.
Companies participating in this program introduce personal computers, printers, monitors, or fax machines that power down when they are not being used. This feature will cut the energy used by up to 50 percent. Lexmark is proud to be a participant in this program.
As an ENERGY STAR Partner, Lexmark International, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Noise emission levels


The following illustrations show a standard model configuration and a fully configured network printer (without the optional staple punch finisher). If you have attached paper handling options to your printer, it may look more like the fully configured model. For information on other possible configurations, refer to the Setup Guide.
Standard model configuration Fully configured


This printer is a network color printer that uses electrophotographic technology to deliver high quality images, presentation graphics, line art, and text. Its fast output–up to 28 pages per minute (ppm) for both four-color and monochrome print jobs–makes it the ideal solution for businesses where performance is critical.
The printer's flexible design allows it to support a variety of printing needs. For example, the “toner darkness” settings lets you conserve toner when maximum print quality is not necessary. You can also adjust the printed colors to more closely represent the colors on your computer display.
A variety of connectivity options make the printer an excellent choice for all types of system environments. You can attach one internal adapter to support network configurations requiring Ethernet, Token-Ring, LocalTalk, serial, infrared, or additional parallel ports. You can even attach a class 1 fax modem to the optional serial port and receive faxes directly to your printer.
The printer also offers flexible paper handling. It supports a wide variety of paper sizes, from A5 to A3, Banner (11.7 x 36 in.), and 12 x 18 in., and has a standard multipurpose feeder that makes it easy to print on envelopes, transparencies, labels, card stock, glossy, and non-standard size paper. You can add up to three optional drawers to the base printer, which can increase the printer's paper
Printer overview

capacity to 2300 sheets. You can also add an optional high capacity feeder making the total paper capacity 5300 sheets. A finisher that offers staple, hole-punch, and job offset options is also available to give you a more professional and efficient output.
Your printer can print four-color and mono jobs at up to 28 ppm. With all printers, print speed varies depending on specific characteristics of the job, such as the size of the formatted page, the number of fonts, the number and complexity of images and graphics, and so on. Printing a mix of color and mono jobs may also slow printing, depending on the printer settings you have chosen.
Your printer ships with at least 128MB of memory for fast, efficient processing of color jobs. (Network and other models may ship with more memory.)
You can install an optional hard disk for storing downloaded resources and job statistics, and for spooling or collating print jobs. Resources stored in flash memory or on disk are retained in memory even after the printer is turned off and back on.
Lexmark recognizes that there are third party suppliers of memory features for Lexmark products. Lexmark does not recommend, test, or support third party memory features. We cannot guarantee their reliability, accuracy, or compatibility. Any damage to a Lexmark product caused by third party memory is not covered by the product's warranty. Lexmark may require that all third party features be removed before a product is supported or serviced.
The printer comes equipped with a 550-sheet paper tray and a multipurpose feeder. (Some models may ship with a second 550-sheet tray.) The multipurpose feeder lets you load a stack of envelopes, transparencies, labels, card stock, glossy or heavier papers for multiple-page jobs. To increase paper feeding capacity, you can attach up to three optional drawers, each with a 550-sheet tray, and one optional 3000-sheet high capacity feeder.
Print speed

This section contains information about understanding the operator panel, changing printer settings, and understanding operator panel menus.
You can change most printer settings from your software program or printer driver. Settings you change from the application or printer driver apply only to the job you are preparing to send to the printer.
Changes made to printer settings from a software program override changes made from the operator panel.
If you cannot change a setting from your program, use the operator panel or the remote operator panel available from MarkVision™ Professional. Changing a printer setting from the operator panel or from MarkVision Professional makes that setting the user default. Refer to the drivers CD for information about MarkVision Professional.
Printing

Understanding the operator panel
The printer operator panel has a two line by 16-character liquid crystal display (LCD), five buttons, and one indicator light.
LCD
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
The indicator light gives information about the status of your printer. If the light is:
Use the five operator panel buttons to open a menu, scroll through a list of values, change printer settings, and respond to printer messages.
The numbers 1 through 6 appear beside the operator panel buttons; these numbers are used to enter personal identification numbers (PIN) for Print and Hold jobs. For more information, see Using the Print and Hold function.
Understanding the operator panel
Indicator light

The following information describes the functions of each button.
panel.
Go Press the Go button to:
If you’ve changed printer settings from the operator panel menus, press Go before sending a job to print. The printer must display Ready for jobs to print.
Menu Each end of the button has a function. Press Menu:
For menu items with numeric values, such as Copies, press and hold Menu to scroll through the values. Release the button when the number you want is displayed.
Select Press Select to:
Return Press Return to return to the previous menu level or menu item.
Stop Press Stop at the Ready, Busy, or Waiting message to temporarily stop all activity and take the printer offline. The operator panel status message changes to Not Ready.
Press Go to return the printer to Ready, Busy, or Waiting.
From the operator panel, you can select menu items and associated values to print your jobs successfully. You can also use the panel to alter the setup and operating environment of the printer. See Using printer menus for an explanation of all the menu items.
You can modify printer settings by:
Understanding the operator panel

To select a new value as a setting:
1 From a Ready status message, press Menu. The menu names appear.
2 Continue to press and release Menu until you see the menu you need.
3 Press Select to select the menu or menu item displayed on the second line of the display.
Each menu item has a list of values for the menu item. A value can be:
4 Press Menu to move to the value you need.
5 Press Select to select the value on the second line of the operator panel. An asterisk appears beside the value to indicate that it is now the user default setting. The new setting appears for one second, clears, displays the word Saved, and then displays the previous list of menu items.
6 Press Return to go back to previous menus. Make additional menu selections to set new default settings. Press Go if this is the last setting to change.
User default settings remain in effect until you save new settings or restore the factory defaults. Settings you choose from your software program can also change or override the user default settings you select from the operator panel.
Complete the following steps to print a list of the current user default settings and installed printer options:
1 Make sure the printer power is on and the Ready status message appears.
2 Press Menu until you see Utilities Menu, and then press Select.
3 Press Menu until you see Print Menus, and then press Select.
The message Printing Menu Settings appears and remains until the page prints. The printer returns to Ready when the page or pages finish printing.
If a message appears, see Understanding printer messages for more information.
Understanding the operator panel

4 Verify that the options you installed are correctly listed under “Installed Features.”
If an option you installed is not listed, turn the printer off, unplug the power cord, and reinstall the option.
non-ground fault interrupter (GFI) circuit.
5 Verify the amount of memory installed is correctly listed under “Printer Information.”
6 Verify that the paper trays are configured for the sizes and types of paper you loaded.
The diagram in Using printer menus shows the menu items in each menu.
An asterisk (*) next to a value indicates the factory default setting. Factory defaults may differ for different countries/regions.
Factory defaults are the function settings in effect the first time you turn your printer on. These remain in effect until you change them. Factory defaults are restored if you select the Restore value for the Factory Defaults menu item in the Utilities menu.
When you select a new setting from the operator panel, the asterisk moves next to the selected setting to identify it as the current user default.
User defaults are the settings you select for different printer functions and store in printer memory. Once stored, these settings remain active until new ones are stored or the factory defaults are restored. See Changing printer settings.
select from the operator panel.
If your printer is configured as a network printer available to a number of users, Menus Disabled may appear when you press Menu from the Ready state. Disabling the menus prevents users from using the operator panel to inadvertently change a printer default that has been set by the person managing the printer. You can still use Print and Hold features, clear messages, and select items from the Job menu when printing a job, but you cannot change other printer settings. You can, however, use your printer driver to override printer defaults and select settings for individual print jobs.
1 Open the file you want to print.
2 From the File menu, choose Print.
3 Verify that the correct printer is selected in the dialog box.
Sending a job to print

4 Adjust the printer settings according to your need.
The printer settings available are determined by the program that opens your file.
screen, and then click OK.
5 Click OK or Print to send the job to the selected printer.
1 Press Menu.
Job Menu appears on the first line of the display and Cancel Job appears on the second line.
2 Press Select.
Canceling Job briefly appears on the display. The printer finishes printing any page already being printed, and then stops. The printer returns to the Ready state.
The printer lets you know when you need to load paper. If a tray has less than 50 sheets of paper, Tray x Low appears on the display, where x corresponds to a paper tray. Open the tray and load paper to remove the message.
When you change the paper in the tray, make sure the paper guides are in the correct positions. The position of the left paper guide informs the printer of the size of paper loaded in the tray. Feeding paper when the left or front paper guides are not in the correct position may result in misfeeds or paper jams.
If you load a different type of media, see how to change the Paper Type setting in the Paper Menu.
Canceling a print job

Loading paper
Complete these instructions to load print materials into any of the standard or optional trays.
1 Pull the paper tray out until it stops.
2 Press the metal plate down until it locks.
Loading paper

3 Release the left paper guide by squeezing it and sliding it into the position for the size of paper you are loading.
If the left paper guide is in the wrong position, you may experience paper feeding problems or incorrect page formatting.
4 Flex the sheets back and forth to loosen them, and then fan them.
Do not fold or crease the paper. Straighten the edges of the stack on a level surface.
Loading paper

5 Place the paper in the tray, print side down.
stack height table on the Quick Reference sheet or in the Media guidelines. Overfilling the tray may cause jams.
6 Squeeze the front paper guide lever and slide the guide until it lightly touches the stack of paper. Make sure the left paper guide is positioned snugly against the stack of paper. If necessary, squeeze and slide the left paper guide until it latches into place against the paper stack.
Loading paper

7 Rotate the paper size dial until the size of the paper in the tray is indicated.
the printer.
8 Push the tray in.
See Loading the multipurpose feeder for instructions on loading letterhead in the multipurpose feeder.
only be fed from the optional Heavy Media Tray. Glossy paper can be fed from any tray.
Loading other paper sizes

Loading the multipurpose feeder
The multipurpose feeder can hold several sizes and types of paper, such as transparencies and envelopes. It is useful for single page printing on letterhead, colored paper, or other specialty media. Refer to the Card Stock & Label Guide for more information on paper types and sizes.
You can use the multipurpose feeder one of two ways:
Keep in mind the following capacities, paper dimensions, and operating tips when loading the multipurpose feeder.
The maximum stack height is 11 mm (0.4 in.). The multipurpose feeder can hold approximately:
The multipurpose feeder accepts paper within the following dimensions:
Loading the multipurpose feeder

To load the multipurpose feeder:
1 Open the multipurpose feeder, and then extend the recessed tray to accommodate the paper you want to use.
2 Slide the paper width guides to the correct position.
Loading the multipurpose feeder

3 Push down the bottom plate until it locks into place.
4 Prepare the print media for loading.
5 Load one type of print media in the multipurpose feeder. Do not mix types. Click a topic for loading instructions:
Loading the multipurpose feeder

a Load paper, transparencies, labels, and card stock in the center of the tray with the recommended print side face up.

b Continue with step 6.
a Load envelopes flap side down, with the flap closed, and with the return address area on the right. Orient the envelopes so that the edge with the return address and stamp area will enter the multipurpose feeder last.
stick adhesives. These envelopes may severely damage the printer.

multipurpose feeder.
b Continue with step 6.
Loading the multipurpose feeder

Loading letterhead
a For both simplex (single-sided) and duplex (double-sided) printing on letterhead, place the printed side face up.
b Continue with step 6.
6 Gently slide the print media into the multipurpose feeder.
7 Slide the width guides until they lightly rest against the edges of the print media. Do not bend the print media.

8 Push the SET button to the left to unlock the bottom plate.

Loading the multipurpose feeder

9 Select the paper source, size, and type from your software program and select paper size and type from the operator panel.
a Make sure the paper size (MP Feeder Size) and paper type (MP Feeder Type) for the multipurpose feeder are set to the correct value for the print media you are loading. (See Paper and Paper Type for detailed information about these settings.)
b Press Go to return to Ready.
1 Remove print media from the multipurpose feeder.
2 Push the extended tray in to collapse the multipurpose feeder to its short-length position.
3 Push down the bottom plate until it locks into place.
Loading the multipurpose feeder

4 Close the multipurpose feeder.
Loading the multipurpose feeder

Using the Print and Hold function
When sending a job to the printer, you can specify in the driver that you want the printer to hold the job in memory. When you are ready to print the job, you must go to the printer and use the operator panel menus to identify which held job you want to print.
Once held jobs are stored in printer memory, you can use the operator panel to specify what you want to do with one or more of the jobs. You can select either Confidential Job or Held Jobs (Repeat Print, Reserve Print, and Verify Print jobs) from the Job Menu. If you select Confidential Job, you must enter the personal identification number (PIN) you specified in the driver when you sent the job. See Printing confidential jobs for more information.
From either the Confidential Job or the Held Jobs menu items, you have five choices:
1 To access held jobs from the operator panel:
2 Press Menu until you see Held Jobs or Confidential Job on the operator panel display, depending on the type of job you want to access.
3 Press Select.
Printing confidential jobs for more information.
4 Press Menu until the action you want to take appears on the second line of the operator panel (print a job, delete a job, and so on).
5 Press Select.
Using the Print and Hold function

6 Press Go to print or delete specific jobs you have marked.
The printer briefly displays messages indicating what Print and Hold functions it is performing, and then returns to the Ready state.
If the symbol appears on the display, it indicates that the printer had trouble formatting one or more of the held jobs. These formatting problems are most commonly the result of insufficient printer memory or invalid data that might cause the printer to flush the job.
When a symbol appears next to a held job, you can:
If formatting errors are a recurring problem with held jobs, your printer may require more memory.
If you send a Repeat Print job, the printer prints all requested copies of the job and stores the job in memory so you can print additional copies later. You can print additional copies as long as the job remains stored in memory.
requires extra memory to process additional held jobs.
If you send a Reserve Print job, the printer does not print the job immediately, but stores the job in memory so you can print the job later. The job is held in memory until you delete it from the Held Jobs menu. Reserve Print jobs may be deleted if the printer requires extra memory to process additional held jobs.
See Printing and deleting held jobs.
If you send a Verify Print job, the printer prints one copy and holds the remaining copies you requested from the driver in printer memory. Use Verify Print to examine the first copy to see if it is satisfactory before printing the remaining copies.
See Printing and deleting held jobs if you need help printing the additional copies stored in memory.
Using the Print and Hold function

Printing confidential jobs
When you send a job to the printer, you can enter a personal identification number (PIN) from the driver. The PIN must be four digits using the numbers 1–6. The job is then held in printer memory until you enter the same four-digit PIN from the operator panel and choose to print or delete the job. This ensures that the job does not print until you are there to retrieve it, and no one else using the printer can print the job.
Select Confidential Job from the Job Menu and then select your user name. The following prompt is displayed:
Use the buttons on the operator panel to enter the four-digit PIN associated with your confidential job. The numbers next to the button names identify which button to press for each digit (1–6). As you enter the PIN, asterisks are displayed on the operator panel to ensure confidentiality.
=****
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
If you enter an invalid PIN, the message No Jobs Found. Retry? appears. Press Go to re-enter the PIN, or press Stop to exit the Confidential Job menu.
When you enter a valid PIN, you have access to all print jobs matching the user name and PIN you entered. The print jobs matching the PIN you entered appear on the display when you enter the Print A Job, Delete A Job, and Print Copies menu items. You can then choose to print or delete jobs matching the PIN you entered. (See Printing and deleting held jobs for more information.) After printing the job, the printer deletes the confidential job from memory.
Printing confidential jobs

Printing with custom size specialty media
Your printer supports a wide range of paper sizes and types, some of which exceed the dimensions of your printer’s standard trays. As a result, when printing with media of a special size you must first make the appropriate adjustments to both your printer and your printer’s driver.
Because some sizes of media do not fit in your printer’s normal paper trays, you must use the multipurpose feeder to load the media into your printer.
For detailed instructions on loading custom size media, see Loading the multipurpose feeder.
The Universal paper size is the standard setting for custom size media on your printer, using 12x18 in. as the default dimensions. If you have changed the default settings on your printer or you want to use media of a different size, you must set the Universal paper size to the dimensions that you want to use and make sure that the appropriate unit of measure is selected.
1 Press Return until you see the main menu.
2 Press Menu until you see Paper Menu, and then press Select.
3 Press Menu until you see Universal Setup, and then press Select.
4 Press Menu until you see Portrait Width, and then press Select.
5 Press Menu until you see Portrait Height, and then press Select.
1 From Universal Setup, press Menu until you see Units of Measure, then press Select.
2 Press Menu until the appropriate unit of measure is displayed. If the unit of measure you want is already saved with an asterisk beside it, press Return to return to Universal Setup. Otherwise, press Select to change the unit of measure.
Printing with custom size specialty media

Once the Universal paper size is set, you must designate Universal as the paper size for the multipurpose feeder.
designation.
Press Return until you see the main menu.
Press Menu until you see Paper Menu, then press Select.
Press Menu until you see Paper Size, then press Select.
Press Menu until you see MP Feeder Size, and then press Select.
Press Menu until you see Universal, then press Select.
Press Return until you see Ready.
If MP Feeder Size is not listed as an option under the Paper Size menu, then you must set the Configure MP menu option to Cassette. The Configure MP menu is located in the Paper Menu.
1 Press Return until you see the main menu.
2 Press Menu until you see Paper Menu., then press Select.
3 Press Menu until you see Paper Source, and then press Select.
4 Press Menu until you see MP Feeder, and then press Select.
5 Press Return until you see Ready.
Now that you have configured your printer’s operator panel, you must configure your printer’s driver on your computer.
1 In your computer, go to Start Settings Control Panel.
2 Double-click the Printers folder and highlight your printer in the list by clicking it once, then select File Properties.
3 Select the Paper tab, and then click User Forms.
4 In the Form Type field, enter the name of the custom form you are defining.
Printing with custom size specialty media

5 Under Form Size, enter the form’s dimensions in the fields for Width and Length. In the case of 12x18 in. paper, you would enter 12.0 under Width and 18.0 under Length.
6 Specify the appropriate units of measurement.
7 Click the Add button to add the form to the Defined User Forms list, and then click OK to return to Printer Properties.
8 In Properties, under the Paper tab, make sure that your new custom form is displayed in the Form Type field.
9 Open your program and print your document.
1 In your computer, go to Start Settings Control Panel.
2 Double-click the Printers folder and highlight your printer in the list by clicking it once, then select File Properties.
3 Click the Paper tab. Under Custom Forms, click New Size.
4 Enter the name of the custom form you are defining.
5 Specify the form type as Paper.
6 Specify the appropriate units of measurement.
7 Enter the appropriate dimensions for Width and Length.
8 Click OK to define the form and return to Printer Properties.
9 In Properties, under the Paper tab, make sure that your new custom form is displayed in the Form Size field.
10 Open your program and print your document.
1 In your computer, go to Start Settings Control Panel. For Windows XP and Windows XP Professional, go to Start Control Panel.
2 Go to the Printers folder, and select File Server Properties. For Windows XP and Windows XP Professional, go to Printers and Other Hardware and select Printers and Faxes. Select File Server Properties.
3 Select the Forms tab, and then click the Create a new form box.
4 In the Form Description For field, enter a name for the custom form that you are defining. For example, enter Custom 12x18 in.
5 Under Measurements, enter the appropriate dimensions and margins for the form, as well as the units of measurement, Click Save Form to add the new form.
6 Click OK to return to the Printers folder.
Printing with custom size specialty media

7 For Windows 2000 and XP, in the Printers folder, highlight your printer by clicking it once. Go to File Printing Preferences.
8 In Printing Preferences, select the Paper tab.
9 For PostScript drivers for Windows 2000 and XP, select your custom form from the list under Form Type.
For PCL Drivers for Windows 2000 and XP, select your custom form from the list under Form Size.
10 Open your program and print your document.
1 Verify that your desktop printer is the default printer.
2 In your program, go to File Page Setup.
3 Click the Page Setup menu, and then select Custom Page Sizes. Click New.
4 Enter a name for your custom page under the Custom Page Size Name edit box.
5 Under Paper Size, enter the appropriate dimensions. Under Margins, enter the appropriate margin size.
6 Select the appropriate units of measure.
7 Click OK.
8 In your program, go to File Page Setup. Click the Page Setup menu, and then select Page Attributes. Under Paper, select the custom size you want to use.
9 Print your document.
Printing with custom size specialty media

For Mac OS X v10.2:
In your program, go to File Page Setup.
Under Format for, select the Any Printer option.
Under Settings, select Custom Paper Size, and then click New.
Enter the name for your custom paper size.
Enter the appropriate dimensions and margins.
Click Save.
Click OK.
In your program, go to File Page Setup.
Under Format for, make sure that the Any Printer option is selected.
Under Paper Size, select the custom size you want to use.
Print your document.
Printing with custom size specialty media

Tips for successful printing
Storing print media
Properly storing the media helps ensure trouble-free printing. Use the following guidelines:
° • For best results, store media in an environment where the temperature is approximately 21 C
By carefully selecting print media and loading them properly, you should be able to avoid most paper jams. If jams do occur, follow the steps outlined in Clearing paper jams. If jams occur frequently, make sure you follow these tips to avoid jams:

Understanding fonts
Resident fonts
Your printer is equipped with resident fonts stored permanently in printer memory. Different fonts are available in PCL 6 and PostScript 3 emulations. Some of the most popular typefaces, like Courier and Times New Roman, are available for all printer languages.
The fonts in the PCL emulation are compatible with the fonts in the HP4500 and include four additional fonts and many extra symbol sets to support extra languages and programs. The fonts in the PostScript emulation are compatible with Adobe PostScript 3 and include 20 additional fonts.
The following tables list all the fonts in your printer. You can select the resident fonts from your software program, or from the operator panel if you are using PCL 6 emulation.
PCL 6 emulation PostScript 3 emulation
Antique Olive Italic AntiqueOlive-Italic
Antique Olive Bold AntiqueOlive-Bold
Arial Bold Italic Arial-BoldItalicMT
ITC Avant Garde Book AvantGarde-Book
ITC Avant Garde Book Oblique AvantGarde-BookOblique
ITC Avant Garde Demi AvantGarde-Demi
ITC Avant Garde Demi Oblique AvantGarde-DemiOblique
ITC Bookman Light Bookman-Light
ITC Bookman Light Italic Bookman-LightItalic
ITC Bookman Demi Bookman-Demi
ITC Bookman Demi Italic Bookman-DemiItalic

PCL 6 emulation PostScript 3 emulation
CourierPS Bold Oblique Courier-BoldOblique
CG Omega Bold Italic
Garamond Kursiv Halbfett Garamond-KursivHalbfett
Helvetica Light Oblique Helvetica-LightOblique
Helvetica Black Oblique Helvetica-BlackOblique
Helvetica Bold Italic Helvetica-BoldOblique
Helvetica Narrow Italic Helvetica-Narrow-Oblique
Helvetica Narrow Bold Helvetica-Narrow-Bold
Helvetica Narrow Bold Italic Helvetica-Narrow-BoldOblique
CG Times Italic Intl-CG-Times-Italic
CG Times Bold Intl-CG-Times-Bold
CG Times Bold Italic Intl-CG-Times-BoldItalic
Univers Medium Italic Intl-Univers-MediumItalic
Univers Bold Italic Intl-Univers-BoldItalic

PCL 6 emulation PostScript 3 emulation
Courier Bold Italic Intl-Courier-BoldOblique
Letter Gothic Italic LetterGothic-Slanted
Letter Gothic Bold LetterGothic-Bold
Century Schoolbook Roman NewCenturySchlbk-Roman
Century Schoolbook Italic NewCenturySchlbk-Italic
Century Schoolbook Bold NewCenturySchlbk-Bold
Century Schoolbook Bold Italic NewCenturySchlbk-BoldItalic
Palatino Bold Italic Palatino-BoldItalic
Times Bold Italic Times-BoldItalic
Times New Roman TimesNewRomanPSMT
Times New Roman Italic TimesNewRomanPS-ItalicMT
Times New Roman Bold TimesNewRomanPS-BoldMT
Times New Roman Bold Italic TimesNewRomanPS-BoldItalicMT
Univers Condensed Medium Univers-Condensed

PCL 6 emulation PostScript 3 emulation
Univers Condensed Medium Italic Univers-CondensedOblique
Univers Condensed Bold Univers-CondensedBold
Univers Condensed Bold Italic Univers-CondensedBoldOblique
ITC Zapf Chancery Medium Italic ZapfChancery-MediumItalic
ITC Zapf Dingbats ZapfDingbats

PCL 6 emulation PostScript 3 emulation

PCL 6 emulation PostScript 3 emulation
PCL 6 emulation PostScript 3 emulation
A symbol set is an encoded collection of alphabetic and numeric characters, punctuation, and special characters available in the font you select. Symbol sets support the requirements for different languages or specific programs, such as math symbols used for scientific text.
The symbol set encoding also defines which character will print for each key on the keyboard (or more specifically, for each code point). Some programs require different characters at some code points. To support multiple programs and languages, your printer has 83 symbol sets for the resident PCL 6 emulation fonts.
Not all fonts support all of the symbol sets listed in Downloadable fonts. Refer to the Technical Reference to determine which symbol sets are supported by each font name.

Downloadable fonts
ABICOMP International POSTNET Bar code ISO 57: Chinese
PCL ITC Zapf Dingbats ISO 11: Swedish for Names ISO 8859-2 Latin 2
PS ITC Zapf Dingbats ISO 14: JIS ASCII ISO 8859-5 Latin/Cyrillic
PC-8 Bulgarian PC-857 Latin 5 (Turkish) Roman-9
PC-8 Danish/Norwegian PC-858 Multilingual Euro Roman Extension (437N)
PC-8 Greek Alternate (437G) PC-860 Portuguese Ventura ITC Zapf Dingbats
PC-8 Turkish (437T) PC-861 Icelandic Ventura International
PC-8 Latin/Greek PC-863 Canadian French Ventura Math
PC-8 PC Nova PC-865 Nordic Ventura US
PC-8 Polish Mazovia PC-866 Cyrillic Windows 3.0 Latin 1
PC-8 Code Page 437 PC-869 Greek Windows 98 Cyrillic
PC-775 Baltic (PC-8 Latin 6) PC-911 Katakana Windows 98 Greek
PC-850 Multilingual PC-1004 OS/2 Windows 98 Latin 1
PC-851 Greek Math-8 Windows 98 Latin 2
PC-852 Latin 2 Greek-8 Windows 98 Latin 5
PC-853 Latin 3 (Turkish) Turkish-8 Windows 98 Latin 6 (Baltic)
You can download scalable fonts in PostScript 3 emulation and either scalable or bit mapped fonts in PCL 6 emulation. Fonts can be downloaded to printer memory, or to a flash memory option or hard disk option. Fonts downloaded to flash memory or hard disk remain in memory even after the printer language changes, the printer resets, or the printer is turned off.
PC-855 Cyrillic Roman-8 · Understanding fonts

Euro support
Support for the euro currency character is included in all applicable fonts for both the PostScript and PCL emulations. Twelve of the PCL symbol sets support the euro character, including all seven Windows symbol sets.
A variety of downloadable fonts for Hebrew and Arabic are included on the CD that shipped with the printer.
Also included on the CD is the FontVision™ Management utility and screen fonts to match the resident scalable fonts. An additional 48 TrueType fonts are available on the Lexmark Web site when you register the printer.
Understanding fonts

Use recommended media (paper, transparencies, envelopes, card stock and labels) for your printer to avoid printing problems.For detailed information about media characteristics, refer to the Card Stock & Label Guide located on the Lexmark Web site at www.lexmark.com. Brief guidelines for choosing paper and other media follow.
Source Paper sizes Paper types Capacity
Tray 1 Letter, A4, Legal, Tabloid 1, A3, JIS B4
Paper, glossy paper 550 sheets of 20 lb paper
200 sheets of 24 lb legal, tabloid, A3 or JIS B4 paper
130 sheets of glossy paper
Trays 2-4 Letter, A4, Legal, Tabloid 1, A3, JIS B4
Paper 550 sheets of 20 lb paper
200 sheets of 24 lb legal, tabloid, A3 or JIS B4 paper
Letter, A4, A5, Legal, Tabloid1, A3, JIS B4
Paper, glossy paper, transparencies, labels
300 sheets of 32 lb paper
200 sheets of labels
360 sheets of glossy paper
Letter, A4, A5, Legal, Tabloid 1 , A3, Executive, JIS B4, JIS B5, 12x18, Banner 2, 3, Universal 4, 5
Paper, glossy paper, transparencies, labels, card stock
100 sheets of 20 lb paper
55 sheets of labels
55 sheets card stock
80 sheets of 24 lb 12x18 paper
1 sheet of glossy paper
1 sheet of banner paper
7¾, 9, 10, DL, C4, C5, B5 Envelopes 10 envelopes
Letter, A4 Paper 3000 sheets of 20 lb paper
1 Tabloid paper is 278.8 x 430.8 mm (11 x 17 in.) 2 Banner size is a Universal size: 297.2 x 914.4 mm (11.69 x 36 in.) 3 Banner paper is not supported on custom Windows 9x PCL and Windows NT 4.0 system printer drivers.
4 Universal setting lets you select the following custom sizes: – 70 x 127 mm to 229 x 356 mm (2.8 x 5 to 9 x 14 in.) – 148 x 182 mm to 216 x 356 mm (5.8 x 7 to 8.5 x 14 in.) – 304.8 x 457.2 mm (12 x 18 in.) – 210 x 432 mm to 297 x 914 mm (8.3 x 17 to 11.69 x 36 in.) 5 Universal size paper must be fed from the multipurpose feeder; no other input tray supports Universal.

Your printer supports a wide variety of paper types, sizes, and weights. The standard tray (tray 1) and optional trays 2, 3, and 4 are marked with stack height letters A, B, C. The optional heavy media tray is marked with stack height letters D, E, and F.
For detailed information about media characteristics, refer to the Card Stock and Label Guide located on the Lexmark Web site at www.lexmark.com
The following table lists recommended media, weights, and the stack height guide to use when loading the paper trays.
Stack height letter Recommended media
B 11x17, Legal, B4, A3 (90–105 g/m2, 24–28 lb bond)
C Letter, A4 (60–105 g/m2 , 16–28 lb bond)
11x17, Legal, B4, A3 (60–90 g/m2, 16 - 24 lb bond)
F Letter, A4 (105–128 g/m2, 28–34 lb bond)
* Lexmark Glossy Paper is 120 g/m2, 80 lb. book, 32 lb bond.
** Lexmark Transparency weight is 170 g/m2 .
print quality.
When printing photographic quality images, use a high-quality laser printer paper. We recommend the following paper for optimum results:
Paper Weight Size Part Number
Hammermill Laser Print 90 g/m2 (24 lb) Letter
12A5951 Lexmark Glossy Laser Paper 120 g/m2 (32 lb)
For printing text and typical business graphics, you may find 75 g/m2 (20 lb) paper designed for laser printers or photocopiers produces acceptable print quality. Always try a sample of any paper before buying large quantities.
Before loading paper, note the recommended print side identified on the paper package. Load paper with the recommended print side face down in the paper trays. For paper loading instructions, see Loading a paper tray.
Paper

The following are not recommended for your printer:
Preprinted papers such as letterhead must be able to withstand temperatures of up to 180°C (356°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner or the silicone in the fuser. Inks that are oxidation-set or oil-based should meet these requirements. Latex inks may melt.
The duplex option does not support Cardstock, Transparencies, Labels, or Envelopes.
Orientation Paper Size Weight
(20 – 28 lbs.)
JIS-B5

Transparencies
For best results, use the following Lexmark transparencies:
Description Size Part number
Professional color laser transparencies Letter 12A5940
These transparencies are designed to provide optimal print quality. Using other transparencies designed for laser printers may yield unpredictable results and possibly cause damage to your printer.
Transparencies must be able to withstand temperatures of up to 180°C (356°F) without melting, discoloring, offsetting, or releasing hazardous emissions.
To order transparencies in the U.S., call 1-800-438-2468. In other countries/regions, visit www.lexmark.com on the World Wide Web.
For transparency loading instructions, see Loading paper.
You can load up to 10 envelopes in the multipurpose feeder. Load envelopes flap side down, with the flap closed, and with the return address area on the right. Orient the envelopes so that the edge with the return address and stamp area will enter the multipurpose feeder last. Do not load stamped envelopes. Before loading envelopes, fan the stack to prevent them from sticking together. For envelope loading instructions, see Loading envelopes.
To ensure the best print quality, set Paper Type (or Media Type in the driver) to Envelope and select the correct envelope size before sending the job to print
When printing on envelopes:
Transparencies

Use only labels designed for laser printers. Use only label sheets that have no gaps between the labels, as shown. Try a sample of any labels before purchasing a large quantity.
Acceptable labels Unacceptable labels
Labels must be able to withstand temperatures of 180°C (356°F) without melting, discoloring, offsetting, or releasing hazardous emissions. For detailed information on label printing, characteristics, and design, refer to the Card Stock & Label Guide available on Lexmark’s Web site.
Feed labels only from the multipurpose feeder. When printing on labels:
For label loading instructions, see Loading paper.
Load card stock in the multipurpose feeder only. Using the wrong paper source may cause paper jams or a failure to feed. The properties of the card stock—such as the orientation of the paper fibers, moisture content, thickness, and texture can affect the print quality.
For optimum results, we recommend using Springhill Index Plus 90 lb index card stock.
Card stock must be able to withstand temperatures up to 180°C (356°F) without melting or releasing hazardous emissions.
For more information on card stock your printer supports, refer to the Card Stock & Label Guide available on Lexmark’s Web site.
Always set the Paper Type (or Media Type) to Card Stock when printing on heavier paper. The printer then adjusts the fuser temperature and engine speed to ensure the best print quality.
For card stock loading instructions, see Loading paper.
Labels

Card stock


Select a menu or menu item for more details.
Supplies Menu Toner Color Photo Devs Black Photo Dev Fuser Belt Supplies Life Replace Supplies
Job Menu Reset Printer Cancel Job Cancel Fax Confidential Job Held Jobs Reset Active Bin Prime Stapler
PCL Emul Menu Font Source Font Name Point Size Pitch Symbol Set Orientation Lines per Page A4 Width Auto CR after LF Auto LF after CR Tray Renumber
Serial Menu PCL SmartSwitch PS SmartSwitch NPA Mode Serial Buffer Job Buffering Serial Protocol Robust XON Baud Data Bits Parity RS-232/RS-422 RS-422 Polarity Honor DSR
Color Menu Color Correction Manual Color Print Mode Toner Darkness
USB Menu PCL SmartSwitch PS SmartSwitch MAC Binary PS NPA Mode USB Buffer Job Buffering Paper Menu Paper Source Paper Size Paper Type Custom Types Output Bin Configure Bins Assign Type/ Bin Substitute Size Configure MP Paper Weight Paper Loading Universal Setup
Finishing Menu Copies Duplex Duplex Bind Blank Pages Collation Separator Sheets Separator Source Hole Punch Offset Pages Staple Job Staple Prime Src Multipage Print Multipage Order Multipage View Multipage Border
Network Menu PCL SmartSwitch PS SmartSwitch MAC Binary PS NPA Mode Network Buffer Job Buffering Network Setup Std Net Setup
Setup Menu Printer Language Printer Usage Power Saver Resource Save Download Target Print Timeout Auto Continue Wait Timeout Jam Recovery Page Protect Display Language Alarm Control Hole Punch Alarm Staple Alarm Job Accounting Start Page
Utilities Menu Print Menus Print Net Setup Print Fonts Print Directory Print Demo Color Samples Factory Defaults Remove Held Jobs Format Flash Defragment Flash Format Disk Job Acct Stat Hex Trace Print Alignment
Parallel Menu PCL SmartSwitch PS SmartSwitch NPA Mode Parallel Buffer Job Buffering Advanced Status Protocol Honor Init Parallel Mode 1 Parallel Mode 2 MAC Binary PS
Infrared Menu Infrared Port PCL SmartSwitch PS SmartSwitch NPA Mode Infrared Buffer Job Buffering Window Size Transmit Delay Max Baud Rate
Fax Menu Fax Setup Fax Logs Fax Send Fax Receive
PostScript Menu Print PS Error Font Priority Image Smoothing
Using printer menus

Disabling operator panel menus
To disable the operator panel menus so that changes cannot be made to the printer default settings:
1 Turn the printer off.
the Print and Hold function.
2 Press and hold Select and Return and turn the printer on.
3 Release the buttons when you see Performing Self Test.
Config Menu appears on the first line of the display.
4 Press Menu until you see Panel Menus, and then press Select.
5 Press the menu keys until Disable appears on the second line of the display.
6 Press Select.
Disabling Menus appears briefly.
7 Press Menu until you see Exit Config Menus, and then press Select.
The menus are disabled. If you press Menu, the message Menus Disabled appears.
1 Repeat steps 1 through 4.
2 Press Menu until you see Enable.
3 Continue with steps 5, 6, and 7.
Disabling operator panel menus

Color Menu
Use the Color Menu to adjust print quality and customize color printing.
Menu Item Purpose Values
To adjust the printed color to better match the colors of other output devices or standard color systems.
Auto* Applies different color conversion tables to each object on the printed page depending upon the type of object and how the color for each object is specified.
Off No color correction is implemented.
Manual Lets you customize the color conversion tables applied to each object on the printed page depending upon the type of object and how the color for each object is specified. Customization is performed using the selections available under the Manual Color menu item.
Color Correction · Color Menu

Menu Item Purpose Values
Manual Color To let users customize the RGB or
CMYK color conversions applied to each object on the printed page. Color conversion of the data specified using RGB combinations can be customized based on object type (text, graphics, or image).
Print Mode To determine whether images are printed in a monochrome grayscale or in color.

Menu Item Purpose Values
To lighten or darken printed output, or conserve toner.
5 If Print Mode is Black & White, a setting of 5 increases toner density and darkness to all print jobs (PCL or PostScript). If Print Mode is Color, a setting of 5 is the same as 4.
4* Default toner darkness setting.
3 Reduction in toner consumption.
2 Further reduction in toner consumption.
1 Maximum reduction in toner consumption.
Use the Finishing Menu to define how the printer delivers the printed output.
Menu Item Purpose Values
Blank Pages To specify whether to include program-generated blank pages as part of your printed output.
Do Not Print* Does not print program-generated
blank pages as part of your job.
Print Prints program-generated blank pages as part of your job.
Collation To keep the pages of a print job stacked in sequence when printing multiple copies of the job.
Off* Prints each page of a job the number of times specified by the Copies menu item. For example, if you set Copies to 2 and send three pages to print, the printer prints page 1, page 1, page 2, page 2, page 3, page 3.
On Prints entire job the number of times specified by the Copies menu item. For example, if you set Copies to 2 and send three pages to print, the printer prints page 1, page 2, page 3, page 1, page 2, page 3.
Copies To set the number of copies you want for the printer default value. (Set the number of copies required for a specific job from the printer driver. Values selected from the printer driver always override values selected from the operator panel.)
1...999 (1*)
Toner Darkness · Finishing Menu

Menu Item Purpose Values
Duplex To set duplexing as the default for all print jobs. (Select Duplex from the printer driver to duplex only specific jobs.)
Off* Prints on one side of the paper.
On Prints on both sides of the paper.
Duplex Bind To define the way duplexed pages are bound, and how the printing on the back of the sheet (even- numbered pages) is oriented in relation to the printing on the front (odd-numbered pages).
Long Edge* Assumes binding along the long end of the page (left edge for portrait orientation and top edge for landscape orientation).
Short Edge Assumes binding along the short edge of the page (top edge for portrait orientation and left edge for landscape orientation).
Hole Punch To punch holes along the edge of all printed output. (Select Hole Punch from the printer driver to punch holes only in output for a specific job.)
Off* Does not punch holes in printed output.
On Punches holes in every printed page.
To print a border around each page image when using Multipage Print.
None* Does not print a border around each page image.
Solid Prints a solid line border around each page image.
To determine the positioning of multiple page images when using Multipage Print. The positioning depends on the number of images and whether the images are portrait or landscape in orientation.
For example, if you select 4-Up multipage printing and portrait orientation, the results differ depending on the Multipage Order value you select:
Horizontal Vertical Order Reverse Vertical Order Reverse Horizontal

Menu Item Purpose Values
To print multiple page images on one side of a sheet of paper. Also called n-up or Paper Saver.
Off* Prints one page image per side.
2 Up Prints two page images per side.
3 Up Prints three page images per side.
4 Up Prints four page images per side.
6 Up Prints six page images per side.
9 Up Prints nine page images per side.
12 Up Prints twelve page images per side.
16 Up Prints sixteen page images per side.
To determine the orientation of a multipage sheet.
Auto* Lets the printer choose between portrait and landscape orientation.
Long Edge Sets the long edge of the paper as the top of the page (landscape).
Short Edge Sets the short edge of the paper as the top of the page (portrait).
Offset Pages To offset the output of each print job or each copy of a print job, making it easier to separate the documents stacked in the output bin.
None* Stacks all sheets directly on top of each other.
Offsets each copy of a print job.
Offsets each print job.
To insert blank separator sheets between jobs, between multiple copies of a job, or between each page of a job.
None* Does not insert separator sheets.
Inserts a blank sheet between each copy of a job. If Collation is Off, a blank page is inserted between each set of printed pages (all page 1’s, all page 2’s, and so on). If Collation is On, a blank page is inserted between each collated copy of the job.
Inserts a blank sheet between jobs.
Inserts a blank sheet between each page of a job. This is useful if you are printing transparencies or want to insert blank pages in a document for notes.
To specify the paper source that holds separator sheets.
Tray <x> (Tray 1*)
Selects separator sheets from the specified tray.
MP Feeder Selects separator sheets from the multipurpose feeder. (You must also set Configure MP to Cassette.)

Menu Item Purpose Values
Staple Job To set stapling as the default for all print jobs. (Select stapling from the printer driver if you want to staple only specific jobs.)
Off* Does not staple print jobs.
On Staples each print job sent to the printer.
To specify the paper source you want the printer to use when it primes the stapler. When a staple cartridge is replaced or a staple jam is cleared, the printer may need to prime the stapler by stapling a sheet of paper several times.
Tray <x> (Tray 1*)
Selects paper from the specified tray.
MP Feeder Selects paper from the multipurpose feeder.
The Infrared Menu is only displayed when at least one infrared interface exists on the printer.
Infrared Port Whenever the value of the NPA Mode, Infrared Port, or Job Buffering is changed from the operator panel, the printer automatically restarts upon exiting the menus in order to reconfigure memory.
PCL SmartSwitch Note: Only displayed when both PCL and PostScript interpreters are available AND Infrared Port is not set to Disabled.
PS SmartSwitch Note: Only displayed when both PCL and PostScript interpreters are available AND Infrared Port is not set to Disabled.
NPA Mode Whenever the value of the NPA Mode, Infrared Port, or Job Buffering is changed from the operator panel, the printer automatically restarts upon exiting the menus in order to reconfigure memory.

Infrared Buffer Whenever the value of the NPA Mode, Infrared Port, or Job Buffering is changed from the operator panel, the printer automatically restarts upon exiting the menus in order to reconfigure memory.
=36 K ... (max size allowed)
Job Buffering Whenever the value of the NPA Mode, Infrared Port, or Job Buffering is changed from the operator panel, the printer automatically restarts upon exiting the menus in order to reconfigure memory.
Window Size Note: Only displayed when Infrared Port is not set to Disabled.
Transmit Delay Note: Only displayed when Infrared Port is not set to Disabled.
=1...15
Max Baud Rate Note: Only displayed when Infrared Port is not set to Disabled.

Job Menu
The Job Menu is only available when the printer is busy processing or printing a job, when a printer message is displayed, or when the printer is in Hex Trace mode. Press Menu to open the Job Menu.
Menu Item Purpose Values
Cancel Fax To cancel outgoing faxes before they are transmitted or to cancel incoming faxes before they finish printing.
R Cancels an incoming fax. When the fax number for the sending machine is displayed, press Select to cancel the incoming fax.
D Cancels an outgoing fax. When the fax number for the receiving machine is displayed, press Select to cancel the fax job. If the telephone number of the fax you want to cancel is not displayed, use the Menu button to scroll through the list. The printer can display up to five outgoing fax numbers in the outgoing fax queue. When more than five faxes are in the queue, the next fax job that appears on the display as an outgoing fax is transmitted or canceled.
Cancel Job To cancel the current print job. Cancel Job is only displayed if the printer is processing a job or has a job in printer memory.
Job Menu

Menu Item Purpose Values
To print confidential jobs stored in printer memory.
1 Enter the Personal Identification Number (PIN) associated with your confidential job.
Enter PIN Use the operator panel buttons to enter the PIN associated with your confidential job.
PIN.
Print A Job Prints the specified confidential job. Press Menu to scroll through the list of confidential jobs associated with your PIN. Press Select to print a specific job.
Deletes all jobs associated with your PIN.
Delete A Job Deletes the specified confidential job. Press Menu to scroll through the list of Confidential Jobs associated with your PIN. Press Select to delete a specific job.
Copies Determines the number of copies printed for each confidential job. Press Menu to scroll through the list of confidential jobs associated with your PIN. Press Select to specify the job you want to print. Press Menu to increase or decrease the number of copies, and then press Select.
Held Jobs To print Reserve Print, Repeat Print, or Verify Print jobs stored in printer memory.
Print All Jobs Prints all held jobs.
Print A Job Prints the specified held job. Press Menu to scroll through the list of held jobs. Press Select to print the specific job.
Deletes all held jobs.
Delete A Job Deletes the designated held job. Press Menu to scroll through the list of held jobs. Press Select to delete the job.
Copies Determines the number of copies for each held job. Press Menu to scroll through the list of held jobs. Press Select to specify the job you want to print. Press Menu to increase or decrease the number of copies, and then press Select.
To define the active bin as the start bin (the first bin to receive printed output) in a set of linked bins.

Menu Item Purpose Values
The staple priming operation is mostly required when a user loads a new staple cartridge in the stapler device. However, this operation may also be required when a staple jam has occurred as part of the staple jam clearing procedure.
Reset Printer To reset the printer to the user default value for each menu item, delete all downloaded
resources (fonts, macros, and symbol sets) stored in printer memory (RAM), and delete all data in the interface link buffer.
Before selecting Reset Printer, exit the software program you are using.
Use the Network Menu to change printer settings affecting jobs sent to the printer through a network port (either Standard Network or Network Opt ).
Menu Item Purpose Values
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To configure the printer to process Macintosh binary PostScript print jobs.
On Printer processes raw binary PostScript print jobs from computers using the Macintosh operating system.
Off Printer filters PostScript print jobs using standard protocol.
Auto* Printer processes print jobs from computers using either Windows or Macintosh operating systems.
To configure the size of the network input buffer.
Auto* Printer automatically calculates the Network Buffer size (recommended setting).
3K to maximum size allowed
User specifies the Network Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Network Buffer size, disable or reduce the size of the parallel, serial, and USB buffers.

Menu Item Purpose Values
To configure an internal print server.
Values for this menu item are supplied by the specific print server. Select the menu item to see the available values.
NPA Mode To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To configure the printer so it automatically switches to PCL emulation when a print job received through the network port requires it, regardless of the default printer language.
On* Printer examines data on the network interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
To configure the printer so it automatically switches to PostScript emulation when a print job received through the network port requires it, regardless of the default printer language.
On* Printer examines data on the network interface connection and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
To configure an internal print server.
Values for this menu item are supplied by the specific print server. Select the menu item to see the available values.

Parallel Menu
Use the Parallel Menu to change printer settings affecting jobs sent to the printer through a parallel port (either Std Parallel or Parallel Opt ).
Menu Item Purpose Values
To enable bidirectional communication through the parallel port.
Off Disables parallel port negotiation.
On* Enables bidirectional communication through the parallel interface.
Honor Init To determine whether the printer honors hardware initialization requests from the computer. The computer requests initialization by activating the INIT signal on the parallel interface. Many personal computers activate the INIT signal each time the computer is turned on and off.
Off* Printer does not honor hardware initialization requests from the computer.
On Printer honors hardware initialization requests from the computer.
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To configure the printer to process Macintosh binary PostScript print jobs.
On Printer processes raw binary PostScript print jobs from computers using the Macintosh operating system.
Off Printer filters PostScript print jobs using standard protocol.
Auto* Printer processes print jobs from computers using either Windows or Macintosh operating systems.
NPA Mode To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines data and determines the format and then processes it appropriately.

Menu Item Purpose Values
To configure the size of the parallel input buffer.
Disabled Disables job buffering. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the Parallel Buffer size (recommended setting).
3K to maximum size allowed
User specifies the Parallel Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Parallel Buffer size, disable or reduce the size of the serial, and USB buffers.
To control the pull-up resistors on the parallel port signals. This menu item is useful for personal computers that have open collector outputs on the parallel port signals.
On Disables the resistors.
Off* Enables the resistors.
To determine whether the parallel port data is sampled on the leading or trailing edge of strobe.
On* Samples parallel port data on the leading edge of strobe.
Off Samples parallel port data on the trailing edge of strobe.
To configure the printer so it automatically switches to PCL emulation when a print job requires it. This print job is received through the parallel port, regardless of the default printer language.
On* Printer examines data on the parallel interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.
To configure the printer so it automatically switches to PostScript emulation when a print job received through the parallel port requires it, regardless of the default printer language.
On* Printer examines data on the parallel interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.

Menu Item Purpose Values
Protocol To specify the parallel interface protocol.
Standard May resolve some parallel interface problems.
Fastbytes* Provides compatibility with most existing parallel interface implementations (recommended setting).
Use the PCL Emul Menu to change printer settings that only affect jobs using the PCL emulation printer language.
Menu Item Purpose Values
A4 Width To select the width of the logical page for A4 size paper.
198 mm* Makes the logical page compatible with the Hewlett-Packard LaserJet 5 Printer.
203 mm Makes the logical page wide enough to print eighty 10-pitch characters.
Auto CR after LF
To specify whether the printer automatically performs a carriage return after a line feed control command.
Off* Printer does not perform a carriage return after a line feed control command.
On Printer performs a carriage return after a line feed control command.
Auto LF after CR
To specify whether the printer automatically performs a line feed after a carriage return control command.
Off* Printer does not perform a line feed after a carriage return control command.
On Printer performs a line feed after a carriage return control command.
Font Name To choose a specific font from the specified font source.
R0 Courier 10* The font name and font ID for all fonts in the selected font source are displayed. The font source abbreviation is R for resident, F for flash, K for disk, and D for download.
PCL Emul Menu

Menu Item Purpose Values
Font Source To determine the set of fonts displayed in the Font Name menu item.
Resident* Displays all fonts resident in printer RAM when the printer ships from the factory.
Download Displays all fonts downloaded to printer RAM.
Flash Displays all fonts stored in flash memory.
Disk Displays all fonts stored on the printer hard disk.
All Displays all fonts available to the printer from all sources.
To determine the number of lines that print on each page.
1...255 The printer sets the amount of space between each line (vertical line spacing) based on the Lines per Page, Paper Size, and Orientation menu items. Select the correct Paper Size and Orientation before changing Lines per Page.
60* (country/ region- specific factory default values)
64* (country/ region- specific factory default values)
Orientation To determine how text and graphics are oriented on the page.
Portrait* Prints text and graphics parallel to the short edge of the paper.
Landscape Prints text and graphics parallel to the long edge of the paper.
Pitch To specify the font pitch for scalable monospaced fonts.
0.08...100 (in increments of 0.01 cpi)
Pitch refers to the number of fixed- space characters in a horizontal inch of type. You can select a pitch from 0.08 to 100 characters per inch (cpi) in increments of 0.01 cpi. For nonscalable monospaced fonts, the pitch is displayed, but cannot be changed.
Point Size To change the point size for scalable typographic fonts.
1...1008 in increments of 0.25 points)
Point size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch. You can select point sizes from 1 to 1008 in increments of 0.25 points.

Menu Item Purpose Values
Symbol Set To choose a symbol set for a specified font name.
10U PC-8* (country/ region- specific factory default values)
A symbol set is a set of alphabetic and numeric characters, punctuation, and special symbols used when printing with a selected font. Symbol sets support the different requirements for languages or specific programs, such as math symbols for scientific text. Only the symbol sets supported for the selected font name are displayed.
12U PC-850* (country/ region- specific factory default values)
To configure your printer to work with printer drivers or programs that use different source assignments for the paper trays.
1 Select a paper source. Assign Tray <x>
2 Select a value. Off* Printer uses factory default paper source assignments.
0...199 Select a numeric value to assign a custom value to a paper source.
None Paper source ignores the Select Paper Feed command.
Other Tray Renumber selections View Factory Def
Press Menu to display the factory default value assigned to each paper source.
Select Yes to return all tray assignments to factory default values.

Paper Menu
Use the Paper Menu to define the paper loaded in each paper tray and the default paper source and output bin.
Menu Item Purpose Values
To send print jobs to a specific output bin based on the requested paper type.
Custom <x> Bin (where represents 1 through 6)
To determine which output bin(s) the printer uses for a particular job.
Mailbox* Sends print jobs to the output bin designated for that user.
Link Links two or more bins together as though they were one large bin. When one linked bin is full, the printer starts filling the next linked bin, and continues with each additional linked bin.
Mail Overflow Sends print jobs to the output bin designated for that user until it is full, and then sends jobs to the designated overflow bin.
Link Optional Links all optional output bins as though they were one large bin, while leaving the standard bin individually addressable.
Sends each job to the output bin specified for that paper type.

Menu Item Purpose Values
To determine when the printer selects paper loaded in the multipurpose feeder.
Cassette* Printer treats the multipurpose feeder like any other paper tray. If a print job requests a paper size or type that is only loaded in the multipurpose feeder, the printer pulls paper from the multipurpose feeder for the job.
Manual Printer treats the multipurpose feeder like a manual feed tray, and displays Load Manual when you need to insert a single sheet of paper in the feeder.
First Printer pulls paper from the multipurpose feeder until it is empty, regardless of the paper source or paper size requested for the job.
Printer treats the multipurpose feeder like any other paper tray, except envelopes are not automatically supported.
To specify the kind of paper associated with each of the Custom Types available in the Paper Type menu item.
Values for Custom Type , where represents 1, 2, 3, 4, 6 (paper only), or 5 (transparencies only):
Paper* Note: If a user-defined name is available, it is displayed instead of Custom Type . The user- defined name is truncated to 14 characters. If two or more custom types share the same name, the name only appears once in the Custom Types value list.
Output Bin To specify the default bin for printed material.
available, it is displayed instead of Bin . The name is truncated to 14 characters. If two or more bins share the same name, the name only appears once in the Output Bin value list.

Menu Item Purpose Values
To properly handle preprinted paper loaded in a tray, whether the job is a duplexed job or a single-sided job.
1 Select a paper type.
2 Select a value. Duplex Notifies the printer that the specified paper type is loaded properly for duplex printing. If the printer receives a single-sided job using that paper type, the printer inserts blank pages as necessary to print the job properly on preprinted forms. This setting may slow single-sided printing.
Off* Printer assumes preprinted material is loaded for single-sided printing. Duplexed jobs may not print properly.

Menu Item Purpose Values
Paper Size To identify the default paper size for each paper source. For trays with automatic size sensing, only the value detected by the hardware is displayed.
1 Select a paper source. Tray <x> Size
2 Select a value.
(* Denotes country/region- specific factory default values)
A5
B5
DL Envelope* (non US)
Universal Select Universal when you load paper that does not match any of the other available sizes. The printer automatically formats the page for the maximum possible size. You can then set the actual page size from your program’s software.
Paper Source To identify the default paper
Tray <x> (Tray 1*)
If you loaded the same size and type of paper in two paper sources (and the Paper Size and Paper Type menu items are correctly set), the trays are automatically linked. When one paper source is empty, paper automatically feeds from the next linked source.
source.

Menu Item Purpose Values
Paper Type To identify the type of paper installed in each paper source.
Use this menu item to:
1 Select a paper source. Tray <x> Type
2 Select a value. Plain Paper
The Paper Type default for each envelope source is Envelope. The Paper Type default for each paper tray is as follows:
Tray 1–Plain Paper
Tray 2–Custom Type 2
Tray 3–Custom Type 3
Tray 4–Custom Type 4
Manual Pap Type–Custom Type 6

Menu Item Purpose Values
Paper Weight To identify the relative weight of the paper loaded in a specific source and ensure that the
toner adheres properly to the printed page.
1 Select a paper type.
2 Select a value. Light
To have the printer substitute the specified paper size if the requested size is not loaded.
Off Printer prompts the user to load the requested paper size.
Statement/A5 Prints A5 size jobs on statement size paper if only statement size paper is loaded, and prints statement size jobs on A5 paper if only A5 paper is loaded.
Letter/A4 Prints A4 size jobs on letter size paper if only letter size paper is loaded, and prints letter size jobs on A4 size paper if only A4 size paper is loaded.
All Listed* Substitutes Letter/A4 and Statement/A5.

Menu Item Purpose Values
To determine the default size when the Paper Size setting for a tray or feeder is Universal.
1 Select a unit of measure.
(* Denotes a country/region- specific factory default value)
2 Select the values. Portrait Width =76–360 mm (216 mm*)
=3.00–14.17 in. (8.5 in.*)
=76–360 mm (360 mm*)
=3.00–14.17 in. (14.17 in.*)

Fax Menu
Use the Fax Menu to change fax settings for your printer.
Menu Item Purpose Value
Fax Setup • Station Name
= (An alphanumeric value which is 20 characters.) The value is displayed using the encoding determined by the value of Display Language.
= (An alphanumeric value which is 20 characters.) The value is displayed using the encoding determined by the value of Display Language.

Menu Item Purpose Value
=JIS B5
=JIS B4
=A3

Menu Item Purpose Value

Menu Item Purpose Value
Fax Send • Automatic Redial
=0 ... 14 (5*)
=1 ... 200 (3*)

Menu Item Purpose Value
Fax Receive • Fax Storage
=JIS B5
=JIS B4
=A3

Menu Item Purpose Value
=1 ... 25 (1*)

PostScript Menu
Use the PostScript Menu to change printer settings that only affect jobs using the PostScript emulation printer language.
Menu Item Purpose Values
Font Priority To establish the font search order.
Resident* Printer searches printer memory for the requested font before searching flash memory or hard disk.
Flash/Disk Printer searches the hard disk and flash memory for the requested font before searching printer memory.
To enhance the contrast and sharpness of low resolution bitmapped images (such as images downloaded from the World Wide Web) and smooth their color transitions.
Off* Uses default resolution when printing all images.
On Enhances low resolution images, such as graphics with a resolution of 72 dpi.
To print a page defining the PostScript emulation error when an error occurs.
Off* Discards the print job without printing an error message.
On Prints an error message before it discards the job.
Image Smoothing · Print PS Error · PostScript Menu

Serial Menu
Use the Serial Menu to change printer settings affecting jobs sent to the printer through a serial port (either Standard Serial or Serial Opt ).
Menu Item Purpose Values
Baud To specify the rate at which data can be received through the serial port.
Data Bits To specify the number of data bits that are sent in each transmission frame.
Honor DSR To determine whether the printer uses the Data Set Ready (DSR) signal. DSR is one of the handshaking signals for most serial interface cables.
Off* All data received by the serial port is treated as valid data.
On Only data received while the DSR signal is high is treated as valid.
The serial interface uses DSR to distinguish data sent by the computer from data created by electrical noise in the serial cable. This electrical noise can cause stray characters to print. Select On to prevent stray characters from printing.
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.

Menu Item Purpose Values
NPA Mode To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
On Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
Off Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
Parity To select the parity for serial input and output data frames.
RS-232/RS- 422 Designates the serial communication configuration: RS232 or RS422.
=RS-422
This allows the user to specify the RS-422 polarity if RS-422 communications is active for the serial port.
To configure the printer so it automatically switches to PCL emulation when a print job received through the serial port requires it, regardless of the default printer language.
On* Printer examines data on the serial interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.

Menu Item Purpose Values
To configure the printer so it automatically switches to PostScript emulation when a print job received through the serial port requires it, regardless of the default printer language.
On* Printer examines data on the serial interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
Robust XON To determine whether the printer communicates availability to the computer.
Off* Printer waits to receive data from the computer.
On Printer sends a continuous stream of XONs to the host computer to indicate that the serial port is ready to receive more data.
This menu item only applies to the serial port if Serial Protocol is set to XON/XOFF.
Serial Buffer To configure the size of the serial input buffer.
Disabled Disables job buffering. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the Serial Buffer size (recommended setting).
3K to maximum size allowed
User specifies the Serial Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Serial Buffer size, disable or reduce the size of the parallel, and USB buffers.
To select the hardware and software handshaking values for the serial interface.
DTR* Hardware handshaking.
DTR/DSR Hardware handshaking.
XON/XOFF Software handshaking.
Combined hardware and software handshaking.
Combined hardware and software handshaking.
PS SmartSwitch · Serial Protocol · Serial Menu

Setup Menu
Use the Setup Menu to configure a variety of printer features.
Menu Item Purpose Values
To establish whether the printer sounds an alarm when the printer requires operator intervention.
Off Printer does not sound an alarm.
Single* Printer sounds three quick beeps.
Continuous Printer repeats three beeps every 10 seconds.
To define the amount of time (in seconds) the printer waits after displaying an operator intervention error message before it resumes printing.
Disabled* Printer does not resume printing until someone clears the error message.
5...255 Printer waits the specified amount of time, and then automatically resumes printing. This timeout value also applies if the menus are displayed (and the printer is offline) for the specified period of time.
To determine the language of the text on the operator panel display.

Menu Item Purpose Values
To specify the storage location for downloaded resources.
RAM* All downloaded resources are automatically stored in printer memory (RAM).
Storing downloaded resources in flash memory or on a hard disk is permanent storage rather than the temporary storage that RAM provides. The resources remain in the flash memory or on the hard disk even when the printer is turned off.
Flash All downloaded resources are automatically stored in flash memory.
Disk All downloaded resources are automatically stored on the hard disk.
To specify how the printer responds when the hole punch box becomes full.
Off* Hole Punch Waste Full is displayed until someone empties the hole punch box. If an Auto Continue value is selected from the Setup Menu, the printer resumes printing after the specified timeout value.
Single Printer stops printing, displays Hole Punch Waste Full, and sounds three quick beeps.
Continuous Printer stops printing, displays Hole Punch Waste Full, and repeats three beeps every 10 seconds until the hole punch box is emptied.
To establish whether the printer reprints jammed pages.
On Printer reprints jammed pages.
Off Printer does not reprint jammed pages.
Auto* Printer reprints a jammed page unless the memory required to hold the page is needed for other printer tasks.
To store statistical information about your most recent print jobs on the hard disk. The statistics include whether the job printed with or without errors, the print time, the job size (in bytes), the requested paper size and paper type, the total number of printed pages, and the number of copies requested.
Off* Printer does not store job statistics on disk.
On Printer stores job statistics for the most recent print jobs.

Menu Item Purpose Values
Page Protect To successfully print a page that may otherwise generate Complex Page errors.
Off* Prints a partial page of data if memory is insufficient to process the entire page.
If, after selecting On, you still cannot print the page, you may also have to reduce the size and number of fonts on the page, or increase the installed printer memory.
On Ensures that an entire page is processed before it prints.
For most print jobs, you do not need to select On. When On is selected, printing may be slower.
Power Saver To specify the amount of time (in minutes) the printer waits after a job is printed before it goes into a reduced power state.
Disabled This value does not appear unless Energy Conserve is set to Off.
1...240 Specifies the amount of time after a print job before the printer goes into Power Saver mode. (Your printer may not support the entire range of values.)
The factory default Power Saver setting depends on your printer model. Print the menu settings page to determine the current Power Saver setting. When the printer is in Power Saver mode, it is still ready to receive print jobs.
Select 1 to put the printer in Power Saver mode one minute after it finishes a print job. This uses much less energy, but requires more warm-up time for the printer. Select 1 if your printer shares an electrical circuit with room lighting and you notice lights flickering.
Select a high value if your printer is in constant use. Under most circumstances, this keeps the printer ready to print with minimum warm-up time. Select a value between 1 and 240 minutes if you want a balance between energy consumption and a shorter warm- up period.
Print Area To modify the logical and physical printable area.
Normal* Note: The Whole Page setting only affects pages printed using PCL 5 interpreter. This setting has no effect on pages printed using the PCL XL or PostScript interpreters. If you try to print any data in the non-printable area defined by Normal Print Area, the printer clips the image at the boundary defined by the Normal defined printable area.
Fit to Page · Whole Page · Setup Menu

Menu Item Purpose Values
To specify the amount of time (in seconds) the printer waits before printing the last page of a print job that does not end with a command to print the page. The print timeout counter does not start until Waiting is displayed.
Disabled The printer does not print the last page of a print job until one of the following occurs:
1...255 (90*) The printer prints the last page after the specified time. (Your printer may not support the entire range of values.)
To establish the default printer language used to communicate data from the computer to the printer.
PCL emulation, compatible with Hewlett-Packard printers.
PostScript emulation, compatible with Adobe PostScript language.
To determine the behavior of the image transfer unit during printing.
Max Speed The image transfer unit is engaged throughout the print job.
Max Yield* The image transfer unit position is engaged based on page content. This may extend the life of certain print supplies.
To determine what the printer does with downloaded resources, such as fonts and macros stored in RAM, if the printer receives a job that requires more memory than is available.
Off* Printer retains downloaded resources only until memory is needed. It then deletes those resources associated with the inactive printer language.
On Printer retains all downloaded resources for all printer languages during language changes and printer resets. If the printer runs out of memory, 38 Memory Full is displayed.

Menu Item Purpose Values
Staple Alarm To specify how the printer responds when it is out of staples.
Off Load Staples is displayed until someone loads staples. If an Auto Continue value is selected from the Setup Menu, the printer resumes printing after the specified timeout value.
Single* Printer stops printing, displays Load Staples, and sounds three quick beeps.
Continuous Printer stops printing, displays Load Staples, and repeats three beeps every 10 seconds until the staple cartridge is replaced.
Toner Alarm To specify how the printer responds when it is low on toner.
Off An error message is displayed until someone replaces the toner cartridge. If an Auto Continue value is selected from the Setup Menu, the printer resumes printing after the specified timeout value.
Single* Printer stops printing, displays an error message, and sounds three quick beeps.
Continuous Printer stops printing, displays an error message, and repeats three beeps every 10 seconds until the toner cartridge is replaced.
Wait Timeout To specify the amount of time (in
Disabled Disables Wait Timeout.
seconds) the printer waits to receive additional bytes of data from the computer. When this timeout expires, the print job is canceled.
15...65535 (40*)
Specifies the amount of time the printer waits for additional data before it cancels the job.
Wait Timeout is only available when you use PostScript emulation. This menu item has no effect on PCL emulation print jobs.
Start Page The purpose of this page is to clean oil from the fuser and improve OHP quality when printed after a POR. The default for the setting is Off.
=On · =Off* · Setup Menu

Supplies Menu
The Supplies Menu provides information about printer supplies that require attention. It is only available when a supply is low or needs replacement.
Menu Item Purpose Values
To view the status of the color print cartridges.
To view the status of the color photoconductor.
To view the status of the black photoconductor.
Fuser To view the status of the fuser. =Life Warning
Belt To view the status of the belt. =Life Warning

Menu Item Purpose Values
Supplies Life To view the status of all of the
printer supplies.
Selecting this takes the user through the appropriate screens to help replace these items.
The "Replaced" option tells the printer that the item was replaced and resets the engine counters for that item.

USB Menu
Use the USB Menu to change printer settings affecting a Universal Serial Bus (USB) port (USB Option ).
Menu Item Purpose Values
To temporarily store jobs on the printer hard disk before printing.
Off* Does not buffer print jobs to the hard disk.
On Buffers print jobs to the hard disk.
Auto Buffers print jobs only if the printer is busy processing data from another input port.
To configure the printer to process Macintosh binary PostScript print jobs.
Off Printer processes raw binary PostScript print jobs from computers using the Macintosh operating system.
On Printer filters PostScript print jobs using standard protocol.
Auto* Printer processes print jobs from computers using either Windows or Macintosh operating systems.
NPA Mode To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol.
Off Printer performs NPA processing. If data is not in NPA format, it is rejected as bad data.
On Printer does not perform NPA processing.
Auto* Printer examines the data to determine the format and then processes it appropriately.
To configure the printer so it automatically switches to PCL emulation when a print job received through the USB port requires it, regardless of the default printer language.
On* Printer examines the data on the USB interface and selects PCL emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off.

Menu Item Purpose Values
To configure the printer so it automatically switches to PostScript emulation when a print job received through the USB port requires it, regardless of the default printer language.
On* Printer examines data on the USB interface and selects PostScript emulation if the data indicates that is the required printer language.
Off Printer does not examine the incoming data. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off.
USB Buffer To configure the size of the USB input buffer.
Disabled Job buffering is disabled. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes.
Auto* Printer automatically calculates the USB Buffer size (recommended setting).
3K to maximum size allowed
User specifies the USB Buffer size. The maximum size depends on the amount of memory in your printer, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the USB Buffer size, disable or reduce the size of the parallel, serial, and network buffers.
Use the Utilities Menu to print a variety of listings relating to available printer resources, printer settings, and print jobs. Other menu items let you set up printer hardware and troubleshoot printer problems.
Menu Item Purpose Values
To retrieve storage area lost when resources are deleted from flash memory.
Yes Printer transfers all resources stored in flash memory to printer memory and then reformats the flash memory option. When the format operation is complete, the resources are loaded back into flash memory.
No Printer cancels the request to defragment the flash memory.
PS SmartSwitch · Defragment Flash · Utilities Menu

Menu Item Purpose Values
To return your printer settings to the factory default values.
Restore • All menu items are returned to the factory default values except: – Display Language. – All settings in the Parallel Menu,
Serial Menu, Network Menu, and USB Menu. • All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted. (Resources residing in flash memory or on the hard disk are unaffected.)
User-defined settings remain.
The Remove Held Jobs operation is used to remove Print and Hold jobs from the disk, because unwanted jobs may tend to pile up on the disk.
Format Disk To format the printer hard disk.
Yes Deletes any data stored on the hard disk and prepares the device to receive new resources.
No Cancels the request to format the hard disk and leaves current resources stored on the disk.
Format Flash To format the flash memory.
Yes Deletes any data stored in flash memory and prepares the flash memory to receive new resources.
No Cancels the request to format the flash memory and leaves current resources stored in flash memory.
Hex Trace To help isolate the source of a print job problem. With Hex Trace selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed.
To exit Hex Trace, turn the printer off or reset the printer from the Job Menu.
When this menu item is chosen, the user alignment pages print.

Menu Item Purpose Values
Job Acct Stat To print a listing of all job statistics
Print Prints all statistics available for the most recent print jobs.
stored on the hard disk, or to clear all statistics on the disk.
Clear Deletes all accumulated job statistics from the hard disk.
To print a list of all the resources stored in flash memory or on the hard disk.
Print Demo The Print Demo menu contains a list of the demo files available in the RIP code SIMM, the flash option, and the disk option.
Color sample pages are printed using the same paper selection method and Printer Settings as is used to print the resident demo page with the exception of Print Mode. These pages always print with Print Mode set to Color.
The multipage Color Sample can be used as an aid to select colors for applications. The RGB percent- ages will be printed on the chart for easy reference.
Print Fonts To print a sample of all the fonts available for the selected printer language.
PCL Fonts Prints a sample of all printer fonts available for PCL emulation.
PS Fonts Prints a sample of all printer fonts available for PostScript emulation.
Print Menus To print a listing of the current user default values, the installed options, the amount of installed printer memory, and the status of printer supplies.
Print Net <x> Setup
To print information relating to the internal print server and the network settings defined by the Network Setup menu item in the Network Menu.
Print Directory · Color Samples · Utilities Menu

The operator panel displays messages describing the current state of the printer and indicates possible printer problems you must resolve. This topic provides a list of all printer messages, explains what they mean, and tells you how to clear the messages For Finisher error messages, see the Finisher Manual.
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
Message What this message means What you can do
The printer is activating changes made to the printer settings.
Wait for the message to clear.
See also:
Disabling operator panel menus
Bin <x> Full The specified bin is full. Remove the stack of paper from the bin to clear the message. If you assigned the bin a name, the bin name is displayed instead of the bin number.
Busy The printer is busy receiving, processing, or printing data.
Canceling Fax The printer is processing a request to cancel a fax job.
Wait for the message to clear.
Canceling Job The printer is processing a request to cancel the current print job.
Wait for the message to clear.
See also:
Change <x> The printer is requesting that a different type of paper be loaded in one of the input sources.
Change the paper type in the specified source.
See also:
Loading a paper tray; Setup Guide
Canceling Job · Understanding printer messages

Message What this message means What you can do
The specified device is either not fully connected to the printer or is experiencing a hardware failure.
The printer is deleting all job statistics stored on the hard disk.
Wait for the message to clear.
Close Front Door The printer front door is open. Close the printer front door to clear the message.
Close Side Door The printer side door is open. Close the printer side door to clear the message.
Close Top Door The printer top door is open. Close the printer top door to clear the message.
The high capacity feeder door is open.
Close the top cover to clear the message.
Copying The printer is processing a copy job originating from the scanner.
Wait for the message to clear.
Defragmenting The printer is defragmenting the flash memory to reclaim storage space occupied by deleted resources.
Wait for the message to clear.
Delete All Jobs The printer is requesting confirmation to delete all held jobs.
Deleting Jobs The printer is deleting one or more held jobs.
Wait for the message to clear.
You have turned on the printer while the transfer belt is in the warning state and needs to be replaced.
Understanding printer messages

Message What this message means What you can do
You have turned on the printer while the fuser is in the warning state and needs to be replaced.
Disabling Menus The printer is responding to a request to disable the menus.
See also:
Disabling operator panel menus
The printer has attempted a disk recovery process and cannot repair the disk.
See also:
Disk Recovery x/5 yyy%
The printer is attempting to recover the hard disk. Disk recovery takes place in five phases; the second line on the operator panel display shows the percent complete of the current phase.
Wait for the message to clear.
Enabling Menus The printer is responding to a request to make the menus available to all users.
Wait for the message to clear, and then press Menu to view the menus from the operator panel.
Engine Warming The printer is warming the fuser assembly to prepare for printing.
Wait for the message to clear.
The printer is waiting for you to enter your four-digit personal identification number (PIN).
Use the operator panel buttons to enter the PIN you identified in the driver when you sent the confidential job to the printer.
See also:
Using the Print and Hold function
Fax <x> The printer is processing an incoming fax.
Wait for the message to clear.
Flushing Buffer The printer is flushing corrupted print data and discarding the current print job.
Wait for the message to clear.
Understanding printer messages

Message What this message means What you can do
The printer is formatting the hard disk. When formatting takes longer than usual, the second line of the display shows the percent complete.
Wait for the message to clear.
Formatting Flash The printer is formatting the flash memory.
Wait for the message to clear.
The counter that tracks wear on the fuser has reached its limit.
See also:
The printer memory is too full to continue processing print jobs.
data stored in printer memory. – Install more printer memory. – Note: The messages 37
Insufficient Memory and Held Jobs may be lost alternate on the display.
See also:
Using the Print and Hold function; 37 Insufficient Memory
The printer memory cannot restore Print and Hold jobs from the printer hard disk.
Press Go to clear the message. Some of the Print and Hold jobs stored on the disk will not be restored.
Infrared <x> An infrared interface is the active communication link.
Insert Tray <x> The specified tray is either missing or not fully inserted.
Insert the specified tray completely.
See also:
Loading a paper tray
Replacing the fuser · Understanding printer messages

Message What this message means What you can do
The printer is requesting that a specified device be installed so it can print a job.
Invalid Engine Code The printer engine code has not been programmed or is not valid.
Call for service.
See also:
The code in an internal print server is not valid. The printer cannot receive and process jobs until valid code is programmed into the internal print server.
Download valid code to the printer internal print server.
Load <x> The printer is trying to feed paper from a source it detects is empty.
See also:
Loading a paper tray
Load Manual A request for a manual feed job has been sent to the printer. The printer is ready for insertion of a single sheet into the manual feed slot.
See also:
Loading the multipurpose feeder
LocalTalk <x> A LocalTalk interface is the active communication link.
Calling for service · or · Understanding printer messages

Message What this message means What you can do
Menus Disabled The printer menus are disabled. You cannot change the printer settings from the operator panel.
You can still open the Job Menu to cancel a job that is printing or to select a confidential job or a held job that you want to print. If you need access to the printer menus, contact your network administrator.
See also:
Disabling operator panel menus
An internal print server (also called an internal network adapter or INA) is being reset.
Wait for the message to clear.
Network <x> A network interface is the active communication link.
Network <x>, <y> A network interface is the active communication link, where represents the active communication link and represents the channel.
No DRAM is installed. Turn the printer off, install DRAM, and turn the printer back on.
See also:
The four-digit personal identification number (PIN) you entered is not associated with any confidential print job.
See also:
Using the Print and Hold function
Not Ready The printer is not ready to receive or process data. Someone pressed Stop to take the printer offline.
Press Go to make the printer ready to receive jobs.
Parallel <x> A parallel interface is the active communication link.
The printer is running the series of start-up tests it performs after it is turned on.
Wait for the message to clear.
Power Saver The printer is ready to receive and process data. It is reducing its electricity consumption while idle. If the printer remains inactive for the period of time specified in the Power Saver menu item (20 minutes is the factory default), the Power Saver message replaces the Ready message.
Setup Guide · Understanding printer messages

Message What this message means What you can do
Printer Calibrating The printer is adjusting the color tables to correct variations caused by environmental conditions.
Wait for the message to clear.
Print Jobs on Disk Jobs that were spooled to the hard disk before the printer was last turned off have not yet printed.
Printing Alignment Page The printer is processing or printing a test page that shows alignment values.
Wait until the page has completed printing.
Printing Directory List The printer is processing or printing a directory of all files stored in flash memory or on a hard disk.
Wait for the message to clear.
Printing Font List The printer is processing or printing a list of all available fonts for the specified printer language.
Wait for the message to clear.
The printer is processing or printing all job accounting statistics stored on the hard disk.
Wait for the message to clear.
Printing Menu Settings The printer is processing or printing the menu settings page.
Wait for the message to clear.
Prog Engine Code The printer is programming new code into the flash memory.
Wait for the message to clear.
Prog System Code The printer is programming new system code.
Wait for the message to clear and the printer to reset.
Program Flash The printer is storing resources, such as fonts or macros, in flash memory.
Wait for the message to clear.
Programming Disk The printer is storing resources, such as fonts or macros, on the hard disk.
Wait for the message to clear.
Understanding printer messages

Message What this message means What you can do
Programming Error P<x> An error occurred while the
Correct the problem specified on the second line of the display:
printer was programming code into memory.
The printer is deleting one or more held jobs and sending one or more jobs to print.
Wait for the message to clear.
Queuing Jobs The printer is sending one or more held jobs to print.
Wait for the message to clear.
Ready The printer is ready to receive and process print jobs.
Send a job to print.
Ready Hex The printer is in Hex Trace mode and is ready to receive and process print jobs.
The specified output bin, or bins, is full.
Remove the stack of paper from the specified bin(s) to clear the message.
The printer is resetting the counter that tracks wear on the fuser.
Wait for the message to clear.
Resetting the Printer The printer is resetting to the current default settings. Any active print jobs are canceled.
Wait for the message to clear.
Understanding printer messages

Message What this message means What you can do
Someone reset the printer or turned it on, and the printer detects Print and Hold jobs stored on the hard disk.
The printer is restoring the factory default printer settings. When factory default settings are restored:
Wait for the message to clear.
in the Setup Menu. – All settings in the Parallel
Menu, Serial Menu, Network Menu, USB Menu, and Fax Menu.
The printer is restoring held jobs from the hard disk.
Restoring Held Jobs The printer is restoring held jobs from the hard disk.
Wait for the message to clear.
Serial <x> A serial interface is the active communication link.
Wait for the message to clear.
Std Bin Full The standard bin is full. Remove the stack of paper in the bin to clear the message.
Supplies At least one of the printer supplies requires attention. For example, you may have a toner cartridge that is low on toner.
Press Menu to open the Supplies Menu and identify which supply item needs replacing. Replace the appropriate printer supplies.
Tray <x> Empty The specified tray is out of paper. Load paper in the tray to clear the
message.
Tray <x> Low The specified tray is low on paper.
Add paper to the tray to clear the message.
Understanding printer messages

Message What this message means What you can do
Tray <x> Missing The specified tray is either missing or not fully inserted into the printer.
Insert the tray completely into the printer.
Unsupported Disk The printer detects an unsupported disk.
USB <x> The printer is processing data through the specified USB port.
Wait for the message to clear.
Waiting The printer has received a page of data to print but is waiting for an End of Job command, a Form Feed command, or additional data.
The download emulator version on the firmware card does not match the printer code version.
The printer automatically clears the message in 30 seconds, and then disables the download emulator on the firmware card.
This error can occur if you update printer firmware or move a firmware card from one printer to another.
Download the correct download emulator version from the Lexmark Web site.
2<xx> Paper Jam The printer detects a paper jam. Clear the paper path.
The oil coating roll is either missing or incorrectly installed.
Correctly install the oil coating roll to clear the message and continue printing.
One or more of the color print units is either missing or incorrectly installed.
Correctly install the color print units to clear the message and continue printing.
The printer detects an unsupported toner cartridge.
Replace the unsupported toner cartridge.
The optional Heavy Media Tray is inserted into any tray location except Tray 1.
Remove the Heavy Media Tray from the invalid location to clear the message.
34 Incorrect Media The printer detects the wrong type of media in the listed source.
Place the requested media in the listed source and press Go.
Understanding printer messages

Message What this message means What you can do
34 Short Paper The printer has determined that the length of the paper in the source specified on the second line of the display is too short to print the formatted data.
The printer lacks the memory needed to enable Resource Save. This message usually indicates too much memory is allocated for one or more of the printer link buffers.
Auto, and exit the menus to activate the link buffer changes. – When Ready is displayed, enable
Resource Save from the Setup Menu. • Install additional memory.
The printer memory (or hard disk, if installed) does not have the free space necessary to collate the print job.
The printer cannot defragment flash memory, because the printer memory used to store undeleted flash resources is full.
Understanding printer messages

Message What this message means What you can do
37 Insufficient Memory The printer memory is full and cannot continue processing current print jobs.
data in printer memory. – Install additional printer memory.
See also: Using the Print and Hold function; Held Jobs May Be Lost; Held Jobs May Not Be Restored
38 Memory Full The printer is processing data, but the memory used to store pages is full.
the amount of text or graphics on a page and deleting unnecessary downloaded fonts or macros. – Install additional printer memory.
39 Complex Page The page may not print correctly because the print information on the page is too complex.
by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. – Set Page Protect to On in the
Setup Menu. – Install additional printer memory.
Understanding printer messages

Message What this message means What you can do
The printer detects an unsupported version of firmware on the installed firmware card.
The high capacity feeder detects an error in the size sensing mechanism.
The printer wants to send paper to the Bin 1 output tray, but the tray is closed.
51 Defective Flash The printer detects defective flash memory.
Press Go to clear the message and continue printing. You must install different flash memory before you can download any resources to flash.
52 Flash Full There is not enough free space in the flash memory to store the data you are trying to download.
53 Unformatted Flash The printer detects unformatted flash memory.
The printer has detected a serial interface error on a serial port.
Understanding printer messages

Message What this message means What you can do
The printer cannot establish communications with an installed network port.
54 Std Par ENA Connection Lost
The printer has lost the connection to an external print server (also called an external network adapter or ENA).
56 Serial Port <x> Disabled
Data has been sent to the printer through a serial port, but the serial port is disabled.
56 Parallel Port <x> Disabled
Data has been sent to the printer through a parallel port, but the parallel port is disabled.
56 USB Port <x> Disabled Data has been sent to the printer through a USB port, but the USB port is disabled.
57 Configuration Change
The printer cannot restore jobs from the disk because the printer trays or drawers have been changed.
Press Go to clear the message. Some of the Print and Hold jobs stored on the disk will not be restored.
58 Input Config Error Too many drawers with matching trays are installed on the printer.
Turn off and unplug the printer. Remove the additional drawers or reconfigure the offending option. Plug in the printer and turn it on.
Understanding printer messages

Message What this message means What you can do
Turn off and unplug the printer. Remove the additional output option(s). Plug in the printer and turn it on.
Too many hard disks are installed on the printer. The printer only supports one hard disk at a time.
Turn off and unplug the printer. Remove the excess hard disks from the printer. Plug in the printer and turn it on.
Too many flash memory options are installed on the printer.
Turn off and unplug the printer. Remove the excess flash memory. Plug in the printer and turn it on.
Too many drawers with matching trays are installed.
Turn off and unplug the printer. Remove the additional drawers. Plug in the printer and turn it on.
61 Defective Disk The printer detects a defective hard disk.
62 Disk Full There is not enough memory on the hard disk to store the data sent to the printer.
Understanding printer messages

Message What this message means What you can do
63 Unformatted Disk The printer detects an unformatted hard disk.
The printer detects an unsupported disk format.
The transfer belt has reached its end of life.
Replace the transfer belt.
See also:
Replacing the transfer belt
The transfer belt is nearing its end of life. If you do not have a transfer belt on hand, order one now. You can print approximately 500 pages before the 80 Belt Exhausted message appears.
Press Go to clear the message and continue printing. The Supplies message is displayed until you replace the transfer belt.
See also:
Replacing the transfer belt
The transfer belt and fuser have reached their end of life.
Replace the transfer belt and fuser.
See also:
Replacing the transfer belt; Replacing the fuser
The transfer belt and fuser are nearing their end of life. If you do not have a replacement transfer belt and fuser, order them now. You can print approximately 500 pages before the 80 Belt/Fuser Exhausted message appears.
Press Go to clear the message and continue printing. The Supplies message is displayed until you replace the transfer belt and fuser.
See also:
Replacing the transfer belt; Replacing the fuser
The fuser has reached its end of life.
Replace the fuser.
See also:
Replacing the fuser · Understanding printer messages

Message What this message means What you can do
The fuser is nearing its end of life. If you do not have a replacement fuser, order one now. You can print approximately 500 pages before the 80 Fuser Exhausted message appears.
Press Go to clear the message and continue printing. The Supplies message is displayed until you replace the fuser.
See also:
Microcode in the engine flash code module has failed a system check.
Press Go to clear the message and discard the code. Retransmit the microcode data from the host computer.
84 All Photo Devs Exhausted
All of the photodevelopers have reached their end of life.
The black photodeveloper has reached its end of life.
The black photodeveloper is nearing its end of life. If you do not have a replacement black photodeveloper kit, order one now. You can print approximately 100 pages before the 84 Black Photo Dev Exhausted message appears.
Press Go to clear the message and continue printing. The Supplies message is displayed until you replace the photodeveloper.
The printer has detected an abnormal photodeveloper.
Install a new photodeveloper to clear the message and continue printing.
The color photodevelopers have reached the end of their lives.
Replacing the fuser · Understanding printer messages

Message What this message means What you can do
The color photodevelopers are nearing the end of their lives. If you do not have a new color photodeveloper kit, order one now. You can print approximately 100 pages before the 84 Color Photo Devs Exhausted message appears.
Press Go to clear the message and continue printing. The Supplies message is displayed until you replace the photodevelopers.
The oil coating roll has reached its end of life.
The oil coating roll is nearing its end of life. If you do not have a replacement oil coating roll, order one now. You can print approximately 500 pages before the 85 Coating Roll Exhausted message appears.
Press Go to clear the message and continue printing. The Supplies message is displayed until you replace the oil coating roll.
The printer has detected an abnormal coating roll.
Install a good coating roll to clear the message and continue printing.
The printer has ceased operating because the specified toner cartridge is empty. You cannot print until you replace the specified toner cartridge.
Install a new toner cartridge.
The printer has detected that the toner supply in the specified cartridge is low. If you do not have the specified toner cartridge, order one now. You can print approximately 250 more pages before the cartridge becomes empty.
Turn the printer off and check all cable connections. Turn the printer back on. If the service message recurs, call for service and report the message number and description of the problem.
See also:
Calling for service · Understanding printer messages


By carefully selecting print media and loading them properly, you should be able to avoid most paper jams. If jams do occur, follow the steps outlined in this section.
To resolve the paper jam messages, you must clear the jammed area and then press Go to clear the message and resume printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto; however, the Auto setting does not guarantee the page will print.
To clear paper jams in the Finisher, see the Finisher Manual to locate jam access areas.
See the diagram below for the path the paper travels through the printer and options, and areas where jams may occur. The path varies depending on the paper source and output bin.
Click a message below for more information.

200 Paper Jam Check Areas A,B
200 Paper Jam Check Area D
T 2
T 3
T 4
240 Paper Jam · Clearing paper jams

200 Paper Jam <x> Pages Jammed (Check Areas A-F, T15, MPF)
This message identifies the areas (A–F, MPF, or T1–T5) you need to check to remove the paper or to clear the message. The display alternates between 200 Paper Jam <x> Pages Jammed and Check Areas A-F., T1-5, MPF:
Jam message Jam message
Check Areas A,B Check Area F
Check Area C Check MPF
Check Area D Check T1–T4
Check Area E Check T5
Paper Jam message is blank. To resolve the message, you must clear all paper from the paper path.
This message indicates a paper jam in the transfer belt, fuser, or output roller area. To clear areas A– B:
1 Complete the steps to open the top cover.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 113
Photodeveloper

2 Remove any paper on the transfer belt.
If the paper source was the multipurpose feeder, check the area between the multipurpose feeder and the transfer belt.

damage to the transfer belt.
3 Check the fuser area and top cover for additional jams.
If there is no jam in the fuser area or top cover, close the top cover and front door, and then press Go. If a jam is present, continue with step 4.
4 Lift the fuser pressure release lever.

200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 114
Transfer belt

5 Slowly pull the paper out of the fuser toward the inside of the printer.
6 Rotate the fuser pressure release lever down.
7 Check the top cover for additional jams.
If there is no jam in the top cover, close the top cover and front door. If a jam is present, continue with step 8.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 115

8 Remove the jam from the top cover.

9 Close the top cover and the front door.
10 Open the jam access door on the left side of the printer.

11 Remove any paper inside the printer.

200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 116

12 Close the jam access door.
To prevent additional paper jams, make sure both sides of the door are closed.
13 Press Go.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 117

Check Area C
Jams that cause a Check Area C message require opening the duplex jam access door. If you are printing on small paper, the following steps may not clear the jam. See Removing small size paper from the duplex unit.
1 Open the duplex jam access door on the right side of the printer.
2 Remove the jam.
3 Press Go.
If the paper jam message continues, check and clear all paper from the paper path.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 118

Check Area D
This message indicates a paper jam in the duplex unit area. To clear area D:
1 Open the duplex jam access door on the right side of the printer.
2 Gently pull out the duplex unit.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 119

3 Turn the paper forwarding dial counterclockwise.
If the paper advances out of the duplex unit, remove the jam and go to step 7. If the paper does not advance, go to step 4.
4 Open the duplex unit covers.
5 Remove the jam.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 120

6 Close the duplex unit covers.
7 Push the duplex unit until it stops.
8 Close the access door.
9 Press Go.
If the paper jam message continues, check and clear all paper from the paper path.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 121

Removing small size paper from the duplex unit
When printing on both sides of A5 or other small size paper, you may need to partially remove the duplex unit to clear the jam.
1 Turn off the printer.
2 Open the duplex unit door.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 122

3 Loosen the two screws shown.
4 Pull out the duplex unit far enough to see the duplex unit inlet.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 123

5 Remove jam from the duplex unit inlet.
6 Slide the duplex unit in.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 124

7 Align the thumbscrews on the duplex unit with the holes in the printer.
8 Tighten the thumbscrews to secure the duplex unit.
9 Close the duplex unit door.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 125

Check Area E
This message indicates a jam in the top, middle, or bottom optional drawer paper path area.
1 Open the jam access door on the top optional drawer.

2 Remove the jam.

3 Close the jam access door.
4 Repeat these steps for jams in the middle and bottom drawers.
5 Press Go. If the paper jam message continues, check and clear all paper from the paper path.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 126

Check Area F
1 Pull the high capacity feeder away from the printer.
2 Open the jam access door on the top optional drawer.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 127

3 Remove any jams.
4 Close the jam access door.
5 Slide the high capacity feeder until the feeder locks to the docking frame.
When the feeder is in the correct position, you hear a click.
6 Press Go.
If the paper jam message continues, check and clear all paper from the paper path.
200 Paper Jam <x> Pages Jammed (Check Areas A-F, T1-5, MPF) 128

240 Paper Jam Check MP Feeder
1 Slowly pull the jam straight out of the multipurpose feeder, except when feeding banner paper (11.69 X 36 in.). Clear banner paper jams only in the paper feed direction.
If the paper will not come out, proceed with step 2.

2 Open the top cover.
3 Remove the paper on the transfer belt.
the transfer belt or placing items on it may cause damage.

4 Close the top cover.
5 Press Go.
240 Paper Jam Check MP Feeder 129
Transfer belt

24<x> Paper Jam Check Tray <x>
Jams in five areas result in a 24<x> Paper Jam message, where x represents the tray number where the jam has occurred. Paper jam messages 241–244 indicate a jam has occurred in one of the paper trays. A 249 Paper Jam Check Tray <x> message indicates a jam has occurred in the high capacity feeder. See Identifying paper jam areas for tray numbering.
1 Pull out the tray indicated on the display.
2 Remove any wrinkled or creased paper.
24<x> Paper Jam Check Tray <x> 130

3 Push down on the remaining paper in the tray until the bottom plate clicks into place.
4 Close the tray.
5 Press Go.
If the paper jam message continues, check and clear all paper from the paper path.
24<x> Paper Jam Check Tray <x> 131

249 Paper Jam Check Tray <x>
A 249 Paper Jam Check Tray <x> message indicates a jam has occurred in the high capacity feeder.
tray 3.
1 Open the top cover.
2 Remove the jam.
24<x> Paper Jam Check Tray <x> 132

3 Close the top cover.
4 Press Go.
24<x> Paper Jam Check Tray <x> 133

Determining supply status
Print the menu settings page to check the status of printer supply items. See Printing the menu settings page for detailed instructions.
One or two pages print depending on the number of menu settings you have. Look for “Supplies Menu” on the page; each item indicates the percentage of remaining life.
You can also check the status of printer supply items using the operator panel.
1 Press Menu until you see Supplies Menu.
2 Press Select.
3 Press Menu until you see Supplies Life.
4 Press Select.
5 Press Menu to scroll through the printer supply items.
Several settings in your program’s software or on the display let you conserve toner and paper:
For more information, see...
Supply Setting What the setting does
Toner Toner Darkness in the Color Menu
Lets you adjust the amount of toner released on a sheet of paper. The values range from 1 (lightest setting) to 5 (darkest setting).
Toner Darkness · Maintenance

For more information, see...
Supply Setting What the setting does
Paper and specialty media
Multipage Print in the Finishing Menu
Prints two or more page images on one side of a sheet.
Values for Multipage Print are 2 Up, 3 Up, 4 Up, 6 Up, 9 Up, 12 Up, and 16 Up.
Combined with the duplex setting, Multipage Print lets you print up to 32 pages on one sheet of paper (16 images on the front and 16 on the back).
Duplex in the Finishing Menu
Available when you attach an optional duplex unit.
Paper and specialty media
Use your software application or printer driver to send a Verify Print job.
Lets you examine the first copy of a multiple-copy job to be sure it is satisfactory before you print the other copies. If the job is unsatisfactory, you may cancel the job.
Canceling a print job
Using the Print and Hold function
Use Held Jobs in the Job Menu to access your Verify Print job.

Ordering supplies
In the U.S. or Canada, call 1-800-438-2468 for information about Lexmark Authorized Supplies Dealers in your area. In other countries/regions, contact the place where you bought your printer.
You can also visit the Lexmark online store at www.lexmark.com to order supplies.
Replacing maintenance items as needed helps you maintain top performance, optimize print quality, and avoid printing problems.
When the 80 Fuser Life Warning message appears on the display, you should order a new fuser.
Use P/N 56P9900 to order a fuser for a 120 V printer. Use P/N 56P9901 to order a fuser for a 230 V printer.
When the 85 Coating Roll Life Warning message appears on the display, you should order a new oil coating roll.
Use P/N 12N0774 to order an oil coating roll.
When the 80 Belt Life Warning message appears on the display, you should order a new transfer belt.
Use P/N 56P9903 to order a transfer belt.
When the 88 <color> Toner Low message appears on the display, you should order a new toner cartridge. You can continue to print after the 88 <color> Toner Low message appears for a few hundred pages until the print fades or no longer prints satisfactorily, or until the 88 <color> Toner Empty message appears, at which time you must replace the toner cartridge to continue printing.
Ordering supplies

Order the appropriate toner cartridge:
Part number Toner cartridge Approximate yield Approximate coverage
12N0771 Black toner cartridge 14,000 pages 5%
12N0770 Yellow toner cartridge
12N0768 Cyan toner cartridge
12N0769 Magenta toner cartridge
The printer calculates and stores information on the number of images that have been printed. When a count for a supply nears the end of the supplies life, the SUPPLIES status message appears on the second line of the display to remind you there are supplies that need attention.
Open the SUPPLIES Menu to view the supplies that need to be replaced. Replacement of these parts ensures peak printer performance and prevents print quality and paper feed problems resulting from worn parts.
SUPPLIES
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
The printer counter keeps track of your toner cartridges, photodevelopers, fuser cleaner, fuser, and transfer belt. It posts a Low, Empty, Life Warning, or an Exhausted message on the display when one of these supplies nears or reaches an end of life condition. If you do not have the appropriate supply item, order one when the Low, Empty, or Life Warning message appears.
Press Go to clear the message. The SUPPLIES status message appears on the second line of the display to remind you there are supplies that need attention. Press Menu to open the Supplies Menu and quickly determine the supply items that need to be replaced.
The printer continues to display the SUPPLIES status message until you replace the required supply items.
After the SUPPLIES status message appears, the printer continues to monitor the required supply items until the supply is exhausted. The printer displays Low, Empty, Life Warning, or Exhausted.
Replacing supplies

To prevent damage to your printer or its components, some supply items do not allow the printer to operate when the item is exhausted. When this occurs, you must install the appropriate new supplies before you can continue printing.
To order finisher supplies (staples), see the Finisher Manual.
Store supplies in their original packaging until you are ready to install them.
Do not store supplies in:
Lexmark’s Operation ReSourceSM program lets you participate in a worldwide recycling effort at no cost to you.
Pack your old toner cartridge in the new toner cartridge shipping box. Follow the instructions in the box to send the old cartridge back to Lexmark.
You can also recycle some replacement hardware parts, such as the transfer belt and the fuser.
If a prepaid shipping label is not available for your country/region, contact the place where you bought your printer for additional recycling information.
cartridges from a third party. Print quality and printer reliability cannot be guaranteed if you do. The printer warranty does not cover damage caused by using refilled cartridges.
Storing supplies

Replacing a photodeveloper
Your printer monitors the life of your photodevelopers. When a photodeveloper reaches the end of its life, the printer displays 84 Black Photo Dev Exhausted or 84 Color Photo Devs Exhausted. This message indicates it is time to replace one or more specified photodevelopers. For best print quality, make sure you replace the fuser when the printer displays 84 Black Photo Dev Life Warning or 84 Color Photo Dev Life Warning.
Press Go to clear the message. The Supplies message appears on the second line of the display to remind you that supplies need attention. You can open the Supplies Menu to see which photodeveloper is nearly exhausted.
The printer continues to display the Supplies message until you replace the photodeveloper or until it is exhausted.
To replace a photodeveloper, use the following steps or the instruction sheet supplied with the photodeveloper.
1 Complete the steps to open the top cover.
soiled with toner in hot water; this permanently adheres the toner to the clothing. Use cold water to remove toner.
Replacing a photodeveloper

2 Pull the waste toner arm away from the photodeveloper.

3 Use the tab to pull the photodeveloper approximately halfway out of the printer.
Some force is initially required to pull the photodeveloper past the locking spring.

4 Grasp the photodeveloper handle and continue to pull the photodeveloper out.
Replacing a photodeveloper

Installing a photodeveloper
own color-coded position.
1 Remove the replacement photodeveloper from the packing material.
cover until you begin installing the photodeveloper in step 4.
2 Remove the tape from the photodeveloper and photodeveloper cover.
placed in a specific location in the printer.
Replacing a photodeveloper

3 Align the photodeveloper with the slot under the matching color label.

4 While holding the photodeveloper with your left hand and the photodeveloper cover with your right hand, slide the photodeveloper into the slot until it is fully seated.
As the photodeveloper slides in, slide off the photodeveloper cover.

Photodeveloper cover · Replacing a photodeveloper

5 Push the waste toner arm until it connects with the photodeveloper and snaps into place.
6 Repeat steps 2 through 5 to install additional photodevelopers.
area under the cover is free of hands, clothing, and other items.
7 Close the top cover and the front door.
For instructions about replacing other supply items, click one of the following headings:
Removing the duplex unit
Replacing the transfer belt
Your printer monitors the life of your fuser. When the fuser reaches the end of its life, the printer displays 80 Fuser Exhausted. This message indicates it is time for you to replace the fuser. For best print quality, make sure you replace the fuser when the printer displays 80 Fuser Life Warning.
Press Go to clear the message. The Supplies message appears on the second line of the display to remind you that supplies need attention. You can open the Supplies Menu to see the 80 Fuser Exhausted and 80 Fuser Life Warning messages.
Replacing the fuser

The printer continues to display the Supplies message until you replace the fuser. To replace the fuser, use the following steps or the instruction sheet supplied with the fuser.
1 Turn the printer on.
2 Follow the instructions in the table for the message your printer is displaying.
Primary message Secondary message What you should do
80 Fuser Life Warning Select = Replace
Press Select if you want to replace the fuser now.
Press Go if you want to wait to replace the fuser.
80 Fuser Exhausted Select = Replace Press Select to replace the fuser.
80 Fuser/Belt Life Warning
Press Select if you want to replace the fuser now.
Press Go if you want to wait to replace the fuser.
80 Fuser/Belt Exhausted Select = Replace Press Select to replace the fuser.
The Preparing for Maintenance message appears while the printer moves parts into position. After the parts are in position, the message Printer Ready for Maintenance appears, followed by Power Off to Replace Items.
3 Turn the printer off.
1 Complete the steps in Preparing for maintenance.
2 Make sure the printer is turned off.

3 Turn off or unplug any optional devices connected to the printer.
the transfer belt or placing items on it may cause damage.
4 Complete the steps to open the top cover.
Transfer belt · Replacing the fuser

5 Lift the fuser pressure release lever up.
down position will damage the lever.
6 Grasp the fuser handles and press both fuser release buttons.
Replacing the fuser

7 Lift the fuser up and out.
new fuser.
Replacing the fuser

Installing the fuser
1 Remove the replacement fuser from the packing material, and remove any packing material from the fuser.

2 Align the new fuser with the opening in the printer.

Replacing the fuser

3 Lower the fuser until it snaps into place.
Replacing the fuser

4 Remove the oil coating roll from the old fuser.
a Pull up on the locking tab to unlock the oil coating roll.

b Slide out the oil coating roll.

Hold the oil coating roll by the top, as indicated by the dark areas in the illustration.
slide the coating roll into the fuser immediately, place the coating roll on a sheet of plastic or other protective material to prevent stains.

5 Install the oil coating roll.
Make sure the oil coating roll drops down into position. It should click into place with no gap between it and the fuser.

area under the cover is free of hands, clothing, and other items.
6 Close the top cover and the front door.
7 Reconnect any optional devices to the printer.
8 Turn the optional devices on.
Replacing the fuser

9 Turn the printer on.
The message Did you replace Fuser? appears.
10 Press Go to reset the fuser counter.
message or the 80 Fuser/Belt Exhausted message, see Replacing the transfer belt for instructions on replacing the transfer belt.
For instructions about replacing the transfer belt, click the following heading:
Replacing the transfer belt
Your printer monitors the life of your oil coating roll. When the oil coating roll reaches the end of its life, the printer displays 85 Coating Roll Exhausted. This message indicates that you must replace the oil coating roll to continue printing.
For best print quality, make sure you replace the oil coating roll when the printer displays 85 Coating Roll Life Warning. Press Go to clear the message. The printer continues to display the Supplies message until you replace the oil coating roll.
To replace the oil coating roll, use the following steps or the instruction sheet supplied with the oil coating roll.
Replacing the oil coating roll

Removing the oil coating roll
1 Turn the printer off.
2 Turn off or unplug any optional devices connected to the printer.
the transfer belt or placing items on it may cause damage.
3 Complete the steps to open the top cover.
Replacing the oil coating roll
Transfer belt


4 Pull up on the locking tab to unlock the oil coating roll.
5 Slide the oil coating roll out of the fuser.

Hold the oil coating roll by the top, as indicated by the dark areas in the illustration.
6 Remove packing material from the new oil coating roll.
Replacing the oil coating roll
Hold here

7 Slide the oil coating roll into the fuser.

Make sure the oil coating roll drops down into position. It should click into place with no gap between it and the fuser.

area under the cover is free of hands, clothing, and other items.
8 Close the top cover and the front door.
9 Reconnect any optional devices to the printer.
10 Turn the optional devices on.
Replacing the oil coating roll

11 Turn the printer on.
For instructions about replacing other supply items, click one of the following headings:
Replacing the transfer belt
Your printer monitors the life of your transfer belt. When the transfer belt reaches the end of its life, the printer displays 80 Belt Exhausted. This message indicates it is time for you to replace the transfer belt. For best print quality, make sure you replace the transfer belt when the printer displays 80 Belt Life Warning.
Press Go to clear the message. The Supplies message appears on the second line of the display to remind you that supplies need attention. You can open the Supplies Menu to see 80 Belt Exhausted or 80 Belt Life Warning messages.
The printer continues to display the Supplies message until you replace the transfer belt. To replace the transfer belt, use the following steps or the instruction sheet supplied with the transfer belt.
Replacing the transfer belt
Replacing the fuser

Preparing for maintenance
1 Turn the printer on.
2 Follow the instructions in the table for the message your printer is displaying.
Primary message Secondary message What you should do
80 Belt Life Warning Select = Replace
Press Select if you want to replace the transfer belt now.
Press Go if you want to wait to replace the transfer belt.
80 Belt Exhausted Select = Replace Press Select to replace the transfer belt.
80 Fuser/Belt Life Warning
Press Select if you want to replace the transfer belt now.
Press Go if you want to wait to replace the transfer belt.
80 Fuser/Belt Exhausted Select = Replace Press Select to replace the transfer belt.
The Preparing for Maintenance message appears while the printer moves parts into position. After the parts are in position, the message Printer Ready for Maintenance appears, followed by Power Off to Replace Items.
3 Turn the printer off.
1 Complete the steps in Preparing for maintenance.
2 Make sure the printer is turned off.
Replacing the transfer belt
Go = Continue · Select = Replace · Go = Continue

3 Turn off or unplug any optional devices connected to the printer.
the transfer belt or placing items on it may cause damage.
4 Complete the steps to open the top cover.
Replacing the transfer belt
Transfer belt

5 Loosen the thumbscrews on each side of the transfer belt cover.

Replacing the transfer belt

7 Loosen the thumbscrews on each side of the transfer belt.

8 Pull the transfer belt out.

Replacing the transfer belt

Installing the transfer belt
1 Remove the replacement transfer belt from the packing material.

2 Align the transfer belt with the opening in the printer.

Replacing the transfer belt

3 Slide the transfer belt in until it is fully seated.

4 Tighten the transfer belt thumbscrews.

Replacing the transfer belt

5 Align and place the transfer belt cover as shown.

6 Tighten the transfer belt cover thumbscrews.

the transfer belt or placing items on it may cause damage.
Replacing the transfer belt

7 Lift and remove the four shipping spacers from the transfer belt.
be able to close the top cover.
area under the cover is free of hands, clothing, and other items.
8 Close the top cover and the front door.
9 Reconnect any optional devices to the printer.
10 Turn the optional devices on.
11 Turn the printer on.
The message Did you replace Belt? appears.
Replacing the transfer belt
Transfer belt

12 Press Go to reset the transfer belt counter.
Once the counter is reset, the Printing Alignment Page message appears and a test page prints. After the test page has printed, you are prompted to enter alignment values for each setting.
13 Press Menu to choose the alignment value.
14 Press Select to enter the value and continue to the next value.
After you have entered values for each alignment setting, the transfer belt should be aligned and the printer ready to print.
message or the 80 Fuser/Belt Exhausted message, see Removing the duplex unit for instructions on replacing the fuser.
For instructions about replacing other supply items, click one of the following headings:
Removing the duplex unit
Replacing a toner cartridge
Your printer monitors the toner level of your toner cartridges. When the toner is getting low, the printer displays 88 <color> Toner Low. This message indicates it is time for you to replace one or more specified toner cartridges. Press Go to clear the attendance message.
The Supplies status message appears on the second line of the display to remind you there are supplies that need attention. You can open the Supplies Menu to see which toner cartridge is low.
The printer continues to display the Supplies message until you replace the toner cartridge or until it is empty.
When the life of the toner cartridge has expired, the printer displays 88 <color> Toner Empty. You must replace the toner cartridge to continue printing.
Use the following steps or the instruction sheet supplied with the toner cartridge to replace it.
Replacing a toner cartridge

Removing a toner cartridge
the transfer belt or placing items on it may cause damage.
1 Complete the steps to open the top cover.
permanently adheres the toner to the clothing. Use cold water to remove toner.
Replacing a toner cartridge
Transfer belt

2 Pull the waste toner arm away from the photodeveloper.

3 Pull the toner cartridge approximately halfway out of the printer.
4 Grasp the toner cartridge handle and continue to pull the toner cartridge out.

Replacing a toner cartridge

Installing a toner cartridge
1 Remove the replacement toner cartridge from the packing material.
2 Gently shake the toner cartridge to distribute the toner evenly.
3 Remove the shipping tape and any additional packing material.
Replacing a toner cartridge

4 Align the toner cartridge with its slot in the printer. The toner cartridge is placed to the right of the corresponding colored label.

5 Slide the toner cartridge in until the cartridge is fully seated.

Replacing a toner cartridge
Colored label

6 Push the waste toner arm until it snaps into place over the photodeveloper.
7 Repeat steps 2 through 5 to install additional toner cartridges.
area under the cover is free of hands, clothing, and other items.
8 Close the top cover and the front door.
For instructions about replacing other supply items, click one of the following headings:
Replacing the transfer belt
After replacing the fuser or transfer belt, you must reset the maintenance counter.
Resetting the maintenance counter
Replacing the fuser

If the message Did you replace Fuser? or Did you replace Belt? appears, press Go. Otherwise, use the following steps to reset the fuser or transfer belt counter.
1 Press Menu until SUPPLIES MENU appears on the second line of the display.
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
2 Press Select to open the SUPPLIES MENU.
3 Press Menu until REPLACE SUPPLIES appears on the second line of the display.
REPLACE SUPPLIES
1 Menu 2 Select 3 Return 4
4 Press Select to open Replace Supplies.
Resetting the maintenance counter
Go 5 · Stop 6

5 Press Menu until Fuser appears on the second line of the display.
Fuser
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
6 Press Select to open the Fuser menu item.
7 Press Menu until =Replaced appears on the second line of the display.
=Replaced
1 Menu 2 Select 3 Return 4
Go 5 Stop 6
8 Press Select to reset the fuser counter to zero.
9 Press Go.
Resetting the maintenance counter

Cleaning the LEDs
If you are experiencing print quality problems such as voids, light streaks, or light print, you may need to clean the LEDs inside the top cover.
1 Complete the steps to open the top cover.

2 Remove all toner cartridges. See Removing a toner cartridge for more information.


Do not expose the photodeveloper to light for more than ten minutes. Fingerprints
Cleaning the LEDs

can affect the performance of the photodeveloper. Avoid touching the photodeveloper anywhere except the handles.
with toner in hot water; this permanently adheres the toner to the clothing. Use cold water to remove toner that has soiled clothing.
3 Wipe the glass lenses of all four LED heads with a clean, dry cloth or tissue paper.
4 Reinstall all toner cartridges. See Installing a toner cartridge for more information.
area under the cover is free of hands, clothing, and other items.
5 Close the top cover and the front door.
Cleaning the LEDs

Closing the top cover
area under the cover is free of hands, clothing, and other items.
1 Place both hands on the top cover as shown.
2 Press down firmly until the top cover clicks into place.

3 Rotate the top cover locking lever to the right.
cover and press down firmly until the top cover clicks into place.

Closing the top cover

4 Close the front door.
Closing the top cover

Opening the top cover
To access the printer supplies and some of the paper jam areas:
1 Open the front door.
2 Rotate the top cover locking lever to the left.
Opening the top cover

3 Push up on the right top cover locking button and lift at the points shown below.

4 Lift the top cover until it stops.

For information about replacing an individual supply item or clearing paper jams, click one of the following headings:
Opening the top cover
Replacing the fuser · Clearing paper jams

Removing the duplex unit
1 Turn the printer off.
2 Open the duplex unit door.
3 Loosen the thumbscrews securing the duplex unit.
Removing the duplex unit

4 Slide the duplex unit out.
5 Close the duplex unit door.
Removing the duplex unit

Removing the high capacity feeder
1 Turn the printer off.
2 Unplug the high capacity feeder power cord from the electrical outlet.
3 Disconnect the interface cable from the side of the high capacity feeder.
4 Roll the high capacity feeder away from the printer.
5 Remove the high capacity feeder from the guide rail.
Removing the high capacity feeder

6 Raise the guide rail and pull it away from the docking frame.
7 Remove the wrench from the holder in the high capacity feeder.
Removing the high capacity feeder

8 Remove the four screws securing the docking frame.
9 Insert the two side covers into the screw holes on the optional drawer until they snap into place.
Removing the high capacity feeder

Removing the system board access cover
You must remove the system board access cover to install memory cards, a firmware card, a hard disk, or an option card.
move or lift the printer make sure you have enough people to help. Use the handholds located on the sides to lift the printer.
1 Move the printer or place it in an area that will be convenient for removing the cover and components.
You need a number 2 Phillips screwdriver to remove the cover and system board.
2 Loosen the eight screws on the cover. Do not remove the screws completely.
3 Slide the cover up and away from the printer.


Removing the system board access cover
Screws · Screws

Locating memory and network options
Use the following illustration to locate the connector for the card you want to remove.

After you have removed the options, complete the following steps to install the cover and system board.
Locating memory and network options
Option card connector · Parallel connector · USB connector

You need a number 2 Phillips screwdriver to install the cover.
1 Make sure the printer is off and unplugged.
2 Align the holes on the access cover with the screws.

3 Place the cover against the printer and slide it down.

Installing the system board access cover

4 Tighten the eight screws.
5 Connect the printer cables and power cord, and turn the printer on.
non-ground fault interrupter (GFI) circuit.
1 Turn the printer off.
2 Unplug the power cord.
non-ground fault interrupter (GFI) circuit.
3 Disconnect the parallel or Ethernet cable from the printer.
If you have any other devices connected to the printer, turn them off and unplug any cables going to the printer.
move or lift the printer make sure you have enough people to help. Use the handholds located on the sides to lift.
4 Lift the printer and move it away from the optional drawer.

Removing an optional drawer

5 Lift the optional drawer.
Removing an optional drawer

Calling for service
When you call for printer service, describe the problem you are experiencing, the message on the display, and the troubleshooting steps you have already taken to find a solution. Also, if possible, print out a print menu, this will greatly speed up the troubleshooting process.
You need to know your printer model type and serial number. Refer to the label on the back of the printer near the power cord for this information.
The serial number is also listed on the menu settings page you can print from the Utilities menu.
For service in the U.S. or Canada, click Contact Lexmark from the drivers CD, and then click Customer Support. This link takes you to Lexmark’s technical service and support if you have internet access.
If the suggested corrective action does not fix the problem, call your service representative.
Job did not print or incorrect characters printed.
Make sure Ready appears on the operator panel before you send a job to print. Press Go to return to Ready.
Make sure print media is loaded. Press Go to return to Ready.
Verify the printer is using the correct printer language.
Verify you are using the correct printer driver.
Make sure the parallel, serial, ethernet, or USB cable is firmly plugged in at the back of the printer. Make sure you are using the correct cable. Use IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use RS-232 Serial, verify that a null modem cable is used.
If the printer is connected through a switch box, try a direct connection.
Verify the correct paper size is selected through the operator panel, in the printer driver, or in the software program.
Make sure PCL SmartSwitch and PS SmartSwitch are set to On.
Problem Action · Troubleshooting

Job did not print or incorrect characters printed (continued).
If you are using a print spooler, verify the spooler is not stalled.
Check the printer interface from the Setup Menu.
Determine which host interface you are using. Print a menu settings page to verify the current interface settings are correct. See Printing the menu settings page.
If you are using a serial interface:
Printer seems to print slowly. Make sure you select the appropriate Paper Type setting before sending a job to print.
If the Paper Type is set to Transparency, the printer adjusts the fuser temperature and slows printing to improve the print quality. After printing on this media, the printer requires additional time to warm the fuser after you select another Paper Type setting (such as Plain Paper or Letterhead).
Reduce the complexity of your print job. Eliminating the number and size of fonts, the number and complexity of images, and the number of pages in a job may increase print speed.
Set Page Protect Off from the Setup Menu.
Unexpected page breaks appear.
Increase the Print Timeout value in the Setup Menu.
Transparencies jam. If you just turned the printer on or the printer has been idle for a period of time, print on paper before trying to print on transparencies.
Disabling Power Saver may also prevent transparencies from jamming after the printer has been idle.
Paper is jammed in the fuser. Rotate the fuser pressure release lever down and remove the jammed paper. See Clearing paper jams for more information.
Part of the printed page was clipped or is cut off.
Make sure you have the correct size paper in the paper tray and the paper size is set correctly for the paper in the tray.
Printer is connected to the USB port, but will not print.
Make sure you are using Windows 98, Windows 2000, Windows Me, or another USB-capable operating system supported by your manufacturer.
Paper does not feed properly. Make sure you are using recommended media. Do not use 16 lb paper or paper greater than 32 lb with the duplex unit.
Make sure the adjustable guides in the paper tray are adjusted properly for the media you loaded.
Make sure the stack of media does not exceed the maximum stack height indicated on the tray.
Problem Action · Calling for service

Print media misfeeds or multiple feeds occur.
Make sure the print media you are using meets the specifications for your printer. Refer to the Card Stock & Label Guide for more information.
Flex print media before loading it in any of the paper sources.
Make sure the print media is loaded correctly.
Make sure the paper width and length guides on the paper sources are adjusted correctly.
Do not overfill the paper sources.
Do not force print media into the multipurpose feeder when you load it; otherwise, it may skew or buckle.
Remove any curled print media from paper sources.
Load the recommended print side correctly for the type of print media you are using. See Loading a paper tray for more information.
Load less print media in the paper sources.
Turn the print media over or around and try printing again to see if feeding improves.
Do not mix print media types.
Do not mix reams of print media.
Remove the top and bottom sheets of a ream before loading the print media.
Load a paper source only when it is empty.
Envelope misfeeds or multiple feeds occur.
Remove the stack of envelopes from the multipurpose feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the multipurpose feeder.
Push down the bottom plate until it locks into place. See Loading the multipurpose feeder for an illustration.
Job prints from the wrong paper source or on the wrong print media.
Check the Paper Type setting in the Paper Menu from the printer operator panel and in the printer driver.
Printer does not duplex pages. • Make sure Duplex is selected in either the Finishing Menu or the
program you are printing from. • Make sure you have enough printer memory installed.
Problem Action · Calling for service










Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2003 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550
Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Job did not print or incorrect characters printed. | Make sure Ready appears on the operator panel before you send a job to print. Press Go to return to Ready. | p.194 | |
| Job did not print or incorrect characters printed. | Make sure print media is loaded. Press Go to return to Ready. | p.194 | |
| Job did not print or incorrect characters printed. | Verify the printer is using the correct printer language. | p.194 | |
| Job did not print or incorrect characters printed. | Verify you are using the correct printer driver. | p.194 | |
| Job did not print or incorrect characters printed. | Make sure the parallel, serial, ethernet, or USB cable is firmly plugged in at the back of the printer. Make sure you are using the correct cable. Use IEEE 1284-compliant parallel cable. We recommend Lexmark part number 1329605 (10 ft) or 1427498 (20 ft). If you use RS-232 Serial, verify that a null modem cable is used. | p.194 | |
| Job did not print or incorrect characters printed. | If the printer is connected through a switch box, try a direct connection. | p.194 | |
| Job did not print or incorrect characters printed. | Verify the correct paper size is selected through the operator panel, in the printer driver, or in the software program. | p.194 | |
| Job did not print or incorrect characters printed. | Make sure PCL SmartSwitch and PS SmartSwitch are set to On. | p.194 | |
| Job did not print or incorrect characters printed (continued). | If you are using a print spooler, verify the spooler is not stalled. Check the printer interface from the Setup Menu. Determine which host interface you are using. Print a menu settings page to verify the current interface settings are correct. See Printing the menu settings page. If you are using a serial interface: • Make sure Honor DSR is set to Off. • Check the protocol, baud, parity, and data bit settings. The settings on the printer and on the host computer should match. | p.195 | |
| Printer seems to print slowly. | Make sure you select the appropriate Paper Type setting before sending a job to print. | p.195 | |
| Printer seems to print slowly. | If the Paper Type is set to Transparency, the printer adjusts the fuser temperature and slows printing to improve the print quality. After printing on this media, the printer requires additional time to warm the fuser after you select another Paper Type setting (such as Plain Paper or Letterhead). | p.195 | |
| Printer seems to print slowly. | Reduce the complexity of your print job. Eliminating the number and size of fonts, the number and complexity of images, and the number of pages in a job may increase print speed. | p.195 | |
| Printer seems to print slowly. | Set Page Protect Off from the Setup Menu. | p.195 | |
| Unexpected page breaks appear. | Increase the Print Timeout value in the Setup Menu. | p.195 | |
| Transparencies jam. | If you just turned the printer on or the printer has been idle for a period of time, print on paper before trying to print on transparencies. Disabling Power Saver may also prevent transparencies from jamming after the printer has been idle. | p.195 | |
| Paper is jammed in the fuser. | Rotate the fuser pressure release lever down and remove the jammed paper. See Clearing paper jams for more information. | p.195 | |
| Part of the printed page was clipped or is cut off. | Make sure you have the correct size paper in the paper tray and the paper size is set correctly for the paper in the tray. | p.195 | |
| Printer is connected to the USB port, but will not print. | Make sure you are using Windows 98, Windows 2000, Windows Me, or another USB-capable operating system supported by your manufacturer. | p.195 | |
| Paper does not feed properly. | Make sure you are using recommended media. Do not use 16 lb paper or paper greater than 32 lb with the duplex unit. | p.195 | |
| Paper does not feed properly. | Make sure the adjustable guides in the paper tray are adjusted properly for the media you loaded. | p.195 | |
| Paper does not feed properly. | Make sure the stack of media does not exceed the maximum stack height indicated on the tray. | p.195 | |
| Print media misfeeds or multiple feeds occur. | Make sure the print media you are using meets the specifications for your printer. Refer to the Card Stock & Label Guide for more information. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Flex print media before loading it in any of the paper sources. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Make sure the print media is loaded correctly. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Make sure the paper width and length guides on the paper sources are adjusted correctly. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Do not overfill the paper sources. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Do not force print media into the multipurpose feeder when you load it; otherwise, it may skew or buckle. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Remove any curled print media from paper sources. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Load the recommended print side correctly for the type of print media you are using. See Loading a paper tray for more information. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Load less print media in the paper sources. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Turn the print media over or around and try printing again to see if feeding improves. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Do not mix print media types. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Do not mix reams of print media. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Remove the top and bottom sheets of a ream before loading the print media. | p.196 | |
| Print media misfeeds or multiple feeds occur. | Load a paper source only when it is empty. | p.196 | |
| Envelope misfeeds or multiple feeds occur. | Remove the stack of envelopes from the multipurpose feeder. Load one envelope, feed it through the printer, and then reload the stack of envelopes in the multipurpose feeder. | p.196 | |
| Envelope misfeeds or multiple feeds occur. | Push down the bottom plate until it locks into place. See Loading the multipurpose feeder for an illustration. | p.196 | |
| Job prints from the wrong paper source or on the wrong print media. | Check the Paper Type setting in the Paper Menu from the printer operator panel and in the printer driver. | p.196 | |
| Printer does not duplex pages. | • Make sure Duplex is selected in either the Finishing Menu or the program you are printing from. • Make sure you have enough printer memory installed. | p.196 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.