Instruction/ maintenance manual of the product M7011 Axis Communications
Go to page of 61
AXIS M7 0 1 1 Video Encoder User Manual.
About this Document This manual is intended for administrators and users of AXIS M7 0 1 1 Video Encoder , and is applicable to rmware 5.75 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product.
있 습 니 다 . 적 절히 접 지 된 STP (shielded twisted p air) 케이 블 을 사 용 하 여 제 품 을 연 결 하 십 시 오 . Safety This product complies with IEC/EN/UL 60950-1, Safety of Information Technology Equipment.
AXIS M7011 Video Encoder Safety Infor mation Safety Infor mation Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury .
AXIS M7011 Video Encoder T able of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS M7011 Video Encoder T able of Contents Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Symptoms, P ossible Causes and Remedial Actions . . . . . . . . . . . . . . . . . . . . . 55 Technical Specications .
AXIS M7011 Video Encoder Hardware Overview Hardware Overview 2 3 4 5 6 1 7 1 LED indicators for status, power , network 2 microSD/microSDHC/microSDXC slot supporting memory card up to 64 GB (card not .
AXIS M7011 Video Encoder Hardware Overview RS485/RS422 Connector Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as PTZ devices. SD Card Slot For SD card recommendations, see www .axis.com Control Button For location of the control button, see Hardware Overview on page 7 .
AXIS M7011 Video Encoder Access the Product Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers.
AXIS M7011 Video Encoder Access the Product For T echnical notes on this and other topics, visit the Axis Support web at www .axis.com/techsup Set the Root P assword To access the Axis product, you must set the password for the default administrator user root .
AXIS M7011 Video Encoder Access the Product 3. From the T rigger drop-down list, select Input Signal . 4. From the second drop-down list, select Manual Trigger . 5. Select the desired action and congure the other settings as required. For more information about action rules, see Events on page 33 .
AXIS M7011 Video Encoder Access the Product Focus bar – Use the arrows to focus the camera, or click on a position on the bar to set the focus position. Using the focus bar will disable the product’s autofocus. T o re-enable, use the PTZ control panel which is opened by clicking the Ctrl panel button (see above).
AXIS M7011 Video Encoder Media Streams Media Streams The Axis product provides several video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream proles.
AXIS M7011 Video Encoder Media Streams The AMC Control P anel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control P anel is automatically installed on rst use, after which it can be congured.
AXIS M7011 Video Encoder Media Streams Note • <ip>= IP address • The Axis product supports QuickTime 6.5.1 and later . • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS M7011 Video Encoder Set Up the Product Set Up the Product The Axis product can be congured by users with administrator or operator rights. T o open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings.
AXIS M7011 Video Encoder Video Video It is possible to congure the following video features in your Axis product: • Video stream. See page 17 . • Stream proles. See page 18 . • Camera settings. See page 19 . • Overlay image. See page 20 .
AXIS M7011 Video Encoder Video • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a xed amount. Alternatively , the frame rate can be set as Unlimited , which means the Axis product always delivers the highest frame rate possible under the current conditions.
AXIS M7011 Video Encoder Video • When setting up recording using action rules. See Events on page 33 . • When setting up continuous recording. See Continuous Recording on page 39 . • In the Live View page – select the stream prole from the Stream prole drop-down list.
AXIS M7011 Video Encoder Video Overlay Overlays are used to provide extra information, for example for forensic video analysis or during product installation and conguration. Overlays are superimposed over the video stream. An overlay text can display the current date and time, or a text string.
AXIS M7011 Video Encoder Video - To scale the image automatically , select Scale with resolution . The image will be scaled down to t the resolution used by the Axis product. 5. Click Save . To select the image to use as overlay: 1. Go to Video > Overlay Image .
AXIS M7011 Video Encoder Video The Privacy Mask List ( Video > Privacy Mask ) shows all the masks that are currently congured in the Axis product and indicates if they are enabled. Y ou can add a new mask, re-size the mask with the mouse, choose a color for the mask, and give the mask a name.
AXIS M7011 Video Encoder Configure the Live View Page Configure the Live View Page Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole.
AXIS M7011 Video Encoder Configure the Live View Page • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer . The recordings are saved to the location specied in the AMC Control P anel.
AXIS M7011 Video Encoder PTZ (Pan T ilt Zoom) PTZ (Pan T ilt Zoom) The PTZ menu is available if a PTZ driver has been uploaded. See Install PTZ Driver on page 27 . Preset P ositions A preset position is a saved view that can be used to quickly steer the camera to a specic position.
AXIS M7011 Video Encoder PTZ (Pan T ilt Zoom) 1. Go to PTZ > Guard Tour and click Add . 2. Enter a descriptive name. 3. Specify the pause length between runs. 4. Select an available preset position and click Apply . 5. Specify the Move Speed . 6. Specify the View Time in seconds or minutes.
AXIS M7011 Video Encoder PTZ (Pan T ilt Zoom) Note Disabling PTZ controls will not affect preset positions. For example, if the tilt control is disabled, the product can still move to preset positions that require a tilt movement.
AXIS M7011 Video Encoder Detectors Detectors Camera T ampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, spray-painted or severely defocused. T o send an alarm, for example an email, an action rule must be set up.
AXIS M7011 Video Encoder Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window .
AXIS M7011 Video Encoder Detectors Note • To trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • To avoid triggering on small objects, select a high object size.
AXIS M7011 Video Encoder Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting.
AXIS M7011 Video Encoder Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings .
AXIS M7011 Video Encoder Events Events The Event pages allow you to congure the Axis product to perform actions when different events occur . For example, the product can start a recording or send an email notication when motion is detected. The set of conditions that denes how and when the action is triggered is called an action rule.
AXIS M7011 Video Encoder Events - Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notications. - Motion Detection – T rigger the rule when motion is detected.
AXIS M7011 Video Encoder Events - Preset P osition – Go to a preset position. - Guard T our – Start a guard tour . See Guard T our on page 25 . • Record Video – Record video to a selected storage. • Send Images – Send images to a recipient.
AXIS M7011 Video Encoder Events HTTP Send Images Send Notication Send Video Clip HTTPS Send Images Send Notication Send Video Clip Encrypted le transfer using HyperText T ransfer Protocol Secure (HTTPS). Specify login information for the HTTPS server and validate the server’s certicate.
AXIS M7011 Video Encoder Events 3. Click OK . To use the schedule in an action rule, select the schedule from the Schedule drop-down list in the Action Rule Setup page. Set Up Recurrences Recurrences are used to trigger action rules repeatedly , for example every 5 minutes or every hour .
AXIS M7011 Video Encoder Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 39 . • To set up action rules, see page 33 . • To access recordings, see Find Recordings on page 38 .
AXIS M7011 Video Encoder Recordings 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the lters. See also Find Recordings on page 38 . 3. Select the recording and click Play .
AXIS M7011 Video Encoder Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. T o switch languages, go to Setup > Languages and rst upload the new language le.
AXIS M7011 Video Encoder System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords.
AXIS M7011 Video Encoder System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally , click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection P olicy for the different user groups.
AXIS M7011 Video Encoder System Options A Server/Client certicate can be self-signed or issued by a Certicate Authority (CA). A self-signed certicate offers limited protection and can be used before a CA-issued certicate has been obtained.
AXIS M7011 Video Encoder System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP . The IPv4 settings are congured under System Options > Network > TCP/IP > Basic .
AXIS M7011 Video Encoder System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar . 6. Open a browser and type http://<IP address> in the Location/Address eld.
AXIS M7011 Video Encoder System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > T CP/IP > Advanced . Select Obtain NTP server address via DHCP to use the NTP settings provided by the DHCP server .
AXIS M7011 Video Encoder System Options Use manually selected NAT router - Select this option to manually select a NAT router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NAT routers on your network.
AXIS M7011 Video Encoder System Options Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.
AXIS M7011 Video Encoder System Options Storage SD Card NO NO NO TICE TICE TICE To prevent data corruption, the SD card should be unmounted before removal. Note For SD card recommendations see www .axis.com The Axis product supports microSD/microSDHC/microSDXC cards.
AXIS M7011 Video Encoder System Options To enable automatic formatting, follow these steps: 1. Open the Axis product’s webpages and go to Setup > System Options > Storage . 2. Click SD Card . 3. Under General Settings , select Autoformat to . 4.
AXIS M7011 Video Encoder System Options • Generic T CP/IP allows the Axis product to receive data and send commands via T CP/IP . Select the desired Port T ype from the drop-down list. For more information, see the online help . Maintenance The Axis product provides several maintenance functions.
AXIS M7011 Video Encoder System Options Access Log - Lists all failed attempts to access the product. The Access Log can also be congured to list all connections to the product (see below). Server Report - Provides information about the product status in a pop-up window .
AXIS M7011 Video Encoder System Options Note The installation and management software tools are available from the support pages on www .axis.com/techsup To reset the product to the factory default settings: 1. Disconnect power from the product. 2. Press and hold the control button and reconnect power .
AXIS M7011 Video Encoder Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version.
AXIS M7011 Video Encoder Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www .
AXIS M7011 Video Encoder Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control ( Internet Explorer only ) To enable the updating of video images in Internet Explorer , set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer .
AXIS M7011 Video Encoder Troubleshooting Motion Detection triggers unexpectedly Changes in luminance Motion detection is based on changes in luminance in the image. This means that if there are sudden changes in the lighting, motion detection may trigger mistakenly .
AXIS M7011 Video Encoder T echnical Specifications T echnical Specifications Video Video compression H.264 (MPEG-4 P art 10/A VC) Baseline, Main and High prole Motion JPEG Resolutions 176x120 to 720x576 Frame rate H.
AXIS M7011 Video Encoder T echnical Specifications Approvals EN 550 22 Class B, EN 6 1 000-3-2, EN 6 1 000-3-3, EN 55024, EN 6 1 000-6-1, EN 6 1 000-6-2, FCC P art 15 Subpart B Class A+B, ICES-003 Class B, VCCI Class B, C-tick AS/NZS CISPR 22 Class B, KCC KN22 Class B, KN24, IEC/EN/UL 60950-1, CE, RoHS, WEEE, REACH Dimensions 90 x 29 x 38 mm (3.
AXIS M7011 Video Encoder T echnical Specifications • Using HTTPS may reduce frame rate, in particular if streaming Motion JPEG. • Heavy network utilization due to poor infrastructure. Bandwidth affected. • Viewing on poorly performing client computers lowers perceived performance.
User Manual V er . M1.6 AXIS M70 1 1 Video Encoder Date: April 20 15 © Axis Communications AB, 20 15 P art No. 63 149.
An important point after buying a device Axis Communications M7011 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Axis Communications M7011 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Axis Communications M7011 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Axis Communications M7011 you will learn all the available features of the product, as well as information on its operation. The information that you get Axis Communications M7011 will certainly help you make a decision on the purchase.
If you already are a holder of Axis Communications M7011, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Axis Communications M7011.
However, one of the most important roles played by the user manual is to help in solving problems with Axis Communications M7011. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Axis Communications M7011 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
