EN
LevelOne logo
Official user manual

LevelOne LevelOne

75 pages·2.8 MB·Security Camera·PDF·ENDEFRITNLJA
LevelOne LevelOne
Table of Contents 80 sections LevelOne · FCS-1060/WCS-2060 · P/T/Z IP Network Camera · User Manual · … ShowHide
LevelOnep.1FCS-1060/WCS-2060p.1P/T/Z IP Network Camerap.1User Manualp.1Before You Use This Productp.2Package Contentsp.5Installationp.6Hardware installationp.6To install in Ethernetp.7To install in wireless LAN (WCS-2060 Only)p.7Software Installationp.8刪除 :p.10Check Network Settingsp.11Add Password to Prevent Unauthorized Accessp.12How to Usep.13Authenticationp.13Installing plug-inp.14Primary user’s capabilityp.15Main Screen with Camera Viewp.15The Configuration:p.15The camera view:p.15View capabilitiesp.16The pan/tilt control buttons:p.17Client settingsp.19Administrator’s capabilityp.21Fine-tuning for Best Performancep.21For Viewing by Mobile Phonep.21For Best Real-time Video Imagesp.22Only Quality Images Will Dop.22Somewhere Between Real-time and Clear Imagesp.22Opening accounts for new usersp.23Protect Network Camera by passwordsp.23Build a security applicationp.23格式化: 項目符號及編號p.24Software revision upgradep.24Definitions in Configurationp.26System parametersp.27Security settingsp.28Network settingsp.29Network typep.29HTTPp.29RTSP Streamingp.30WLAN Configuration (WCS-2060 Only)p.31▶ “TKIP”p.32▶ “AES”p.32DDNSp.33Access Listp.34Audio and Videop.35Generalp.35Video Settingsp.35Video orientationp.35Audio settingsp.36Image Settingsp.37Camera Controlp.38Camera control areap.38Preset function areap.39Email & FTPp.40Emailp.40FTPp.40Motion detectionp.42Application settingsp.43Snapshotp.43Weekly schedulep.43Snapshot file name prefixp.43Send out the snapshot while motion detectionp.43Sequential operationp.43Method for sending snapshotp.44System logp.45Viewing system parametersp.46Maintenancep.47Appendixp.48A. Troubleshootingp.48Status LEDp.48Reset and restorep.48RESTORE:p.48B. URL commands of the Network Camerap.49Get server parameter valuesp.49Set server parameter valuesp.50Available parameters on the serverp.51NAME VALUE DESCRIPTIONp.51
Page 1 of the LevelOne LevelOne user manual — LevelOne
Page 1 · click to enlarge
Page 1
LevelOne LevelOne — LevelOne diagram (page 1)
Fig. 1 · LevelOne

LevelOne

FCS-1060/WCS-2060

P/T/Z IP Network Camera

User Manual

Ver 1.0.1 - 0606

Page 2 of the LevelOne LevelOne user manual — Before You Use This Product
Page 2 · click to enlarge
Page 2

Before You Use This Product

The use of surveillance devices may be prohibited by law in your country. The Network Camera is

not only a high-performance web-ready camera but also can be part of a flexible surveillance

system. It is the user’s responsibility to ensure that the operation of such devices is legal before

installing this unit for its intended use.

It is important to first verify that all contents received are complete according to the list in the

"Package Contents" chapter. Take notice of the warnings in “Quick installation guide” before the

Network Camera is installed, then carefully read and follow the instructions in the “Installation”

chapter to avoid damages due to faulty assembly and installation. This also ensures the product is

used properly as intended.

The Network Camera is a network device and its use should be straightforward for those who

have basic network knowledge. The “Troubleshooting” chapter in the Appendix provides remedies

to the most common errors in set up and configuration. You should consult this chapter first if you

run into a system error.

The Network Camera is designed for various applications including video sharing, general

security/surveillance, etc. The “How to Use” chapter suggests ways to best utilize the Network

Camera and ensure proper operations. For the creative and professional developers, the "URL

Commands of The Network Camera" chapter serves to be a helpful reference to customize

existing homepages or integrating with the current web server.

For paragraphs preceded by

the reader should use caution to understand

completely the warnings. Ignoring the warnings may result in serious hazards or

injuries.

Page 3 of the LevelOne LevelOne user manual — Before You Use This Product
Page 3 · click to enlarge
Page 3
Page 3 of the LevelOne LevelOne user manual — Before You Use This Product
Page 4 of the LevelOne LevelOne user manual — Before You Use This Product
Page 4 · click to enlarge
Page 4
Page 4 of the LevelOne LevelOne user manual — Before You Use This Product
Page 5 of the LevelOne LevelOne user manual — Package Contents
Page 5 · click to enlarge
Page 5

Package Contents

z Dipole Antenna (WCS-2060 Only)

z Mounting kit & pads

z Quick Installation Guide

z FCS-1060/WCS-2060 · z Power Adapter · z CD Manual/Utility

Page 6 of the LevelOne LevelOne user manual — Hardware installation
Page 6 · click to enlarge
Page 6

Installation

In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator"

refers to the person who can configure the Network Camera and grant user access to the camera.

Hardware installation

LevelOne LevelOne — Hardware installation diagram (page 6)
Fig. 2 · Hardware installation

Connect the power adapter jack to the Network

Camera before plugging in to the power socket. This will

reduce the risk of accidental electric shock.

Please verify that your product package contains all the accessories listed in the foregoing Package Contents.

Depending on the user’s application, an Ethernet cable may be needed.

The Ethernet cable should meet the specs of UTP Category 5 and not exceed 100 meters in length.

Upon powering up, the front red LED will become lighted first and then the device will go through

booting process. During the booting process, red, blue and green LEDs will be on. After booted,

the Network Camera will standby for getting IP address. After getting IP Address, the green LED

will blink every second.

The Network Camera will first detect Ethernet. If it does not connect to Ethernet, the Network

Page 7 of the LevelOne LevelOne user manual — To install in wireless LAN (WCS-2060 Only)
Page 7 · click to enlarge
Page 7

Camera will try WLAN. During the searching and connecting process to the wireless access point

or station, the red LED of the Network Camera will flash every second. Until the Network Camera

connects to the other wireless device, the red LED will become lighted. Operating in either

network mode, the green LED will flash every second as heartbeat to indicate alive. If the red LED

is blinking, please check the network connections.

To install in Ethernet

Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet cable plug

in the power adapter. If the LED turns out to be steady blue, go to next paragraph “Software

installation”. If the Ethernet is not available, Network Camera will switch to wireless LAN mode.

To install in wireless LAN (WCS-2060 Only)

If the Ethernet is not available while power on, the Network Camera will search for any access

point with the SSID “default”. Once any access point is found, the LED will turn blue to wait for

installation. If the network environment cannot meet the default settings, install Network Camera

in Ethernet to proceed with wireless LAN configuration.

Page 8 of the LevelOne LevelOne user manual — Software Installation
Page 8 · click to enlarge
Page 8

Software Installation

In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator"

refers to the person who can configure the Network Camera and grant user access to the camera.

At the end of the hardware installation, the Administrator must place the product software CD into

the CD-ROM drive of the PC running in MS Windows. An auto-run program will pop up (If the

program is not on auto-run, go to the root directory of the software CD and click on “autorun.exe”).

LevelOne LevelOne — Software Installation diagram (page 8)
Fig. 3 · Software Installation
Page 9 of the LevelOne LevelOne user manual — Software Installation
Page 9 · click to enlarge
Page 9

Click on “Install Software” after the window contains changed, click on “Installation Wizard” to run

installation program.

LevelOne LevelOne — Software Installation diagram (page 9)
Fig. 4 · Software Installation

Upon Installation Wizard’s start up, a searching box will pop up. This program searches for IP

Network Camera on the same LAN:

After searching, Network Cameras will be located by the Installation Wizard. There may be

several entries shown in the window. The Administrator may differentiate the Network Cameras

with the MAC address.

LevelOne LevelOne — Software Installation diagram (page 9)
Fig. 5 · Software Installation
Page 10 of the LevelOne LevelOne user manual — 刪除 :
Page 10 · click to enlarge
Page 10

For the MAC address in the “MAC address” field, please check the label on the bottom of the

camera.

LevelOne LevelOne — 刪除 : diagram (page 10)
Fig. 6

The IP addresses shown in the "Current IP Address" field reflect those on the local network. They

may be from the DHCP server. If there is no DHCP server, the camera will try to find a free IP

address (this takes from 15 second to 3 minutes, depending on the LAN status). The method of

finding IP address is seeking from 192.168.0.99, to 192.168.0.254. If any of the address inside

this range is free, the Network Camera will be assigned to this IP address, and its subnet mask

would be 255.255.255.0. If none of the addresses is free, the Network Camera will try the range

from 192.168.0.2 to 192.168.0.98. After an IP address is assigned to the camera, the “Activity”

status LED blinks.

The UPnP function will always assign an IP address for the Network Camera. The Administrator

can click on button “Link to selected device” to connect the I.E. to the camera.

刪除 :

If the camera is not on the IP installer list, click on the “Search” button to search for the camera on

the LAN.

Page 11 of the LevelOne LevelOne user manual — Check Network Settings
Page 11 · click to enlarge
Page 11
LevelOne LevelOne — Check Network Settings diagram (page 11)
Fig. 7 · Check Network Settings

For more detailed usage of the Installation Wizard, please refer to the user manual of

the Installation Wizard included in the product CDROM to find the location of the

Network Camera. There may be many Network Cameras in the local network. Users

can differentiate the Network Cameras with the MAC address. The MAC address is

printed on the back of the Network Camera body. Initial Access to the Network Camera

Check Network Settings

FCS-1060/WCS-2060 IP Network Camera can be connected either before or immediately after

software installation onto the Local Area Network. The Administrator should complete the network

settings on the configuration page, including the correct subnet mask and IP address of gateway

and DNS. Ask your network administrator or Internet service provider for the detail information. By

default the Network Camera requires the Administrator to run installation every time it reboots. If

the network settings are to remain unchanged, disable the Install option. Refer to “Network

settings” on the System Configuration page for details. If any setting is entered incorrectly and

cannot proceed to setting up the Network Camera, restore the factory settings following the steps

Page 12 of the LevelOne LevelOne user manual — Add Password to Prevent Unauthorized Access
Page 12 · click to enlarge
Page 12

in the “Troubleshooting” chapter of the Appendix.

Add Password to Prevent Unauthorized Access

The default Administrator’s password is blank and the Network Camera initially will not ask for any

password. The Administrator should immediately implement a new password as a matter of

prudent security practice. Once the Administrator’s password is saved, the Network Camera will

ask for the user’s name and password before each access. The Administrator can set up a

maximum of twenty (20) user accounts. Each user can access the Network Camera except to

perform system configuration. Some critical functions are exclusive for the Administrator, such as

system configuration, user administration, and software upgrades. The user name for the

Administrator is permanently assigned as “root”. Once the password is changed, the browser will

display an authentication window to ask for the new password. Once the password is set, there

is no provision to recover the Administrator’s password. The only option is to restore to

the original factory default settings.

Page 13 of the LevelOne LevelOne user manual — Authentication
Page 13 · click to enlarge
Page 13

How to Use

Authentication

After opening the Web browser and typing in the URL of the Network Camera, a dialogue window

pops up to request a username and password. Upon successful authentication, the following

figure is displayed.

LevelOne LevelOne — Authentication diagram (page 13)
Fig. 8 · Authentication

*If the administrator (root user) assigns no password, everybody can access the homepage

directly.

Page 14 of the LevelOne LevelOne user manual — Installing plug-in
Page 14 · click to enlarge
Page 14

Installing plug-in

For the initial access to the Network Camera in Windows, the web browser may prompt for

permission to install a new plug-in for the Network Camera. Permission request depends on the

Internet security settings of the user’s PC or notebook. If the highest security level is set, the

computer may prohibit any installation and execution attempt. This plug-in has been registered for

certificate and is used to display the video in the browser. Users may click on

proceed. If the web browser does not allow the user to continue to install, check the Internet

security option and lower the security levels or contact your IT or networking supervisor for help.

LevelOne LevelOne — Installing plug-in diagram (page 14)
Fig. 9 · Installing plug-in

to

Page 15 of the LevelOne LevelOne user manual — The camera view:
Page 15 · click to enlarge
Page 15

Primary user’s capability

Main Screen with Camera View

The main page layout has three parts:

Configuration functions: The camera can be configured using these user interfaces.

Camera View: What the camera sees.

Pan/Tilt control buttonsThese buttons provide a command interface to control the aim of the

camera.

Click on the configuration link to the left of the image window to enter the configuration page.

LevelOne LevelOne — Main Screen with Camera View diagram (page 15)
Fig. 10 · Main Screen with Camera View

The Configuration:

“Snapshot” The button provides users a fast way to capture a single image of the video from the

Network Camera.

Clicking on this button links you to the client setting pages, please check the following session for

more details.

“Configuration” Only the Administrator can access camera configurations.

The camera view:

The information bar at the top of the camera view shows the connection type to the Network

Camera and the current date/time.

“Client Settings”

Page 16 of the LevelOne LevelOne user manual — View capabilities
Page 16 · click to enlarge
Page 16

The camera view provides not only the live video, but also a way to aim the Network Camera to

different target. Using mouse to click on the target inside the video will command the Network

Camera to aim at the target.

LevelOne LevelOne — View capabilities diagram (page 16)
Fig. 11 · View capabilities
LevelOne LevelOne — View capabilities diagram (page 16)
Fig. 12 · View capabilities

View capabilities

This feature allows users to open a digital zoom control window to specify the zoom factor for

specified area in the camera view. Users can also move the white frame to select the area of the

video that she/he wants to view.

“Disable digital zoom” The checkbox selection allows users to disable/enable the digital zoom

function.

“Zoom Factors” The range of zoom factor is from 100% to 400%, users can select any integer

factor inside this area.

“Hide” Click on this button can close the digital zoom control window.

Page 17 of the LevelOne LevelOne user manual — The pan/tilt control buttons:
Page 17 · click to enlarge
Page 17
LevelOne LevelOne — The pan/tilt control buttons: diagram (page 17)
Fig. 13 · The pan/tilt control buttons:

“Play” The option will connect to the Network Camera. The button is the same one as “Pause”.

“Pause” The option will pause the video, but the connection remains. The button is the same one

as “Play”.

“Stop” The option will disconnect to the Network Camera.

“Play volume” Click on this button can adjust the audio volume.

“Mute” Disable audio at client side.

The pan/tilt control buttons:

The direction buttons are for Left, Right, Up, Down, and Home functions. The Home button

centers the camera.

“Go to” Once the Administrator has determined the preset positions; the User can aim the

camera using this control.

This button sets the moving range of the “Left” and “Right” commands.

This button sets the moving range of the “Up” and “Down” commands.

Show 7 more labels / short text on this page
Mute · Digital Zoom · Play volume · Play/Pause · Stop · “Pan speed” · “Tilt speed”
Page 18 of the LevelOne LevelOne user manual — The pan/tilt control buttons:
Page 18 · click to enlarge
Page 18

This button commands the camera to pan from the current position to the left-most and then to the

right-most position. After panning, the camera returns to the original position.

This button commands the camera to patrol between the preset positions on the Patrol List, which

can be modified on the “Camera control page”. After one patrol cycle, the camera returns to the

original position.

“Stop” This stop the “Auto Pan” command or “Auto Patrol” command.

“Pan” · “Patrol”

Page 19 of the LevelOne LevelOne user manual — Client settings
Page 19 · click to enlarge
Page 19

Client settings

At the initial access to the “Connection type” page in Windows, the web browser will ask for a new

plug-in installation, the plug-in being the Network Camera. This plug-in has been registered for

certification and can be used to change the parameters at the client’s site. The user may click on

to install the plug-in. If the web browser does not allow the user to complete the installation, check the Internet security to lower the security level or contact your IT or networking

supervisor.

LevelOne LevelOne — Client settings diagram (page 19)
Fig. 14 · Client settings

There are two settings for the client side. One is “Media Options” for users to determine the type

of media to be streaming. The other is “Protocol Options” which allows choices on connection

protocol between client and server. There are two protocols choices to optimize your usage –

UDP and TCP.

The UDP protocol allows for more real-time audio and video streams. However, some packets

may be lost due to network burst traffic and images may be obscured.

The TCP protocol allows for less packet loss and produces a more accurate video display. The

downside with this protocol is that the real-time effect is worse than that with the UDP protocol.

If no special need is required, UDP protocol is recommended. Generally speaking, the client’s

choice will be in the order of UDP → TCP. After the Network Camera is connected successfully,

“Protocol Option” will indicate the selected protocol. The selected protocol will be recorded in the

user's PC and will be used for the next connection. If the network environment is changed, or the

user wants to let the web browser to detect again, manually select the UDP protocol, save, and

return HOME to re-connect.

Page 20 of the LevelOne LevelOne user manual — Client settings
Page 20 · click to enlarge
Page 20

http://<Network Camera>/client.html

is the domain name or the original IP address of the Network Camera.

LevelOne LevelOne — Client settings diagram (page 20)
Fig. 15 · Client settings
Page 21 of the LevelOne LevelOne user manual — For Viewing by Mobile Phone
Page 21 · click to enlarge
Page 21

Administrator’s capability

Fine-tuning for Best Performance

Best performance generally equates to the fastest image refresh rate with the best video quality,

and at the lowest network bandwidth as possible. The three factors, “Maximum frame rate”,

“Constant bit rate”, and “Fix quality” on the Audio and Video Configuration page, are correlative to

allow for achieving the best performance possible.

LevelOne LevelOne — Fine-tuning for Best Performance diagram (page 21)
Fig. 16 · Fine-tuning for Best Performance

For Viewing by Mobile Phone

Most 3GPP cell phone supports media streaming with MPEG4 video and GSM-AMR audio. Due

to the limitation of the bandwidth for 3GPP, only 176x144 size video is supported for cell phone

viewing. Select the “Configure for mobile viewing” option will change the range of other related

video settings.

Page 22 of the LevelOne LevelOne user manual — Somewhere Between Real-time and Clear Images
Page 22 · click to enlarge
Page 22

For Best Real-time Video Images

To achieve good real-time visual effect, the network bandwidth should be large enough to allow a

transmission rate of greater than 20 image frames per second. If the broadband network is over 1

Mbps, set the “Fix bit rate” to 1000Kbps or 1200Kbps. The maximum frame rate is 30. If your

network bandwidth is more than 512Kbps, you can fix the bit rate according to your bandwidth and

set the maximum frame rate to 30 fps. If the images vary dramatically in your environment, you

may want to slow the maximum frame rate down to 20 fps in order to lower the rate of data

transmission. This allows for better video quality and the human eyes cannot readily detect the

differences between those of 20, 25, or 30 frames per second. If your network bandwidth is below

512 Kbps, set the “Fix bit rate” according to your bandwidth and try to get the best performance by

fine-tuning with the “Maximum frame rate”. In a slow network, greater frame rate results in blur

images. Another work-around is to choose “160x120” in the “Size” option for better images. Video

quality performance will vary somewhat due to the number of users viewing on the network; even

when the parameters have initially been finely tuned. Performance will also suffer due to poor

connectivity because of the network’s burst constraint.

Only Quality Images Will Do

To have the best video quality, you should set “Fix quality” at “Detailed” or “Excellent” and adjust

the “Maximum frame rate” to match your network’s bandwidth. If your network is slow and you

receive “broken” pictures, go to the TCP protocol in “Connection type” and choose a more

appropriate mode of transmission. The images may suffer a time delay due to a slower connection.

The delay will also increase with added number of users.

Somewhere Between Real-time and Clear Images

If you have a broadband network, set “Fix quality” at ”Normal” or better, rather than setting “Fix bit

rate”. You can also fix the bandwidth according to your actual network speed and adjust the frame

rate. Start from 30 fps down for best results but not below 15 fps. If the image qualities are not

improved, select a lower bandwidth setting.

Page 23 of the LevelOne LevelOne user manual — Build a security application
Page 23 · click to enlarge
Page 23

Opening accounts for new users

LevelOne LevelOne — Opening accounts for new users diagram (page 23)
Fig. 17 · Opening accounts for new users

Protect Network Camera by passwords

The Network Camera is shipped without any password by default. That means everyone can

access the Network Camera including the configuration as long as the IP address is known. It is

necessary to assign a password if the Network Camera is intended to be accessed by others.

Type a new word twice in ○1 to enable protection. This password is used to identify the

administrator. Then add an account with user name and password for your friends in ○2. Network

Camera can provide twenty accounts for your valuable customers or friends. You may delete

some users from ○3.

Build a security application

The Administrator can use the built-in motion detection to monitor any movement to perform many

Page 24 of the LevelOne LevelOne user manual — 格式化: 項目符號及編號
Page 24 · click to enlarge
Page 24

useful security applications. To upload the snapshots, users can choose either email or FTP

according to user’s needs. Both e-mail and FTP use the network settings on the Email and FTP

page. Refer to the definition section for detail configuration.

1. Click on “ Configuration ” on homepage,
2. Click on “ Motion detection ” at the left column,
3. Check “Enable motion detection”,
4. Click on new to have a new window to monitor video,
5. Type in a name to identify the new window,
6. Use the mouse to click, hold, and drag the window corner to resize or the title bar to move,
7. Fine-tune using the “Sensitivity” and “Percentage” fields to best suit the camera’s environment.

Higher ”Sensitivity” detects the slighter motion. Higher “Percentage” discriminates smaller

8. Clicking on “Save” enables the activity display. Green means the motion in the window is

under the watermark set by Administrator and red means it is over the watermark,

9. Click on “ Application ” at the left column,
10. Check the weekdays as you need and give the time interval to monitor the motion detection
11. Select the Trigger on Motion detection.
12. Set the delay before detecting next motion to avoid continuous false alarms following the
13. Set the number of pre-event and post-event images to be uploaded,
14. Check the window name set in step 5,
15. Check the way to upload snapshot,

Click on save to validate.

格式化: 項目符號及編號

Software revision upgrade

Customers can obtain the up-to-date software from the web site of LevelOne. An easy-to-use

Upgrade Wizard is provided to upgrade the Network Camera with just a few clicks. The upgrade

function is opened to the Administrator only. To upgrade the system, follow the procedures below.

1. Download the firmware file named “xxx.pkg” from the appropriate product folder.
2. Run the Upgrade Wizard and proceed following the prompts. Refer to the instructions of the

Upgrade Wizard for details.

3. Or upgrade firmware from HTTP web page directly
3. The whole process will finish in a few minutes and it will automatically restart the system.

objects, · every day, · original event,

Page 25 of the LevelOne LevelOne user manual — 格式化: 項目符號及編號
Page 25 · click to enlarge
Page 25

If power fails during the writing process of Flash memory, the program in the

memory of the Network Camera may be destroyed permanently. If the Network

Camera cannot restart properly, ask your dealer for technical service.

Page 26 of the LevelOne LevelOne user manual — Definitions in Configuration
Page 26 · click to enlarge
Page 26

Definitions in Configuration

Only the Administrator can access system configuration. Each category in the left column will be

explained in the following pages. The bold texts are the specific phrases on the Option pages. The

Administrator may type the URL below the figure to directly enter the frame page of configuration.

If the Administrator also wants to set certain options through the URL, read the reference

appendix for details.

LevelOne LevelOne — Definitions in Configuration diagram (page 26)
Fig. 18 · Definitions in Configuration

http://<Network Camera>/setup/config.html

is the domain name or original IP address of the Network Camera.

http://<Network Camera>/setup/system.html

is the domain name or original IP address of the Network Camera.

Page 27 of the LevelOne LevelOne user manual — System parameters
Page 27 · click to enlarge
Page 27

System parameters

"Host name" The text displays the title at the top of the main page.

“Turn off the LED indicator” Check this option to shut off the LED on the rear. It can prevent the

camera’s operation being noticed.

"Keep current date and time" Click on this to reserve the current date and time of the Network

Camera. An internal real-time clock maintains the date and time even when the power of the

system is turned off.

"Sync with computer time" Synchronizes the date and time of the Network Camera with the

local computer. The read-only date and time of the PC is displayed as updated.

“Manual” Adjust the date and time according to what is entered by the Administrator. Notice the

format in the related fields while doing the entry.

“Automatic” Synchronize with the NTP server over the Internet whenever the Network Camera

starts up. It will fail if the assigned time-server cannot be reached.

“NTP server” Assign the IP address or domain name of the time-server. Leaving the text box

blank connects the Network Camera to the default time-servers.

"Time zone" Adjust the time with that of the time-servers for local settings.

“Update interval” Select hourly, daily, weekly, or monthly update with the time on the NTP server.

Remember to click on

to immediately validate the changes. Otherwise, the correct time will

not be synchronized.

Page 28 of the LevelOne LevelOne user manual — Security settings
Page 28 · click to enlarge
Page 28

Security settings

“Root password” Change the Administrator’s password by typing in the new password

identically in both text boxes. The typed entries will be displayed as asterisks for security

purposes. After pressing

, the web browser will ask the Administrator for the new password

for access.

“Add user” Type the new user's name and password and press

to insert the new entry. The new user will be displayed in the user name list. There is a maximum of twenty user accounts.

“Manager user” Pull down the user list to find the user’s name and press

to complete.

http://<Network Camera>/setup/security.html

is the domain name or original IP address of the Network Camera.

Page 29 of the LevelOne LevelOne user manual — HTTP
Page 29 · click to enlarge
Page 29

Network settings

Any changes made on this page will restart the system in order to validate the changes. Make

sure every field is entered correctly before clicking on

Network type

The default type is LAN. Select PPPoE if using ADSL

"Get IP address automatically" & “Use fixed IP address”

The default status is “Get IP address automatically”. This can be tedious having to perform

software installation whenever the Network Camera starts. Therefore, once the network settings,

especially the IP address, have been entered correctly, select “Use fixed IP address” then the

Network Camera will skip installation at the next boot. The Network Camera can automatically

restart and operate normally after a power outage. Users can run IP installer to check the IP

address assigned to the Network Camera if the IP address is forgotten or using the UPnP function

provided by the Network Camera (MS Windows XP provides UPnP function at My Network

Place). “IP address” This is necessary for network identification.

“Subnet mask” This is used to determine if the destination is in the same subnet. The default

value is “255.255.255.0”.

“Default router” This is the gateway used to forward frames to destinations in a different subnet.

Invalid router setting will fail the transmission to destinations in different subnet.

“Primary DNS” The primary domain name server that translates hostnames into IP addresses.

“Secondary DNS” Secondary domain name server that backups the Primary DNS.

“Enable UPnP presentation” Enable the UPnP camera short cut

“Enable UPnP port forwarding” Enable uPnP port forwarding

“PPPoE” If using the PPPoE interface , fill the following settings from ISP

“User name” The login name of PPPoE account

“Password” The password of PPPoE account

“Confirm password” Input password again for confirmation

HTTP

“Http port” This can be other than the default Port 80. Once the port is changed, the users must

be notified the change for the connection to be successful. For instance, when the Administrator

changes the HTTP port of the Network Camera whose IP address is 192.168.0.100 from 80 to

“LAN” & “PPPoE”

Page 30 of the LevelOne LevelOne user manual — RTSP Streaming
Page 30 · click to enlarge
Page 30

8080, the users must type in the web browser “http://192.168.0.100:8080” instead of

“http://192.168.0.100”

RTSP Streaming

“Access name” This is the access URL for making connection from client software. Using

rtsp:/// to make connection

“RTSP port” This can be other than the default Port 554

LevelOne LevelOne — RTSP Streaming diagram (page 30)
Fig. 19 · RTSP Streaming

http://<Network Camera>/setup/network.html

is the domain name or original IP address of the Network Camera.

Page 31 of the LevelOne LevelOne user manual — WLAN Configuration (WCS-2060 Only)
Page 31 · click to enlarge
Page 31

WLAN Configuration (WCS-2060 Only)

“SSID” (Service Set Identifier), it is a name that identifies a wireless network. Access Points and

wireless clients attempting to connect to a specific WLAN (Wireless Local Area Network) must use

the same SSID. The default setting is default. Note: The maximum length of SSID is 32

single-byte characters and SSID can’t be any of “, <, > and space character.

“Wireless mode” Clicking on the pull-down menu to select from the following options:

▶ “Infrastructure” Make the Network Camera connect to the WLAN via an Access Point. (The

▶ “Ad-Hoc” Make the Network Camera connect directly to a host equipped with a wireless

adapter in a peer-to-peer environment.

“Channel” While in infrastructure mode, the channel is selected automatically to match the

channel setting for the selected Access Point. In Ad-Hoc mode, the channel must be manually set

to the same channel for each wireless adapter. The default channel setting depends on the

installed region.

“TX rate” This field is for selecting the maximum transmission rate on the network. The default

setting is “auto”, that is the Network Camera will try to connect to the other wireless device with

highest transmitting rate.

“Security” Select the data encrypt method

▶ “None” – No data encryption.

▶ “WEP” – allows communication only with other devices with identical WEP settings.

▶ “WPA-PSK” – Use WPA pre-shared key.

“Auth Mode” Choosing one of the following modes, (Open is the default setting).

▶ “Open” – communicates the key across the network.

▶ “Shared” – allows communication only with other devices with identical WEP settings.

“Key length” The administrator can select the key length among 64 or 128 bits. 64bits is the

default setting.

“Key format” Hexadecimal or ASCII. “HEX” is the default setting.

▶ “HEX” digits consist of the numbers 0~9 and the letters A-F.

▶ “ASCII” is a code for representing English letters as numbers from 0-127 except “, and

space characters that are reserved.

“Network Key” Entering a key in either hexadecimal or ASCII format. When selecting different

key length, acceptable input length is listed as following:

64 bits key length: 10 Hex digits or 5 characters.

128 bites key length: 26 Hex digits or 13 characters.

default setting)

Page 32 of the LevelOne LevelOne user manual — ▶ “TKIP”
Page 32 · click to enlarge
Page 32

ASCII format.

“Algorithm” Choosing one of the following algorithm for WPA-PSK modes

▶ “TKIP”

▶ “AES”

“Pre-shared Key” Entering a key in ASCII format. The length of the key is 8 ~ 63

Some invalid settings may cause the system failing to respond. Change the

configuration only if necessary and consult with your network supervisor or experienced

users for correct settings. Once the system has lost contact, refer to Appendix A for reset

and restore procedures.

LevelOne LevelOne — ▶ “TKIP” diagram (page 32)
Fig. 20

http://<Network Camera>/setup/wireless.html

is the domain name or original IP address of the Network Camera.

Page 33 of the LevelOne LevelOne user manual — DDNS
Page 33 · click to enlarge
Page 33

DDNS

“Enable DDNS” This option turns on the DDNS function.

“Provider” The provider list contains four hosts that provide DDNS services. Please connect to

the service provider’s website to make sure the service charges.

“Host Name” If the User wants to use DDNS service, this field must be filled. Please input the

hostname that is registered in the DDNS server.

“Username/E-mail” The Username or E-mail field is necessary for logging in the DDNS server or

notify the User of the new IP address. Note: when this field is input as “Username” the following

field must be input as “Password”.

“Password/Key” Please input the password or key to get the DDNS service.

“Save” Click on this button to save current settings for the DDNS service and UPnP function.

LevelOne LevelOne — DDNS diagram (page 33)
Fig. 21

http://<Network Camera>/setup/ddns.html

is the domain name or original IP address of the Network Camera.

Page 34 of the LevelOne LevelOne user manual — Access List
Page 34 · click to enlarge
Page 34

Access List

The access list is to control the access permission of clients by checking the client IP address.

There are two lists for permission control: Allow List and Deny List. Only those clients whose IP

address is in the Allow List and not in the Deny List can connect to the Network Camera for

receiving the audio/video streaming.

Both Allow List and Deny List consist of a list of IP ranges. If you want to add a new IP address

range, type the Start IP Address and End IP Address in the text boxes and click on the Add

button. If you want to remove an existing IP address range, just select from the pull-down menu

and click on the Delete button.

Both the Allow List and Deny List can have 20 entries.

LevelOne LevelOne — Access List diagram (page 34)
Fig. 22 · Access List

http://<Network Camera>/setup/accesslist.html

is the domain name or original IP address of the Network Camera.

Page 35 of the LevelOne LevelOne user manual — Video orientation
Page 35 · click to enlarge
Page 35

Audio and Video

General

“Configure for computer viewing” To make quick setting for computer viewing

“Configure for mobile viewing” To make quick setting for cell phone viewing

Video Settings

“Video title” The text string can be displayed on video

“Color” Select either for color or monochrome video display.

“Frame Size” There are four options for video sizes. “160x120”, “176x144”, “320x240”,

“640x480”.

“Power line frequency (for fluorescent light)”, the fluorescent light will flash according to the

power line frequency that depends on local utility. Change the frequency setting to eliminate

uncomfortable flash image when the light source is only fluorescent light.

There are three dependent parameters provided for video performance adjustment.

“key frame interval” The Key frame Interval setting determines how frequently a full frame of the

source video is preserved in the Timeline. For example, a Key frame interval of 24 will insert a

video key frame every 24th frame in the Timeline.

“Max frame rate” This limits the maximal refresh frame rate, which can be combined with the

“Video quality” to optimize bandwidth utilization and video quality. Choose “Constant bit rate” If

the user wants to fix the bandwidth utilization regardless of the video quality or choose “Fixed

quality” and select the desired bandwidth. The video quality may be poor due to the sending of

maximal frame rate within the limited bandwidth when images are moving rapidly. Consequently,

to ensure detailed video quality (quantization rate) regardless of the network, it will utilize more

bandwidth to send the maximal frames when images change drastically.

Video orientation

“Flip” Vertically rotate the video.

“Mirror” Horizontally rotate the video. Check options both if the Network Camera is installed

upside down.

“White balance” Adjust the value for best color temperature.

Page 36 of the LevelOne LevelOne user manual — Audio settings
Page 36 · click to enlarge
Page 36

Audio settings

“Audio type” Select audio codec “AAC” or “GSM-AMR” and the bit rate

http://<Network Camera>/setup/audiovideo.html

is the domain name or original IP address of the Network Camera.

“mute” Audio mute

Page 37 of the LevelOne LevelOne user manual — Image Settings
Page 37 · click to enlarge
Page 37

Image Settings

Click on this button to pop up another window to tune “Brightness”,

“Contrast”, “Hue” and

LevelOne LevelOne — Image Settings diagram (page 37)
Fig. 23 · Image Settings

compensation. Each field has

eleven levels ranged from -5

to +5. In “Brightness” and

“Contrast” fields the value 0

indicates auto tuning. The

to fine-tune the image. When

the image is O.K., press

to set the image

settings.

Click on this to recall the original

the changes.

“Saturation” for video · user may press · settings without incorporating

Page 38 of the LevelOne LevelOne user manual — Camera control area
Page 38 · click to enlarge
Page 38

Camera Control

LevelOne LevelOne — Camera Control diagram (page 38)
Fig. 24 · Camera Control

On the Camera Control page, there are two main function control areas:

Camera control area

The pan and tilt functions can be controlled with these buttons. The “Left” button aims the camera

to the left; the “Right”, “Up”, and “Down” buttons aim the camera accordingly. The “Home” button

aims the camera to the center.

“Pan speed” This controls the range of the horizontal movement of the camera. The greater the

value, the greater angular movement when performing the “Left” or “Right” functions.

“Tilt speed” This controls the range of the vertical movement of the camera. The greater the value,

the greater angular movement when performing the “Up” or “Down” functions would be.

“Auto pan/patrol speed” This defines the speed of panning and patrol, the greater the value, the

faster the speed.

Camera control · area · Preset function area

Page 39 of the LevelOne LevelOne user manual — Preset function area
Page 39 · click to enlarge
Page 39

Preset function area

”Current position”, If the User wants to save the current view as a preset location, enter a name

for each of the current video view at “current position” and click on the “Add” button. The camera

allows for 20 preset locations.

”Preset position” This keeps a list for preset positions. Clicking on the “Delete” button will

remove the current selected position from the preset list.

“Set as home” Click on the button will set the current aimed position as home of the Network

Camera. Each time the Network Camera reboots or after calibration, it will automatically aim to the

defined home position.

“Default home” Restore home position to factory default home by clicking on this button.

”Dwelling time” The value set here specifies:

1. The stop time of each preset location during auto patrol of the Network Camera.
2. The stay time at the most left and the most right positions when the Network Camera is doing

auto panning.

”Patrol selection”, After the User has saved a list of preset positions, the “Preset locations” box

will also keep a list of the preset positions. And once the “Select>” button is clicked, the “Selected

location” box will keep a list of the patrol stops. The “Remove” button removes the preset

position from the patrol stops. The “UP”, “DOWN” buttons adjust the order of the patrol stops.

Several preset positions can be added to the patrol stops. The camera can accept up to 40 patrol

stops.

“Save” button

The button is valid for “Auto pan/patrol speed”, “Enable IR control”, “Dwelling time” and “Patrol

selections”. In other words, after changing these settings, and the “Save” button is not clicked,

the new setting of the camera will not take effect.

Page 40 of the LevelOne LevelOne user manual — FTP
Page 40 · click to enlarge
Page 40

Email & FTP

Email

When the SMTP server support SMTP authentication, users need to give the valid user name and

password to send email via the server.

“Sender email address”, the email address of the sender.

There are two external mail server can be configured, primary and secondary email server, The

network camera will use primary server as default , and use secondary server when primary

server is unreachable.

“Server address” The domain name or IP address of the external email server.

“User name” This granted user name on the external email server.

“Password” This granted password on the external email server.

“Recipient email address” The email address of the recipients for snapshots or log file. Multiple

recipients must be separated by semicolon, ‘;’.

FTP

“Built-in FTP server port number” This can be other than the default port 21. The user can

change this value from 1025 to 65535. After the changed, the external FTP client program must

change the server port of connection accordingly.

There are two external FTP server can be configured, primary and secondary FTP server, The

network camera will use primary server as default , and use secondary server when primary

server is unreachable.

“Server address” The domain name or the IP address of the external FTP server. The following

user settings must be correctly configured for remote access.

“FTP server port” This can be other than the default port 21. The user can change this value

from 1025 to 65535.

“User name” Granted user name on the external FTP server.

“Password” Granted password on the external FTP server.

“Remote folder name” Granted folder on the external FTP server. The string must conform to

that of the external FTP server. Some FTP servers cannot accept preceding slash symbol before

Page 41 of the LevelOne LevelOne user manual — Email & FTP
Page 41 · click to enlarge
Page 41

the path without virtual path mapping. Refer to the instructions for the external FTP server for

details. The folder privilege must be open for upload.

LevelOne LevelOne — Email & FTP diagram (page 41)
Fig. 25 · Email & FTP

http://<Network Camera>/setup/mailftp.html

is the domain name or original IP address of the Network Camera.

Page 42 of the LevelOne LevelOne user manual — Motion detection
Page 42 · click to enlarge
Page 42

Motion detection

“Enable motion detection” Check this option to turn on motion detection.

Click on this button to add a new window. At most three windows can exist simultaneously. Use the mouse to click, hold, and drag the window frame to resize or the title bar to move. Clicking

on the ‘x’ at the upper right-hand corner of the window to delete the window. Remember to save in

order to validate the changes.

Click on this button to save the related window settings. A graphic bar will rise or fall

depending on the image variation. A green bar means the image variation is under monitoring

level and a red bar means the image variation is over monitoring level. When the bar goes red, the

detected window will also be outlined in red. Going back to the homepage, the monitored window

is hidden but the red frame shows when motion is detected.

"Window Name" The text will show at the top of the window.

“Sensitivity” This sets the endurable difference between two sequential images.

“Percentage” This sets the space ratio of moving objects in the monitoring window. Higher

sensitivity and small percentage will allow easier motion detection.

The following figure shows the screen when

is clicked. The monitoring window has been

outlined in red and the graphic bar goes red since the goldfish is moving.

LevelOne LevelOne — Motion detection diagram (page 42)
Fig. 26 · Motion detection
Page 43 of the LevelOne LevelOne user manual — Sequential operation
Page 43 · click to enlarge
Page 43

Application settings

Snapshot

“Enable snapshot” Enable/Disable snapshot application.

Weekly schedule

“Sun” ~ “Sat” Select the days of the week to perform the application.

Select “Always” or input the time interval.

Snapshot file name prefix

The prefix name will be added on the file name of the snapshot images.

Send out the snapshot while motion detection

There are three windows for motion detection each can be assigned a name. Select the windows

which need to be monitored. If motion detection has not been set up, “undefined” will be shown

instead of the window title. If this happens, clicking on “Motion detection” and a note will show to

direct the User to the configuration page for motion detection.

“Send pre-event image(s)” The number of pre-snapshots will be captured and send when a

condition is triggered.

“Send post-event image(s)” The number of post-snapshots will be captured and send when a

condition is triggered.

“Delay second(s) before detecting next motion” Set the time delay before restarting to check

on the triggering condition when the current condition is triggered.

Sequential operation

“Snapshot intervalsecond(s)” Network Camera will send snapshots at the specified intervals

to the external server using the method selected below. Remember: This operation is still subject

to the conditions set in the weekly schedule.

Page 44 of the LevelOne LevelOne user manual — Method for sending snapshot
Page 44 · click to enlarge
Page 44

Method for sending snapshot

“Email” This selects the uploading method following the intervals set above. The snapshot

named “prefix-yyyymmdd-hhmmss.jpg” will be attached in the email.

“FTP” The snapshots will be uploaded to the external FTP server with the file name defined in the

next option. This can also be used to refresh the captured images stored in the external web

server to build creative homepages.

“FTP put snapshots with date and time suffix” This option sets up the snapshot capture date

and time, which can be used to easily differentiate the snapshot file names in the sequential

operation. For instance, “prefix-20030102-030405.jpg” means the JPEG image was captured in

the year 2003, January the 2nd, at 3 o’clock, 4 minute, and 5 second. If this suffix is omitted, the file

named “video.jpg” on the external FTP server will be refreshed at the specified interval.

LevelOne LevelOne — Method for sending snapshot diagram (page 44)
Fig. 27 · Method for sending snapshot
Page 45 of the LevelOne LevelOne user manual — System log
Page 45 · click to enlarge
Page 45

System log

The Network camera support log the system messages on remote server. The protocol is

compliant to RFC 3164. If you have external Linux server with syslogd service, use “-r” option to

turn on the facility for receiving log from remote machine. Or you can use some software on

Windows which is compliant to RFC 3164.

Check “Enable remote log” and input the “IP address” and “port” number of the log server to

enable the remote log facility.

In the “Current log”, it displays the current system log file. The content of the log provides useful

information about configuration and connection after system boot- up.

LevelOne LevelOne — System log diagram (page 45)
Fig. 28 · System log
Page 46 of the LevelOne LevelOne user manual — Viewing system parameters
Page 46 · click to enlarge
Page 46

Viewing system parameters

Click on this link on the configuration page to view the entire system’s parameter set. The content

is the same as those in CONFIG.INI.

LevelOne LevelOne — Viewing system parameters diagram (page 46)
Fig. 29 · Viewing system parameters
Page 47 of the LevelOne LevelOne user manual — Maintenance
Page 47 · click to enlarge
Page 47

Maintenance

Four actions can be selected

“reboot” click the reboot button to restart system

“factory default” Click on Factory default button on the configuration page to restore the factory

default settings. Any changes made so far will be lost and the system will be reset to the initial

factory settings. The system will restart and require the installer program to set up the network

again.

Recalibrate the home position to the default center to recover the tolerance cased by some

external forces. This function is the same as the “Center” button on the Remote Controller. Please

Camera will calibrate immediately.

“upgrade firmware” Select the firmware file and click upgrade button

LevelOne LevelOne — Maintenance diagram (page 47)
Fig. 30 · Maintenance

“Calibrate”

Page 48 of the LevelOne LevelOne user manual — RESTORE:
Page 48 · click to enlarge
Page 48

Appendix

A. Troubleshooting

Status LED

The following table lists the LED patterns in general.

Loading system after power on Steady red

During booting procedure Steady green, blue and red

Detecting and setting network Steady green and blue. Blink red till IP address is

After network is setup (system up) Blink green every second and steady red

During the upgrade firmware process Blink green every second and fast blink red

Enable audio Steady blue. Disable audio will turn off blue LED.

Reset and restore

There is a button in the back side of the Network Camera. It is used to reset the system or restore

the factory default settings.

RESET: Click on the button.

RESTORE:

1. Press on the button continuously.
2. Wait for all LED blink fast.
3. Free the button.

Restoring the factory defaults will erase any previous settings.

Condition LED color · confirmed

Page 49 of the LevelOne LevelOne user manual — Get server parameter values
Page 49 · click to enlarge
Page 49

B. URL commands of the Network Camera

For some customers who already have their own web site or web control application, the Network

Camera can be easily integrated through convenient URLs. This section lists the commands in

URL format corresponding to the basic functions of the Network Camera.

Get server parameter values

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/getparam.cgi?[<parameter>]

where the <parameter> should be <group>[_<name>] or <group>[.<name>] If you do not specify

the any parameters, all the parameters on the server will be returned. If you specify only <group>,

the parameters of related group will be returned.

When query parameter values, the current parameter value are returned.

Successful control requests returns parameter pairs as follows.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length<length>\r\n

where is

is the actual length of content.

Show 5 more labels / short text on this page
[&<parameter>…] · \r\n · <parameter pair> · <parameter>=<value>\r\n · [<parameter pair>]
Page 50 of the LevelOne LevelOne user manual — Set server parameter values
Page 50 · click to enlarge
Page 50
Examplerequest IP address and it’s response

Request:

http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress

Response:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length33\r\n

network.ipaddress=192.168.0.123\r\n

Set server parameter values

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/setparam.cgi? [nosync=<value>&]<parameter>=<value>

<group>_<name>. value to assigned Assign <value> to the parameter <group>_<name>..

return <return page> Redirect to the page <return page> after the parameter

is assigned. The <return page> can be a full URL path

or relative path according the the current path. If you

omit this parameter, it will redirect to an empty page.

(noteThe return page can be a general HTML

file(.htm, .html) or a server script executable (.vspx)

file. It can not be a CGI command. It can not have any

extra parameters. This parameter must be put at end of

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Show 4 more labels / short text on this page
\r\n · [&<parameter>=<value>…][&return=<return page>] · parameter value description · parameter list)
Page 51 of the LevelOne LevelOne user manual — NAME VALUE DESCRIPTION
Page 51 · click to enlarge
Page 51
Context-Length<length>\r\n

where is

Only the parameters that you set and readable will be returned.

ExampleSet the IP address of server to 192.168.0.123

Request:

http://myserver/cgi-bin/admin/setparam.cgi?Network_IPAddress=192.168.0.123

Response:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length33\r\n

network.ipaddress=192.168.0.123\r\n

Available parameters on the server

GroupSystem

NAME VALUE DESCRIPTION

host name of server

0 Do not turn off the led indicator ledoff

(r/w) 1 Turn off the led indicator

<yyyy/mm/dd> year, month and date separated by slash.

keep date unchanged

Using NTP to sync date/time automatically

<hh:mm:ss> hour, minute and second separated by

colon.

keep date unchanged

Show 13 more labels / short text on this page
\r\n · <parameter pair> · <parameter>=<value>\r\n · [<parameter pair>] · \r\n · hostname · (r/w) · characters> · <<Wireless>Network Camera > · date · (r/w) · time · (r/w)
Page 52 of the LevelOne LevelOne user manual — NAME VALUE DESCRIPTION
Page 52 · click to enlarge
Page 52

Using NTP to sync date/time automatically

<skip to invoke default server>

-12 ~ 12 time zone, 8 means GMT +8:00

0 ~ 2592000 0 to Disable automatic time adjustment,

otherwise, it means the seconds between

NTP automatic update interval.

12 characters mac address without hyphen

The version of firmware, including model,

company, and version number

0 Restore the system parameters to default

value.

Positive integer Restore the system parameters to default

value and restart the server after

seconds.

Restart the server after seconds.

-1 Not restart the server.

0 Using the profile of viewing by computer viewmode

(r/w) 1 Using the profile of viewing by mobile phone

GroupSecurity

NAME VALUE DESCRIPTION

change user name.

change user’s password.

The UserPass_0 is root’s password.

[conf] show user’s privilege. The privilege can be

- only permit to view live media

conf – Permit to change server’s configuration

1 ~ 21 The current account number on the server

including root.<1>

Show 34 more labels / short text on this page
ntp · NTP server · (r/w) · address> · timezone · (r/w) · <8> · updateinterval · (r/w) · <0> · serialnumber · (r) · connected · firmwareversion · (r) · characters> · restore · (w) · reset · 0 ~ 65535 · (w) · username_<1~20> · (r/w) · 16 characters> · <blank> · userpass_<0~20> · (r/w) · 14 characters> · <blank> · userattr_<1~20> · (r) · <blank> · usercount · (r)
Page 53 of the LevelOne LevelOne user manual — NAME VALUE DESCRIPTION
Page 53 · click to enlarge
Page 53
GroupNetwork

NAME VALUE DESCRIPTION

PPPoE account user name

1 enable to get ipaddress, subnet, router, dns1,

dns2 from DHCP server at next reboot

0 Using preset ipaddress, subnet, router, dns1,

IP address of server

<192.168.0.99>

subnet mask

<255.255.255.0>

default gateway

primary DNS server

secondary DNS server

address, string shorter than

User name of primary smtp server

Password of primary smtp server

address, string shorter than

mailuser2

Show 55 more labels / short text on this page
0 LAN type · (r/w) 1 PPPoE · pppoeuser · (r/w) · characters> · <blank> · pppoepass · PPPoE account password · (r/w) · characters> · <blank> · resetip · (r/w)(restart) · dns2 · ipaddress · (r/w) (restart) · subnet · (r/w) (restart) · router · (r/w) (restart) · <blank> · dns1 · (r/w) (restart) · <blank> · dns2 · (r/w) (restart) · <blank> · smtp1 · primary SMTP server · (r/w) · <blank> · 40 characters> · mailto1 · mail recipient address · (r/w) · characters> · <blank> · mailuser1 · (r/w) · characters> · <blank> · mailpass1 · (r/w) · characters> · <blank> · smtp2 · secondary SMTP server · (r/w) · <blank> · 40 characters> · mailto2 · mail recipient address · (r/w) · characters> · <blank>
Page 54 of the LevelOne LevelOne user manual — Available parameters on the server
Page 54 · click to enlarge
Page 54

Password of secondary smtp server

address, string shorter than

user name for primary FTP server

password for primary FTP server

upload folder in primary FTP server

1 Enable passive mode of primary FTP server ftppasvmode1

(r/w) 0 Disable passive mode of primary FTP server

address, string shorter than

user name for secondary FTP server

password for secondary FTP server

upload folder in secondary FTP server

1 Enable passive mode of primary FTP server ftppasvmode2

(r/w) 0 Disable passive mode of primary FTP server

videoport

Show 68 more labels / short text on this page
(r/w) characters> <blank> · mailpass2 · (r/w) · characters> · <blank> · returnemail · return email address · (r/w) · characters> · <blank> · localftpport · FTP port · (r/w) · 65535> · <21> · ftp1 · primary FTP server · (r/w) · <blank> · 40 characters > · ftpport1 · primary FTP port · (r/w) · 65535> · <21> · ftpuser1 · (r/w) · characters> · <blank> · ftppass1 · (r/w) · characters> · <blank> · ftpfolder1 · (r/w) · characters> · <blank> · ftp2 · secondary FTP server · (r/w) · 40 characters > · ftpport2 · secondary FTP port · (r/w) · 65535> · <21> · ftpuser2 · (r/w) · characters> · <blank> · ftppass2 · (r/w) · characters> · <blank> · ftpfolder2 · (r/w) · characters> · <blank> · httpport · HTTP port · (r/w) (restart) · 65535> · <80> · rtspport · RTSP port · (r/w) (restart) · 65535> · <554>
Page 55 of the LevelOne LevelOne user manual — "NONE", "1M", "2M", "5.5M",
Page 55 · click to enlarge
Page 55

audio Channel port for RTP

<live.sdp>

GroupWireless (restart)

SSID for wireless lan settings

0 Infrastructure mode wlmode

(r/w) 1 Adhoc mode

"NONE", "1M", "2M", "5.5M",

Transmit rate in Mbps

"11M", "22M"

for 802.11b+

"NONE", "1M", "2M", "5.5M",

"11M", "6M", "9M", "12M",

"18M", "24M", "36M", "48M",

"54M", "Auto" for 802.11g

0 None data encryption

1 WEP data encryption

2 WPA-PSK data encryption

Open Open mode authmode

(r/w) Shared Shared mode

(64, 128) for 802.11g Key length in bits

HEX Key1 ~ Key4 will be represented in HEX format keyformat

(r/w) ASCII Key1 ~ Key4 will be represented in ASCII format

1 ~ 4 Default key number

WEP key1 for encryption

WEP key2 for encryption

WEP key3 for encryption

Show 39 more labels / short text on this page
(r) 65535> <5558> · audioport · (r) · 65535> · <5556> · accessname · RTSP access name · (r/w) · characters> · ssid · (r/w) · characters> · <default> · txrate · (r/w) · <Auto> · encrypt · (r/w) · keylength · (r/w) · <64> · keyselect · (r/w) · <1> · key1 · (r/w) · characters> (depends on · <0000000000> · keyformat & keylength) · key2 · (r/w) · characters> (depends on · <0000000000> · keyformat & keylength) · key3 · (r/w) · characters> (depends on · <0000000000> · keyformat & keylength)
Page 56 of the LevelOne LevelOne user manual — Available parameters on the server
Page 56 · click to enlarge
Page 56
LevelOne LevelOne — Available parameters on the server diagram (page 56)
Fig. 31 · Available parameters on the server
GroupIPFilter
LevelOne LevelOne — Available parameters on the server diagram (page 56)
Fig. 32 · Available parameters on the server

1.0.0.0 ~ 255.255.255.255 Allowed starting RTSP connection IP address

1.0.0.0 ~ 255.255.255.255 Allowed ending RTSP connection IP address

1.0.0.0 ~ 255.255.255.255 Denied starting RTSP connection IP address

1.0.0.0 ~ 255.255.255.255 Denied ending RTSP connection IP address

GroupVideo
LevelOne LevelOne — Available parameters on the server diagram (page 56)
Fig. 33 · Available parameters on the server

1, 3, 5, 10, 30, 60, 90, 120 Key frame interval

Page 57 of the LevelOne LevelOne user manual — Available parameters on the server
Page 57 · click to enlarge
Page 57
LevelOne LevelOne — Available parameters on the server diagram (page 57)
Fig. 34 · Available parameters on the server

30 (for 60Hz only) set maximum frame rate to 30 fps

Page 58 of the LevelOne LevelOne user manual — Available parameters on the server
Page 58 · click to enlarge
Page 58
LevelOne LevelOne — Available parameters on the server diagram (page 58)
Fig. 35 · Available parameters on the server

(r/w) 0 Do not overlay time stamp on video

GroupAudio
LevelOne LevelOne — Available parameters on the server diagram (page 58)
Fig. 36 · Available parameters on the server
GroupImage
LevelOne LevelOne — Available parameters on the server diagram (page 58)
Fig. 37 · Available parameters on the server

Adjust brightness of image according to mode

Adjust saturation of image according to mode

Adjust contrast of image according to mode

Adjust hue of image according to mode

Page 59 of the LevelOne LevelOne user manual — NAME VALUE DESCRIPTION
Page 59 · click to enlarge
Page 59
GroupCAMCTRL

NAME VALUE DESCRIPTION

-5 ~ 5 Pan speed

-5 ~ 5 Tilt speed

-5 ~ 5 Zoom speed

-5 ~ 5 Auto pan speed

0 ~ 9999 Time to dwelling when patrol

Text string shorter than 40

The name of preset location

characters.

-1024 ~ 1024 The pan coordinate of preset location.

-56 ~ 144 The tilt coordinate of preset location.

Text string shorter than 40

The name of patrol location

characters.

GroupMotion

NAME VALUE DESCRIPTION

0 disable motion detection enabled

(r/w) 1 enable motion detection

0 disable motion window #1 winenabled_

(r/w) 1 enable motion window #1

name of motion window #1

0 ~ 320 Left coordinate of window position.

0 ~ 240 Top coordinate of window position.

0 ~ 320 Width of motion detection window.

0 ~ 240 Height of motion detection window.

Show 34 more labels / short text on this page
panspeed · (r/w) · tiltspeed · (r/w) · zoomspeed · (r/w) · autospeed · (r/w) · dwelling · (r/w) · presetname_<0~9> · (r/w) · presetpan_<0~9> · (r/w) · presettilt_<0~9> · (r/w) · patrolname_<0~19> · (r/w) · winname_<0~2> · (r/w) · characters > · <blank> · winleft_<0~2> · (r/w) · <0> · wintop_<0~2> · (r/w) · <0> · winwidth_<0~2> · (r/w) · <0> · winheight_<0~2> · (r/w) · <0>
Page 60 of the LevelOne LevelOne user manual — NAME VALUE DESCRIPTION
Page 60 · click to enlarge
Page 60

0 ~ 100 Percent of motion detection window

0 ~ 100 Sensitivity of motion detection window

1 Update the above motion detection settings

GroupDDNS

NAME VALUE DESCRIPTION

0, 1 Enable or disable the dynamic dns.

1 ~ 6 dyndns.org (dynamic)

dyndns.org (custom)

tzo.com

dhs.org

safe100.net

dyn-interfree.it

Text string shorter than 127

Your dynamic hostname.

characters.

Text string shorter than 63

Your user or email to login ddns service

characters.

Text string shorter than 20

Your password or key to login ddns service

characters.

0, 1 Update the above ddns settings to take effect

GroupUPNP

NAME VALUE DESCRIPTION

0, 1 Enable or disable the UPNP presentation

service.

GroupUPNPfor

NAME VALUE DESCRIPTION

Show 31 more labels / short text on this page
winobjsize_<0~2> · (r/w) · <0> · winsensitivity_<0~2> · (r/w) · <0> · update · (w) · to take effect · enable · (r/w) · <0> · provider · (r/w) · <1> · hostname · (r/w) · <blank> · usernameemail · (r/w) · provider · <blank> · passwordkey · (r/w) · provider · <blank> · update · (w) · enable · (r/w) · <1>
Page 61 of the LevelOne LevelOne user manual — Camera Control
Page 61 · click to enlarge
Page 61

0, 1 Enable or disable the UPNP port forwarding

service.

GroupApp

NAME VALUE DESCRIPTION

File name of script

<script.vssx>

0 Disable script enablescript

(r/w) 1 Enable script

GroupSyslog

NAME VALUE DESCRIPTION

0 disable remote log enableremotelog

(r/w) 1 enable remote log

<IP address> Log server IP address

<514> Server port used for log

Camera Control

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/camctrl.cgi? [move=][&focus=]

[&speedapp=<value>][&auto=][&zoom=][&return=<return page>]

home Move to camera to home position

up Move camera up

down Move camera down

left Move camera left

Show 13 more labels / short text on this page
enable · (r/w) · <0> · scriptname · (r) · characters> · serverip · (r/w) · serverport · (r/w) · [&iris=<value>][&speedpan=<value>][&speedtilt=<value>][&speedzoom=<value>] · parameter value description · move
Page 62 of the LevelOne LevelOne user manual — Application page CGI command
Page 62 · click to enlarge
Page 62

right Move camera right

speedpan -5 ~ 5 Set the pan speed

speedtilt -5 ~ 5 Set the tilt speed

speedapp -5 ~ 5 Set the auto pan/patrol speed

return Redirect to the page <return page> after the parameter is

assigned. The <return page> can be a full URL path or

relative path according to the current path. If you omit this

parameter, it will redirect to an empty page.

Recall

MethodGET

Syntax:

http://<servername>/cgi-bin/recall.cgi?

recall=[&return=<return page>]

recall Text string less than

One of the present positions to recall.

return <return page> Redirect to the page <return page> after the parameter is

assigned. The <return page> can be a full URL path or

relative path according to the current path. If you omit this

parameter, it will redirect to an empty page.

Application page CGI command

MethodGET/POST
Show 6 more labels / short text on this page
auto · pan Auto pan · patrol Auto patrol · stop Stop camera · parameter value description · 30 characters
Page 63 of the LevelOne LevelOne user manual — Available parameters on the server
Page 63 · click to enlarge
Page 63

Syntax:

http://<servername>/cgi-bin/admin/gen-eventd-conf.cgi?[ snapshot_enable=]

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length<length> \r\n

If(method == get || method == set)

Else if(method == normal)

0 Enable snapshot application snapshot_enable

1 Disable snapshot application

weekday 0,1,2,3,4,5,6 The array indicate weekly schedule

always 24 hours full day time_method

interval Select begin time and end time

begin_time hh:mm Begin time of weekly schedule

Show 16 more labels / short text on this page
[&weekday=<value>][&time_method=<value>][&begin_time=<value>] · [&end_time=<value>] · [&ss_prefix=<value>][&trigger_type=<value>] · [&md_prenum=<value>][&md_postnum=<value>][&md_delay=<value>] · [&sq_interval=<value>] · [&send_method=<value][&ftp_suffix=<value>] · \r\n · { · tue=<value>\r\n · wed=<value>\r\n · … · } · { · Application page contents · } · parameter Value description
Page 64 of the LevelOne LevelOne user manual — Capture single snapshot
Page 64 · click to enlarge
Page 64

end_time hh:mm End time of weekly schedule

ss_prefix <text string shorter

Snapshot file name prefix for both event and

motion Set trigger by motion detect trigger_type

md_win 0,1,2 The array indicate which motion windows are used

md_prenum 1~5 The numbers of snapshot before event

md_postnum 1~5 The numbers of snapshot after event

md_delay 1~999 The delay seconds for detecting next motion event

sq_interval 1~999 The interval seconds of sequential snapshot

mail Send snapshot by mail send_method

ftp Send snapshot by ftp

ftp_suffix 0/1 Enable/Disable file name prefix

Capture single snapshot

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/video.jpg

Server will return the most up-to-date snapshot in JPEG format. The size and quality of image will

be set according to the video settings on the server.

Return:

HTTP/1.0 200 OK\r\n

Content-Typeimage/jpeg\r\n
[Content-Length<image size> \r\n]

<binary JPEG image data>

than 60 characters> · sequential operation · sequential Snapshot sequentially

Page 65 of the LevelOne LevelOne user manual — Account management
Page 65 · click to enlarge
Page 65

Account management

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/editaccount.cgi?

method=&username=<name>[&userpass=<value>][&privilege=<value>]

[&privilege=][…][&return=<return page>]

add Add an account to server. When using this method,

“username” field is necessary. It will use default value of

other fields if not specified.

delete Remove an account from server. When using this

method, “username” field is necessary, and others are

ignored.

edit Modify the account password and privilege. When using

this method, “username” field is necessary, and other

fields are optional. If not specified, it will keep original

settings.

username The name of user to add, delete or edit

userpass The password of new user to add or that of old user to

modify. The default value is an empty string.

The privilege of user to add or to modify. The privilege

can be the addition of the following values. Ex: A user

with configure access can be assigned privilege as

privilege=conf.

return Redirect to the page <return page> after the parameter

is assigned. The <return page> can be a full URL path

or relative path according the the current path. If you

omit this parameter, it will redirect to an empty page.

Show 4 more labels / short text on this page
parameter value Description · method · privilege · conf configuration privilege
Page 66 of the LevelOne LevelOne user manual — Configuration file
Page 66 · click to enlarge
Page 66

System logs

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/syslog.cgi

Server will return the up-to-date system log.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length<syslog length>\r\n

Configuration file

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/configfile.cgi

Server will return the up-to-date configuration file.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length<configuration file length>\r\n
Show 4 more labels / short text on this page
\r\n · <system log information>\r\n · \r\n · <configuration data>\r\n
Page 67 of the LevelOne LevelOne user manual — Upgrade firmware
Page 67 · click to enlarge
Page 67

Upgrade firmware

MethodPOST

Syntax:

http://<servername>/cgi-bin/admin/upgrade.cgi

Post data:

Server will accept the upload file named to be upgraded the firmware and return with

if indicated.

fimage=[&return=]\r\n · \r\n

Page 68 of the LevelOne LevelOne user manual — D. Technical specifications
Page 68 · click to enlarge
Page 68

D. Technical specifications

- System CPUVVTK-1000 RAM: 32MB SDRAM ROM: 4MB FLASH ROM

- Networking Protocol TCP/IP, HTTP, SMTP, FTP, DDNS, UPnP, Telnet, NTP, DNS, DHCP and RTSP Physical 10 baseT or 100 baseT Fast Ethernet auto negotiation WLAN (WCS-2060 Only) 802.11g wireless LAN - Video Algorithm supported MPEG4(simple profile) for streaming video JPEG for still image - Features Adjustable image size, quality and bit rate Time stamp and text overlay 3 motion detection windows - Resolution Up to 30/25 frames at 160x120 Up to 30/25 frames at 320x240 Up to 30/25 frames at 640x480 - Camera Specification 1/4 inch color CMOS sensor Resolution: 640x480 1.5Lux/F2.0 AGC, AWB, AES Electronic shutter: 1/60 ~ 1/15000 second - Lens Fixed focal with fine tuning, 4.0mm, F2.0 - Audio AAC, GSM-AMR

Page 69 of the LevelOne LevelOne user manual — Available parameters on the server
Page 69 · click to enlarge
Page 69

- Microphone Omni-directional Frequency: 50 – 16000Hz S/N ratio: more than 60dB - LED indicator Three color LEDs - Dimension 100mm(D) * 110mm(W) * 120mm(H) - Weight NET. 271g - Power Input: 100-240VAC, 50/60Hz, 0.5A Output: 12VDC, 1.5A Consumption: Max 7 W - Operating Environment Temperature: 0-50°C/32-122°F Humidity: 95%RH - EMI & Safety CE, FCC - Viewing system requirement Operating system Microsoft Windows 98SE/ME/2000/XP Browser Internet Explorer 5.x or above

Page 70 of the LevelOne LevelOne user manual — GNU GENERAL PUBLIC LICENSE
Page 70 · click to enlarge
Page 70

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc.

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not

allowed.

The licenses for most software are designed to take away your freedom to share and change it. By contrast,

the GNU General Public License is intended to guarantee your freedom to share and change free software--to

make sure the software is free for all its users. This General Public License applies to most of the Free

Software Foundation's software and to any other program whose authors commit to using it. (Some other

Free Software Foundation software is covered by the GNU Library General Public License instead.) You can

apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are

designed to make sure that you have the freedom to distribute copies of free software (and charge for this

service if you wish), that you receive source code or can get it if you want it, that you can change the soft-ware

or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you

to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of

the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the

recipients all the rights that you have. You must make sure that they, too, receive or can get the source code.

And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you

legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that there is

no warranty for this free software. If the software is modified by someone else and passed on, we want its

recipients to know that what they have is not the original, so that any problems introduced by others will not

reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that

redistributors of a free program will individually obtain patent licenses, in effect making the program

proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or

not licensed at all. The precise terms and conditions for copying, distribution and modification follow.

Preamble

Page 71 of the LevelOne LevelOne user manual — GNU GENERAL PUBLIC LICENSE
Page 71 · click to enlarge
Page 71

GNU GENERAL PUBLIC LICENSE

Terms And Conditions For Copying, Distribution And Modification

0. This License applies to any program or other work which contains a notice placed by the copyright holder

saying it may be distributed under the terms of this General Public License. The "Program", below, refers to

any such program or work, and a "work based on the Program" means either the Program or any derivative

work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or

with modifications and/or translated into another language. (Hereinafter, translation is included without

limitation in the term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License; they are outside its

scope. The act of running the Program is not restricted, and the output from the Program is covered only if its

contents constitute a work based on the Program (independent of having been made by running the Program).

Whether that is true depends on what the Program does.

1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any

medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright

any warranty; and give any other recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty

protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the

Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided

that you also meet all of these conditions:

a) You must cause the modified files to carry prominent notices stating that you changed the files and the date

of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from

the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of

this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when started

running for such interactive use in the most ordinary way, to print or display an announcement including an

appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty)

and that users may redistribute the program under these conditions, and telling the user how to view a copy of

this License. (Exceptionif the Program itself is interactive but does not normally print such an announcement,

your work based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived

from the Program, and can be reasonably considered independent and separate works in themselves, then

Page 72 of the LevelOne LevelOne user manual — Available parameters on the server
Page 72 · click to enlarge
Page 72

this License, and its terms, do not apply to those sections when you distribute them as separate works. But

when you distribute the same sections as part of a whole which is a work based on the Program, the

distribution of the whole must be on the terms of this License, whose permissions for other licensees extend

to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this

section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the

right to control the distribution of derivative or collective works based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a work

based on the Program) on a volume of a storage or distribution medium does not bring the other work under

the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or

executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must be distributed

under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more

than your cost of physically performing source distribution, a complete machine-readable copy of the

corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium

customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute corresponding source code.

(This alternative is allowed only for noncommercial distribution and only if you received the program in object

code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an

executable work, complete source code means all the source code for all modules it contains, plus any

associated interface definition files, plus the scripts used to control compilation and installation of the

executable. However, as a special exception, the source code distributed need not include anything that is

normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on)

of the operating system on which the executable runs, unless that component itself accompanies the

executable.

If distribution of executable or object code is made by offering access to copy from a designated place, then

offering equivalent access to copy the source code from the same place counts as distribution of the source

code, even though third parties are not compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this

License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will

automatically terminate your rights under this License. However, parties who have received copies, or rights,

from you under this License will not have their licenses terminated so long as such parties remain in full

compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else grants you

permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if

Page 73 of the LevelOne LevelOne user manual — Available parameters on the server
Page 73 · click to enlarge
Page 73

you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the

Program), you indicate your acceptance of this License to do so, and all its terms and condi-tions for copying,

distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically

receives a license from the original licensor to copy, distribute or modify the Program subject to these terms

and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted

herein. You are not responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not

limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that

contradict the conditions of this License, they do not excuse you from the conditions of this License. If you

cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent

obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license

would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly

through you, then the only way you could satisfy both it and this License would be to refrain entirely from

distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of

the section is intended to apply and the section as a whole is intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or to

contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free

software distribution system, which is implemented by public license practices. Many people have made

generous contributions to the wide range of software distributed through that system in reliance on consis-tent

application of that system; it is up to the author/donor to decide if he or she is willing to distribute software

through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this

License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by

copyrighted interfaces, the original copyright holder who places the Program under this License may add an

explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or

among countries not thus excluded. In such case, this License incorporates the limitation as if written in the

body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public License

from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to

address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this

License which applies to it and "any later version", you have the option of following the terms and condi-tions

either of that version or of any later version published by the Free Software Foundation. If the Program does

Page 74 of the LevelOne LevelOne user manual — Available parameters on the server
Page 74 · click to enlarge
Page 74

not specify a version number of this License, you may choose any version ever published by the Free

Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are

different, write to the author to ask for permission. For software which is copyrighted by the Free Software

Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will

be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting

the sharing and reuse of software generally.

Page 75 of the LevelOne LevelOne user manual — ASSUME THE COST OF ALL NECESSARY SERVICING,
Page 75 · click to enlarge
Page 75

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE

PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES

PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU

ASSUME THE COST OF ALL NECESSARY SERVICING,

REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY

COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE

PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO

USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED

INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE

PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

All the source code of LevelOne GPL products are uploaded to http://www.level1.com

All the users can download freely.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the LevelOne LevelOne

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne LevelOne

Be the first to ask — other owners or our team will answer.

Original document

LevelOne LevelOne manual PDF

75 pages·2.8 MB·Security Camera·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…