EN
LevelOne logo
Official user manual

LevelOne FCS-5030

114 pages·3.8 MB·Security Camera·PDF·ENDEFRITNLJA
LevelOne FCS-5030
Table of Contents 80 sections LevelOne · FCS-5030 · IP Network Camera w/ Infrared LEDs · User Manual · … ShowHide
LevelOnep.1FCS-5030p.1IP Network Camera w/ Infrared LEDsp.1User Manualp.1Package Contentp.51. FCS-5030p.5Installationp.6Hardware installationp.6To install in Ethernetp.6Make connectionsp.7Software installationp.8How to Use Installation Wizardp.9Using Installation Wizardp.12User Interfacep.12Action buttonsp.14Function buttonsp.15Manual Setupp.16System Settingp.17Change Host Namep.17Change root passwordp.17Adjust date and timep.18Network Settingp.19PPPoE Settingp.19LAN Settingp.21Mobile Accessp.22Apply to selected devicep.23Upgradep.24Device Informationp.25Firmware Informationp.26Select Firmwarep.26Start Upgradep.27Initial Access to the Network Camerap.29Check Network Settingsp.29Add Password to prevent Unauthorized Accessp.29How to Usep.29Authenticationp.30Installing plug-inp.31Primary user’s capabilityp.32Main Screen with Camera Viewp.32Digital Zoomp.34MP4 Recordingp.35Snapshotp.35Local Settingsp.36Digital outputp.38Administrator’s capabilityp.39Fine-tuning for Best Performancep.39For Viewing by Mobile Phonep.39For Best Real-time Video Imagesp.39Only Quality Images Will Dop.40Somewhere Between Real-time and Clear Imagesp.40Opening accounts for new usep.41Protect Network Camera by passwordsp.41Build a security applicationp.42Software revision upgradep.43Definitions in Configurationp.44Basic-Networkp.44Network typep.44Audio and Videop.46Video Settingsp.46Audio settingsp.47Image Settingsp.48Privacy Maskp.50Systemp.52User Managementp.53Advanced-Networkp.54DDNSp.55HTTPp.55Two way audiop.56FTPp.56RTSP Streamingp.56IP Filteringp.58Motion detectionp.59Event Setupp.60Eventp.61Serverp.62Media Settingp.64Recordingp.66Peripheralsp.68System logp.69Maintenancep.70
Page 1 of the LevelOne FCS-5030 user manual — LevelOne
Page 1 · click to enlarge
Page 1
LevelOne FCS-5030 — LevelOne diagram (page 1)
Fig. 1 · LevelOne

LevelOne

FCS-5030

IP Network Camera w/ Infrared LEDs

User Manual

Ver 1.2.0 – 0904

Page 2 of the LevelOne FCS-5030 user manual — LevelOne
Page 2 · click to enlarge
Page 2

Before You Use This Product

The use of surveillance devices may be prohibited by law in your country. The Network Camera

is not only a high-performance web-ready camera but also can be part of a flexible surveillance

system. It is the user’s responsibility to ensure that the operation of such devices is legal before

installing this unit for its intended use.

It is important to first verify that all contents received are complete according to the list in the

"Package Contents" chapter. Take notice of the warnings before the Network Camera is

installed, then carefully read and follow the instructions in the “Installation” chapter to avoid

damages due to faulty assembly and installation. This also ensures the product is used

properly as intended.

The Network Camera is a network device and its use should be straightforward for those who

have basic network knowledge. The “Troubleshooting” chapter in the Appendix provides

remedies to the most common errors in set up and configuration. You should consult this

chapter first if you run into a system error.

The Network Camera is designed for various applications including video sharing, general

security/surveillance, etc. The “How to Use” chapter suggests ways to best utilize the Network

Camera and ensure proper operations. For the creative and professional developers, the "URL

Commands of The Network Camera" chapter serves to be a helpful reference to customize

existing homepages or integrating with the current web server.

For paragraphs preceded by

the reader should use caution to understand

completely the warnings. Ignoring the warnings may result in serious hazards or

injuries.

Page 3 of the LevelOne FCS-5030 user manual — LevelOne
Page 3 · click to enlarge
Page 3
Page 3 of the LevelOne FCS-5030 user manual — LevelOne
Page 4 of the LevelOne FCS-5030 user manual — LevelOne
Page 4 · click to enlarge
Page 4
Page 4 of the LevelOne FCS-5030 user manual — LevelOne
Page 5 of the LevelOne FCS-5030 user manual — 1. FCS-5030
Page 5 · click to enlarge
Page 5

Package Content

1. FCS-5030

2. Power Adapter
3. Camera Stand
4. CD Manual/Utility
5. Quick Installation Guide
Page 6 of the LevelOne FCS-5030 user manual — To install in Ethernet
Page 6 · click to enlarge
Page 6

Installation

In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator"

refers to the person who can configure the Network Camera and grant user access to the camera.

Hardware installation

LevelOne FCS-5030 — Hardware installation diagram (page 6)
Fig. 2 · Hardware installation

Please verify that your product package contains all the

accessories listed in the foregoing Package Contents.

Depending on the user’s application, an Ethernet cable may be

needed. The Ethernet cable should meet the specs of UTP

Category 5 and not exceed 100 meters in length.

To install in Ethernet

Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet cable plug

in the power adapter. If the LED turns out to blink orange-color, go to next paragraph “Software

installation”.

This Network Camera provides a general I/O terminal block with one digital input and one digital

output device control. The pin definition is as below.

Consult with the dealer of the peripherals for correct installation.

1 SW_NOPEN OUTPUT (Max. 400mA, 12VDC ±5%)

LevelOne FCS-5030 — To install in Ethernet diagram (page 6)
Fig. 3 · To install in Ethernet

2 SW_COMMON OUTPUT (open from SW_OPEN at

initial state) (close with SW_OPEN when set DO to ON)

3 DI+ INPUT (Max. 50mA, 12VDC)

4 DI- INPUT (Initial state of DI is low)

Page 7 of the LevelOne FCS-5030 user manual — Make connections
Page 7 · click to enlarge
Page 7

Make connections

LevelOne FCS-5030 — Make connections diagram (page 7)
Fig. 4 · Make connections

To completely avoid the camera from water sock, apply waterproof process if necessary.

Utilize silicone clay or similar waterproof material applied to the screws, screw holes and other

necessary portions.

Tape the junction points of the connecters on the cable.

LevelOne FCS-5030 — Make connections diagram (page 7)
Fig. 5 · Make connections

Reset Button · Waterproof Process

Page 8 of the LevelOne FCS-5030 user manual — Software installation
Page 8 · click to enlarge
Page 8

Software installation

At the end of the hardware installation, users can use Installation Wizard program included in the

product CDROM to find the location of the Network Camera. There may be many Network

Cameras in the local network. Users can differentiate the Network Cameras with the MAC

address . The MAC address is printed on the label which is on the bottom of the Network

Camera body. Please refer to the Quick installation guide of Installation Wizard for details.

Once installation is complete, the Administrator should proceed to the next section "Initial

Access to the Network Camera" for necessary checks and configurations.

Page 9 of the LevelOne FCS-5030 user manual — How to Use Installation Wizard
Page 9 · click to enlarge
Page 9

How to Use Installation Wizard

Installation

The following are steps for the software installation.

1. Put the Installation disk into the CD-ROM drive, and the installation should start

automatically. If the installation does not start, click on “Start” on the lower left corner of your

screen, open “My Computer” and double click on the CD-ROM->Installation_Wizard.exe. The

Installation Wizard Installation Window will appear.

LevelOne FCS-5030 — How to Use Installation Wizard diagram (page 9)
Fig. 6 · How to Use Installation Wizard

Installation Wizard Installation Window

2. Please read the license agreement first, and then click on “I Agree” to continue the

installation process. The install process will go on and then the below window will appear. This

page is for you to select the additional component you want to install. The component “Create

shortcut on desktop” will create a shortcut on the desktop. It is more convenient for you to launch

Install Wizard 2. After selecting the components, please click on the “Next” Button to continue.

LevelOne FCS-5030 — How to Use Installation Wizard diagram (page 9)
Fig. 7 · How to Use Installation Wizard

Select components to install for the Installation Wizard

Page 10 of the LevelOne FCS-5030 user manual — How to Use Installation Wizard
Page 10 · click to enlarge
Page 10
3. Select the installation directory for this application software and click on “Install” button.

You can also change the installation directory by clicking on “Browse…” button. After the proper

directory chose, please click on the “Install” button to continue.

LevelOne FCS-5030 — How to Use Installation Wizard diagram (page 10)
Fig. 8 · How to Use Installation Wizard

Destination Location for Installation

4. After clicking “Install” button, the install system will install the Installation Wizard to your

computer, and a progress bar will display on the dialog. After completed the installation, please

click on the “Close” button.

LevelOne FCS-5030 — How to Use Installation Wizard diagram (page 10)
Fig. 9 · How to Use Installation Wizard

Completed

Page 11 of the LevelOne FCS-5030 user manual — How to Use Installation Wizard
Page 11 · click to enlarge
Page 11
Page 11 of the LevelOne FCS-5030 user manual — How to Use Installation Wizard
Page 12 of the LevelOne FCS-5030 user manual — Using Installation Wizard
Page 12 · click to enlarge
Page 12

Using Installation Wizard

User Interface

Once you run the Installation Wizard, after a short searching time, you will see the

user interface as below. “Manual Setup” button, a “Refresh Devices” button and

an arrow button on the left panel of your user interface. When you click on the arrow

button, you will see more advanced functional buttons: “Firmware Upgrade”,

“Restore Default” and “About IW”. You can select your device by double-clicking

it in the device list. The left three buttons (“Manual Setup”, “Firmware Upgrade”,

and “Restore Default”) won’t be enabled until you select at least one device.

LevelOne FCS-5030 — Using Installation Wizard diagram (page 12)
Fig. 10 · Using Installation Wizard

User interface of Installation Wizard

Installation Wizard allows you to setup one device at one time and upgrade multiple devices (of the same model) at the same time. If you selected

different models, then the “Firmware Upgrade” button would be disabled.

Page 13 of the LevelOne FCS-5030 user manual — Using Installation Wizard
Page 13 · click to enlarge
Page 13

User interface of Installation Wizard after clicking on the arrow button

Page 14 of the LevelOne FCS-5030 user manual — Action buttons
Page 14 · click to enlarge
Page 14

Action buttons

Clicking on the “Refresh Devices” button will refresh the device list and search all

devices on the LAN again. Refreshing the device list will take several seconds.

If you want to link to your device, double-clicking it on your device list will lead you to

the browser for operating your device.

Refresh devices

Page 15 of the LevelOne FCS-5030 user manual — Function buttons
Page 15 · click to enlarge
Page 15

Function buttons

Click on this button to modify the setting of the selected devices. For more detail,

please refer to 0 Manual Setup.

Click on this button to upgrade the firmware of the selected devices. For more detail,

please refer to 0 Upgrade

Click on this button to restore the selected device to factory default.

Click on this button to get version information of the Installation Wizard .

Function buttons

Page 16 of the LevelOne FCS-5030 user manual — Manual Setup
Page 16 · click to enlarge
Page 16

Manual Setup

When you select one device in the selection list, the “Manual Setup” button

will be enabled. Click on it to modify the settings of the selected device. After clicked

on the “Manual Setup” button, Installation Wizard would try to connect to the

selected device.

The default Administrator’s password is blank and the Network Camera initially

will not ask for any password. If the authentication is failed, there would be a pop-up

dialog window to ask for correct password. If you failed three times, the Installation

Wizard would show you a warning dialog window and abort the connecting to the

selected device.

LevelOne FCS-5030 — Manual Setup diagram (page 16)
Fig. 11 · Manual Setup
LevelOne FCS-5030 — Manual Setup diagram (page 16)
Fig. 12 · Manual Setup

Authentication Dialog Window · Authentication error

Page 17 of the LevelOne FCS-5030 user manual — Change root password
Page 17 · click to enlarge
Page 17

System Setting

After connected to the selected device, the Installation Wizard will switch to system

setting page as below.

LevelOne FCS-5030 — System Setting diagram (page 17)
Fig. 13 · System Setting

Click on this button to cancel the setup progress.

Click on this button to keep the present setting and go to the next page.

Change Host Name

The “Hostname” is used for the homepage title of main page and is displayed as the

title in the video window of the main page. The maximum string length is 40

characters or 20 characters in double-byte-character-systems like Chinese or

Japanese. But for some models supported Unicode, the maximum string length

depends on the characters you input, and it may less than 20 characters.

Change root password

To change the administrator’s password, type the new password in both “Password”

and “Confirm Password” text boxes identically. What is typed will be displayed as

System setting page

Page 18 of the LevelOne FCS-5030 user manual — Adjust date and time
Page 18 · click to enlarge
Page 18

asterisks for security purposes. The maximum password depends on the server you

connected.

Adjust date and time

LevelOne FCS-5030 — Adjust date and time diagram (page 18)
Fig. 14 · Adjust date and time

There are three ways to adjust system date and time:

1. "Synchronize with computer time" : The easiest way is to make device

synchronized with your computer time.

2. “ Set date and time manually ”: Set the date and time manually by entering

new values. Notice the format in the related field while typing.

3. “ Synchronize to network time server automatically ”: Make device

automatically synchronize with timeservers over the Internet every hour.

If you want to keep the current date and time, please choose “Keep current date

and time”.

Date/Time setup

Page 19 of the LevelOne FCS-5030 user manual — PPPoE Setting
Page 19 · click to enlarge
Page 19

Network Setting

The Installation Wizard can help you to setup the network connection with LAN or

PPPoE. After you clicked on the “Next” button on the System page, the Installation

Wizard would lead you to the PPPoE setting page. If you want to connect your

server to Internet via PPPoE, please click on “Yes” to start the PPPoE setting

process, or click on “No” to invoke the LAN setting.

LevelOne FCS-5030 — Network Setting diagram (page 19)
Fig. 15 · Network Setting

Choosing the network type

PPPoE Setting

LevelOne FCS-5030 — PPPoE Setting diagram (page 19)
Fig. 16 · PPPoE Setting

Network setting for PPPoE

If you click on “Yes” in the “Network Type” dialog window, you will be led to the

PPPoE setting page. In this page, you can input the “PPPoE username” and

Page 20 of the LevelOne FCS-5030 user manual — Network Setting
Page 20 · click to enlarge
Page 20

“PPPoE password” provided by your ISP, and then the server will be set to PPPoE

mode rather than LAN mode when the setup is completed. If you don’t know the

account information, please contact your ISP. After inputting the account information,

please click on the “Next” button to continue your next step.

Page 21 of the LevelOne FCS-5030 user manual — LAN Setting
Page 21 · click to enlarge
Page 21

LAN Setting

If you click on “No” in the “Network Type” dialog window, you will be led to the

Network setting page. In this page, you can change the server’s IP address, subnet

mask, default gateway, primary DNS server, secondary DNS and DHCP server.

Please refer to the below page.

LevelOne FCS-5030 — LAN Setting diagram (page 21)
Fig. 17 · LAN Setting

Network Setting for LAN

You could set up the network with DHCP or fixed IP:

1. DHCP: Check the "Get IP by DHCP Server automatically" will force the device

to renew its IP address whenever it reboots, and the related network

configuration is provided by the DHCP server.

2. Fixed IP: If you want the device to use a fixed IP, please uncheck the "Get IP by

DHCP Server automatically" checkbox and assign a valid IP address, subnet

mask, default gateway and DNS server for the device.

Page 22 of the LevelOne FCS-5030 user manual — Mobile Access
Page 22 · click to enlarge
Page 22

Mobile Access

After finished the DDNS setting and click on the Next button. If your device supports

mobile viewer and you want to access the device by mobile phone, you can enable

the “Mobile Access” by clicking on the Yes button. The Installation Wizard will do

some setting for mobile viewing toward the device:

1. Video: The video codec will be set to MPEG-4, and the resolution will be set to

176x144 pixels.

2. Audio: The audio codec will be set to AAC.
LevelOne FCS-5030 — Mobile Access diagram (page 22)
Fig. 18 · Mobile Access

Mobile Access

Page 23 of the LevelOne FCS-5030 user manual — Apply to selected device
Page 23 · click to enlarge
Page 23

Apply to selected device

After configuring all the settings, the apply page will show up. Click on “Apply”

button to apply the changes to the selected device or click on “Back” button to go

back to the previous page and modify the setting again.

LevelOne FCS-5030 — Apply to selected device diagram (page 23)
Fig. 19 · Apply to selected device

When you click on the “Apply”, it will start to update your settings to server.

Apply page

Page 24 of the LevelOne FCS-5030 user manual — Upgrade
Page 24 · click to enlarge
Page 24

Upgrade

When you select one device or multiple devices (of the same model), the

“Firmware Upgrade” button will be enabled. Click on it to upgrade the firmware of

the selected device(s). After click on the “Firmware Upgrade” button, Installation

Wizard will try to connect the selected device(s) and lead you to the firmware

upgrade page.

Click on the “Firmware Upgrade”

Page 25 of the LevelOne FCS-5030 user manual — Device Information
Page 25 · click to enlarge
Page 25

Device Information

After connected to the selected device(s), it would display as below. If you select more than one

device, then the device information will show all the selected devices. You can switch to the server

info by click on the tab control.

LevelOne FCS-5030 — Device Information diagram (page 25)
Fig. 20 · Device Information
LevelOne FCS-5030 — Device Information diagram (page 25)
Fig. 21 · Device Information

Device information · Multiple devices information

Page 26 of the LevelOne FCS-5030 user manual — Select Firmware
Page 26 · click to enlarge
Page 26

Firmware Information

The selected firmware information will show the information about the file that you selected.

z Firmware version: The version number of the selected firmware.

Select Firmware

You can use the “Select firmware” button to browse the file that you want upgrade onto the

selected device(s). After selected the file, Installation Wizard will check whether the file you

selected is correct. If it’s the correct version, then the package information will display the

information about the file and enable the “Start Upgrade” button. Therefore you can click on the

button to upgrade the firmware. If not, then it will be a pop-up warning message.

LevelOne FCS-5030 — Select Firmware diagram (page 26)
Fig. 22 · Select Firmware

Select firmware

Page 27 of the LevelOne FCS-5030 user manual — Start Upgrade
Page 27 · click to enlarge
Page 27
LevelOne FCS-5030 — Start Upgrade diagram (page 27)
Fig. 23 · Start Upgrade
LevelOne FCS-5030 — Start Upgrade diagram (page 27)
Fig. 24 · Start Upgrade

Start Upgrade

Clicking on the “Start Upgrade” button to upgrade the firmware of the selected device(s), and it

will be a pop-up dialog window to show the progress of the upgrading process. Usually, it will take

about 5 to 10 minutes to finish the firmware upgrading. It depends on your server model and

network bandwidth. We recommend you do the upgrade process in wired LAN environment rather

than PPPoE or wireless environment.

Firmware Information

Page 28 of the LevelOne FCS-5030 user manual — Start Upgrade
Page 28 · click to enlarge
Page 28
LevelOne FCS-5030 — Start Upgrade diagram (page 28)
Fig. 25 · Start Upgrade

After the upgrade process had been done, you could see the dialog window as below. Please click

on the button “OK” to finish it.

LevelOne FCS-5030 — Start Upgrade diagram (page 28)
Fig. 26 · Start Upgrade

Update progress · Upgrade Done

Page 29 of the LevelOne FCS-5030 user manual — How to Use
Page 29 · click to enlarge
Page 29

Initial Access to the Network Camera

Check Network Settings

The Network Camera can be connected either before or immediately after software installation

onto the Local Area Network. The Administrator should complete the network settings on the

configuration page, including the correct subnet mask and IP address of gateway and DNS. Ask

your network administrator or Internet service provider for the detail information. By default the

Network Camera requires the Administrator to run installation every time it reboots. If the network

settings are to remain unchanged, disable the Install option. Refer to “Network settings” on the

System Configuration page for details. If any setting is entered incorrectly and cannot proceed to

setting up the Network Camera, restore the factory settings following the steps in the

“Troubleshooting” chapter of the Appendix.

Add Password to prevent Unauthorized Access

The default Administrator’s password is blank and the Network Camera initially will not ask for any

password. The Administrator should immediately implement a new password as a matter of

prudent security practice. Once the Administrator’s password is saved, the Network Camera will

ask for the user’s name and password before each access. The Administrator can set up a

maximum of twenty (20) user accounts. Each user can access the Network Camera except to

perform system configuration. Some critical functions are exclusive for the Administrator, such as

system configuration, user administration, and software upgrades. The user name for the

Administrator is permanently assigned as “root”. Once the password is changed, the browser will

display an authentication window to ask for the new password. Once the password is set, there

is no provision to recover the Administrator’s password. The only option is to restore to

the original factory default settings.

How to Use

A PC with Windows operating system can use the Internet Explorer to connect to the Network

Camera. A plug-in will be installed into the IE when it is connected for the first time. A PC with

Linux operating system can connect to the camera using a browser like Firefox. It needs to install

QuickTime first to view streaming.

Page 30 of the LevelOne FCS-5030 user manual — Authentication
Page 30 · click to enlarge
Page 30

Authentication

After opening the Web browser and typing in the URL of the Network Camera, a dialogue window

pops up to request a username and password. Upon successful authentication, the following

figure is displayed.

The foreground is the login window and the background shows the message if authentication fails.

The user may check the option box to save the password for future convenience. This option is

not available to the Administrator for obvious reason.

LevelOne FCS-5030 — Authentication diagram (page 30)
Fig. 27 · Authentication
Page 31 of the LevelOne FCS-5030 user manual — Installing plug-in
Page 31 · click to enlarge
Page 31

Installing plug-in

For the initial access to the Network Camera in Windows, the web browser may prompt for

permission to install a new plug-in for the Network Camera on the Internet Explorer. Permission

request depends on the Internet security settings of the user’s PC or notebook. If the highest

security level is set, the computer may prohibit any installation and execution attempt. This plug-in

has been registered for certificate and is used to display the video in the browser. Users may click

to proceed. If the web browser does not allow the user to continue to install, check

the Internet security option and lower the security levels or contact your IT or networking

supervisor for help.

LevelOne FCS-5030 — Installing plug-in diagram (page 31)
Fig. 28 · Installing plug-in

on

Page 32 of the LevelOne FCS-5030 user manual — Main Screen with Camera View
Page 32 · click to enlarge
Page 32

Primary user’s capability

Main Screen with Camera View

The main page layout has two parts:

Configuration functions: The camera can be configured using these user interfaces.

Camera View: What the camera sees.

Click on the configuration link to the left of the image window to enter the configuration page.

Here is the layout in IE when it is MPEG-4 streaming.

LevelOne FCS-5030 — Main Screen with Camera View diagram (page 32)
Fig. 29 · Main Screen with Camera View
Page 33 of the LevelOne FCS-5030 user manual — Primary user’s capability
Page 33 · click to enlarge
Page 33

The function in JPEG will be a little different when it is JPEG streaming. Only digital zoom and

record button are supported.

LevelOne FCS-5030 — Primary user’s capability diagram (page 33)
Fig. 30 · Primary user’s capability

Here is the layout in Firefox when it is MPEG-4 streaming. It uses QuickTime to streaming.

LevelOne FCS-5030 — Primary user’s capability diagram (page 33)
Fig. 31 · Primary user’s capability
Page 34 of the LevelOne FCS-5030 user manual — Digital Zoom
Page 34 · click to enlarge
Page 34

Here is the layout in Firefox when it is JPEG streaming.

Digital Zoom

Click on the magnifier icon under the camera view then the digital zoom control panel will be

shown. Uncheck “Disable digital zoom” and use the slider control to change the zoom factors.

LevelOne FCS-5030 — Digital Zoom diagram (page 34)
Fig. 32 · Digital Zoom
Page 35 of the LevelOne FCS-5030 user manual — Snapshot
Page 35 · click to enlarge
Page 35

MP4 Recording

Click on the red circle button

on the plugin to start MP4 recording. You can set the related

options in client setting page.

Snapshot

Click on “Snapshot”, web browser will pop up a new window to show the snapshot. Users can

point at the snapshot and click the right button of mouse to save it.

LevelOne FCS-5030 — Snapshot diagram (page 35)
Fig. 33 · Snapshot
LevelOne FCS-5030 — Snapshot diagram (page 35)
Fig. 34 · Snapshot
Page 36 of the LevelOne FCS-5030 user manual — Local Settings
Page 36 · click to enlarge
Page 36

Local Settings

LevelOne FCS-5030 — Local Settings diagram (page 36)
Fig. 35 · Local Settings

There are four settings for the client side in IE.

1. The first one is “ Stream Options ” for users to determine which stream to be streaming. This

product supports dual-stream. Therefore, there are two streams to choose.

2. The second one is “ MPEG-4 Media Options ” for users to determine which media to be

streaming under MPEG-4 mode.

3. The third one is “ MPEG-4 Protocol Options ” which allows choices on connection protocol

between client and server. There are four protocols choices to optimize your usage – UDP

unicast, UDP multicast, TCP and HTTP.

z The UDP unicast protocol allows for more real-time audio and video streams. However,

some packets may be lost due to network burst traffic and images may be obscured.

z The UDP multicast protocol allows to save the bandwidth of server while serving

multiple clients at the same time.

z The TCP protocol allows for less packet loss and produces a more accurate video

display. The downside with this protocol is that the real-time effect is worse than that

with the UDP protocol.

z The HTTP protocol allows the same quality as TCP protocol and the user don’t need to

open specific port to streaming under some network environment.

If no special need is required, UDP unicast protocol is recommended. Generally speaking,

the client’s choice will be in the order of UDP multicast → UDP unicast → TCP → HTTP. After

Page 37 of the LevelOne FCS-5030 user manual — Local Settings
Page 37 · click to enlarge
Page 37

the Network Camera is connected successfully, “Protocol Option” will indicate the selected

protocol. The selected protocol will be recorded in the user's PC and will be used for the next

connection. If the network environment is changed, or the user wants to let the web browser to

detect again, manually select the UDP protocol, save, and return HOME to re-connect.

4. The fourth one is “ MP4 Save Options ”. User can specify the recording folder, file name

prefix and suffix here.

There is only one setting “Stream Options” for the client setting side in Firefox. User can choose

to view stream1 and stream2.

http://<Network Camera>/clientset.html is the domain name or the original

IP address of the Network Camera.

Page 38 of the LevelOne FCS-5030 user manual — Digital output
Page 38 · click to enlarge
Page 38

Digital output

Click on “ON”, the digital output of the Network Camera will be triggered. Or, clicking on “OFF” can

let the digital output turn into normal state.

Page 39 of the LevelOne FCS-5030 user manual — For Best Real-time Video Images
Page 39 · click to enlarge
Page 39

Administrator’s capability

Fine-tuning for Best Performance

Best performance generally equates to the fastest image refresh rate with the best video quality,

and at the lowest network bandwidth as possible. The three factors, “Maximum frame rate”,

“Constant bit rate”, and “Fixed quality” for MPEG-4 mode and “Maximum frame rate” and “Fixed

quality” for JPEG mode on the Audio and Video Configuration page, are correlative to allow for

achieving the best performance possible.

LevelOne FCS-5030 — Fine-tuning for Best Performance diagram (page 39)
Fig. 36 · Fine-tuning for Best Performance

For Viewing by Mobile Phone

Most 3GPP cell phone supports media streaming with MPEG4 video and GSM-AMR audio. Due

to the limitation of the bandwidth for 3GPP, only 176x144 video solution will be supported for cell

phone viewing. Please set related video settings first as mentioned when viewing by mobile

phone.

For Best Real-time Video Images

To achieve good real-time visual effect, the network bandwidth should be large enough to allow a

transmission rate of greater than 20 image frames per second. If the broadband network is over 1

Mbps, set the “Constant bit rate” to 1000Kbps or 1200Kbps, or set “Fixed quality” at the highest

quality. The maximum frame rate is 30. If your network bandwidth is more than 512Kbps, you can

adjust the bit rate according to your bandwidth and set the maximum frame rate to 30 fps. If the

Page 40 of the LevelOne FCS-5030 user manual — Somewhere Between Real-time and Clear Images
Page 40 · click to enlarge
Page 40

images vary dramatically in your environment, you may want to slow the maximum frame rate

down to 20 fps in order to lower the rate of data transmission. This allows for better video quality

and the human eyes cannot readily detect the differences between those of 20, 25, or 30 frames

per second. If your network bandwidth is below 512 Kbps, set the “Constant bit rate” according to

your bandwidth and try to get the best performance by fine-tuning with the “Maximum frame rate”.

In a slow network, greater frame rate results in blur images. Video quality performance will vary

somewhat due to the number of users viewing on the network; even when the parameters have

initially been finely tuned. Performance will also suffer due to poor connectivity because of the

network’s burst constraint.

Only Quality Images Will Do

To have the best video quality, you should set “Fixed quality” at “Detailed” or “Excellent” and adjust

the “Maximum frame rate” to match your network’s bandwidth. If your network is slow and you

receive “broken” pictures, go to the TCP or HTTP protocol in “MPEG-4 Protocol Options” and

choose a more appropriate mode of transmission. The images may suffer a time delay due to a

slower connection. The delay will also increase with added number of users.

Somewhere Between Real-time and Clear Images

If you have a broadband network, set “Fixed quality” at “Good” or better, rather than setting

“Constant bit rate”. You can also fix the bandwidth according to your actual network speed and

adjust the frame rate. Start from 30 fps down for best results but not below 15 fps. If the image

qualities are not improved, select a lower bandwidth setting.

Page 41 of the LevelOne FCS-5030 user manual — Protect Network Camera by passwords
Page 41 · click to enlarge
Page 41

Opening accounts for new use

LevelOne FCS-5030 — Opening accounts for new use diagram (page 41)
Fig. 37 · Opening accounts for new use

Protect Network Camera by passwords

The Network Camera is shipped without any password by default. That means everyone can

access the Network Camera including the configuration as long as the IP address is known. It is

necessary to assign a password if the Network Camera is intended not to be accessed by others.

Type a new word twice in ○1 to enable protection. This password is used to identify the

administrator. Then add an account with user name, password and authentication for your friends

in ○2. You can edit or delete users from ○3.

Page 42 of the LevelOne FCS-5030 user manual — Build a security application
Page 42 · click to enlarge
Page 42

Build a security application

The Administrator can use the built-in motion detection to monitor any movement to perform many

useful security applications. To upload the snapshots, users can choose either email, FTP, HTTP

or Network storage according to user’s needs. All servers setting are in Server section on

Application page. Refer to the definition section for detail configuration.

1. Click on “ Configuration ” on homepage,
2. Click on “ Motion detection ” at the left column,
3. Check “Enable motion detection”,
4. Click on new to have a new window to monitor video,
5. Type in a name to identify the new window,
6. Use the mouse to click, hold, and drag the window corner to resize or the title bar to move
7. Fine-tune using the “Sensitivity” and “Percentage” fields to best suit the camera’s environment.

Higher “Sensitivity” detects the slighter motion. Higher “Percentage” discriminates smaller

8. Clicking on “Save” enables the activity display. Green means the motion in the window is

under the watermark set by Administrator and red means it is over the watermark,

9. Click on “ Application ” at the left column,
10. Add a server in server section,
11. Add a media with snapshot type in media section. And Set the number of pre-event and

post-event images to be uploaded

12. Add a event in event section

z Enter one event name and enable this event.

z Check the weekdays as you need and give the time interval to monitor the motion

z Select the Trigger on Motion detection and Check the window name set in step 5

z Set the appropriate delay time to avoid continuous false alarms following the original

z Check the server name set in Step 10 and select the media name set in Step 11.

13. Click on save to validate.

objects, · detection every day, · event

Page 43 of the LevelOne FCS-5030 user manual — Software revision upgrade
Page 43 · click to enlarge
Page 43

Software revision upgrade

Customers can obtain the up-to-date software from the web site of LevelOne. An easy-to-use

Upgrade Wizard is provided to upgrade the Network Camera with just a few clicks. The upgrade

function is opened to the Administrator only. To upgrade the system, follow the procedures below.

1. Download the firmware file named “xxx.pkg” from the appropriate product folder.
2. Run the Installation Wizard and proceed following the prompts. Refer to the instructions of the

Installation Wizard on CD-ROM for details.

3. Or upgrade firmware from HTTP web page directly.
4. The whole process will finish in a few minutes and it will automatically restart the system.

If power fails during the writing process of Flash memory, the program in the

memory of the Network Camera may be destroyed permanently. If the Network

Camera cannot restart properly, ask your dealer for technical service.

Page 44 of the LevelOne FCS-5030 user manual — Network type
Page 44 · click to enlarge
Page 44

Definitions in Configuration

Only the Administrator can access system configuration. Each category in the left column will be

explained in the following pages. The bold texts are the specific phrases on the Option pages. The

Administrator may type the URL below the figure to directly enter the frame page of configuration.

If the Administrator also wants to set certain options through the URL, read the reference

appendix for details.

Basic-Network

Any changes made on the Network type section will restart the system in order to validate the

changes. Make sure every field is entered correctly before clicking on

LevelOne FCS-5030 — Basic-Network diagram (page 44)
Fig. 38 · Basic-Network

Network type

The default type is LAN. Select PPPoE if using ADSL

"Get IP address automatically" & “Use fixed IP address”

The default status is “Get IP address automatically”. This can be tedious having to perform

software installation whenever the Network Camera starts. Therefore, once the network settings,

especially the IP address, have been entered correctly, select “Use fixed IP address” then the

“LAN” & “PPPoE”

Page 45 of the LevelOne FCS-5030 user manual — Definitions in Configuration
Page 45 · click to enlarge
Page 45

Network Camera will skip installation at the next boot. The Network Camera can automatically

restart and operate normally after a power outage. Users can run IP installer to check the IP

address assigned to the Network Camera if the IP address is forgotten or using the UPnP function

provided by the Network Camera (MS Windows XP provides UPnP function at My Network

Place). “IP address” This is necessary for network identification.

“Subnet mask” This is used to determine if the destination is in the same subnet. The default

value is “255.255.255.0”.

“Default router” This is the gateway used to forward frames to destinations in a different subnet.

Invalid router setting will fail the transmission to destinations in different subnet.

“Primary DNS” The primary domain name server that translates hostnames into IP addresses.

“Secondary DNS” Secondary domain name server that backups the Primary DNS.

“Primary WINS server” The primary WINS server that maintains the database of computer name

and IP address.

“Secondary WINS server” The secondary WINS server that maintains the database of computer

name and IP address.

“Enable UPnP presentation” Enable the UPnP camera short cut.

“Enable UPnP port forwarding” Enable UPnP port forwarding

“PPPoE” If using the PPPoE interface, fill the following settings from ISP

“User name” The login name of PPPoE account

“Password” The password of PPPoE account

“Confirm password” Input password again for confirmation

Page 46 of the LevelOne FCS-5030 user manual — Video Settings
Page 46 · click to enlarge
Page 46

Audio and Video

This product supports dual-stream. It provides two setting for video streams, but only one setting

for audio.

Video Settings

LevelOne FCS-5030 — Video Settings diagram (page 46)
Fig. 39 · Video Settings

“Video title” The text string can be displayed on video

“Color” Select either for color or monochrome video display.

z Flip: Vertically rotate the video.

z MirrorHorizontally rotate the video. Check options both if the Network Camera is installed

upside down.

“Modulation” Select the video input modulation types, NTSC, PAL, and Auto. After Change the

modulation type, please reboot the video server to make the change take effect.

“Video orientation”

Page 47 of the LevelOne FCS-5030 user manual — Audio settings
Page 47 · click to enlarge
Page 47

“Overlay title and time stamp on video and snapshot” Check it the title is shown on video and

snapshot.

“Enable cutting noise” Check it for PAL camera. The resolution will be compromised to 688*576

or 688*480 once this setting is checked.

There are different video quality settings for stream1 and stream2.

z Mode: It can be MPEG-4 or JPEG. If MPEG-4 is selected, it is streamed in RTSP protocol. If

JPEG is selected, it is streamed in server push mode.

z Frame sizeBoth MPEG-4 and JPEG have three options, including “QCIF (176x120 NTSC

and 176x144 PAL)”, “CIF (352x240 NTSC and 352x288 PAL)”, and “4CIF (704x480

NTSC and 704x576 PAL)”.

There are three dependent parameters provided in MPEG-4 mode for video performance

adjustment.

“Intra frame period” The interval of intra frame.

“Maximum frame rate” This limits the maximal refresh frame rate, which can be combined with

the “Video quality” to optimize bandwidth utilization and video quality. Choose “Constant bit

rate” If the user wants to fix the bandwidth utilization regardless of the video quality, choose

“Fixed quality” and select the desired bandwidth. The video quality may be poor due to the

sending of maximal frame rate within the limited bandwidth when images are moving rapidly.

Consequently, to ensure detailed video quality (quantization rate) regardless of the network, it will

utilize more bandwidth to send the maximal frames when images change drastically.

In JPEG mode, user can set “Maximum frame rate” and “Video quality” to adjust the video

performance.

Audio settings

“Mute” Turn off audio.

“Input gain” Modify the gain of the internal audio input.

“Audio type” Select audio codec “AAC” or “GSM-AMR” and the bit rate.

Page 48 of the LevelOne FCS-5030 user manual — Image Settings
Page 48 · click to enlarge
Page 48
LevelOne FCS-5030 — Image Settings diagram (page 48)
Fig. 40 · Image Settings

Image Settings

LevelOne FCS-5030 — Image Settings diagram (page 48)
Fig. 41 · Image Settings

Click on this button to pop up another window to tune “Brightness”,

Page 49 of the LevelOne FCS-5030 user manual — Image Settings
Page 49 · click to enlarge
Page 49

“Contrast”, “Hue” and “Saturation” for video compensation. Each field has eleven levels

ranging from -5 to +5. In “Brightness” and “Contrast” fields the value 0 indicates auto tuning.

The user may press

to fine-tune the image. When the image is O.K., press

set the image settings. Click on

to recall the original settings without incorporating the changes.

to

Page 50 of the LevelOne FCS-5030 user manual — Privacy Mask
Page 50 · click to enlarge
Page 50

Privacy Mask

LevelOne FCS-5030 — Privacy Mask diagram (page 50)
Fig. 42 · Privacy Mask

Click on the button to pop up another window to set privacy mask window. All users can not view

the block under privacy mask window.

“Enable privacy mask” Check this option to turn on privacy mask.

Click on this button to add a new window. At most five windows can exist simultaneously. Use the mouse to click, hold, and drag the window frame to resize or the title bar to move. Clicking

on the ‘x’ at the upper right-hand corner of the window deletes the window. Remember to click

save in order to validate the changes. The base of window axis is eight. You can see the X, Y,

width and height of the window.

Click on this button to save the related window settings.

"Window Name" The text will show at the top of the window.

The following figure shows the screen when

is clicked and the privacy mask is enabled.

Page 51 of the LevelOne FCS-5030 user manual — Privacy Mask
Page 51 · click to enlarge
Page 51
LevelOne FCS-5030 — Privacy Mask diagram (page 51)
Fig. 43 · Privacy Mask
Page 52 of the LevelOne FCS-5030 user manual — System
Page 52 · click to enlarge
Page 52

System

LevelOne FCS-5030 — System diagram (page 52)
Fig. 44 · System

"Host name" The text displays the title at the top of the main page.

"Time zone" Adjust the time with that of the time-servers for local settings.

"Keep current date and time" Click on this to reserve the current date and time of the Network

Camera. An internal real-time clock maintains the date and time even when the power of the

system is turned off.

"Sync with computer time" Synchronize the date and time of the Network Camera with the local

computer. The read-only date and time of the PC is displayed as updated.

“Manual” Adjust the date and time according to what is entered by the Administrator. Notice the

format in the related fields while doing the entry.

Network Camera starts up. It will fail if the assigned time-server cannot be reached.

“Automatic” “NTP server” Assign the IP address or domain name of the time-server. Leaving

the text box blank connects the Network Camera to the default time-servers.

“Update interval” Select hourly, daily, weekly, or monthly update with the time on the NTP server.

Page 53 of the LevelOne FCS-5030 user manual — User Management
Page 53 · click to enlarge
Page 53

User Management

“Root password” Change the Administrator’s password by typing in the new password

identically in both text boxes. The typed entries will be displayed as asterisks for security

purposes. After pressing

, the web browser will ask the Administrator for the new password

for access.

“Add user” Type the new user's name and password and press

to insert the new entry.

The new user will be displayed in the user name list. There is a maximum of twenty user accounts.

There are three kinds of authentication: Administrator, Operator and Viewer. Administrator can

fully control the camera operation. Operator’s access right can modify most of camera’s

parameters except some privilege and network options. Viewer can view, listen to camera; control

DIDO of camera. Network Camera can provide twenty accounts for your valuable customers or

friends.

“Manage user” Pull down the user list to find the user’s name and press

selected user. Or edit the password or authentication of the selected user and press

effect.

to delete the · to take

Page 54 of the LevelOne FCS-5030 user manual — Advanced-Network
Page 54 · click to enlarge
Page 54

Advanced-Network

LevelOne FCS-5030 — Advanced-Network diagram (page 54)
Fig. 45 · Advanced-Network
Page 55 of the LevelOne FCS-5030 user manual — HTTP
Page 55 · click to enlarge
Page 55
LevelOne FCS-5030 — DDNS diagram (page 55)
Fig. 46

DDNS

“Enable DDNS” This option turns on the DDNS function.

“Provider” The provider list contains seven hosts that provide DDNS services. Please connect to

the service provider’s website to make sure the service charges.

“Host Name” If the User wants to use DDNS service, this field must be filled. Please input the

hostname that is registered in the DDNS server.

“Username/E-mail” The Username or E-mail field is necessary for logging in the DDNS server or

notify the User of the new IP address. Note: when this field is input as “Username” the following

field must be input as “Password”.

“Password/Key” Please input the password or key to get the DDNS service.

“Save” Click on this button to save current settings for the DDNS service and UPnP function.

HTTP

“Authentication” It supports basic and digest modes.

“HTTP port” This can be other than the default Port 80. Once the port is changed, the users must

Page 56 of the LevelOne FCS-5030 user manual — RTSP Streaming
Page 56 · click to enlarge
Page 56

be notified the change for the connection to be successful. For instance, when the Administrator

changes the HTTP port of the Network Camera whose IP address is 192.168.0.100 from 80 to

8888, the users must type in the web browser “http://192.168.0.100:8888” instead of

“http://192.168.0.100”

“Secondary HTTP port” It support alternate port to access HTTP server.

“Access name for stream 1” This is the access URL of stream 1 for making connection from

client software when its codec type is JPEG.

“Access name for stream 2” This is the access URL of stream 2 for making connection from

client software when its codec type is JPEG.

Using http://<ip address>:/ to make connection.

Two way audio

“Two way audio port” This can be other than the default port 5060. The user can change this

value from 1025 to 65535. After the changed, the external Two-Way audio client program must

change the server port of connection accordingly.

FTP

“FTP port” This can be other than the default port 21. The user can change this value from 1025

to 65535. After the changed, the external FTP client program must change the server port of

connection accordingly.

RTSP Streaming

“Authentication” It supports disable, basic and digest modes.

“Access name for stream 1” This is the access URL of stream 1 for making connection from

client software when the codec type is MPEG-4.

“Access name for stream 2” This is the access URL of stream 2 for making connection from

client software when the codec type is MPEG-4.

Using rtsp:/// to make connection

“RTSP port” This can be other than the default Port 554

“RTP port for video” The video channel port for RTP. It must be an even number.

“RTCP port for video” The video channel port for RTCP. It must be the port number of video RTP

plus 1.

“RTP port for audio” The audio channel port for RTP. It must be an even number.

“RTCP port for audio” The audio channel port for RTCP. It must be the port number of audio

Page 57 of the LevelOne FCS-5030 user manual — Two way audio
Page 57 · click to enlarge
Page 57

RTP plus 1.

User can modify Multicast setting for stream1 and stream2.

“Always multicast” Select it to enable multicast always.

“Multicast group address” It is used by sources and the receivers to send and receive content.

“Multicast video port” The video channel port for multicast. It must be an even number.

“Multicast RTCP video port” The video channel port for multicast RTCP. It must be the port

number of multicast video port plus 1.

“Multicast audio port” The audio channel port for multicast. It must be an even number.

“Multicast RTCP audio port” The audio channel port for multicast RTCP. It must be the port

number of multicast audio port plus 1.

“Multicast TTL” It specifies the number of routers (hops) that multicast traffic is permitted to pass

through before expiring on the network.

Page 58 of the LevelOne FCS-5030 user manual — IP Filtering
Page 58 · click to enlarge
Page 58

IP Filtering

LevelOne FCS-5030 — IP Filtering diagram (page 58)
Fig. 47 · IP Filtering

The access list is to control the access permission of clients by checking the client IP address.

There are two lists for permission control: Allow List and Deny List. Only those clients whose IP

address is in the Allow List and not in the Deny List can connect to the Video Server or Network

Camera for receiving the audio/video streaming.

Both Allow List and Deny List consist of a list of IP ranges. If you want to add a new IP address

range, type the Start IP Address and End IP Address in the text boxes and click on the Add

button. If you want to remove an existing IP address range, just select from the pull-down menu

and click on the Delete button.

Both the Allow List and Deny List can have 10 entries.

Page 59 of the LevelOne FCS-5030 user manual — Motion detection
Page 59 · click to enlarge
Page 59

Motion detection

“Enable motion detection” Check this option to turn on motion detection.

Click on this button to add a new window. At most three windows can exist simultaneously. Use the mouse to click, hold, and drag the window frame to resize or the title bar to move. Clicking

on the ‘x’ at the upper right-hand corner of the window deletes the window. Remember to save in

order to validate the changes.

Click on this button to save the related window settings. A graphic bar will rise or fall

depending on the image variation. A green bar means the image variation is under monitoring

level and a red bar means the image variation is over monitoring level. When the bar goes red, the

detected window will also be outlined in red. Going back to the homepage, the monitored window

is hidden but the red frame shows when motion is detected.

"Window Name" The text will show at the top of the window.

“Sensitivity” This sets the endurable difference between two sequential images.

“Percentage” This sets the space ratio of moving objects in the monitoring window. Higher

sensitivity and small percentage will allow easier motion detection.

The following figure shows the screen when

is clicked.

LevelOne FCS-5030 — Motion detection diagram (page 59)
Fig. 48 · Motion detection
Page 60 of the LevelOne FCS-5030 user manual — Event Setup
Page 60 · click to enlarge
Page 60

Event Setup

There are three sections in application page. They are event, server and media. Click

a window to add a new item of event, server or media. Click

to delete the selected item

from event, server or media. Click on the item name to pop a window to edit it.

There can be at most three events. There can be at most five server and five media

configurations.

User can know the event name, status, weekly and time schedule and trigger type in event

section. The server name, type and address/location are shown in server section.

The current media free space, media name and type are shown in media section. After adding a

new media, the value of free space will be updated. User cannot add media which size is larger

than media free space.

It is suggested to set server and media first before setting event. The servers and medias selected

in event list are not modified or deleted. Please remove them first from the event if you want to

delete or modify them. Recommend that using different media in different event to make use all

media be produced and received correctly. If using the same media in different events and the

events trigger almost simultaneously, the servers in the second triggered event will not receive

any media; there would be only notifications.

LevelOne FCS-5030 — Event Setup diagram (page 60)
Fig. 49 · Event Setup

to pop

Page 61 of the LevelOne FCS-5030 user manual — Event
Page 61 · click to enlarge
Page 61

Event

LevelOne FCS-5030 — Event diagram (page 61)
Fig. 50 · Event

“Event name” The unique name for event

“Enable this event” Check it to enable this event.

“Priority” The event with higher priority will be executed first.

“Delay second(s) before detecting next event” The delay to check next event. It is used in

motion detection and digital input trigger type.

There are four kinds of trigger supported.

“Video motion detection” Select the windows which need to be monitored.

“Periodic” The event is triggered in specified intervals. The unit of trigger interval is minute.

“Digital input” To monitor digital input

“System boot” The event is triggered when the system boots up.

The weekly and time schedules are provided.

“Sun” ~ “Sat” Select the days of the week to perform the event.

“Time” show “Always” or input the time interval.

Page 62 of the LevelOne FCS-5030 user manual — Server
Page 62 · click to enlarge
Page 62

The default action is triggering DO. If there are servers configured, the user can select them from

“Server name”, too.

“D/O” Check it to trigger digital output for specific seconds when event is triggered.

Server

LevelOne FCS-5030 — Server diagram (page 62)
Fig. 51 · Server

name” The unique name for server

There are four kinds of servers supported. They are email server, FTP server, HTTP server and

network storage.

Here is setting for email server.

“Sender email address” The email address of the sender

“Recipient email address” The email address of the recipient

“Server address” The domain name or IP address of the external email server.

“User name” This granted user name on the external email server.

“Password” This granted password on the external email server.

Here is setting for FTP server.

“Server

Page 63 of the LevelOne FCS-5030 user manual — Server
Page 63 · click to enlarge
Page 63

“Server address” The domain name or IP address of the external FTP server.

“Server port” This can be other than the default port 21. The user can change this value from

1025 to 65535.

“User name” This granted user name on the external FTP server.

“Password” This granted password on the external FTP server.

“Remote folder name” Granted folder on the external FTP server. The string must conform to

that of the external FTP server. Some FTP servers cannot accept preceding slash symbol before

the path without virtual path mapping. Refer to the instructions for the external FTP server for

details. The folder privilege must be open for upload.

“Passive Mode” Check it to enable passive mode in transmission.

Here is setting for HTTP server.

“URL” The URL to upload the media.

“User name” This granted user name on the external HTTP server.

“Password” This granted password on the external HTTP server.

Here is setting for network storage. Only one network storage is supported.

“Network storage location” The path to upload the media

“Workgroup” The workgroup for network storage.

“User name” This granted user name on the network storage.

“Password” This granted password on the network storage.

After input the setting of server, user can click on

to test whether the setting is correct. The testing result will be shown in a pop-up window.

Page 64 of the LevelOne FCS-5030 user manual — Media Setting
Page 64 · click to enlarge
Page 64

Media Setting

LevelOne FCS-5030 — Media Setting diagram (page 64)
Fig. 52 · Media Setting

“Media name” The unique name for media

There are three kinds of media. They are snapshot, video clip and system log.

Here is setting for snapshot.

“Source” The source of stream, stream1 or stream2.

“Send pre-event images” The number of pre-event images

“Send post-event images” The number of post-event images

“File Name Prefix” The prefix name will be added on the file name of the snapshot images.

“Add date and time suffix to file name” Check it to add timing information as file name suffix.

Here is setting for video clip

“Source” The source of stream, stream1 or stream2.

“Pre-event recording” The interval of pre-event recording in seconds

There are two limitations for video clip file.

“Maximum duration” The maximal recording file duration in seconds

“Maximum file size” The maximal file size would be generated.

Page 65 of the LevelOne FCS-5030 user manual — Media Setting
Page 65 · click to enlarge
Page 65

“File name prefix” The prefix name will be added on the file name of the video clip.

Page 66 of the LevelOne FCS-5030 user manual — Recording
Page 66 · click to enlarge
Page 66

Recording

The Network camera supports recording on network storage. The operation of editing recording

item is the same as the one in application page. User can know the recording name, status,

weekly and time schedule, stream source and destination of recording. There can be at most two

recording entries. To do recording on network storage, please add network storage server in

application page first.

LevelOne FCS-5030 — Recording diagram (page 66)
Fig. 53 · Recording
Page 67 of the LevelOne FCS-5030 user manual — Recording
Page 67 · click to enlarge
Page 67
LevelOne FCS-5030 — Recording diagram (page 67)
Fig. 54 · Recording

“Recording name” The unique name for recording entry

“Enable this recording” Check it to enable this event.

“Priority” The recording with higher priority will be executed first.

“Source” The source of stream, stream1 or stream2.

The weekly and time schedules are provided.

“Sun” ~ “Sat” Select the days of the week to perform the event.

“Time” shows “Always” or input the time interval.

“Destination” Network storage server user added.

“Max. recording capacity” The total size for cycle recording in Kbytes

“File size for each recording” The single file size in Kbytes

“File Name Prefix” The prefix name will be added on the file name of the recording.

Page 68 of the LevelOne FCS-5030 user manual — Peripherals
Page 68 · click to enlarge
Page 68

Peripherals

LevelOne FCS-5030 — Peripherals diagram (page 68)
Fig. 55 · Peripherals

“Digital input” Select High or Low to define normal status of the digital input. The current status is

shown, too.

“Digital output” Select Grounded or Open to define normal status of the digital output. The

current status is shown, too.

Page 69 of the LevelOne FCS-5030 user manual — System log
Page 69 · click to enlarge
Page 69

System log

The Network camera support log the system messages on remote server. The protocol is

compliant to RFC 3164. If you have external Linux server with syslogd service, use “-r” option to

turn on the facility for receiving log from remote machine. Or you can use some software on

Windows which is compliant to RFC 3164.

Check “Enable remote log” and input the “IP address” and “port” number of the log server to

enable the remote log facility.

In the “Current log”, it displays the current system log file. The content of the log provides useful

information about configuration and connection after system boot- up.

LevelOne FCS-5030 — System log diagram (page 69)
Fig. 56 · System log
Page 70 of the LevelOne FCS-5030 user manual — Maintenance
Page 70 · click to enlarge
Page 70

Maintenance

Five actions can be selected.

“Reboot system” Click the reboot button to restart system.

“Restore” Click it to restore all setting to factory default except setting in “Network type” in

network page.

“Factory default” Click on Factory default button on the configuration page to restore the factory

default settings. Any changes made so far will be lost and the system will be reset to the initial

factory settings. The system will restart and require the installer program to set up the network

again.

“Upgrade firmware” Select the firmware file and click upgrade button.

LevelOne FCS-5030 — Maintenance diagram (page 70)
Fig. 57 · Maintenance
Page 71 of the LevelOne FCS-5030 user manual — Reset and restore
Page 71 · click to enlarge
Page 71

Appendix

A. Troubleshooting

Reset and restore

There is a button in the cable of the Network Camera. It is used to reset the system or restore

the factory default settings. Sometimes resetting the system sets the system back to normal

state. If the system problems remain after reset, restore the factory settings and install again.

RESET: Click on the button.

RESTORE: Press on the reset button continuously for 30 seconds.

Restoring the factory defaults will erase any previous settings. Reset or

restore the system after power on.

Reset Button

Page 72 of the LevelOne FCS-5030 user manual — Style convention
Page 72 · click to enlarge
Page 72

B. URL commands of the Network Camera

Overview

For some customers who already have their own web site or web control application, Network

Camera/Video server can be easily integrated through convenient URLs. This section specifies

the external HTTP based application programming interface. The HTTP based camera

interface provides the functionality to request a single image, to control camera functions (PTZ,

output relay etc.) and to get and set internal parameter values. The image and CGI-requests

are handled by the built in Web server.

Style convention

In URL syntax and in descriptions of CGI parameters, a text within angle brackets denotes a

content that is to be replaced with either a value or a string. When replacing the text string also

the angle brackets shall be replaced. An example of this is the description of the name for the

server, denoted with in the URL syntax description below, that is replaced with

the string myserver in the URL syntax example, also below.

URL syntax' are written with the “Syntax:" word written in bold face followed by a box with the

referred syntax as seen below. The name of the server is written as . This is

intended to be replaced with the name of the actual server. This can either be a name, e.g.,

"mywebcam" or "thecam.adomain.net" or the associated IP number for the server, e.g.,

192.168.0.220.

Syntax:

http://<servername>/cgi-bin/viewer/video.jpg

Description of returned data is written with "Return:" in bold face followed by the returned data

in a box. All data returned as HTTP formatted, i.e., starting with the string HTTP is line

separated with a Carriage Return and Line Feed (CRLF) printed as \r\n.

Return:

HTTP/1.0 \r\n

URL syntax examples are written with "Example:" in bold face followed by a short description

and a light grey box with the example.

Page 73 of the LevelOne FCS-5030 user manual — Get server parameter values
Page 73 · click to enlarge
Page 73
Examplerequest a single snapshot image

http://mywebserver/cgi-bin/viewer/video.jpg

General CGI URL syntax and parameters

CGI parameters are written in lower-case and as one word without any underscores or other

separators. When the CGI request includes internal camera parameters, the internal

parameters must be written exactly as they are named in the camera or video server. The CGIs

are organized in function related directories under the cgi-bin directory. The file extension of the

CGI is required.

Syntax:

http://<servername>/cgi-bin/[/...]/.

[?=[&=...]]

ExampleSetting digital output #1 to active

http://mywebserver/cgi-bin/dido/setdo.cgi?do1=1

Security level

SECURITY

SUB-DIRECTORY DESCRIPTION

LEVEL

0 anonymous Unprotected.

1 [view] anonymous, viewer,

1. Can view, listen, talk to camera
2. Can control dido, ptz of camera

4 [operator] anonymous, viewer,

Operator’s access right can modify most of camera’s

parameters except some privilege and network

6 [admin] anonymous, viewer,

Administrator’s access right can fully control the

camera’s operation.

7 N/A Internal parameters. Unable to be changed by any

external interface.

Get server parameter values

MethodGET/POST
Show 5 more labels / short text on this page
dido, camctrl · dido, camctrl, operator · options · dido, camctrl, operator, · admin
Page 74 of the LevelOne FCS-5030 user manual — Maintenance
Page 74 · click to enlarge
Page 74

Syntax:

http://<servername>/cgi-bin/anonymous/getparam.cgi?[<parameter>]

http://<servername>/cgi-bin/viewer/getparam.cgi?[<parameter>]

http://<servername>/cgi-bin/operator/getparam.cgi?[<parameter>]

http://<servername>/cgi-bin/admin/getparam.cgi?[<parameter>]

where the <parameter> should be <group>[_<name>] or <group>[.<name>] If you do not

specify the any parameters, all the parameters on the server will be returned. If you specify only

<group>, the parameters of related group will be returned.

When query parameter values, the current parameter value are returned.

Successful control request returns paramter pairs as follows.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length<length>\r\n

where is

is the actual length of content.

Examplerequest IP address and it’s response

Request:

http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress

Response:

Show 8 more labels / short text on this page
[&<parameter>…] · [&<parameter>…] · [&<parameter>…] · [&<parameter>…] · \r\n · <parameter pair> · <parameter>=<value>\r\n · [<parameter pair>]
Page 75 of the LevelOne FCS-5030 user manual — PARAMETER VALUE DESCRIPTION
Page 75 · click to enlarge
Page 75

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length33\r\n

network.ipaddress=192.168.0.123\r\n

Set server parameter values

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/anonymous/setparam.cgi? <parameter>=<value>

http://<servername>/cgi-bin/viewer/setparam.cgi? <parameter>=<value>

http://<servername>/cgi-bin/operator/setparam.cgi? <parameter>=<value>

http://<servername>/cgi-bin/admin/setparam.cgi? <parameter>=<value>

PARAMETER VALUE DESCRIPTION

<group>_<name> value to assigned Assign <value> to the parameter <group>_<name>

update set to 1 to actually update all fields (no need to use update

parameter in each group)

return <return page> Redirect to the page <return page> after the parameter is

assigned. The <return page> can be a full URL path or

relative path according the the current path. If you omit this

parameter, it will redirect to an empty page.

(noteThe return page can be a general HTML

file(.htm, .html) or a LevelOne server script executable

(.vspx) file. It can not be a CGI command. It can not have

any extra parameters. This parameter must be put at end of

Show 5 more labels / short text on this page
\r\n · [&<parameter>=<value>…][&update=<value>][&return=<return page>] · [&<parameter>=<value>…][&update=<value>] [&return=<return page>] · [&<parameter>=<value>…][&update=<value>] [&return=<return page>] · [&<parameter>=<value>…][&update=<value>] [&return=<return page>]
Page 76 of the LevelOne FCS-5030 user manual — VALID VALUES DESCRIPTION
Page 76 · click to enlarge
Page 76

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length<length>\r\n

where is

Only the parameters that you set and readable will be returned.

ExampleSet the IP address of server to 192.168.0.123

Request:

http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123

Response:

HTTP/1.0 200 OK\r\n

Content-Typetext/html\r\n
Context-Length33\r\n

network.ipaddress=192.168.0.123\r\n

Available parameters on the server

Valid values:

VALID VALUES DESCRIPTION

string[] Text string shorter than ‘n’ characters

password[] The same as string but display ‘*’ instead

integer Any number between (-231 – 1) and (231 – 1)

positive integer Any number between 0 and (232 – 1)

~ Any number between ‘m’ and ‘n’

domain name[] A string limited to contain a domain name shorter than ‘n’ characters

(eg. www.ibm.com)

Show 6 more labels / short text on this page
parameter list) · \r\n · <parameter pair> · <parameter>=<value>\r\n · [<parameter pair>] · \r\n
Page 77 of the LevelOne FCS-5030 user manual — Maintenance
Page 77 · click to enlarge
Page 77
LevelOne FCS-5030 — Maintenance diagram (page 77)
Fig. 58 · Maintenance

email address [] A string limited to contain a email address shorter than ‘n’ characters

ip address A string limited to contain an ip address (eg. 192.168.1.1)

mac address A string limited to contain mac address without hyphen or colon

boolean A boolean value 1 or 0 represents [Yes or No], [True or False],

Groupsystem
LevelOne FCS-5030 — Maintenance diagram (page 77)
Fig. 59 · Maintenance

ledoff 6/6 turn on(0) or turn off(1) all led

lowlight 6/6 (0) Turn on white light LED in all

timezoneindex -489 ~ 529 6/6 Indicate timezone and area

Page 78 of the LevelOne FCS-5030 user manual — Maintenance
Page 78 · click to enlarge
Page 78
-480GMT-12:00 Eniwetok,
-440GMT-11:00 Midway Island,
-400GMT-10:00 Hawaii
-360GMT-09:00 Alaska
-320GMT-08:00 Las Vegas,
-280GMT-07:00 Mountain Time,
-281GMT-07:00 Arizona
-240GMT-06:00 Central America,
-200GMT-05:00 Eastern Time,
-201GMT-05:00 Bogota, Lima,
-160GMT-04:00 Atlantic Time,
-140GMT-03:30 Newfoundland
-120GMT-03:00 Brasilia, Buenos
-80GMT-02:00 Mid-Atlantic
-40GMT-01:00 Azores,

Cape_Verde_IS.

0. GMT Casablanca, Greenwich

Mean Time:Dublin,

40. GMT 01:00 Amsterdam, Berlin,

Stockholm, Vienna, Madrid, Paris

41. GMT 01:00 Warsaw, Budapest,
80. GMT 02:00 Athens, Helsinki,
Show 16 more labels / short text on this page
Kwajalein · Samoa · San_Francisco, · Vancouver · Denver · Central Time, · Mexico City, Saskatchewan · New York, Toronto · Quito, Indiana · Canada, Caracas · ,La Paz, Santiago · Aires, · Georgetown, Greenland · Edinburgh, Lisbon, London · Rome, · Bern
Page 80 of the LevelOne FCS-5030 user manual — <MODEL-BRAND-VERSION>
Page 80 · click to enlarge
Page 80

Solomon Is., New

480. GMT 12:00 Aucklan,

Marshall Is.

520. GMT 13:00 Nuku'Alofa

6/6 0 to Disable automatic time

adjustment, otherwise, it means

the seconds between NTP

automatic update interval.

7/6 Restore the system parameters to

default value. Restart the server

after seconds.

7/6 Restart the server after

seconds.

7/6 Restore the system parameters to

default value except (ipaddress,

subnet, router, dns1, dns2, ddns

settings). Restart the server after

seconds.

SubGroup of systeminfo (The fields in this group are unchangeable.)

NAME VALUE SECURITY

DESCRIPTION

modelname string[40] 0/7 model name of server

serialnumber 0/7 12 characters mac address without

firmwareversion string[40] 0/7 The version of firmware, including

model, company, and version

number in the format

<MODEL-BRAND-VERSION>

language_default string[16] 0/7 Default webpage language.

language_count <integer> 0/7 number of webpage language

available on the server

string[16] 0/7 Available language lists

Show 17 more labels / short text on this page
Caledonia · Wellington, Fiji, Kamchatka, · updateinterval 0, · 3600, · 86400, · 604800, · 2592000 · restore 0, · <positive integer> · reset 0, · <positive integer> · restoreexceptnet 0, · <positive integer> · (get/set) · hyphen connected · language_i<0~(count- · 1)>
Page 81 of the LevelOne FCS-5030 user manual — Maintenance
Page 81 · click to enlarge
Page 81
Groupstatus
LevelOne FCS-5030 — Maintenance diagram (page 81)
Fig. 60 · Maintenance
Groupdi_i<0~(ndi-1)>
LevelOne FCS-5030 — Maintenance diagram (page 81)
Fig. 61 · Maintenance
Groupdo_i<0~(ndo-1)>
LevelOne FCS-5030 — Maintenance diagram (page 81)
Fig. 62 · Maintenance
Groupsecurity
LevelOne FCS-5030 — Maintenance diagram (page 81)
Fig. 63 · Maintenance
Page 82 of the LevelOne FCS-5030 user manual — Maintenance
Page 82 · click to enlarge
Page 82
Groupnetwork
LevelOne FCS-5030 — Maintenance diagram (page 82)
Fig. 64 · Maintenance

resetip 6/6 1 => get ipaddress, subnet, router,

Subgroup of networkftp
LevelOne FCS-5030 — Maintenance diagram (page 82)
Fig. 65 · Maintenance
Subgroup of networkhttp
LevelOne FCS-5030 — Maintenance diagram (page 82)
Fig. 66 · Maintenance

s0_accessname string[32] 1/6 Http server push access name for

s1_accessname string[32] 1/6 Http server push access name for

admin

Page 83 of the LevelOne FCS-5030 user manual — NAME VALUE SECURITY
Page 83 · click to enlarge
Page 83
Subgroup of networkrtsp
LevelOne FCS-5030 — Maintenance diagram (page 83)
Fig. 67 · Maintenance
Subgroup of rtsp_s<0~(n-1)>multicast, n is stream count
LevelOne FCS-5030 — Maintenance diagram (page 83)
Fig. 68 · Maintenance

ttl 1 ~ 255 4/4 Mutlicast time to live value

Subgroup of networkrtp
LevelOne FCS-5030 — Maintenance diagram (page 83)
Fig. 69 · Maintenance

videoport 1025 ~ 65535 6/6 video channel port for RTP

audioport 1025 ~ 65535 6/6 audio channel port for RTP

Subgroup of networkpppoe
LevelOne FCS-5030 — Maintenance diagram (page 83)
Fig. 70 · Maintenance
Groupipfilter

NAME VALUE SECURITY

DESCRIPTION

(get/set)

Page 84 of the LevelOne FCS-5030 user manual — Maintenance
Page 84 · click to enlarge
Page 84
LevelOne FCS-5030 — Maintenance diagram (page 84)
Fig. 71 · Maintenance
Groupvideoin
LevelOne FCS-5030 — Maintenance diagram (page 84)
Fig. 72 · Maintenance
Groupvideoin_c<0~(n-1)> for n channel products, m is stream number
LevelOne FCS-5030 — Maintenance diagram (page 84)
Fig. 73 · Maintenance

ptzstatus 1/7 An 32-bits integer, each bit can be

Page 85 of the LevelOne FCS-5030 user manual — Maintenance
Page 85 · click to enlarge
Page 85

Bit 4 => Support zoom

operation. 0(not support),

Bit 5 => Support focus operation.

text string[16] 1/4 enclosed caption

imprinttimestamp 4/4 Overlay time stamp on video

maxexposure 1~120 4/4 Maximum exposure time

mpeg4, mjpeg 4/4 video codec type

1, 3, 5, 10, 30,

4/4 Key frame interval

4/4 Video resolution in pixel

cbr, vbr 4/4 cbr, constant bitrate

s_quant 1, 2, 3, 4, 5 4/4 quality of video when choosing vbr

in “ratecontrolmode”. 1 is worst

quality and 5 is the best quality.

4/4 set bit rate in bps when choose cbr

Show 33 more labels / short text on this page
0(not support), 1(support) · 1(support) · 0(not support), 1(support) · s<0~(m-1)>_codectyp · e · s<0~(m-1)>_keyinterv · al · 60, 90, 120 · s<0~(m-1)>_resolution · 176x144, · 320x240, · 640x480, · 800x600, · 1280x1024 · s<0~(m-1)>_ratecontr · olmode · vbr, fix quality · s<0~(m-1)>_bitrate 20000, · 30000, · in “ratecontrolmode” · 40000, · 50000, · 64000, · 128000, · 256000, · 384000, · 512000, · 768000, · 1000000, · 1200000, · 1500000, · 2000000, · 3000000,
Page 86 of the LevelOne FCS-5030 user manual — Maintenance
Page 86 · click to enlarge
Page 86
LevelOne FCS-5030 — Maintenance diagram (page 86)
Fig. 74 · Maintenance
Groupaudioin_c<0~(n-1)> for n channel products
LevelOne FCS-5030 — Maintenance diagram (page 86)
Fig. 75 · Maintenance

s_codectype aac4, gamr 4/4 set audio codec type for input

Groupimage_c<0~(n-1)> for n channel products
LevelOne FCS-5030 — Maintenance diagram (page 86)
Fig. 76 · Maintenance

saturation -5 ~ 5 4/4 Adjust saturation of image

Page 87 of the LevelOne FCS-5030 user manual — Maintenance
Page 87 · click to enlarge
Page 87
LevelOne FCS-5030 — Maintenance diagram (page 87)
Fig. 77 · Maintenance

contrast -5 ~ 5 4/4 Adjust contrast of image according

hue -5 ~ 5 4/4 Adjust hue of image according to

Groupmotion_c<0~(n-1)> for n channel product
LevelOne FCS-5030 — Maintenance diagram (page 87)
Fig. 78 · Maintenance

win_i _name string[14] 4/4 name of motion window 1~3

win_i _left 0 ~ 320 4/4 Left coordinate of window position.

win_i _top 0 ~ 240 4/4 Top coordinate of window position.

win_i _width 0 ~ 320 4/4 Width of motion detection window.

win_i_height 0 ~ 240 4/4 Height of motion detection window.

win_i_objsize 0 ~ 100 4/4 Percent of motion detection

win_i_sensitivity 0 ~ 100 4/4 Sensitivity of motion detection

Groupddns
LevelOne FCS-5030 — Maintenance diagram (page 87)
Fig. 79 · Maintenance
Page 88 of the LevelOne FCS-5030 user manual — Maintenance
Page 88 · click to enlarge
Page 88
LevelOne FCS-5030 — Maintenance diagram (page 88)
Fig. 80 · Maintenance

string[64] 6/6 Your user or email to login ddns

string[64] 6/6 Your password or key to login ddns

Groupupnppresentation
LevelOne FCS-5030 — Maintenance diagram (page 88)
Fig. 81 · Maintenance
Groupupnpportforwarding
LevelOne FCS-5030 — Maintenance diagram (page 88)
Fig. 82 · Maintenance

enable 6/6 Enable or disable the UPNP port

0 is OK, 1 is FAIL, 2 is no IGD

Groupsyslog
LevelOne FCS-5030 — Maintenance diagram (page 88)
Fig. 83 · Maintenance
Page 89 of the LevelOne FCS-5030 user manual — Maintenance
Page 89 · click to enlarge
Page 89
LevelOne FCS-5030 — Maintenance diagram (page 89)
Fig. 84 · Maintenance
Groupprivacymask_c<0~(n-1)> for n channel product
LevelOne FCS-5030 — Maintenance diagram (page 89)
Fig. 85 · Maintenance

win_i_name string[14] 4/4 The name of privacy mask window

win_i_left 0 ~ 320/352 4/4 Left coordinate of window position.

win_i_top 0 ~ 240/288 4/4 Top coordinate of window position.

win_i_width 0 ~ 320/352 4/4 Width of privacy mask window

win_i_height 0 ~ 240/288 4/4 Height of privacy mask window

Groupcapability
LevelOne FCS-5030 — Maintenance diagram (page 89)
Fig. 86 · Maintenance
Page 90 of the LevelOne FCS-5030 user manual — Maintenance
Page 90 · click to enlarge
Page 90
LevelOne FCS-5030 — Maintenance diagram (page 90)
Fig. 87 · Maintenance

ptzenabled < boolean > 0/7 indicate whether to support PTZ

protocol_https < boolean > 0/7 indicate whether to support http

protocol_rtsp < boolean > 0/7 indicate whether to support rtsp

videoin_type 0, 1, 2 0/7 0 => Interlaced CCD

videoin_resolution

Page 91 of the LevelOne FCS-5030 user manual — Maintenance
Page 91 · click to enlarge
Page 91

videoin_codec

0/7 available codec list

videoout_codec

0/7 available codec list

audio_aec 0/7 indicate whether to support

audio_extmic 0/7 indicate whether to support

audio_linein 0/7 indicate whether to support

audio_lineout 0/7 indicate whether to support line

audio_headphoneout 0/7 indicate whether to support

audioin_codec

0/7 available codec list

audioout_codec

0/7 available codec list

camctrl_httptunnel 0/7 Indicate whether to support the

http tunnel for camera control

uart_httptunnel 0/7 Indicate whether to support the

http tunnel for uart transfer

Show 25 more labels / short text on this page
available · resolution · separates by · comma) · available codec · types · separaters by · comma) · available codec · types · separaters by · comma) · acoustic echo cancellation · external microphone input · external line input · output · headphone output · available codec · types · separaters by · comma) · available codec · types · separaters by · comma)
Page 92 of the LevelOne FCS-5030 user manual — Maintenance
Page 92 · click to enlarge
Page 92
LevelOne FCS-5030 — Maintenance diagram (page 92)
Fig. 88 · Maintenance
Groupevent_i<0~2>
LevelOne FCS-5030 — Maintenance diagram (page 92)
Fig. 89 · Maintenance

enable 0, 1 6/6 To enable or disable this event.

priority 0, 1, 2 6/6 Indicate the priority of this event.

delay 1~999 6/6 Delay seconds before detect next event.

Page 93 of the LevelOne FCS-5030 user manual — Maintenance
Page 93 · click to enlarge
Page 93

di 6/6 Indicate which di detected.

This field is required when trigger condition

is “di”.

One bit represents one digital input. The

LSB indicates DI 0.

mdwin 6/6 Indicate which motion detection windows

detected.

This field is required when trigger condition

is “md”.

One bit represents one window.

The LSB indicates the 1st window.

For example, to detect the 1st and 3rd

windows, set mdwin as 5.

inter 1~999 6/6 Interval of period snapshot in minute.

This field is used when trigger condition is

“seq”.

weekday 6/6 Indicate which weekday is scheduled.

One bit represents one weekday.

The bit0 (LSB) indicates Saturday.

The bit1 indicates Friday.

The bit2 indicates Thursday.

The bit3 indicates Wednesday.

The bit4 indicates Tuesday.

The bit5 indicates Monday.

The bit6 indicates Sunday.

For example, to detect events on Friday and

Sunday, set weekday as 66.

begintime hh:mm 6/6 Begin time of weekly schedule.

endtime hh:mm 6/6 End time of weekly schedule.

(00:00 ~ 24:00 means always.)

0, 1 6/6 To enable or disable trigger digital output.

1~999 6/6 The duration of digital output is triggered in

seconds.

0, 1 6/6 To enable or disable this server action.

The default value is 0.

NULL, 0~4 6/6 The index of attached media.

Show 8 more labels / short text on this page
action_do_i<0~(ndo-1) · >_enable · action_do_i<0~(ndo-1) · >_duration · action_server_i<0~4>_ · enable · action_server_i<0~4>_ · media
Page 94 of the LevelOne FCS-5030 user manual — PARAMETER VALUE SECURITY
Page 94 · click to enlarge
Page 94
Groupserver_i<0~4>
LevelOne FCS-5030 — Maintenance diagram (page 94)
Fig. 90 · Maintenance

http_url string[128] 6/6 The url of http server to upload.

http_username string[64] 6/6 The username to login in the server.

ftp_username string[64] 6/6 The username to login in the server.

ftp_port 0~65535 6/6 The port to connect the server.

ftp_location string[128] 6/6 The location to upload or store the media.

ftp_passive 0, 1 6/6 To enable or disable the passive mode.

email_username string[64] 6/6 The username to login in the server.

ns_location string[128] 6/6 The location to upload or store the media.

ns_username string[64] 6/6 The username to login in the server.

Groupmedia_i<0~4>

PARAMETER VALUE SECURITY

DESCRIPTION

(get/set)

Page 95 of the LevelOne FCS-5030 user manual — Maintenance
Page 95 · click to enlarge
Page 95
LevelOne FCS-5030 — Maintenance diagram (page 95)
Fig. 91 · Maintenance

6/6 The media type to send to the server or

snapshot_source 6/6 Indicate the source of media stream.

snapshot_prefix string[16] 6/6 Indicate the prefix of the filename.

snapshot_datesuffix 0, 1 6/6 To add date and time suffix to filename or

snapshot_preevent 0 ~ 7 6/6 It indicates the number of pre-event images.

snapshot_postevent 0 ~ 7 6/6 The number of post-event images.

videoclip_source 6/6 Indicate the source of media stream.

videoclip_prefix string[16] 6/6 Indicate the prefix of the filename.

videoclip_preevent 0 ~ 9 6/6 It indicates the time of pre-event recording

videoclip_maxduration 1 ~ 10 6/6 The time of maximum duration of one video

videoclip_maxsize 50 ~ 1500 6/6 The maximum size of one video clip file in

Grouprecord_i<0~1>
LevelOne FCS-5030 — Maintenance diagram (page 95)
Fig. 92 · Maintenance

enable 0, 1 6/6 To enable or disable this recoding.

priority 0, 1, 2 6/6 Indicate the priority of this recoding.

Page 96 of the LevelOne FCS-5030 user manual — PARAMETER VALUE DESCRIPTION
Page 96 · click to enlarge
Page 96

source 6/6 Indicate the source of media stream.

0 means the first stream.

1 means the second stream and etc.

weekday 6/6 Indicate which weekday is scheduled.

One bit represents one weekday.

The bit0 (LSB) indicates Saturday.

The bit1 indicates Friday.

The bit2 indicates Thursday.

The bit3 indicates Wednesday.

The bit4 indicates Tuesday.

The bit5 indicates Monday.

The bit6 indicates Sunday.

For example, to detect events on Friday and

Sunday, set weekday as 66.

begintime hh:mm 6/6 Begin time of weekly schedule.

endtime hh:mm 6/6 End time of weekly schedule.

(00:00~24:00 means always.)

prefix string[16] 6/6 Indicate the prefix of the filename.

cyclesize 6/6 The maximum size for cycle recording in

Kbytes.

maxfilesize 200~6000 6/6 The max size for one file in Kbytes

dest 0~4 6/6 The destination to store the recording data.

“0~4” means the index of network storage.

Drive the digital output

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/dido/setdo.cgi?do1=<state>[&do2=]

[&do3=][&do4=][&return=<return page>]

Where state is 0, 1. “0” means inactive or normal state while “1” means active or triggered state.

PARAMETER VALUE DESCRIPTION

Page 97 of the LevelOne FCS-5030 user manual — Query status of the digital input
Page 97 · click to enlarge
Page 97
0. inactive, normal state do 0, 1
1. active, triggered state

return <return page> Redirect to the page <return page> after the parameter

is assigned. The <return page> can be a full URL path or

relative path according the the current path. If you omit

this parameter, it will redirect to an empty page.

ExampleDrive the digital output 1 to triggered state and redirect to an empty page

http://myserver/cgi-bin/dido/setdo.cgi?do1=1

Query status of the digital input

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/dido/getdi.cgi?[di0][&di1][&di2][&di3]

If no parameter is specified, all the status of digital input will be returned.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length<length> \r\n

where <state> can be 0 or 1.

ExampleQuery the status of digital input 1

Request:

http://myserver/cgi-bin/dido/getdi.cgi?di1

Show 5 more labels / short text on this page
\r\n · [di0=<state>]\r\n · [di1=<state>]\r\n · [di2=<state>]\r\n · [di3=<state>]\r\n
Page 98 of the LevelOne FCS-5030 user manual — Query status of the digital output
Page 98 · click to enlarge
Page 98

Response:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length7\r\n

Query status of the digital output

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/dido/getdo.cgi?[do0][&do1][&do2][&do3]

If no parameter is specified, all the status of digital output will be returned.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length<length> \r\n

where <state> can be 0 or 1.

ExampleQuery the status of digital output 1

Request:

http://myserver/cgi-bin/dido/getdo.cgi?do1

Response:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length7\r\n
Show 8 more labels / short text on this page
\r\n · di1=1\r\n · \r\n · [do0=<state>]\r\n · [do1=<state>]\r\n · [do2=<state>]\r\n · [do3=<state>]\r\n · \r\n
Page 99 of the LevelOne FCS-5030 user manual — Account management
Page 99 · click to enlarge
Page 99

Capture single snapshot

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/viewer/video.jpg?[channel=][&resolution=]

If the user requests the size larger than all stream setting on the server, this request will failed!

PARAMETER VALUE DEFAULT DESCRIPTION

channel 0~(n-1) 0 the channel number of video source

0 The resolution of image

quality 1~5 3 The quality of image

Server will return the most up-to-date snapshot of selected channel and stream in JPEG format.

The size and quality of image will be set according to the video settings on the server.

Return:

HTTP/1.0 200 OK\r\n

Content-Typeimage/jpeg\r\n
[Content-Length<image size>\r\n]

<binary JPEG image data>

Account management

MethodGET/POST

Syntax:

Show 4 more labels / short text on this page
do1=1\r\n · [&quality=<value>] · resolution <available · resolution>
Page 100 of the LevelOne FCS-5030 user manual — System logs
Page 100 · click to enlarge
Page 100

http://<servername>/cgi-bin/admin/editaccount.cgi?

method=&username=<name>[&userpass=<value>][&privilege=<value>]

[&privilege=][…][&return=<return page>]

PARAMETER VALUE DESCRIPTION

add Add an account to server. When using this method,

“username” field is necessary. It will use default value of

other fields if not specified.

delete Remove an account from server. When using this

method, “username” field is necessary, and others are

ignored.

edit Modify the account password and privilege. When using

this method, “username” field is necessary, and other

fields are optional. If not specified, it will keep original

settings.

username The name of user to add, delete or edit

userpass The password of new user to add or that of old user to

modify. The default value is an empty string.

The privilege of user to add or to modify.

return Redirect to the page <return page> after the parameter is

assigned. The <return page> can be a full URL path or

relative path according the the current path. If you omit

this parameter, it will redirect to an empty page.

System logs

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/syslog.cgi

Show 5 more labels / short text on this page
method · privilege · viewer viewer’s privilege · operator operator’s privilege · admin administrator’s privilege
Page 101 of the LevelOne FCS-5030 user manual — IP filtering
Page 101 · click to enlarge
Page 101

Server will return the up-to-date system log.

Return:

HTTP/1.0 200 OK\r\n

Content-Typetext/plain\r\n
Content-Length<syslog length>\r\n

Upgrade firmware

MethodPOST

Syntax:

http://<servername>/cgi-bin/admin/upgrade.cgi

Post data:

Server will accept the upload file named to be upgraded the firmware and return

with if indicated.

IP filtering

MethodGET/POST

Syntax:

http://<servername>/cgi-bin/admin/ipfilter.cgi?

method=&[start=<ipaddress>&end=<ipaddress>][&index=]

Show 5 more labels / short text on this page
\r\n · <system log information>\r\n · fimage=<file name>[&return=<return page>]\r\n · \r\n · [&return=<return page>]
Page 102 of the LevelOne FCS-5030 user manual — RTSP SDP
Page 102 · click to enlarge
Page 102

PARAMETER VALUE DESCRIPTION

addallow Add a set of allow IP address range to server. Start

and end parameters must be specified. If the index

parameter is specified, it will try to add starting from

index position.

adddeny Add a set of deny IP address range to server. Start and

end parameters must be specified. If the index

parameter is specified, it will try to add starting from

index position.

deleteallow Remove a set of allow IP address range from server. If

start and end parameters are specified, it will try to

remove the matched IP address. If index is specified, it

will try to remove the address from given index position.

[start, end] parameters have higher priority then the

[index] parameter.

deletedeny Remove a set of deny IP address range from server. If

start and end parameters are specified, it will try to

remove the matched IP address. If index is specified, it

will try to remove the address from given index position.

[start, end] parameters have higher priority then the

[index] parameter.

start The start IP address to add or to delete.

end The end IP address to add or to delete.

index The start position to add or to delete.

return Redirect to the page <return page> after the parameter

is assigned. The <return page> can be a full URL path or

relative path according the the current path. If you omit

this parameter, it will redirect to an empty page.

RTSP SDP

MethodGET/POST

Syntax:

http://<servername>/viewer//

Method

Page 103 of the LevelOne FCS-5030 user manual — Maintenance
Page 103 · click to enlarge
Page 103

rtsp:////

“n” is the channel number and “m” is the stream number.

You can get the SDP by HTTP or just describe by RTSP protocol directly. For detailed streaming

protocol, please refer to “control signaling” and “data format” documents.

Page 104 of the LevelOne FCS-5030 user manual — D. Specifications
Page 104 · click to enlarge
Page 104

D. Specifications

- System RAM: 64MB SDRAM ROM: 8MB FLASH ROM - Networking Protocol TCP/IP, HTTP, SMTP, FTP, DDNS, UPnP, Telnet, NTP, DNS, DHCP and RTSP Physical 10 baseT or 100 baseT Fast Ethernet auto negotiation - Video Algorithm supported MPEG4(simple profile) for streaming video JPEG for still image Features Adjustable image size, quality and bit rate Time stamp and text overlay 3 motion detection windows Resolution 704x480 pixels(NTSC) 704x576 pixels(PAL) - Camera Specification 1/3 inch colour CCD 176x120: 30/25fps 352x240: 30/25fps 704x480: 30/25fps 0Lux/F2.0 when IR on - Lens 8mm, F2.0 -IR LEDs 12 crystal IR LEDs for night view up to 30 meters - Audio AAC, GSM-AMR

158mm(L) x 105mm(W) x 108mm(H) - Weight NET. 1010g

- Power 12V/1.5A - Operating Environment Temperature: 0-50°C/32-122°F Humidity: 95%RH

- Dimension

Page 105 of the LevelOne FCS-5030 user manual — - EMI & Safety
Page 105 · click to enlarge
Page 105

- EMI & Safety

CE, FCC - Viewing system requirement

Operating system Microsoft Windows 2000/XP/VISTA Browser Internet Explorer 6.x or above Firefox 1.5.0.x or above

Page 106 of the LevelOne FCS-5030 user manual — 6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE
Page 106 · click to enlarge
Page 106

Technology License Notice MPEG-4 AAC Technology

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS

PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT

REGARD TO PC SOFTWARE, YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL

PURPOSES. FOR MORE INFORMATION, PLEASE REFER TO

HTTP://WWW.VIALICENSING.COM

MPEG-4 Visual Technology

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO

LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i)

ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4

VIDEO") AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER

ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED

FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO

LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL

INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND

COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE

HTTP://WWW.MPEGLA.COM

AMR-NB Standard

THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE

AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING

LICENSORS’ PATENTS MAY APPLY:

TELEFONAKIEBOLAGET ERICSSON ABUS PAT. 6192335; 6275798; 6029125; 6424938;

6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE

CORPORATIONAT PAT. 0516621; BE PAT. 0516621; CA PAT. 2010830; CH PAT. 0516621;

DE PAT. 0516621; DK PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621; GB PAT.

0516621; GR PAT. 0516621; IT PAT. 0516621; LI PAT. 0516621; LU PAT. 0516621; NL PAT.

0516621; SE PAT 0516621; US PAT 5444816; AT PAT. 819303/AT E 198805T1; AU PAT.

697256; BE PAT. 819303; BR PAT. 9604838-7; CA PAT. 2216315; CH PAT. 819303; CN PAT.

ZL96193827.7; DE PAT. 819303/DE69611607T2; DK PAT. 819303; ES PAT. 819303; EP PAT.

819303; FR PAT. 819303; GB PAT. 819303; IT PAT. 819303; JP PAT. APP. 8-529817; NL PAT.

819303; SE PAT. 819303; US PAT. 5664053. THE LIST MAY BE UPDATED FROM TIME TO

Page 107 of the LevelOne FCS-5030 user manual — Maintenance
Page 107 · click to enlarge
Page 107

TIME BY LICENSORS AND A CURRENT VERSION OF WHICH IS AVAILABLE ON

LICENSOR’S WEBSITE AT HTTP://WWW.VOICEAGE.COM

Page 108 of the LevelOne FCS-5030 user manual — Liability
Page 108 · click to enlarge
Page 108

Electromagnetic Compatibility (EMC)

This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions.

  • This device may not cause harmful interference, and
  • This device must accept any interference received, including interference that may cause undesired operation.

USA - This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a partial installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the seperation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables must be used in order to comply with emission limits.

- This digital equipment fulfills the requirement for radiated emission according to limit B of

EN55022/1998, and the requirement for immunity according to EN50082-1/1992.

Liability

LevelOne Inc. cannot be held responsible for any technical or typographical errors and reserves the right to make

changes to the product and manuals without prior notice. LevelOne Inc. makes no warranty of any kind with regard to

the material contained within this document, including, but not limited to, the implied warranties of merchantability and

fitness for any particular purpose.

Europe

Page 109 of the LevelOne FCS-5030 user manual — GNU GENERAL PUBLIC LICENSE
Page 109 · click to enlarge
Page 109

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright (C) 1989, 1991 Free Software Foundation, Inc.

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but

changing it is not allowed.

The licenses for most software are designed to take away your freedom to share and change it.

By contrast, the GNU General Public License is intended to guarantee your freedom to share

and change free software--to make sure the software is free for all its users. This General

Public License applies to most of the Free Software Foundation's software and to any other

program whose authors commit to using it. (Some other Free Software Foundation software is

covered by the GNU Library General Public License instead.) You can apply it to your

programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public

Licenses are designed to make sure that you have the freedom to distribute copies of free

software (and charge for this service if you wish), that you receive source code or can get it if

you want it, that you can change the soft-ware or use pieces of it in new free programs; and

that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights

or to ask you to surrender the rights. These restrictions translate to certain responsibilities for

you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must

give the recipients all the rights that you have. You must make sure that they, too, receive or

can get the source code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license

which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone

understands that there is no warranty for this free software. If the software is modified by

someone else and passed on, we want its recipients to know that what they have is not the

original, so that any problems introduced by others will not reflect on the original authors'

reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the

Preamble

Page 110 of the LevelOne FCS-5030 user manual — GNU GENERAL PUBLIC LICENSE
Page 110 · click to enlarge
Page 110

making the program proprietary. To prevent this, we have made it clear that any patent must

be licensed for everyone's free use or not licensed at all. The precise terms and conditions for

copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE

Terms And Conditions For Copying, Distribution And Modification

0. This License applies to any program or other work which contains a notice placed by the

copyright holder saying it may be distributed under the terms of this General Public License.

The "Program", below, refers to any such program or work, and a "work based on the

Program" means either the Program or any derivative work under copyright law: that is to say,

a work containing the Program or a portion of it, either verbatim or with modifications and/or

translated into another language. (Hereinafter, translation is included without limitation in the

term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License;

they are outside its scope. The act of running the Program is not restricted, and the output from

the Program is covered only if its contents constitute a work based on the Program

(independent of having been made by running the Program). Whether that is true depends on

what the Program does.

1. You may copy and distribute verbatim copies of the Program's source code as you receive it,

in any medium, provided that you conspicuously and appropriately publish on each copy an

appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to

this License and to the absence of any warranty; and give any other recipients of the Program

a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option

offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a work

based on the Program, and copy and distribute such modifications or work under the terms of

Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modified files to carry prominent notices stating that you changed the

files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is

derived from the Program or any part thereof, to be licensed as a whole at no charge to all third

parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it,

when started running for such interactive use in the most ordinary way, to print or display an

Page 111 of the LevelOne FCS-5030 user manual — Maintenance
Page 111 · click to enlarge
Page 111

announcement including an appropriate copyright notice and a notice that there is no warranty

(or else, saying that you provide a warranty) and that users may redistribute the program under

these conditions, and telling the user how to view a copy of this License. (Exception: if the

Program itself is interactive but does not normally print such an announcement, your work

based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work

are not derived from the Program, and can be reasonably considered independent and

separate works in themselves, then this License, and its terms, do not apply to those sections

when you distribute them as separate works. But when you distribute the same sections as

part of a whole which is a work based on the Program, the distribution of the whole must be on

the terms of this License, whose permissions for other licensees extend to the entire whole,

and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this

section to claim rights or contest your rights to work written entirely by you; rather, the intent is

to exercise the right to control the distribution of derivative or collective works based on the

Program.

In addition, mere aggregation of another work not based on the Program with the Program (or

with a work based on the Program) on a volume of a storage or distribution medium does not

bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object

code or executable form under the terms of Sections 1 and 2 above provided that you also do

one of the following:

a) Accompany it with the complete corresponding machine-readable source code, which must

be distributed under the terms of Sections 1 and 2 above on a medium customarily used for

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a

charge no more than your cost of physically performing source distribution, a complete

machine-readable copy of the corresponding source code, to be distributed under the terms of

Sections 1 and 2 above on a medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute corresponding

source code. (This alternative is allowed only for noncommercial distribution and only if you

received the program in object code or executable form with such an offer, in accord with

Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it.

For an executable work, complete source code means all the source code for all modules it

contains, plus any associated interface definition files, plus the scripts used to control

compilation and installation of the executable. However, as a special exception, the source

code distributed need not include anything that is normally distributed (in either source or

software interchange; or,

Page 112 of the LevelOne FCS-5030 user manual — Maintenance
Page 112 · click to enlarge
Page 112

binary form) with the major components (compiler, kernel, and so on) of the operating system

on which the executable runs, unless that component itself accompanies the executable.

If distribution of executable or object code is made by offering access to copy from a

designated place, then offering equivalent access to copy the source code from the same

place counts as distribution of the source code, even though third parties are not compelled to

copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly

provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute

the Program is void, and will automatically terminate your rights under this License. However,

parties who have received copies, or rights, from you under this License will not have their

licenses terminated so long as such parties remain in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing

else grants you permission to modify or distribute the Program or its derivative works. These

actions are prohibited by law if you do not accept this License. Therefore, by modifying or

distributing the Program (or any work based on the Program), you indicate your acceptance of

this License to do so, and all its terms and condi-tions for copying, distributing or modifying the

Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient

automatically receives a license from the original licensor to copy, distribute or modify the

Program subject to these terms and conditions. You may not impose any further restrictions on

the recipients' exercise of the rights granted herein. You are not responsible for enforcing

compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other

reason (not limited to patent issues), conditions are imposed on you (whether by court order,

agreement or otherwise) that contradict the conditions of this License, they do not excuse you

from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your

obligations under this License and any other pertinent obligations, then as a consequence you

may not distribute the Program at all. For example, if a patent license would not permit

royalty-free redistribution of the Program by all those who receive copies directly or indirectly

through you, then the only way you could satisfy both it and this License would be to refrain

entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance,

the balance of the section is intended to apply and the section as a whole is intended to apply

in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right

claims or to contest validity of any such claims; this section has the sole purpose of protecting

the integrity of the free software distribution system, which is implemented by public license

Page 113 of the LevelOne FCS-5030 user manual — Maintenance
Page 113 · click to enlarge
Page 113

practices. Many people have made generous contributions to the wide range of software

distributed through that system in reliance on consis-tent application of that system; it is up to

the author/donor to decide if he or she is willing to distribute software through any other system

and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the

rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by

patents or by copyrighted interfaces, the original copyright holder who places the Program

under this License may add an explicit geographical distribution limitation excluding those

countries, so that distribution is permitted only in or among countries not thus excluded. In

such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General

Public License from time to time. Such new versions will be similar in spirit to the present

version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version

number of this License which applies to it and "any later version", you have the option of

following the terms and condi-tions either of that version or of any later version published by

the Free Software Foundation. If the Program does not specify a version number of this

License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution

conditions are different, write to the author to ask for permission. For software which is

copyrighted by the Free Software Foundation, write to the Free Software Foundation; we

sometimes make exceptions for this. Our decision will be guided by the two goals of preserving

the free status of all derivatives of our free software and of promoting the sharing and reuse of

software generally.

Page 114 of the LevelOne FCS-5030 user manual — FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
Page 114 · click to enlarge
Page 114

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.

EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR

OTHER PARTIES

PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS

WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF

ALL NECESSARY SERVICING,

REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN

WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY

AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU

FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE

PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A

FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF

SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

This product incorporates open source code into the software and therefore falls under the

guidelines governed by the General Public License (GPL) agreement.

Adhering to the GPL requirements, the open source code and open source license for the

source code are available for free download at http://global.level1.com

If you would like a copy of the GPL or other open source code in this software on a physical CD

medium, LevelOne (Digital Data Communications) offers to mail this CD to you upon request,

for a price of US$9.99 plus the cost of shipping.

LevelOne FCS-5030 — FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR diagram (page 114)
Fig. 93

Ask about the LevelOne FCS-5030

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LevelOne FCS-5030

Be the first to ask — other owners or our team will answer.

Original document

LevelOne FCS-5030 manual PDF

114 pages·3.8 MB·Security Camera·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…