Instruction/ maintenance manual of the product OR1213 Jumppod
Go to page of 23
YJ USA Corp., 3970 Lindbergh Drive Adison, TX 75001 www .jumppod.com 877-928-8777 WARNING.
.
3.
3. Place the trampoline and trampoline enclosure on a level surface before use. 4. Must place the trampoline on lawn, bark wood chip, sand or cushioning materials. 5. Adequate overhead clearance is essential. A minimum of 7.3 m (24 ft) from ground level is recommended.
5 25. Do not attach anything to the barrier that is not a manufacturer approved accessory or part of the enclosure system. 26. Wear clothing free of drawstrings, hooks, loops, or anything that could get caught in the barrier . 27. Enter and exit the trampoline enclosure only at the door designed for that purpose.
6 Note: The.
.
.
.
.
the sharply spot..
.
.
1 4.
15 1. Make sure you understand the information in the box at the top of this page before you begin assembling the trampoline. Lay three T op T ubes (1), (2) and (3) on the ground as shown.
16 ３ F rame Holes V-rings 8 10 10 10 10 S p r i n gs (10) 22 Hook the V-ring V-ring 8 10 10 F rame Black webbing with yellow line No yellow line 3. Lay the Bed (8) on the ground inside of the assembled frame. Make sure that the two warn- ing decals (not shown) are on top of the Bed.
17 4 4. Lay the Frame Pad (9) on the frame. Do not use the trampoline without the Frame Pad (9) , which is designed to reduce the likelihood of injury to the user from coming in con- tact with the trampoline frame. If you do not have a Frame Pad, call our Customer Hot Line toll-free at 877-927-8777, Monday-Friday,8 a.
6. Using the included plastic tie, attach the Safety Placard (11) to the frame near the point where jumpers will climb onto and off the trampoline. The trampoline is now fully assembled.
10. Attach the other three Pole(16,17) in the same way. See inset drawing. 10 19 １６ １７ １１ 1 1. Lay out T op G3 Pole (18), joint each section Connector to a straight line as shown.
Attach the first hanging point at the upper edge of the Netting (20) with the G3 Pole (18) to the Hemisphere Cap (19) of T op enclosure pole(17). Attach a second hanging point directly across the Netting (20) from the first hanging point.
15. Using the included plastic tie,attach the Safety Placard(10)to the Netting(20) near the door as shown. The trampoline/enclosure is now fully assembled.
22 It is possible for the trampoline/enclosure be blown about by high wind. If you anticipate high winds, the trampoline/enclosure should be moved to a sheltered location, disassembled, or tied down to the ground with ropes and stakes (not included). At least three ropes and three stakes should be used.
1 4 T op Tu be(With T-connector, A marking) 2 4 Top Tube(With Socket, B marking) 3 4 Top Tube(With T-connector, C marking) 4 8 T-Connector 5 8 Leg Extension 6 4 Center 7 4 Socket 8 1 Stitched Bed with V-ring 9 1 Frame Pad 1 58 U-bolts 16 4 Bottom enclosure pole 17 4 Top enclosure pole 18 2 G3 Pole (Black) 10 60 5.
An important point after buying a device Jumppod OR1213 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Jumppod OR1213 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Jumppod OR1213 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Jumppod OR1213 you will learn all the available features of the product, as well as information on its operation. The information that you get Jumppod OR1213 will certainly help you make a decision on the purchase.
If you already are a holder of Jumppod OR1213, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Jumppod OR1213.
However, one of the most important roles played by the user manual is to help in solving problems with Jumppod OR1213. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Jumppod OR1213 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
