EN
InFocus logo
Official user manual

InFocus W50

51 pages·2.3 MB·Projector·PDF·ENDEFRITNLJA
InFocus W50
Table of Contents 71 sections IN 5102 /IN 5104 /IN 5106 · Regulatory models W50, W55 User’s Guide · Battery Safety Information · UL, CUL · … ShowHide
IN 5102 /IN 5104 /IN 5106p.1Regulatory models W50, W55 User’s Guidep.1Battery Safety Informationp.2UL, CULp.2EMC: EN 55022p.2EN 55024p.2Trademarksp.2EN 61000-3-2p.2EN 61000-3-3p.2Projector components and features: frontp.6Projector components and features: backp.6Product specificationsp.6Online Registrationp.6Introductionp.6Included Itemsp.6RS232p.7USB BNCp.7(IR)p.7Connector Panelp.7Positioning the projectorp.8Required computer connectionsp.9Connecting a computerp.9Optional computer connectionsp.9Displaying a computer imagep.11Adjusting the imagep.12Connecting a video devicep.13Standard video connectionsp.13Optional video connectionsp.13Displaying a video imagep.14Table 1: Status indicator light behavior and meaningp.16Shutting down the projectorp.16Troubleshooting your setupp.16A Ap.18A Bp.19A B A Bp.19COLORp.20Still having problems?p.22Using the keypad buttonsp.23Troubleshooting the remotep.24Using the remote controlp.24Connecting external speakersp.25Using the audiop.25Troubleshooting audiop.25Presentation featuresp.26Optimizing computer imagesp.26Customizing the projectorp.27Optimizing video imagesp.27Using the menusp.28Picture menup.29Advanced settingsp.30Settings menup.32Replacing the clock batteriesp.36Cleaning the lensp.36Maintenancep.36Replacing the projection lampp.37WARNINGS :p.37Cleaning the dust filterp.39Using the security lockp.39Optional lensesp.40Projected image sizep.40Appendixp.40Read Command Examplesp.43RS-232 Port Settingsp.43Communication Configurationp.43RS-232 commandsp.43Command Formatp.43mand Min Max Default Stp.44Function Com-p.44Write Command Examplesp.44Error Conditionsp.44Limitationsp.44
Page 1 of the InFocus W50 user manual — IN 5102 /IN 5104 /IN 5106
Page 1 · click to enlarge
Page 1
InFocus W50 — IN 5102 /IN 5104 /IN 5106 diagram (page 1)
Fig. 1

IN 5102 /IN 5104 /IN 5106

Regulatory models W50, W55 User’s Guide

Page 2 of the InFocus W50 user manual — EN 61000-3-2
Page 2 · click to enlarge
Page 2

This is a Class A product. In a domestic environment it may cause radio interference,

in which case the user may be required to take adequate measures. The typical use is

Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote

control complies with applicable requirements of 21 CFR 1040.10 and 1040.11. Remote

Changes or modifications not expressly approved by InFocus Corporation may void

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Other specific Country Approvals may apply, see please product certification label.

Operation is subject to the following two conditions: (1) This device may not cause

InFocus reserves the right to alter product offerings and specifications at any time

harmful interference, and (2) this device must accept any interferences received,

control complies with applicable requirements of EN 60825: 1994+A11+A2.

incorrect type of battery. See page 35 for battery replacement instructions.

This document applies to model W50: IN5106, C500, IN5102, C447.

This Class A digital apparatus complies with Canadian ICES-003.

including interference that may cause undesired operation.

Input ratings100-120/220-240Vac, 5.0/2.1A, 50/60Hz

in a conference room, meeting room or auditorium.

authority to operate the equipment.

Battery Safety Information

without notice.

UL, CUL

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple

registered trademarks or trademarks of InFocus Corporation in the United States and

We declare under our sole responsibility that this projector conform to the following

Computer, Inc. IBM is a trademark or registered trademark of International Business

radiate radio frequency energy and, if not installed and used in accordance with the

interference in which case the user will be required to correct the interference at his

ManufacturerInFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon

Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered

registered trademarks of Adobe Systems Incorporated. HDMI, the HDMI logo and

High-Definition Multimedia Interface are trademarks or registered trademarks of

This equipment has been tested and found to comply with the limits for a Class A

provide reasonable protection against harmful interference when the equipment is

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

operated in a commercial environment. This equipment generates, uses, and can

instruction manual, may cause harmful interference to radio communications.

97070 USA European OfficeLouis Armstrongweg 110, 1311 RL Almere, The Netherlands

trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or

HDMI Licensing LLC. InFocus, In Focus, and INFOCUS (stylized) are either

Operation of this equipment in a residential area is likely to cause harmful

own expense. This device complies with part 15 of the FCC Rules.

Low Voltage Directive 2006/95/EC

SafetyIEC 60950-1: 1 st Edition

directives and norms:

EMC: EN 55022

EN 55024

Trademarks

other countries.

EN 61000-3-2

EN 61000-3-3

Show 7 more labels / short text on this page
Remote Control Warning · EN 55022 Warning · Agency Approvals · Canada · Declaration of Conformity · EMC Directive 2004/108/EC · FCC Warning
Page 3 of the InFocus W50 user manual — Battery Safety Information
Page 3 · click to enlarge
Page 3
InFocus W50 — Battery Safety Information diagram (page 3)
Fig. 2 · Battery Safety Information
InFocus W50 — Battery Safety Information diagram (page 3)
Fig. 3 · Battery Safety Information

Do not look into laser beam emitted from the front of the remote control

Do not look into laser beam emitted from the front of the remote control

InFocus W50 — Battery Safety Information diagram (page 3)
Fig. 4 · Battery Safety Information
InFocus W50 — Battery Safety Information diagram (page 3)
Fig. 5 · Battery Safety Information

OR this label · OR this label

Page 4 of the InFocus W50 user manual — Battery Safety Information
Page 4 · click to enlarge
Page 4

For complete details on connecting and operating the projector, refer to this

User’s Guide. Electronic versions of this User’s Guide in multiple languages

The website also has technical specifications (an interactive image size cal-

product data sheet), a web store to buy accessories, and a page for online

culator, laptop activation commands, connector pin outs, a glossary, the

registration. See the inside of the back cover for a list of all relevant web

are available on our website.

addresses.

Introduction 5 Included Items 5 Positioning the projector 7 Connecting a computer 8 Required computer connections 8 Displaying a computer image 10 Adjusting the image 11 Connecting a video device 12 Displaying a video image 13 Shutting down the projector 15 Troubleshooting your setup 15

Using the keypad buttons 22 Using the remote control 23 Using the audio 24

Optimizing computer images 25 Presentation features 25 Optimizing video images 26 Customizing the projector 26

Using the menus 27 Picture menu 28 Settings menu 31

Maintenance 35 Cleaning the lens 35 Replacing the clock batteries 35 Replacing the projection lamp 36 Cleaning the dust filter 38 Using the security lock 38

Appendix 39 Projected image size 39 RS-232 commands 42

Table of Contents

Page 5 of the InFocus W50 user manual — Battery Safety Information
Page 5 · click to enlarge
Page 5

3’ / 1 m

Follow these instructions to help ensure image quality and lamp life over

the life of the projector. Failure to follow these instructions may affect the

warranty. For complete details of the warranty, see the Warranty booklet.

2’ / 0.6 m

5’ / 1.5 m

8’ / 2.4 m

  • Place the projector in a horizontal position no greater than 8 degrees off
  • Locate the projector at least 4' (1.2 m) away from any heating or cooling
  • Only genuine InFocus lamps are tested for use in this projector. InFocus

and drinks out of the "keep out" area under and around the projector, as

  • Locate the projector in a well-ventilated area without any obstructions

to intake or exhaust vents. Do not place the projector on a tablecloth or

wear protective eyewear before opening lamp door. A warning sticker

is included with the user documentation. Place this sticker on the lamp

  • Hg – Lamp contains mercury. Manage in accordance with local
  • In the unlikely event of a lamp rupture, particles may exit through the
  • Use only the power cord provided. A surge-protected power strip is
  • Warning : To prevent eye injury if the projector is ceiling mounted,

is not liable for the performance, safety or certification of any other

projector vents. When the projector is turned on, keep people, food,

lamps. The use of other lamps violates the projector warranty and

  • Refer to this manual for proper startup and shutdown procedures.

door if the projector is mounted on the ceiling.

disposal laws. See www.lamprecycle.org.

other soft covering that may block the vents.

voids all certification marks on this projector.

  • Use only approved ceiling mounts.

indicated by the "X" areas.

recommended.

vents.

axis.

Page 6 of the InFocus W50 user manual — Product specifications
Page 6 · click to enlarge
Page 6
InFocus W50 — Projector components and features: front diagram (page 6)
Fig. 6 · Projector components and features: front
InFocus W50 — Projector components and features: front diagram (page 6)
Fig. 7 · Projector components and features: front

Projector components and features: front

Projector components and features: back

power switch power plug

Your new multimedia projector provides three computer, three video, and

has XGA 1024x768 resolution. Optional user-changeable short, fixed short,

many different uses. The projector is easy to connect, easy to use, and easy

four audio inputs, one audio output, and RS-232 and Network control. It

long and ultra long throw lenses make this a flexible product suitable for

announcements, and registration incentives. See the inside back cover for

To read the latest specifications on your multimedia projector, be sure to

visit our website. Web address information is located on the back inside

Register your projector on our website to receive product updates,

*the lens cap tether can attach the lens cap to the projector if desired.

cover of this User’s Guide.

Product specifications

Online Registration

Introduction

Included Items

the web address.

to maintain.

Show 15 more labels / short text on this page
receiver · air intake · remote · control · lamp door · leveling foot · zoom/focus/offset door · connectors · VESA computer cable · A/V cable · projector · remote · documentation · power cable · lens cap*
Page 7 of the InFocus W50 user manual — Connector Panel
Page 7 · click to enlarge
Page 7

power connector and switch

RS232

USB BNC

(IR)

are available in the Appendix and on our website. See the back inside cover

must have a 1.3-compatible source. The HDMI, because it is a digital signal,

The projector provides three computer and three video connection options:

The projector provides computer and video connectors for audio support:

new projector ships standard with decryption codes so you can enjoy these

The RS-232 Command Line Interface (CLI) specifications and commands

* HDMI is an industry standard, uncompressed, all-digital audio/video interface that connects between sources, such as set-top boxes, DVD play-

ers, and receivers and your projector. To take advantage of HDMI 1.3 you

encrypted with HDCP (high-bandwidth digital-content protection). Your

yields the highest quality image. It is common for these signals to be

  • one HDMI™ (High Definition Multimedia Interface)*
  • one component BNC (G/Y, B/C B /P B , R/C R /P R , H, V)

The projector also provides the following connectors:

  • RS-232 serial connector (for serial control)
  • RJ-45 connector (for networked control)

of this User’s Guide for website information.

  • two composite RCA stereo audio (L, R)
  • one component RCA video (Pr, Pb, Y)
  • one composite RCA video

high quality, all digital images.

  • one VESA computer
  • one wired remote

Connector Panel

  • one monitor out
  • one audio out
  • two audio ins
  • one S-video
Show 16 more labels / short text on this page
serial control · lock HDMI monitor · wired remote · (audio out) · external · speakers · component video · RJ-45 VESA computer · audio in 3,4 · s-video composite · video · audio in 1,2 · remote · control · receiver · speaker
Page 8 of the InFocus W50 user manual — Positioning the projector
Page 8 · click to enlarge
Page 8

Projection angle in 4:3 mode (default)

9:1 1:1

10 ft high image

9:1 bottom of image

1:1 bottom of image

10% below lens center

50% below lens center

To determine where to position the projector, consider the size and shape of

  • Position the projector on a flat surface at a right angle to the screen. The

projector (with the standard lens) must be at least 3 feet (0.9m) from the

sion cables). To ensure adequate cable access, do not place the projector

  • Position the projector the desired distance from the screen. The distance

video format determine the size of the projected image. For information

  • For the standard lens that comes with the projector, the image exits at a

the projector and the rest of your equipment. Here are some general guide-

  • If you are installing the projector on the ceiling, refer to the installation

guide that comes with the Ceiling Mount Kit for more information. To

about image sizes at different distances, see “Projected image size” on

variable. The image offset is 90% at a 9:1 ratio when the projector is in

  • The image offset is 50% when the lens shift is at a 1:1 ratio. This means
  • For information about the optional lenses image offsets, see “Projected

your screen, the location of your power outlets, and the distance between

within 6 feet (1.8m) of your video device (unless you purchase exten-

mends using an authorized ceiling mount. The Ceiling Mount Kit is

from the lens of the projector to the screen, the zoom setting, and the

4:3 mode (default mode). This means that if you have an image 10’ high, the bottom of the image will be 1’ below the center of the lens.

that if you have an image 10’ high, the bottom of the image will be 5’

  • Position the projector within 10 feet (3m) of your power source and

given angle. However, the lens shift feature makes the image offset

turn the image upside down, see “Ceiling” on page 31. We recom-

sold separately; visit our website for more information.

within 6 inches (.15m) of a wall or other object.

Positioning the projector

below the center of the lens.

image size” on page 39.

projection screen.

page 39.

lines:

lens center

Page 9 of the InFocus W50 user manual — Optional computer connections
Page 9 · click to enlarge
Page 9
InFocus W50 — Required computer connections diagram (page 9)
Fig. 8 · Required computer connections

connect BNC cable connect HDMI cable

Connect one end of the VESA computer cable to the Computer 2 connector

You can also connect to your computer using optional BNC or HDMI cables.

puter 3 connectors on the projector. Connect the other end to the video port

To have sound with your presentation, connect the audio cable to your com-

puter and to the corresponding computer Audio In connector on the projec-

tor. You can assign a particular source to a particular audio in connector, see

on the projector. Connect the other end to the video port on your computer.

If you are using a desktop computer, you first need to disconnect the moni-

Connect the black power cable to the connector on the back of the projector

on your computer. If you are using a desktop computer, you first need to

Connect the BNC connectors on the BNC cable to the appropriate Com-

disconnect the monitor cable from the computer’s video port.

Or, connect the HDMI cable to the Computer 1 connector.

Required computer connections

tor cable from the computer’s video port.

Connecting a computer

Optional computer connections

and to your electrical outlet.

page 31.

connect computer cable · connect power cable · connect audio cable

Page 10 of the InFocus W50 user manual — Required computer connections
Page 10 · click to enlarge
Page 10
InFocus W50 — Required computer connections diagram (page 10)
Fig. 9 · Required computer connections

The projector can be managed by networking software through its Network

computer screen as well as on the projection screen, plug the monitor cable

other control device or computer by connecting an RS-232 cable to the pro-

jector’s Serial Control connector. Specific RS-232 commands can be found

(RJ-45) connector. Detailed instructions on this feature can be found on our

You can control the projector from an LCD control panel, touch screen, or

If you are using a desktop computer and want to see the image on your

in the Service and Support section of our website and in the Appendix.

to the Monitor out connector on the projector.

website.

Show 4 more labels / short text on this page
Network · connect monitor cable · connect RS-232 cable · connect CAT-5 cable
Page 11 of the InFocus W50 user manual — Displaying a computer image
Page 11 · click to enlarge
Page 11
InFocus W50 — Displaying a computer image diagram (page 11)
Fig. 10 · Displaying a computer image
InFocus W50 — Displaying a computer image diagram (page 11)
Fig. 11 · Displaying a computer image

press Power button press Power switch

activate laptop’s external port

O

comes on, the startup screen is displayed and the light is steady green. It can

Many laptops do not automatically turn on their external video port when a

The computer’s image should appear on the projection screen. If it doesn’t,

turn the external display on and off. Refer to your computer’s documenta-

Press the power switch on the back of the projector to the on (I) position.

projector is connected. Usually a key combination like FN + F5 is used to

The Power light blinks green and the fans start to run. When the lamp

The Power light on the Status Indicator Panel (page 15) lights green.

Press the Power button on the top of the projector or the remote.

take a minute for the image to achieve full brightness.

Make sure your laptop’s external video port is active.

Displaying a computer image

press the Source button on the keypad or remote.

? No computer image? Get help on page 16.

? No startup screen? Get help on page 16.

tion to learn your computer’s key combination.

Turn on your computer.

Remove the lens cap.

turn on computer · remove lens cap

Page 12 of the InFocus W50 user manual — Adjusting the image
Page 12 · click to enlarge
Page 12
InFocus W50 — Adjusting the image diagram (page 12)
Fig. 12 · Adjusting the image

adjust zoom and focus

If the image is not on the screen or viewing area, adjust it by using the lens

Adjust the height of the projector, if necessary, by pressing the release but-

Position the projector the desired distance from the screen at a 90 degree

Adjust the zoom or focus by rotating the Zoom or Focus rings inside the

Use the right dial to shift the lens left or right. Use the left dial to shift the

tons on each side of the projector’s front to extend the elevator feet.

lens door until the desired image size and focus are produced.

See page 39 for a table listing screen sizes and distances.

Adjust the Contrast or Brightness in the Picture menu.

See page 27 for help with the menus.

angle (perpendicular) to the screen.

shift dials inside the lens door.

Adjusting the image

lens up or down.

Show 9 more labels / short text on this page
foot elevator · foot · button release · button · release · elevator · adjust lens shift · adjust distance · adjust height
Page 13 of the InFocus W50 user manual — Standard video connections
Page 13 · click to enlarge
Page 13
InFocus W50 — Connecting a video device diagram (page 13)
Fig. 13 · Connecting a video device

connect S-video and video cables

low Video 3 connector on the projector. Plug a white connector into the left

device and into the Video 2 connector on the projector. Use the A/V cable’s

If the video device uses component cable connectors (sold separately), plug

the cable’s green connectors into the green component-out connector on the

video device and into the Video 1 green component connector (labeled “Y”)

component-out connector on the video device and into the blue component

connector on the video device. Plug the other yellow connector into the yel-

audio out connector on the video device and plug a red connector into the

connector into a right audio in connector on the projector. You can assign a

Connect the black power cable to the connector on the back of the projector

audio connectors as described directly above (the yellow connectors on the

on the projector. Plug the component cable’s blue connectors into the blue

nectors on the A/V cable are not used). NOTE: The component connectors

right audio out connector on the video device. Plug the remaining white

connector into a left audio in connector on the projector, and plug the red

connector (labeled “Cb/Pb”) on the projector. Plug the component cable’s

red connectors into the red component-out connector on the video device

and into the red component connector (labeled “Cr/Pr”) on the projector.

Use the A/V cable’s audio connectors as described above (the yellow con-

Plug the audio/video (A/V) cable’s yellow connector into the video-out

If the video device uses a round, four-prong S-video connector, plug an

can be used for HDTV sources (480i, 480p, 720p, 576i and 1080i formats).

S-video cable (sold separately) into the S-video connector on the video

particular source to a particular audio in connector, see page 31.

Connecting a video device

Standard video connections

Optional video connections

and to your electrical outlet.

A/V cable are not used).

Show 4 more labels / short text on this page
connect component cables · connect power cable · connect A/V cable · and video cables
Page 14 of the InFocus W50 user manual — Displaying a video image
Page 14 · click to enlarge
Page 14
InFocus W50 — Displaying a video image diagram (page 14)
Fig. 14 · Displaying a video image

press Power button press Power switch

turn on video device

O

comes on, the startup screen is displayed and the light is steady green. It can

tons on each side of the projector’s front to extend the elevator feet. Rotate

angle to the screen. See page 39 for a table listing screen sizes and distances

Press the power switch on the back of the projector to the on (I) position.

Adjust the height of the projector, if necessary, by pressing the release but-

Position the projector the desired distance from the screen at a 90 degree

The Power light blinks green and the fans start to run. When the lamp

The video device’s image should appear on the projection screen. If it

The Power light on the Status Indicator Panel (page 15) lights green.

Press the Power button on the top of the projector or the remote.

doesn’t, press the Source button on the keypad or remote.

take a minute for the image to achieve full brightness.

? No startup screen? Get help on page 16.

the feet, if necessary, to level the projector.

Displaying a video image

Plug in and turn on the video device.

Remove the lens cap.

to the screen.

Show 4 more labels / short text on this page
button · remove lens cap · adjust distance · adjust height
Page 15 of the InFocus W50 user manual — Displaying a video image
Page 15 · click to enlarge
Page 15
InFocus W50 — Displaying a video image diagram (page 15)
Fig. 15 · Displaying a video image
InFocus W50 — Displaying a video image diagram (page 15)
Fig. 16 · Displaying a video image

adjust Zoom and Focus

If the image is not on the screen or viewing area, adjust it by using the lens

Adjust the zoom or focus by rotating the Zoom or Focus rings inside the

Use the right dial to shift the lens left or right. Use the left dial to shift the

Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.

lens door until the desired image size and focus are produced.

Adjust the volume in the Audio menu.

See page 27 for help with the menus.

shift dials inside the lens door.

lens up or down.

adjust Picture menu · adjust Lens Shift · adjust volume

Page 16 of the InFocus W50 user manual — Shutting down the projector
Page 16 · click to enlarge
Page 16

The Status Indicator Panel on top of the projector indicates the state of the

then turn the projector on again. Contact

If the lamp light turns on again, replace the

Power, solid green The power button has been pressed and

the software has initialized or the projec-

Power, blinking green The power button has been pressed and

the software is initializing, or the projec-

Thermometer The projector is too hot. Make sure the

vents aren’t blocked (see page 20). Turn

Technical Support if the problem persists.

minute, then turn the projector on again.

minute, then turn the projector on again.

If the service lamp turns on again, service

is required. Visit our website to contact

tor is powering down and the fans are

off the projector and wait one minute,

Lamp Turn off the projector and wait one

Table 1: Status indicator light behavior and meaning

Wrench/Service Turn off the projector and wait one

lamp and reset the lamp timer.

tor has been powered off.

running to cool the lamp.

Status Indicator Panel icons Meaning

Service.

projector and can help you troubleshoot.

To turn off the projector, press the power button and verify that you want to

time. The lamp turns off and the Power light blinks green for over 1 minute

detected for 5 minutes. This blank screen helps preserve the life of the pro-

passed. When Power Save is enabled, Screen Save is disabled. See page 32.

turn the projector off by pressing the power button again within 3 seconds.

while the fans continue to run to cool the lamp. When the lamp has cooled,

the Power light is solid green and the fans stop. Press the power switch on

the back of the projector and unplug the power cable to completely power

If your image appears correctly on the screen, skip to the next section. If it

jector. The image returns when an active source is detected or a remote or

You can cancel the shutdown by not pressing the power button a second

You can make the blank screen appear after five minutes by turning on

The projector also has a Power Save feature that automatically turns the

lamp off after no signals are detected for 20 minutes. After 10 additional

minutes with no signal, the projector powers down. If an active signal is

received before the projector powers down, the image is displayed. You

must press the Power button to display an image after 30 minutes have

The projector automatically blanks the screen after no active source is

Screen Save in the Settings>System menu. See page 32.

Shutting down the projector

Troubleshooting your setup

does not, troubleshoot the setup.

Turning off the projector

keypad button is pressed.

off the projector.

Screen Save · Power Save

Page 17 of the InFocus W50 user manual — A
Page 17 · click to enlarge
Page 17
InFocus W50 — Table 1: Status indicator light behavior and meaning diagram (page 17)
Fig. 17 · Table 1: Status indicator light behavior and meaning

No startup screen Plug power cable in, press power switch and

A

Page 18 of the InFocus W50 user manual — A
Page 18 · click to enlarge
Page 18
InFocus W50 — A A diagram (page 18)
Fig. 18

Image fuzzy or cropped Set your computer’s display resolution to

range” Adjust computer refresh rate in Control

No computer image, just the words “Signal out of

A A

A

Show 10 more labels / short text on this page
select1024x768) · or turn-on dual- · disable laptop · or cropped” · For a laptop, · display mode · monitor · system) · Signal out of · range
Page 19 of the InFocus W50 user manual — A B A B
Page 19 · click to enlarge
Page 19

A B

Image not square Adjust keystone the Picture menu Square image

Picture>Advanced menu Correct image

Picture>Aspect ratio menu Correct image

Image not sharp Adjust the focus ring or Sharpness in the

InFocus W50 — A B diagram (page 19)
Fig. 19
InFocus W50 — A B diagram (page 19)
Fig. 20
InFocus W50 — A B diagram (page 19)
Fig. 21

Image does not fit 16:9 screen Change aspect ratio to 16:9 in

A B A B

Problem Solution Result · Projector troubleshooting

Page 20 of the InFocus W50 user manual — COLOR
Page 20 · click to enlarge
Page 20

COLOR

A B

A B

Image reversed left to right Turn on/off Rear in Settings>System menu Correct image

brightness, contrast in the menus Correct image

Turn on/off Ceiling in Settings>System

InFocus W50 — COLOR diagram (page 20)
Fig. 22

Projected colors don’t match source Adjust color, tint, color temperature,

InFocus W50 — COLOR diagram (page 20)
Fig. 23

COLOR

A B

A

menu Correct image · Image upside down

Page 21 of the InFocus W50 user manual — COLOR
Page 21 · click to enlarge
Page 21

projector to cool for one minute Unplug projector; wait 20 minutes; plug in

InFocus W50 — COLOR diagram (page 21)
Fig. 24
InFocus W50 — COLOR diagram (page 21)
Fig. 25
projector and turn it onlamp lights

Lamp won’t turn on, Lamp light is lit (page 15) Lamp may need to be replaced (page 36) Lamp turns on

Lamp won’t turn on, Temp light is lit (page 15) Make sure vents aren’t blocked; allow

InFocus W50 — COLOR diagram (page 21)
Fig. 26
InFocus W50 — COLOR diagram (page 21)
Fig. 27

Temperature light · Lamp light

Page 22 of the InFocus W50 user manual — Still having problems?
Page 22 · click to enlarge
Page 22

This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we

recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its

InFocus W50 — Still having problems? diagram (page 22)
Fig. 28 · Still having problems?

If you need assistance, visit our website or call us. See the inside of the back cover for a list of all relevant web addresses.

InFocus W50 — Still having problems? diagram (page 22)
Fig. 29 · Still having problems?

Image not centered on screen Move projector, adjust zoom or lens shift,

Still having problems?

full value.

Correct image

Page 23 of the InFocus W50 user manual — Using the keypad buttons
Page 23 · click to enlarge
Page 23

up/down arrows–navigates to and adjusts settings in the menus (page 27).

power–turns the projector on (page 10) and off (page 15).

select–confirms choices made in the menus (page 27).

menu–opens the on-screen menus (page 27).

Using the keypad buttons

source–switches among active sources

Page 24 of the InFocus W50 user manual — Using the remote control
Page 24 · click to enlarge
Page 24
InFocus W50 — Troubleshooting the remote diagram (page 24)
Fig. 30 · Troubleshooting the remote
  • Make sure the batteries are installed in the proper orientation and are

not dead. The LED at the top of the remote lights when any button is

  • Make sure you’re pointing the remote at the projector, not the com-

puter, and are within the remote range of 16 feet (5m).

pressed when the battery power is adequate.

Troubleshooting the remote

The remote uses two (2) provided AAA batteries (Hitachi Maxell, part num-

at the computer). The range of optimum operation is about 16 feet (5m).For

To use the laser pointer, press and hold the Laser button. The laser turns off

The remote also has a power button to turn the projector on and off, volume

the remote's buttons in the dark, and a video and computer button to switch

to display a blank screen instead of the current slide; use the effect button to

back, aligning the + and - ends of the batteries, sliding them into place, and

To operate, point the remote at the projection screen or at the projector (not

The remote contains four Source buttons that allow you to assign a particu-

lar input to a specific source. Simply press the numbered Source buttons to

the arrow buttons to navigate, and the Select button to select features and

buttons and a mute button to control the sound, a backlight button to light

Two presentation-specific features are also provided. Use the blank button

The Auto Image button reacquires the computer image and the Presets but-

when the button is released, or times out after two (2) minutes of continu-

Press the remote's Menu button to open the projector's menu system. Use

ton lets you customize the settings for each source. Up to three Preset set-

ber LR03). They are easily installed by sliding the cover off the remote's

invoke a user-definable action, such as freeze, PiP, or magnify.

travel to whatever four sources you wish to have available.

best results, aim the remote directly at the projector.

Using the remote control

tings can be customized and saved.

adjust values in the menus.

between those two sources.

then replacing the cover.

ous operation.

remote control.

navigation buttons · source buttons

Page 25 of the InFocus W50 user manual — Troubleshooting audio
Page 25 · click to enlarge
Page 25
InFocus W50 — Connecting external speakers diagram (page 25)
Fig. 31 · Connecting external speakers

To adjust the volume, mute, or loudness, use the Audio menu (see page 31).

source. By default, Audio 1 corresponds to Computer 2, Audio 2 cor-

responds to Computer 3, Audio 3 corresponds to Video 2 and 3, and

To play sound from the projector, connect your source to an Audio In con-

  • Make sure you are connected to the corresponding audio in for your

Audio 4 corresponds to Video 1. You can change these assignments,

power source by plugging a speaker cable into the projector’s Audio Out

The projector can be attached to external speakers that have their own

  • If playing a video, make sure the playback has not been paused.
  • Make sure the volume is turned up enough.
  • Make sure the audio cable is connected.

If there is no sound, check the following:

Connecting external speakers

  • Make sure mute isn’t active.
  • Adjust the audio source.

Using the audio

Troubleshooting audio

nector on the projector.

see page 31.

connector.

Show 5 more labels / short text on this page
connect audio cable · adjust volume · external speakers · speaker · cable
Page 26 of the InFocus W50 user manual — Optimizing computer images
Page 26 · click to enlarge
Page 26

Auto Image, Freeze, Magnify, Source Info, and Service Info. See page 33

screen to a black, white, blue, or a custom logo screen via Capture New.

matically shut down the projector after several minutes of inactivity or

Info. You can select from Blank, Mute, AV Mute, Aspect Ratio, Source,

  • The Freeze effect allows you to freeze the displayed image. This is use-

ful if you want to make changes on your computer without your audi-

  • Two menu options, Power Save and Screen Save, are provided to auto-

Several features are provided to make giving presentation easier. The fol-

  • The Custom key, available on several optional remotes only, allows

you to assign various features to the key. The default effect is Source

  • A Low Power menu option is also available to help lower the projec-

lowing is an overview, details are found in the menu section on page 27.

  • The Startup Logo menu option lets you change the default startup

display a blank screen. This helps preserve lamp life. See page 32.

tor’s fan sound volume. See page 31.

Presentation features

ence seeing them.

See page 32.

for details.

  • Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to

and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your

After your computer is connected properly and the computer’s image is on

the screen, you can optimize the image using the onscreen menus. For gen-

image height. TV screens are usually 1.33:1, also known as 4:3. HDTV

save the settings using Presets. This allows you to quickly recall these

  • Once you have optimized the image for a particular source, you can
  • Adjust the Phase, Tracking, or Horizontal or Vertical position in the
  • Adjust the Keystone, Contrast, or Brightness in the Picture menu.
  • Adjust the Color Temperature in the Advanced menu.

eral information on using the menus, see page 27.

Optimizing computer images

input source. See page 28 for details.

settings later. See page 29.

Advanced menu.

Page 27 of the InFocus W50 user manual — Optimizing video images
Page 27 · click to enlarge
Page 27
  • Control your projector using RS232 commands. See page 9 and page 42.
  • For rear projection, turn Rear mode on in the Settings>System menu.
  • Specify which source the projector checks first for an active signal dur-
  • Customize the projector for your specific installation using optional

long or short throw lenses. See the inside back cover of this User’s

You can customize the projector for your specific setup and needs. See

  • For ceiling mounted projection, turn Ceiling mode on in the Set-
  • Turn the projector’s on-screen display messages on and off.
  • Specify blank screen colors and startup logos.

page 31 to page 34 for details on these features.

Customizing the projector

  • Turn on power saving features.

Guide for ordering information.

  • Specify the menu language.

tings>System menu.

ing power-up.

After the video device is connected properly and the image is on the screen,

and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your

you can optimize the image using the onscreen menus. For general informa-

  • Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
  • Change the Aspect ratio. Aspect ratio is the ratio of the image width to

image height. TV screens are usually 1.33:1, also known as 4:3. HDTV

  • Adjust the Color Temperature. Select a listed value, or select User and

individually adjust the intensity of the red, green, and blue color. See

  • Select a Sharpness setting. See page 29.

Optimizing video images

tion on using the menus, see page 27.

input source. See page 28.

menu. See page 28.

page 29.

Page 28 of the InFocus W50 user manual — Using the menus
Page 28 · click to enlarge
Page 28
InFocus W50 — Using the menus diagram (page 28)
Fig. 32 · Using the menus
InFocus W50 — Using the menus diagram (page 28)
Fig. 33 · Using the menus
InFocus W50 — Using the menus diagram (page 28)
Fig. 34 · Using the menus

tons, or turn the feature on or off using check boxes. Press Select to confirm

Dots appear before the menu name. The number of dots indicate the menu’s

den when a computer source is active. Other menu items may be grayed out

menus automatically close after 60 seconds if no buttons are pressed.) The

Main menu appears. Use the arrow buttons to move up and down to high-

adjustments are complete, navigate to Previous, then press Select to go to

the previous menu; press the Menu button at any time to close the menus.

nected. For example, Tint is only available for video sources and will be hid-

when they are not available. For example, Brightness is grayed out until an

To open the menus, press the menu button on the keypad or remote. (The

down arrow buttons to adjust the value, select an option using radio but-

level, ranging from one (the Main menu) to five (the most nested menus).

To change a menu setting, highlight it, press Select, then use the up and

your changes. Use the arrows to navigate to another setting. When your

  • The Source Info menu provides a read-only display of information
  • The Settings menu provides set-up type adjustments that are not

Certain menu items may be grayed out until a particular source is con-

light the desired submenu, then press the Select button.

  • The Picture menu provides image adjustments.

about the projector and source.

The menus are grouped by usage:

Using the menus

changed often.

image is active.

Show 9 more labels / short text on this page
Picture Settings · Keypad navigation · menu · buttons Main menu · Dots · Menu · button · Source Info menu · menu
Page 29 of the InFocus W50 user manual — Picture menu
Page 29 · click to enlarge
Page 29
InFocus W50 — Picture menu diagram (page 29)
Fig. 35 · Picture menu
InFocus W50 — Picture menu diagram (page 29)
Fig. 36 · Picture menu
Contrastcontrols the degree of difference between the lightest and darkest

TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are

To adjust the following six settings, highlight the setting, press Select, use

Keystone Verticaladjusts the image vertically and makes a squarer image
Keystone Horizontaladjusts the image horizontally and makes a squarer

Aspect Ratio: Aspect ratio is the ratio of the image width to image height.

the up and down arrows to adjust the values, then press select to confirm

Color(Computer 1 and video sources only) adjusts a video image from
Tint(Computer 1 and NTSC video sources only) adjusts the red-green

1.78:1, or 16:9. The default is 4:3, which displays the input resized up or down to fill the display area.

parts of the picture and changes the amount of black and white in the

Auto Image: resynchs the projector to the source.

Brightness: changes the intensity of the image.

image by using an adjustable scale band.

black and white to fully saturated color.

by using an adjustable scale band.

color balance in the image.

Picture menu

the changes.

image.

Show 5 more labels / short text on this page
decreasing keystone · increasing keystone · Keystone Horizontal · Keystone Vertical · Aspect Ratio
Page 30 of the InFocus W50 user manual — Advanced settings
Page 30 · click to enlarge
Page 30
InFocus W50 — Advanced settings diagram (page 30)
Fig. 37 · Advanced settings
InFocus W50 — Advanced settings diagram (page 30)
Fig. 38 · Advanced settings
InFocus W50 — Advanced settings diagram (page 30)
Fig. 39 · Advanced settings
InFocus W50 — Advanced settings diagram (page 30)
Fig. 40 · Advanced settings
InFocus W50 — Advanced settings diagram (page 30)
Fig. 41 · Advanced settings
InFocus W50 — Advanced settings diagram (page 30)
Fig. 42 · Advanced settings

User Presets 1 (or 2 or 3). You can recall these settings in the future by select-

sources (except 480i/576i). It allows you to select a color space that has been

There are also user-definable presets. To set a preset for the current source,

adjust the image, select Save Settings in the Presets menu, then select Save

image, Presets Off will automatically be selected in the Preset menu to indi-

Sharpnesschanges the clarity of the edges of a video image. Select a sharp-

specifically tuned for the input signal. When Auto is selected, the projector

value, or select User and individually adjust the intensity of the red, green,

computer presentations and video images in different lighting conditions

automatically determines the standard. To choose a different setting, turn

PresetsPresets are provided that optimize the projector for displaying

off Auto, then choose RGB for computer sources, RGB Video for HDMI

ing the User 1 preset. If you select User Presets then further adjust the

To restore the factory default settings, choose Factory Reset in the Set-

computer sources, and either REC709 or REC601 for component video

Color Temperaturechanges the intensity of the colors. Select a listed
Color SpaceThis option applies to computer and component video

and on different backgrounds.

cate changes have been made.

tings>Service menu.

Advanced settings

and blue colors.

ness setting.

sources.

Show 5 more labels / short text on this page
Color Temperature · Save Settings · Sharpness · Presets · Color Space
Page 31 of the InFocus W50 user manual — Advanced settings
Page 31 · click to enlarge
Page 31
InFocus W50 — Advanced settings diagram (page 31)
Fig. 43 · Advanced settings
InFocus W50 — Advanced settings diagram (page 31)
Fig. 44 · Advanced settings

Computer 2 Computer 3

InFocus W50 — Advanced settings diagram (page 31)
Fig. 45 · Advanced settings
InFocus W50 — Advanced settings diagram (page 31)
Fig. 46 · Advanced settings
Phaseadjusts the horizontal phase of computer 2, 3 and component (except
Video Standardwhen set to Auto, the projector attempts to automatically

standard options may vary depending on your region of the world.) If the

Active Iriswhen on, the projector monitors the image brightness and mod-

Presentation mode, it looks at peak brightness, in Theater mode it looks at

Overscan(Computer 1 and video sources only) removes noise around the

projector is unable to detect the correct standard, the colors may not look

video standard by selecting NTSC, PAL, or SECAM from the Video Stan-

ifies the light output if the image is dark, which improves black levels. In

Horizontal / Vertical Positionadjusts the position of a computer source

pick the video standard based on the input signal it receives. (The video

right or the image may appear “torn.” If this happens, manually select a

Trackingadjusts the horizontal scan of a computer source (except Com-

Computer 2: allows you to turn Sync on Green on for this source.

Computer 3: allows you to turn Sync on Green on for this source.

(except Computer 1) and Video 1 source (except 480i and 576i).

The following 4 options are for computer sources only:

480i and 576i) sources.

average brightness.

video image.

dard menu.

puter 1).

Active Iris · Video Standard

Page 32 of the InFocus W50 user manual — Settings menu
Page 32 · click to enlarge
Page 32
PC Screen Saver Offprevents your notebook computer from going into
InFocus W50 — Settings menu diagram (page 32)
Fig. 47 · Settings menu

Screen Save mode. The projector must be connected to the PC via a USB

InFocus W50 — Settings menu diagram (page 32)
Fig. 48 · Settings menu
InFocus W50 — Settings menu diagram (page 32)
Fig. 49 · Settings menu
InFocus W50 — Settings menu diagram (page 32)
Fig. 50 · Settings menu
InFocus W50 — Settings menu diagram (page 32)
Fig. 51 · Settings menu

cable for this feature to work.

InFocus W50 — Settings menu diagram (page 32)
Fig. 52 · Settings menu

blank screen displays. When Autosource is checked, Powerup Source deter-

wear protective eyewear before opening lamp door. A warning sticker is

Display Messagesdisplays status messages (such as “Searching”) in the

put of the lamp. This also lowers the fan speed, making the projector qui-

present, the projector checks the sources in order until a source is found or

Auto PowerWhen Auto Power is checked, the projector automatically

goes into the startup state after the projector is powered on. This allows

Low Powertoggles between on and off. Turn it on to lower the light out-
Audioallows adjustments to the volume. Also allows you to turn on and

off the Internal speakers and assign a particular source to a specific audio

input. If your HDMI source has problems with its audio stream, you can

when using the remote. Also allows selection of a default Startup Source

defaults to the source selected in Powerup Source. If no source is found, a

Ceiling: turns the image upside down for ceiling-mounted projection.

IR Receiversturns individual IR receivers off or on to avoid environ-
Sourcesallows you to assign a particular input to a specific source key
Sources>Power-up Sourcethis determines which source the projector

mines which source the projector defaults to at power-up. If no signal is

included with the user documentation. Place this sticker on the lamp

Sources>AutosourceWhen Autosource is not checked, the projector
System>Rearreverses the image so you can project from behind a

control of ceiling mounted projectors with a wall power switch.

door if the projector is mounted on the ceiling.

checks first for active signal during power-up.

mute it by selecting HDMI Noise Cancel.

and enables or disables Autosource.

lower-left corner of the screen.

mental interference.

translucent screen.

Settings menu

until power down.

eter.

Show 7 more labels / short text on this page
Sources Powerup · Source · IR Receivers · Audio · Settings · System · menu
Page 33 of the InFocus W50 user manual — Settings menu
Page 33 · click to enlarge
Page 33
InFocus W50 — Settings menu diagram (page 33)
Fig. 53 · Settings menu
InFocus W50 — Settings menu diagram (page 33)
Fig. 54 · Settings menu
InFocus W50 — Settings menu diagram (page 33)
Fig. 55 · Settings menu
InFocus W50 — Settings menu diagram (page 33)
Fig. 56 · Settings menu

detected or a remote or keypad button is pressed. Screen Save is disabled

Startup Logoallows you to display a blank Black, White, or Blue screen

instead of the default screen when no source is detected at startup. It also

To capture a custom logo, display the image you want to capture on your

menu, use the Capture Position X and Capture Position Y adjustments to

detected for 20 minutes. After 10 additional minutes with no signal, the

projector powers down. If an active signal is received before the projec-

frame the logo to be captured. Press Capture Start in the Capture New

menu. The projector will let you know if the capture was a success or a

The next time you start the projector, the custom logo you captured dis-

detected for five minutes. The image returns when an active source is

computer and select the Capture New option. From the Capture New

Blank Screendetermines what color is displayed when you press the
Power Saveautomatically turns the lamp off after no signals are
Screen Saveautomatically blanks the screen after no signals are

allows you to capture and display a custom startup screen.

tor powers down, the image will be displayed.

Blank button on an optional remote.

when Power Save is enabled.

failure.

plays.

Show 4 more labels / short text on this page
Capture New · Screen Save · Blank Screen · Startup Logo
Page 34 of the InFocus W50 user manual — Settings menu
Page 34 · click to enlarge
Page 34
Network RestartDisconnects the projector from the network, gets a

Network Info: Provides information on the network configuration.

InFocus W50 — Settings menu diagram (page 34)
Fig. 57 · Settings menu

new IP address, and reconnects.

InFocus W50 — Settings menu diagram (page 34)
Fig. 58 · Settings menu
InFocus W50 — Settings menu diagram (page 34)
Fig. 59 · Settings menu

Custom Key (for use with optional remote only): allows you to assign a dif-

work connections and TCP/IP protocols. This will allow for the control and

management of the projector over a corporate network. Visit our website for

complete details on using the networking functionality. The following fields

are accessible when DHCP is not checked and available for manual entry of

easily use the effect. Only one effect can be enabled at a time. The default is

DHCPSelect this to automatically obtain an IP address, Subnet mask,

ferent function to the Custom key on the optional remote to quickly and

Source Info; highlight an effect and press Select to choose a different one.

NetworkThe projector has an RJ45 Ethernet connector that supports net-

Subnet Mask: Separates the network address part of the IP address.

Aspect Ratio: sets the ratio of the image width to image height.

Magnify: allows you to enlarge a section of the projected image.

AV Mute: turns off all sound and displays a blank screen.

IP Address: Identifies the projector on the network.

Default Gateway: The IP address of the local router.

DNS Server: Shows the address of the DNS server.

Auto Image: causes all sources to be reacquired.

Source: cycles through the available sources.

Source Info: displays the Source Info menu.

Service Info: displays the Service Info menu.

Freeze: pauses the projected image.

Blank: shows an empty screen.

Mute: turns off all sound.

and Default gateway.

data.

Show 4 more labels / short text on this page
Custom Key · Network · Network · Info
Page 35 of the InFocus W50 user manual — Settings menu
Page 35 · click to enlarge
Page 35
InFocus W50 — Settings menu diagram (page 35)
Fig. 60 · Settings menu

Service menu Lens Type

InFocus W50 — Settings menu diagram (page 35)
Fig. 61 · Settings menu
InFocus W50 — Settings menu diagram (page 35)
Fig. 62 · Settings menu
InFocus W50 — Settings menu diagram (page 35)
Fig. 63 · Settings menu
Reset Lamp Hoursresets the lamp hours counter in the Service Info menu

to zero. Do this only after changing the lamp. It displays a confirmation dia-

your optional lens from the menu. A sticker containing a number between 1

Factory Resetrestores all settings (except Lamp and Filter Hours and Net-

zero. Do this only after cleaning the filter. It displays a confirmation dialog

and 5 is attached to the lens to help you identify which type of lens you pur-

work settings) to their default after displaying a confirmation dialog box.

Lens Typechange this setting only if you purchase an optional lens. The
Reset Filter Hoursresets the filter counter in the Service Info menu to

projector customizes its keystone settings based on the lens used. Select

Languageallows you to select a language for the onscreen display of

Service: to use these features, highlight them and press Select.

Service Code: only used by authorized service personnel.

Service Info: provides information for service.

menus and messages.

log box.

chased.

box.

Language · Service Info

Page 36 of the InFocus W50 user manual — Cleaning the lens
Page 36 · click to enlarge
Page 36
InFocus W50 — Replacing the clock batteries diagram (page 36)
Fig. 64 · Replacing the clock batteries

with a soft dry cloth

The projector has a lithium Hitachi Maxell battery (part number CR2032) on

the bottom that is used to power the clock used for networking applications.

cleaner directly to the lens. Abrasive cleaners, solvents or other harsh

2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.

Visit our website for complete details on using the networking functionality.

3 Turn the projector upside down and use a coin to turn the battery cover to the “Open” position.

4 Remove the battery and dispose of in an environmentally proper man- ner.

Avoid using an excessive amount of cleaner, and don’t apply the

1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

2 Wait 45 minutes to allow the projector to cool thoroughly.

6 Press the battery into place, then replace the battery cover.

1 Turn off the projector and unplug the power cable.

5 Install a new battery with the “+” side facing up.

Replacing the clock batteries

chemicals might scratch the lens.

after replacing the battery.

Cleaning the lens

Maintenance

and non-abrasive · clean the lens · cleaner

Page 37 of the InFocus W50 user manual — WARNINGS :
Page 37 · click to enlarge
Page 37
InFocus W50 — Replacing the projection lamp diagram (page 37)
Fig. 65 · Replacing the projection lamp

the lamp compartment and dispose of cleaning materials. Wash hands

Hg – Lamp contains mercury. Manage in accordance with local

InFocus W50 — Replacing the projection lamp diagram (page 37)
Fig. 66 · Replacing the projection lamp

disposal laws. See www.lamprecycle.org.

turn off and unplug

InFocus W50 — Replacing the projection lamp diagram (page 37)
Fig. 67 · Replacing the projection lamp

after lamp replacement.

  • To avoid burns, allow the projector to cool for at least 45 minutes before
  • Only genuine InFocus lamps are tested with this projector. Use of other

Do not touch the glass lamp screen. Fingerprints can obscure projection

tion when removing the lamp housing. Before replacing the lamp, clean

The lamp hour timer in the Service Info menu counts the number of hours

areas), your retailer or your dealer. Only genuine InFocus lamps are tested

for use in this projector. InFocus is not liable for the performance, safety or

certification of any other lamps. The use of other lamps violates the projec-

3 Loosen the lamp cover screw on the right side of the projector (marked by the arrow) then slide and lift the lamp cover off.

tive eyewear before opening lamp door. A warning sticker is included

with the user documentation. Place this sticker on the lamp door if the

  • Do not drop the lamp module. The glass may shatter and cause injury .
  • Be extremely careful when removing the lamp housing. In the unlikely

event that the bulb ruptures, small glass fragments may be generated.

The lamp housing is designed to contain these fragments, but use cau-

lamp’s life, the message “Change lamp” briefly appears on the projected

  • To prevent eye injury if the projector is ceiling mounted, wear protec-

the lamp has been in use. Twenty hours before the specified end of the

tor warranty and voids all certification marks on this projector.

2 Wait 45 minutes to allow the projector to cool thoroughly.

1 Turn off the projector and unplug the power cable.

lamps may cause electrical shock and fire.

Replacing the projection lamp

projector is mounted on the ceiling.

you replace the lamp.

WARNINGS :

sharpness.

screen.

Show 4 more labels / short text on this page
lamp hours · wait 45 minutes · the projector · lamp cover screw
Page 38 of the InFocus W50 user manual — Replacing the projection lamp
Page 38 · click to enlarge
Page 38

reset lamp hours in Service menu

loosen the captive screws on lamp module

6 Install the new lamp module, making sure that it is properly seated, and tighten the three captive screws.

7 Replace the cover over the lamp module by sliding it back into place and tightening the screw.

4 Loosen the three captive screws (marked by the arrows) on the lamp module. When replacing the lamp, never touch any screws without the

5 Carefully remove the lamp module by grasping and lifting the handle. Dispose of the lamp in an environmentally proper manner.

8 Plug in the power cable, press the power switch then press the Power button to turn the projector back on. Reset the lamp hour timer by navi-

gating to the Settings>Service menu and selecting Reset Lamp Hours.

arrow mark.

lamp module handle

Page 39 of the InFocus W50 user manual — Cleaning the dust filter
Page 39 · click to enlarge
Page 39
InFocus W50 — Cleaning the dust filter diagram (page 39)
Fig. 68 · Cleaning the dust filter

reset filter hours in Service menu

InFocus W50 — Cleaning the dust filter diagram (page 39)
Fig. 69 · Cleaning the dust filter

6 Replace the dust filter and the bracket on the cover, then replace the dust filter cover.

3 Remove the dust filter cover on the side of the projector by pressing up on the two tabs at the cover’s bottom.

7 Reset the filter hour timer by navigating to the Settings>Service menu and selecting Reset Filter Hours.

ordering information. Refer to the information that came with the lock for

The projector has a security lock for use with a cable lock system. See the

Accessories catalog that came with the projector, or visit our website, for

4 Pull the tab on the center of the black dust filter bracket and lift it off.

5 Clean the filter, cover, and vent using a vacuum set on low power. Replace the filter if it is damaged or too dirty to clean.

2 Wait 45 minutes to allow the projector to cool thoroughly.

1 Turn off the projector and unplug the power cable.

minutes before you clean or replace the dust filter.

Cleaning the dust filter

Using the security lock

instructions on how to use it.

tabs

Page 40 of the InFocus W50 user manual — Projected image size
Page 40 · click to enlarge
Page 40

power cord from the receptacle. Loosen the screws marked with a triangle

Table 3Projection sizes: Short Fixed lens (0.8:1 throw ratio) Minimum Image Maximum Image

Screen Size (inch/m) Minimum

40/1 24/0.6

60/1.5 35/0.9

70/1.8 43/1.1

100/2.5 63/1.6

120/3 75/1.9

150/3.8 94/2.4

200/5.1 130/3.3

250/6.4 161/4.1

300/7.6 193/4.9

350/8.9 224/5.7

areas), your retailer or your dealer.

Optional lenses

to remove the lens.

3/0.9 2.1/0.66 1.7/0.53 2.6/0.79 2.1/0.63

5/1.5 3.5/1.1 2.8/0.86 4.2/1.3 3.4/1.0

10/3.0 7.0/2.1 5.6 1.7 8.3/2.5

30/9.1 20.6/6.3 16.5/5 24.8/7.6 19.8/6.1

Table 2Projection sizes: Standard lens (1.5 - 1.8:1 throw ratio)

15/4.6 10.4/3.2 8.3/2.5 12.5/3.8 10/3

20/6.1 13.8/4.2 11/3.4 16.6/5.1 13.3/4

25/7.6 17.2/7.6 13.8/4.2 20.7/6.3 16.6/5

The image offset range for the standard lens is 9:1 (90%) to 1:1 (50%).

culators for the standard and optional lenses.

Projected image size

Appendix

Show 18 more labels / short text on this page
Projection Distance · (inch/m) · Image · Width · (feet/m) · Diagonal · (feet/m) · Image · Image · Width · (feet/m) · Diagonal · Image · (feet/m) · Min Distance · Max Distance · Distance · (feet/m)
Page 41 of the InFocus W50 user manual — Optional lenses
Page 41 · click to enlarge
Page 41

Table 4: Projection sizes: Short Zoom lens (1.2 -2.0:1 throw ratio range) Table 5: Projection sizes: Long Throw lens (1.9 - 3.9:1 throw ratio range

150/3.8 236/6.0 467/11.9

200/5.1 319/8.1 630/16.0

250/6.4 402/12.2 787/23.9

300/7.6 480/16.3 94532.0

400/10.2 642/20.4 126040.1

500/12.7 803/20.4 1579/40.1

40/1 59/1.5 122/3.1

60/1.5 94/2.4 185/4.7

70/1.8 110/2.8 217/5.5

100/2.5 157/4.0 311/7.9

120/3 189/4.8 374/9.5

70/1.8 67/1.7 110/2.8

100/2.5 98/2.5 157/4.0

120/3 118/3.0 189/4.8

150/3.8 150/3.8 240/6.1

200/5.1 197/5.0 319/8.1

250/6.4 248/6.3 402/10.2

300/7.6 299/7.6 480/12.2

350/8.9 350/8.9 559/14.2

40/1 39/1.0 63/1.6

60/1.5 59/1.5 94/2.4

Show 8 more labels / short text on this page
Minimum Maximum · Projection Distance (inch/m) · Screen Size · (inch/m) · Minimum Maximum · Projection Distance (inch/m) · Screen Size · (inch/m)
Page 42 of the InFocus W50 user manual — Optional lenses
Page 42 · click to enlarge
Page 42
Table 6Projection sizes: Ultra Long Throw lens (3.9 - 7.4:1 throw ratio

70/1.8 220/5.6 513/10.5

100/2.5 315/8.0 594/15.1

120/3 382/9.7 717/18.2

150/3.8 476/12.1 898/22.8

200/5.1 638/16.2 1197/30.4

250/6.4 799/24.4 1496/45.6

300/7.6 961/28.5 1795/53.3

400/10.2 1283/32.6 2398/60.9

500/12.7 1602/40.7 3000/76.2

40/1 122/3.1 236/6.0

60/1.5 189/4.8 354/9.0

Show 4 more labels / short text on this page
(inch/m) Minimum Maximum · Projection Distance (inch/m) · range · Screen Size
Page 43 of the InFocus W50 user manual — Command Format
Page 43 · click to enlarge
Page 43

Some commands have ranges, while others are absolute. If a number greater

than the maximum range is received, it is automatically set to the maximum

number for that function. If a command is received that is not understood, a

"?" is returned. With absolute settings, "0" is off, 1-9999 is on. The one excep-

To assure the projector can process a command, wait 3 seconds before enter-

A read command returns the range and the current setting, for example:

Lamp Hours (LMP?) (0-32766, 42)

Volume (VOL?) (0-32, 0)

Read Command Examples

tion is the Power command, where 0 is off and 1 is on.

#### denotes the value to be written

(leading zeros not necessary)

AAA denotes the command

A write request example:

) ends the command

ing the next command.

To control this projector via RS-232, connect a null modem cable and set the

control system serial port settings to match the following communication

enclosed in parentheses. The request can be a read request (indicated by a

All commands consist of 3 alpha characters followed by a request, all

Visit our website for additional RS-232 settings and information.

"?") or a write request (indicated by 1 to 4 ASCII digits).

RS-232 Port Settings

Bits per second 19,200

Communication Configuration

AAA denotes the command

? denotes the read request

RS-232 commands

A read request example:

) ends the command

Command Format

configuration:

Show 12 more labels / short text on this page
Function Command Response · Brightness (BRT?) (96-160,128) · (starts the command · (AAA####) where · Setting Value · Parity None · Flow control None · Emulation VT100 · Data bits 8 · Stop bits 1 · (starts the command · (AAA?) where
Page 44 of the InFocus W50 user manual — Limitations
Page 44 · click to enlarge
Page 44

mand Min Max Default St

e

p

ARZ at RW 0 2 2

ABT at W 0 1 n/a

AIM at W 0 1 n/a

IRI at RW 0 2 1

APO at RW 0 1 0

ASC at RW 0 1 1

BLK at RW 0 1 0

Function Com-

0. Off 1: Presentation 2: Film
0. Native 1: 16:9 2: 4:3
0. disable 1: enable
0. disable 1: enable
0. n/a 1: enable
0. n/a 1: enable
0. off 1: on

mand is issued, the command will be ignored. If a command is received that

Not all commands are supported for all projectors. If an unsupported com-

is not understood, a ‘?’ character will be returned indicating the command

The projector cannot respond to commands coming in at a high-rate. There-

fore, a delay must occur between commands to ensure that the command

The Step column refers to increasing or decreasing the menu bar position

since the On-screen Display is not an exact match of values. For example,

Step 2 changes the data by 2 through the CLI (Command Line Interface).

Brightness (BRT140) Sets the brightness to 140

gets properly executed. To assure the projector can process a command,

Power (PWR0) Turns power off

Power (PWR1) Turns power on

Write Command Examples

wait 3 seconds before entering the next command.

The menu bar is up (or down) by 1.

Error Conditions

was not understood.

Limitations

Show 8 more labels / short text on this page
About (Source Info) · Aspect Ratio · Auto Source · Auto Image · Auto Power · Active Iris · Blank · Function Command Response
Page 45 of the InFocus W50 user manual — mand Min Max Default St
Page 45 · click to enlarge
Page 45

Green Gain GCG at RW 64 192 128 1

Horizontal Keystone DKH at RW 38 218 128 1

RST at W 0 1 n/a

EFK at RW 0 15 7

DMG at RW 0 1 1

FRZ at RW 0 1 0

HDMI Noise Cancel HNC at RW 0 1 1

INT at RW 0 1 1

128 def:+1

Horizontal Position HPS at RW def:-

0. blank 1: mute 2: aspect ratio 3: source 4: auto image 5: freeze 6: zoom 7: Source Info 8: Service Info 15: AV Mute
0. not reset 1: reset
0. disable 1: enable
0. disable 1: enable
0. disable 1: enable

Blue Gain BCG at RW 64 192 128 1

Brightness BRT at RW 96 160 128 1

Color CLR at RW 96 160 128 1

Contrast CON at RW 96 160 128 1

TMP at RW 0 3 2 (computer 2,3) 0 (other)

BSC at RW 0 2 1

CEL at RW 0 1 0

CSM at RW 0 4 0

0. Auto 1: RGB 2: REC709 3: REC601 4: RGB Video
0. 9300K 1: 6500K 2: 7200K 3: User
0. black 1: blue 2: white
0. disable 1: enable
Show 10 more labels / short text on this page
28 auto 1 · Internal Sound Enable · Custom Key (Effect) · Display Messages · Factory Reset · Freeze · Blank Screen · Color Space · Color Temp · Ceiling
Page 46 of the InFocus W50 user manual — mand Min Max Default St
Page 46 · click to enlarge
Page 46

Magnify MAG at RW 0 48 0 1

izontal MPH at RW 0 64 32 1

tical MPV at RW 0 64 32 1

LRT at W 0 1 n/a

Resets LMR at R 0 32766 0

(All Bulbs) LMT at R 0 21474 83646 0

Bulb1 Lasted LB1 at R 0 32766 0

Bulb2 Lasted LB2 at R 0 32766 0

Bulb3 Lasted LB3 at R 0 32766 0

LPE at RW 0 1 0

MGE at RW 0 1 0

LML at R 0 1

Lamp Total On Time

Time In Hours Last

Time In Hours Last

Time In Hours Last

0. not reset 1: reset
0. disable 1: enable
0. disable 1: enable
0. not lit 1: lit

Lamp Hours LMP at R 0 32766 0 1

IRF at RW 0 1 1

IRR at RW 0 1 1

IRT at RW 0 1 0

LAN at RW 0 17 0

10 = Spanish 11 = Traditional Chinese

0 = English 1 = French 2 = German 3 = Italian 5 = Korean 6 = Norwegian 7 = Portuguese 8 = Russian 9 = Simplified Chinese

12 = Swedish 13 = Dutch 14 = Polish 15 = Turkish 16 = Danish 17 = Finnish

0. disable 1: enable
0. disable 1: enable
0. disable 1: enable
Show 11 more labels / short text on this page
Magnify Position Hor- · Magnify Position Ver- · Reset Lamp Hours · Number of Lamp · Magnify Enable · Low Power · Lamp Lit · IR Receiver front · IR Receiver rear · IR Receiver top · Language
Page 47 of the InFocus W50 user manual — mand Min Max Default St
Page 47 · click to enlarge
Page 47

Red Gain RCG at RW 64 192 128 1

US1 at W 0 1 n/a

US2 at W 0 1 n/a

2,3:5 computer 1,

PST at RW 0 11 computer

video:7

FRT at W 0 1 n/a

DSC at RW 0 5 1

REA at RW 0 1 0

Save User Presets 1

Save User Presets 2

0. computer 1 1: computer 2 2: computer 3 3: video 1 4: video 2 5: video 3
0. user 1 1: user 2 2: user 3 3: Presets Off 5: presentation 7: video 10: bright 11: whiteboard
0. not reset 1: reset
0. not saved 1: saved
0. not saved 1: saved
0. disable 1: enable

Phase MSS at RW 0 31 0 1

NAV at W 0 4 n/a

NTR at W 0 1 n/a

MNU at RW 0 1 0

MTE at RW 0 1 0

NND at RW 0 1 1

OVS at RW 0 1 0

PWR at RW 0 1 0

PSV at RW 0 1 0

0. not restart 1: restart
0. disable 1: enable
0. up 1: down 4: select
0. disable 1: enable
0. disable 1: enable
0. disable 1: enable
0. disable 1: enable
0. disable 1: enable
Show 13 more labels / short text on this page
Reset Filter Hours · Power-up Source · Presets · Rear · Menu Navigation · NND (PC Screen · Network Restart · Power Save · Saver Off) · Overscan · Power · Menu · Mute
Page 48 of the InFocus W50 user manual — mand Min Max Default St
Page 48 · click to enlarge
Page 48

Tint TNT at RW 96 160 128 1

Vertical Keystone DKC at RW 38 218 128 1

SA0 at RW 0 5 4

0 5 0 1 3 2 2

DSU at RW 0 2 1

SOG at RW 0 1 1

Unit Total Time On ONL at R 0 21474 83646 0

-384 def:

Tracking MTS at RW def:

Source 2:SA2

Source 3:SA3

Source 4:SA4

Source 5:SA5

Audio for Source 0

Audio for Source 1

0. audio 1 1: audio 2 2: audio 3 3: audio 4 4: HDMI Internal 5: mute
0. Sunc on G off 1: Auto
0. blank screen 1: default 2: captured
0. audio 1 1: audio 2 2: audio 3 3: audio 4 5: mute

US3 at W 0 1 n/a

SHP at RW 5 9 7 (computer and video 1)

6 (video 2 and 3)

SSV at RW 0 5 0

SRC at RW 0 5 0

0 5 0 1 3 4

Source 2:SR2

Source 3:SR3

Source 4:SR4

Save User Presets 3

0. computer1 1: computer2 2: computer 3 3: video 1 4: video 2 5: video 3
0. computer 1 1: computer 2 2: computer 3 3: video 1 4: video 2 5: video 3
0. 5 minutes 1: 10 minutes 2: 15 minutes 3: 20 minutes 4: 25 minutes 5: 30 minutes

5 = Sharpest 6 = Sharper 7 = Standard 8 = Softer 9 = Softest

0. not saved 1: saved
Show 9 more labels / short text on this page
+384 auto 1 · SA1 at RW · Sync on Green · Startup Logo · SR1 at RW · Screen Save · Sharpness · Source 1 · Source
Page 49 of the InFocus W50 user manual — mand Min Max Default St
Page 49 · click to enlarge
Page 49

Volume VOL at RW 0 32 16 1

VSU at RW 0 3 0

128. 0 else:

Vertical Position VPS at RW if

0. Auto 1: NTSC 2: PAL 3: SECAM
Show 5 more labels / short text on this page
+128 auto 1 · def · def< · def - · Video Standard
Page 50 of the InFocus W50 user manual — mand Min Max Default St
Page 50 · click to enlarge
Page 50
Page 50 of the InFocus W50 user manual — mand Min Max Default St
Page 51 of the InFocus W50 user manual — mand Min Max Default St
Page 51 · click to enlarge
Page 51
Page 51 of the InFocus W50 user manual — mand Min Max Default St
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No startup screenPlug power cable in, press power switch and power button. Remove lens cap. 3 2 1 p.17
Only startup screen appears/no computer image startu pn A screePress the Source button Activate laptop’s external port or restart laptop p.17
Set your computer’s display resolution to the native resolution of the projector (Start>Settings>Control Panel>Display>Settings tab, select1024x768) For a laptop, disable laptop monitor or turn-on dual- display mode p.18
Image not squareAdjust keystone the Picture menu p.19
Image not sharp A BAdjust the focus ring or Sharpness in the Picture>Advanced menu p.19
Image does not fit 16:9 screenChange aspect ratio to 16:9 in Picture>Aspect ratio menu p.19

Ask about the InFocus W50

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus W50

Be the first to ask — other owners or our team will answer.

Original document

InFocus W50 manual PDF

51 pages·2.3 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…