EN
InFocus logo
Official user manual

InFocus SP8600

45 pages·9.5 MB·Projector·PDF·ENDEFRITNLJA
InFocus SP8600
Table of Contents 32 sections Introduction · Positioning the projector · Ceiling Mount · Cable management · … ShowHide
Page 1 of the InFocus SP8600 user manual
Page 1 · click to enlarge
Page 1
InFocus SP8600 diagram (page 1)
Fig. 1
Page 2 of the InFocus SP8600 user manual — Trademarks
Page 2 · click to enlarge
Page 2
Declaration of Conformity ManufacturerInFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation.

We declare under our sole responsibility that this projector conforms to the following directives and norms:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

EMC Directive 2004/108/EC EuP Directive 2005/32/EC EMC: EN 55022

EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 2006/95/EC Safety: IEC 60950-1:2005, MOD

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment. Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Agency Approvals

Other specific Country Approvals may apply. Please see product certification label.

This document applies to regulatory model H8300.

Input ratingsAC 100-240V, 4.3-1.6A,50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

UL, cUL

Page 3 of the InFocus SP8600 user manual
Page 3 · click to enlarge
Page 3

Table of Contents Introduction 5 Positioning the projector 7 Ceiling Mount 8 Cable management 9 Connecting power 10 Connecting a computer source 10 Displaying an image 11 Adjusting the image 12 Connecting a video device 13 Video device connections 13 Shutting down the projector 15 Troubleshooting your setup 15 Using the remote control 23 Using the keypad buttons 24 Optimizing computer images 24 Presentation features 24 Optimizing video images 25 Customizing the projector 25 Using the menus 26 Basic Picture menu 27 Advanced Picture menu 28 Setup menu 29 Status and Service menu 31 Help 31 Maintenance 32 Cleaning the lens 32 Replacing the projection lamp 33 Using the security lock 34 Appendix 35 SplitScreen Compatibility 35 RS-232 commands 36 Index 44

Page 4 of the InFocus SP8600 user manual — Important Operating Considerations for Safety
Page 4 · click to enlarge
Page 4

Important Operating Considerations for Safety

  • The projector remote control uses batteries. Make sure the batteries’ polarity (+/-) is aligned correctly. Dispose of used batteries in accordance with local disposal laws.
  • Refer to this guide for proper startup and shutdown procedures.
  • Follow all warnings and cautions in this manual and on the projector.
  • Use an InFocus approved ceiling mount kit for proper fitting, ventilation and installation. The projector warranty does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper location.
  • Place the projector in a horizontal position no greater than 8 degrees off axis.
  • Locate the projector at least 4' (1.2m) away from any heating or cooling vents.
  • Do not block ventilation openings. Locate the projector in a well-ventilated area without obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
  • When the projector is ceiling mounted, wear protective eyewear to prevent eye injury before opening lamp door.
  • The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself.
  • Do not place the projector in direct sunlight, humid, greasy or dusty places or in places where the projector may come into contact with smoke or steam.
  • Do not touch the exhaust vents. This area will become hot while the projector is being used. Be sure children are kept away from this area.
  • Refer all service to qualified service personnel. Servicing your own projector can be dangerous to you and will void the warranty.
  • Do not look directly into the lens while the projector is being used. Be especially careful that children do not stare directly into the lens.
  • Only use replacement parts specified by InFocus. Unauthorized substitutions may result in fire, electrical shock, or injury, and may void the warranty
  • Do not push objects of any kind into this projector through its venting as object may touch dangerous voltage that could result in a fire or electrical shock.
  • Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty.
  • Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See <a href="http://www.lamprecycle.org" rel="nofollow noopener" target="_blank">www.lamprecycle.org</a> .
  • Do not drop the projector.
  • Do not spill liquid on the projector. Spilled liquid may damage the projector.
  • Do not place any object on the projector.
  • The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
  • Do not stand or step on the projector.
  • Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal. The AC power cord has a three-pin grounding-type power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. Do not remove the grounding pin on the power plug.
  • In the unlikely event of a lamp rupture, particles may exit through the projector vents. Keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.
  • A surge-protected power strip is recommended. Do not overload wall outlets.
  • When disconnecting the power cord, hold the plug, not the cord. Unplug the projector from the wall outlet, if the projector is unused for an extended time.
  • Wash hands after handling the cables supplied with this product.
Page 5 of the InFocus SP8600 user manual
Page 5 · click to enlarge
Page 5
InFocus SP8600 diagram (page 5)
Fig. 2

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • When the power cord or plug is damaged or frayed
  • If liquid has been spilled into the projector
  • If the projector has been exposed to rain or water
  • If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and may required extensive work to restore the projector to normal operation
  • If the projector has been dropped
  • When the projector exhibits a distinct change in performance, this indicates a need for service.

Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.

Page 6 of the InFocus SP8600 user manual — Included Items
Page 6 · click to enlarge
Page 6

Introduction

Optional Accessories Optional accessories include optional top covers in a variety of finishes, the Commander-2 remote, ceiling mount, and LiteShow II. These items and other accessories can be found on our website at www.infocus.com or at your local dealer.

Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for home video viewing and business presentations, too. The SP8602 has native 1920x1080 (1080p) resolution. Your projector is compatible with a wide variety of computers and video devices.

InFocus SP8600 — Introduction diagram (page 6)
Fig. 3 · Introduction

Product specifications To read the latest specifications on your multimedia projector, be sure to visit our support website at www.infocus.com/support, as specifications are subject to change.

Online registration Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.

Included Items

InFocus SP8600 — Included Items diagram (page 6)
Fig. 4 · Included Items
InFocus SP8600 — Included Items diagram (page 6)
Fig. 5 · Included Items

Documentation

Page 7 of the InFocus SP8600 user manual — Introduction
Page 7 · click to enlarge
Page 7

Connector panel The projector provides both computer and video connection options, including:

InFocus SP8600 — Introduction diagram (page 7)
Fig. 6 · Introduction
  • VGA computer
  • HDMI (2)
  • S-video
  • Composite video
  • Component video (3)
  • USB port

The projector also provides the following connectors:

  • 12V screen trigger outputs (3)
  • IR Repeater input (for use with IR receivers that follow the Xantech connector specification T=Signal, R= GND, S=12VDC)
  • RS-232 connector for serial control. Command control codes are in the Appendix and on our support website at <a href="http://www.infocus.com/support" rel="nofollow noopener" target="_blank">www.infocus.com/support</a> . 12V External Trigger outputs The three 3.5mm mini-jack 12 volt, 0.25 amp DC outputs are screen/lens triggers:
  • The “Lamp” trigger turns on when the lamp is lighted. If you connect your projection screen to this output using the cable that came with your screen, the screen will move down when the lamp is turned on and the screen will return to its storage position, when the lamp is turned off.
  • The Letterbox “1” and “2” triggers are active when the projector is placed in letterbox mode and are utilized for variable masking and anamorphic lens control. (These triggers are off when SplitScreen is active.)
Page 8 of the InFocus SP8600 user manual — Positioning the projector
Page 8 · click to enlarge
Page 8

Positioning the projector

  • The vertical image offset range is 105%~130% for the SP8602 (default is 105%). The default horizontal image offset is +/-15%, however at maximum vertical image offset, there is no horizontal lens shift.

To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:

InFocus SP8600 — Positioning the projector diagram (page 8)
Fig. 7 · Positioning the projector
  • Position the projector on a flat surface at a right angle to the screen. The projector must be at least 4.9’ (1.5m) from the projection screen.
  • Position the projector within 10’ (3m) of your power source and within 6’ (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6” (.15m) of a wall or other object.
  • Position the projector to the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.
  • If the image is square but not centered on the screen or viewing area, adjust it by using the lens shift dials. Use the Horizontal dial to shift the lens left or right. Use the Vertical dial to shift the lens up or down.
InFocus SP8600 — Positioning the projector diagram (page 8)
Fig. 8 · Positioning the projector

1 Use vertical lens shift to move the image closer to the lens centerline than the final vertical position.

2 Use horizontal lens shift to determine the center horizontal position, then move image to the center horizontal position.

3 Use vertical lens shift to move the image away from the lens centerline to the final vertical position.

4 Use horizontal lens shift to move the image to the final horizontal position.

5 If lens shift is unable to move the image far enough, move the projector (preferable) or tilt the projector and then use vertical and horizontal keystone to re-position the image.

Horizontal Offset +/-15%

Page 9 of the InFocus SP8600 user manual — Ceiling Mount
Page 9 · click to enlarge
Page 9

Ceiling Mount

Range of distance to the screen for a given screen size

If you wish to install the projector on the ceiling:

Diagonal Screen Size (inches/m)Distance to screen Minimum Maximum Distance distance (feet/m) (feet/m) 60/1.524 80/2.032 90/2.286 150/3.8106.50/1.98 10.01/3.05 8.73/2.66 13.42/4.09 9.84/3.00 15.12/4.61 16.54/5.04 25.3/7.71
InFocus SP8600 — Ceiling Mount diagram (page 9)
Fig. 9 · Ceiling Mount
  • The projector must be installed by a qualified professional in order to ensure proper operation and reduce the risk of hazards or injury. It is not recommended you install the projector yourself.
  • We strongly recommend using InFocus approved ceiling mounts for proper fitting, ventilation and installation. Refer to the installation guide that comes with the InFocus Ceiling Mount Kit (p/n SP-CEIL-INSTALL) for more information. The warranty does not cover any damage caused by use of nonapproved ceiling mount kits or by installing in an improper location.
  • The ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. Consult your dealer for more information.
  • Maximum supported physical pitch is +/-8º.
  • Maximum supported physical horizontal roll is +/-8º.
  • Keep all adjacent surfaces 3” (76mm) from sides, front and rear and .87” (22mm) from the bottom of projector to preserve required airflow around the projector.
InFocus SP8600 — Ceiling Mount diagram (page 9)
Fig. 10 · Ceiling Mount
Page 10 of the InFocus SP8600 user manual — Cable management
Page 10 · click to enlarge
Page 10

Cable management

The integrated cable management system allows you to keep the cables organized. To use the cable management system, thread the cables into the slots as shown in the illustration.

InFocus SP8600 — Cable management diagram (page 10)
Fig. 11 · Cable management

cable management system Using the cable management system provides you with a clean, professional-looking installation.

Page 11 of the InFocus SP8600 user manual — Connecting a computer source
Page 11 · click to enlarge
Page 11

Connecting power

InFocus SP8600 — Connecting power diagram (page 11)
Fig. 12 · Connecting power

Connect the black power cord to the Power connector on the rear of the projector and to your electrical outlet. The Power light on the Status Indicator Panel (page 15) turns amber.

Connecting a computer source

HDMI 1.3 connection HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video out connector on the video device and into either the HDMI 1 or HDMI 2 connector on the projector.

InFocus SP8600 — Connecting a computer source diagram (page 11)
Fig. 13 · Connecting a computer source

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3- compatible source.

VGA connection Connect one end of the provided computer cable to the VGA connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first.

InFocus SP8600 — Connecting a computer source diagram (page 11)
Fig. 14 · Connecting a computer source

Connect HDMI cable

Page 12 of the InFocus SP8600 user manual — Displaying an image
Page 12 · click to enlarge
Page 12

Displaying an image

InFocus SP8600 — Displaying an image diagram (page 12)
Fig. 15 · Displaying an image

Touch the Power button on the keypad or the remote.

The Power button blinks green and the fans start to run. When the lamp turns on, the start up screen will display and the Power button will become solid green. It can take a minute for the image to achieve full brightness.

No start up screen? Get help on page 16.

Turn on computer or video device

Turn on your computer or video device.

InFocus SP8600 — Displaying an image diagram (page 12)
Fig. 16 · Displaying an image

The image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad or remote.

If you are using a VGA cable to connect your computer to the projector:

If using a laptop, make sure its external video port is active.

Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like Fn + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press Fn and the labeled function key simultaneously.

Activate laptop’s external port

Monitor key or LCD/CRT key

InFocus SP8600 — Displaying an image diagram (page 12)
Fig. 17 · Displaying an image

Refer to your laptop’s documentation for more information about your laptop’s key combination or go to the InFocus website at: http://www.infocus.com/Support/ LaptopActivation.aspx.

No laptop image? Try pressing the Auto Image button on the keypad or remote.

Press Power button · Fn key

Page 13 of the InFocus SP8600 user manual — Adjusting the image
Page 13 · click to enlarge
Page 13
InFocus SP8600 — Adjusting the image diagram (page 13)
Fig. 18 · Adjusting the image

Adjusting the image

Position the projector to the desired distance from the screen at a 90 degree angle to the screen. See page 8 for a table listing of screen sizes and distances.

Remove the projector top cover

a. Slide the tabs on the side toward the rear of the projector to unlock the projector top cover.

b. Slide the top toward the front of the projector to unhook it from the projector body.

c. Lift off.

Adjust the zoom or focus.

focus Adjust zoom, focus and lens shift

If the image is square but not centered on the screen or viewing area, adjust it by using the lens shift dials. See page 7 for details.

Rotate the elevator feet for granular adjustment of the projector’s height. Avoid placing your hands near the hot exhaust vent at the side of the projector.

Adjust the Contrast or Brightness in the Basic Picture menu. See page 27 for help with these menu adjustments.

Show 4 more labels / short text on this page
Adjust distance · Remove cover · Adjust height · Elevator foot
Page 14 of the InFocus SP8600 user manual — Video device connections
Page 14 · click to enlarge
Page 14

Connecting a video device

HDMI 1.3 connection HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video out connector on the video device and into either the HDMI 1 or HDMI 2 connector on the projector.

You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector.

You can connect the projector to most video devices that can output video. You cannot directly connect the coaxial cable that enters your house from a cable or satellite company; the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.

To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3- compatible source.

S-video connection If your video device uses a round, four-prong S-video connector, plug an S-video cable into the S-video connector on your video device and into the S-video connector on the projector.

Although the aspect ratio is automatically selected by the projector based on the signal input, you can change the aspect ratio, if desired. The projector’s Aspect Ratio setting is accessed through the Resize button on the remote or through the projector’s Basic Picture Menu. See page 27 for more information.

Keep in mind that S-video delivers higher quality video output than composite.

VGA connection If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the VGA connector on the projector.

Video device connections

You can order cables from InFocus or use your own.

Composite video connection Plug the composite video cable’s yellow connector into the video out connector on the video device. Plug the other yellow connector into the yellow Composite connector on the projector.

Component video connection Plug the component cable into the video device. Plug the other end of the component cable into the Component 1, Component 2 or Component 3 connectors.

Keep in mind that video output from composite connections is not as high quality as S-video.

In addition, a Component to VGA adapter can be used in conjunction with the VGA connectors. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the VGA connector.

Component offers the highest quality analog video output.

Page 15 of the InFocus SP8600 user manual — Connecting a video device
Page 15 · click to enlarge
Page 15

What is Aspect Ratio? Aspect ratio is the ratio of the image width to image height. HDTV and most DVDs are 16:9, which is the default for this projector. When in 4:3 mode the projector places black bars on both sides of the image. Native mode centers the image and turns off the internal scaler so that any resolution larger than the native projector resolution is cropped on the edges. Letterbox expands the image to fill the screen. Natural Wide stretches a 4:3 image to fill the entire 16:9 screen. The center two- thirds of the image is unchanged; the edges of the image are stretched.

16:9 image input

16:9 image

16:9 aspect ratio

What you plan to project will also help you choose between 4:3 and 16:9. For example, most TV shows are 4:3, while most movies are 16:9. If you have a 16:9 screen, then you should select an aspect ratio of 16:9 for anamorphic movies and HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for anamorphic movies or HDTV, but you also have the option of using 4:3, Native, or Natural Wide for 4:3 content. Force Wide can also be enabled to automatically resize less common aspect ratios to 16:10.

4:3 image input 4:3 image on 16:9 screen

4:3 aspect ratio

letterbox image input 16:9 image fills 16:9 screen

4:3 image input 4:3 image fills 16:9 screen

natural wide aspect ratio

letterbox aspect ratio

Page 16 of the InFocus SP8600 user manual — Table 1: Status indicator light behavior and meaning
Page 16 · click to enlarge
Page 16

Shutting down the projector

Troubleshooting your setup

Screen Save Time You can make the black screen appear after a preset number of minutes by turning on the Screen Save Time feature in the Setup menu. See page 29.

The Status Indicator Panel on top of the projector indicates the state of the projector and is a helpful when troubleshooting.

Auto Off Time The projector has an Auto Off Time feature that automatically turns the projector off if no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off. You can change the length of time, see page 29.

Table 1: Status indicator light behavior and meaning

The projector is plugged in.

Turning off the projector To turn the projector off, press the Power button on the remote or keypad. The lamp turns off and the LED blinks amber for 10 seconds while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely power off the projector.

The power button has been pressed and the software is initializing.

The projector is on and initialized.

The power button has been pressed to turn the projector off and the fans are running to cool the projector.

Temperature The projector is too hot. Make sure the vents aren’t blocked (see page 21). Turn the projector off and wait one minute, then turn the projector on again. Contact Technical Support if the problem persists. Visit www.infocus.com/support to contact service.

Lamp Turn the projector off and wait one minute, then turn the projector on again. If the lamp light turns on again, replace the lamp and reset the lamp timer (page 34).

Wrench/Service Turn the projector off and wait one minute, then turn the projector on again. If the service lamp turns on again, service is required. Visit www.infocus.com/support to contact service.

Show 5 more labels / short text on this page
Icon Meaning · Power, solid amber · Power, blinking green · Power, solid green · Power, blinking amber
Page 17 of the InFocus SP8600 user manual — Shutting down the projector
Page 17 · click to enlarge
Page 17
InFocus SP8600 — Shutting down the projector diagram (page 17)
Fig. 19 · Shutting down the projector

No start up screen Plug power cord into the projector, then press power button

Press the Source button Activate the laptop’s external port

Page 18 of the InFocus SP8600 user manual — Shutting down the projector
Page 18 · click to enlarge
Page 18
InFocus SP8600 — Shutting down the projector diagram (page 18)
Fig. 20 · Shutting down the projector

No computer image, just the words “Signal out of range”

Press the Auto Image button on the keypad or on the remote. To adjust computer refresh rate, go to Control Panel > Display > Settings > Advanced > Adapter (location varies by operating system).

You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped”

Only my laptop’s background appears, not the Desktop icons

Windows - Disable “Extend my Windows Desktop” in Control Panel > Display > Settings > Display 2 (location varies by operating system)

Page 19 of the InFocus SP8600 user manual — Shutting down the projector
Page 19 · click to enlarge
Page 19
InFocus SP8600 — Shutting down the projector diagram (page 19)
Fig. 21 · Shutting down the projector

Set your computer’s display resolution to the native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab)

For a laptop, disable laptop monitor or turn- on dual-display mode

Image not centered on screen Move projector, adjust zoom and lens shift

Page 20 of the InFocus SP8600 user manual — Shutting down the projector
Page 20 · click to enlarge
Page 20

Adjust Keystone in the Basic Picture menu Square image

InFocus SP8600 — Shutting down the projector diagram (page 20)
Fig. 22 · Shutting down the projector

Adjust Sharpness in the Basic Picture menu Correct image

InFocus SP8600 — Shutting down the projector diagram (page 20)
Fig. 23 · Shutting down the projector

Image does not fit 4:3 or 16:9 screen Change aspect ratio to 4:3 or 16:9 in Basic Picture>Aspect Ratio menu

InFocus SP8600 — Shutting down the projector diagram (page 20)
Fig. 24 · Shutting down the projector
Show 4 more labels / short text on this page
Problem Solution Result · Image not square · Image not sharp · Correct image
Page 21 of the InFocus SP8600 user manual — COLOR
Page 21 · click to enlarge
Page 21

Image upside down A

Turn off Ceiling Mount in Setup menu

InFocus SP8600 — Image upside down A diagram (page 21)
Fig. 25 · Image upside down A

Image reversed left to right

Turn off Rear Project in Setup menu

InFocus SP8600 — Image upside down A diagram (page 21)
Fig. 26 · Image upside down A

A

Projected colors don’t match source

Adjust color, tint, brightness, contrast in the Basic Picture menu and/or color space in the Advanced Picture menu

InFocus SP8600 — A diagram (page 21)
Fig. 27

COLOR

COLOR

Show 4 more labels / short text on this page
Problem Solution Result · Correct image · Correct image · Correct image
Page 22 of the InFocus SP8600 user manual — Shutting down the projector
Page 22 · click to enlarge
Page 22
InFocus SP8600 — Shutting down the projector diagram (page 22)
Fig. 28 · Shutting down the projector

The video embedded in my PowerPoint presentation does not play on the screen

Turn off the internal LCD display on your laptop

Make sure vents aren’t blocked, turn the projector off and allow it to cool for one minute.

Page 23 of the InFocus SP8600 user manual — Shutting down the projector
Page 23 · click to enlarge
Page 23
InFocus SP8600 — Shutting down the projector diagram (page 23)
Fig. 29 · Shutting down the projector

“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on

If you need assistance, visit our support website at www.infocus.com/support or call us. Check out the How To section for additional information on using this projector for home theater or gaming applications.

This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.

Page 24 of the InFocus SP8600 user manual — Using the remote control
Page 24 · click to enlarge
Page 24

Using the remote control

  • Source 1, 2, 3 switches between user assigned sources.

The remote uses two (2) AA batteries. You can install the batteries by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.

  • Make sure the batteries are installed in the proper orientation and are not dead.
  • Make sure you’re pointing the remote at the projector or the screen, not the computer, and are within the remote range of 30’ (9m). For best results, point the remote at the projector.
  • When disposing of the batteries, be sure to do so in an environmentally proper manner.
  • If the remote control gets wet, wipe it dry immediately.
  • Avoid excessive heat and humidity.
  • Ensure the batteries’ polarity (+/-) is aligned correctly.
  • Do not mix new and old batteries together, or different types of batteries together.
  • Replace the batteries as soon as they run out.
  • Remove batteries from the remote control when storing or not in use for a prolonged period.

To operate, point the remote at the front of the projector (not at the computer). The range of optimum operation is about 30’ (9m).

Press the remote’s Power button to turn the projector on and off (see page 15 for shutdown information).

Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust values in the menus. See page 26 for more information on the menus.

The remote also has the following buttons:

  • Help accesses the projector’s help feature (see page 31).
  • Resize switches between aspect ratios (see page 27).
  • Overscan removes noise at the edge of a video image.
  • Source switches between sources.
  • Custom can be assigned to a special function, like Blank Screen or Freeze (see page 29).
  • Auto Image resynchronizes the projector to the source.
  • Presets selects between different stored settings (see page 27).

Troubleshooting the remote · Navigation buttons

Page 25 of the InFocus SP8600 user manual — Presentation features
Page 25 · click to enlarge
Page 25

Using the keypad buttons

Optimizing computer images

After the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 26.

Most buttons are described in detail in other sections, but here is an overview of their functions:

Power–turns the projector on and off (page 10).

  • Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu (page 27).

Auto Image–resynchronize the projector to the source.

Presets–cycles through the available preset settings (page 27).

  • Change the Aspect Ratio. Choose the option that best fits your input source (page 27).

Menu–opens the onscreen menus (page 26).

  • Adjust the Color Temperature in the Advanced Picture menu (page 28).

Select–confirms choices made in the menus (page 26).

  • Adjust the Phase, Tracking, or Horizontal or Vertical position in the Advanced Picture menu (page 28).

Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus (page 26).

  • Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 27).

Source–changes the active source (page 10).

Help–button to access the projector’s help feature (page 31)

Presentation features

InFocus SP8600 — Presentation features diagram (page 25)
Fig. 30 · Presentation features

Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section.

  • The Custom key allows you to assign various features to the button. The default effect is Source Info, which displays information about the projector and current source. See page 29 for details.
  • The Search Screen option lets you change the appearance of the blank screen and start up screen (page 30).
  • Two options, Auto Off and Screen Save Time, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 29). Menu navigation buttons
Page 26 of the InFocus SP8600 user manual — Customizing the projector
Page 26 · click to enlarge
Page 26

Optimizing video images

After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 26.

  • Adjust the Keystone, Contrast, Brightness, Color, Tint or Sharpness in the Basic Picture menu (page 27).
  • Change the Aspect Ratio. Choose the option that best fits your input source (page 27).
  • Adjust the Color Temperature. Select a listed warmth value (page 28).
  • Turn on Overscan to remove noise on the edges of the image (page 28).

Customizing the projector

You can customize the projector for your specific setup and needs. See page 29 to page 30 for details on these features.

  • For rear projection, turn Rear Project on in the Setup menu.
  • For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.
  • Specify which source the projector checks first for active video during power-up.
  • Specify the function of the Custom key on the remote.
  • Turn the projector’s display messages on and off.
  • Turn on power saving features.
  • Specify appearance of blank screen and startup screen.
  • Specify the language viewed on the menus.
Page 27 of the InFocus SP8600 user manual — Using the menus
Page 27 · click to enlarge
Page 27

Using the menus

InFocus SP8600 — Using the menus diagram (page 27)
Fig. 31 · Using the menus

To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to highlight the desired menu, then press the Select button.

To change a menu setting, highlight it, press Select, then use the arrow buttons to adjust the value or select an option or turn the feature on or off. Press Select to confirm your changes. Use the arrow buttons to navigate to another setting. When your adjustments are complete, press Menu to access a different menu; press the Menu button at any time to navigate to the higher-level menu and ultimately close the menus.

InFocus SP8600 — Using the menus diagram (page 27)
Fig. 32 · Using the menus
InFocus SP8600 — Using the menus diagram (page 27)
Fig. 33 · Using the menus

The menus are grouped by usage:

  • The Basic Picture menu provides common image adjustments.
  • The Advanced Picture menu provides more complex image adjustments.
  • The Setup menu provides set-up type adjustments that are not changed often.
  • The Status and Service menu provides information about the projector and source.

Basic Picture menu Advanced Picture menu

InFocus SP8600 — Using the menus diagram (page 27)
Fig. 34 · Using the menus
InFocus SP8600 — Using the menus diagram (page 27)
Fig. 35 · Using the menus

Setup menu Status and Service menu

Page 28 of the InFocus SP8600 user manual — Basic Picture menu
Page 28 · click to enlarge
Page 28

Basic Picture menu

Digital Zoom: Changes the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz Shift and Vert Shift settings.

To adjust the following settings, highlight the setting, press Select, use the arrow buttons to adjust the values, then press Select to confirm the changes.

Horz Shift/Vert Shift: Moves the display area horizontally or vertically if its size has been changed by the Digital Zoom setting

Brightness: Changes the intensity of the image.

Contrast: Controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.

Sharpness: Changes the clarity of the edges of a video image. Select a sharpness setting.

Color: Adjusts a video image from black and white to fully saturated color. The color setting applies to video sources only.

Tint: Adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only.

SplitScreen: Allows two distinct sources to be displayed simultaneously. Switch primary sources, make picture adjustments and choose one of multiple display options: either two side by side horizontal or vertical source regions, or a small secondary source image displayed on top of the primary source in one of four placement options. For display options, see page 35.

Auto Image: Forces the projector to reacquire and lock to the input signal. This is useful when signal quality is marginal.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9.

Select Auto to have the projector choose the ratio. Choose Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs.

For more information regarding Aspect Ratio, see page 14.

Apply Preset...: Presets are provided that optimize the projector for displaying computer presentations and video images under certain conditions.

There is also a user-definable preset. To set this preset, adjust the image and select Save User in the Presets menu. You can recall these settings in the future by selecting the User preset.

Increasing keystone Decreasing keystone

Horz/Vert Keystone: Adjusts the image horizontally and vertically and makes a squarer image.

Basic Picture menu · Aspect ratio

Page 29 of the InFocus SP8600 user manual — Advanced Picture menu
Page 29 · click to enlarge
Page 29

Advanced Picture menu

Motion Smoothing: This feature predicts the motion direction of objects and pixels, and generates more frames to smooth the image and action, resulting in a very crisp image.

BrilliantColor™: Produces an expanded onscreen color spectrum that delivers enhanced color saturation for bright, true-to-life images. Choose Normal Look for most video sources and Bright Look for most computer sources.

Gamma: Select the appropriate gamma from among Video, Film, Bright, and CRT.

Iris/DynamicBlack: Select Auto to constantly adjust the aperture based on the amount of black in the current scene, or select a percentage for a fixed aperture size (100% is maximum size).

Color Gamut: Sets the color gamut of the input signal.

Color Gain: Adjusts the gain of the red, green, or blue channel of the image.

Color Offset: Adjusts the offset of the red, green, or blue channel of the image.

Color Temperature: Changes the intensity of the colors. Select a listed relative warmth value.

Horizontal/Vertical Position: Adjusts the position of a computer source.

Overscan: Removes noise around the video image.

Horizontal/Vertical Pincushion: Correct optical pincushion distortion.

Phase: Adjusts the horizontal phase of a computer source.

Sync Threshold: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, select this option to help it to sync when connected to the projector.

InFocus SP8600 — Advanced Picture menu diagram (page 29)
Fig. 36 · Advanced Picture menu

Tracking: Adjusts the vertical scan of a computer source.

Color Space: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources or choose either REC709 or REC601 for component video sources.

Noise Reduction: Reduces temporal and/or spatial noise in the image.

Flesh Tone Correction: Controls the amount of flesh tone correction applied to the image.

Set Black Level...: Analyzes the current input image and calculates an offset value which is then added to the analog to digital converter black level value. This ensures optimum black level for each analog source.

Detect Film: Controls film mode detection, and determines whether the original source of the input video was film or video.

Advanced Picture menu

Page 30 of the InFocus SP8600 user manual — Setup menu
Page 30 · click to enlarge
Page 30

Setup menu

Screen Save Time: Automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a remote or keypad button is pressed.

Language: Allows you to select a language for the onscreen display.

Key Click: Turns the key click sound on or off. When this setting is on, pressing keys on the keypad causes the projector’s speaker to play a “click” sound.

Sleep Timer: Allows the projector to automatically power off after it has been on for a specified amount of time.

Blank Key: Select what to display when the blank key on the remote is pressed: a solid color screen (blue, black or white), the factory logo screen, a timer, or test patterns. The timer option is useful for classroom tests or break times during meetings.

Always-On Functions: Enables IR Repeater and USB functions while the projector is off. Selecting this setting increases the amount of power used by the projector while off.

Lamp Low Power: Toggles between On and Off. Turn it Off to raise the light output of the lamp. This also raises the fan speed, making the projector louder. Default is On.

Custom Key: Allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.

Power Sounds: Controls whether the projector makes a sound when powered on and off.

  • Source Info : The default action. Shows the Source Info menu.
  • Projector Info : Shows the Projector Info menu.
  • Aspect Ratio : Sets the ratio of image width to image height (see page 14 and page 27).
  • Auto Image : Resynchronizes the projector to the source (page 24).
  • Overscan : Removes noise around the image.
  • Freeze Screen : Pauses the projected image.
  • Source : Cycles through available sources.
  • Closed Captions : Enables or disables Closed Captioning.
  • SplitScreen : Enables or disables SplitScreen. Before using this for the first time, configure SplitScreen sources and layouts using the SplitScreen menu (page 27) Source Key : Enables or disables Source Keys on the optional Commander-2 remote.

Auto Source: When this feature is On, the projector automatically finds the active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up Source. To display another source, you must manually select one by pressing the Source button on the remote or keypad.

Power-up Source: Determines which source the projector checks first for active video during power-up.

Fast Color Refresh: Changes the color wheel speed from 4x to 6x.

Closed Captions: Controls closed caption display while audio is not muted. If this setting is not off, and audio is not muted, and the source is NTSC and contains captions on the selected channel, then the projector must display caption text overlaid on the image.

Ceiling Mount: Turns the image upside down for ceiling-mounted projection.

AC Power On: When this feature is on, the projector automatically turns on when electrical power is connected. This allows control of ceiling mounted projectors with a wall power switch.

Rear Project: Reverses the image so you can project from behind a translucent screen.

Auto Off Time: Automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image will be displayed.

Prevent PC Screen Saver: Prevents your computer from going into Screen Save mode. The projector must be connected to the PC via a USB cable for this feature to work.

Page 31 of the InFocus SP8600 user manual — Setup menu
Page 31 · click to enlarge
Page 31

Search Screen: Allows you to display one of the following options instead of the default screen at startup, and when no source is detected. Options include the factory logo screen, or a blue, black or white screen.

InFocus SP8600 — Setup menu diagram (page 31)
Fig. 37 · Setup menu

Show Messages: Displays status messages (such as “Searching”) in the lower-left corner of the screen.

Menu Offset: Allows you to change the position of the On Screen Display items.

Menu Transparency: Allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible.

Magnify Controls: Allows you to change the function of the arrow buttons when the menu is not shown. By default, the arrow buttons allow you to advance slides while in PowerPoint’s SlideShow mode. To make the arrow buttons also adjust magnify settings, choose Magnify Controls to turn magnify controls on. Now when the menu is not shown, you can press the Select button to switch between the magnification settings (Magnify Level, Magnify Horizontal Position and Magnify Vertical Position), then press Select again to turn off magnify controls and use the arrow buttons to advance slides.

Keypad: Enables or disables keypad.

Glow Ring: Controls the brightness level of the glow ring status indicator.

Serial Port, Baud Rate: Selects the serial port and baud rate.

Serial Port Echo: Controls whether the serial port echoes characters.

Setup menu

Page 32 of the InFocus SP8600 user manual — Status and Service menu
Page 32 · click to enlarge
Page 32

Status and Service menu

Help

Source Info: Displays current source settings (read-only).

Press Help (on the keypad or remote) at any time to get interactive help for solving common, picture, sound, and cabling problems.

Projector Info: Displays current projector settings (read-only).

Reset Lamp Hours: Resets the lamp hours used counter in the Projector Info menu to zero. Do this only after changing the lamp.

InFocus SP8600 — Status and Service menu diagram (page 32)
Fig. 38 · Status and Service menu

HDMI Long Cable: Adjusts the input for different lengths of HDMI cable. Enable for HDMI cables greater than 5 meters and disable for HDMI cables less than 5 meters.

Factory Reset: Restores all settings to their default.

Service Code: Only used by authorized service personnel.

InFocus SP8600 — Status and Service menu diagram (page 32)
Fig. 39 · Status and Service menu

Status and Service menu

Page 33 of the InFocus SP8600 user manual — WARNINGS:
Page 33 · click to enlarge
Page 33

Maintenance

InFocus SP8600 — Maintenance diagram (page 33)
Fig. 40 · Maintenance

Cleaning the lens

1 Turn the projector off and unplug the power cord.

2 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

  • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

3 Lightly wipe the cleaning cloth over the lens in a circular motion.

WARNINGS:

  • Turn the projector off and unplug power cord before cleaning any part of the projector.
  • Do not open any cover on the projector, except the lamp cover or projector top cover.
  • Do not attempt to service this product yourself as opening and removing covers may expose you to dangerous voltage and other hazards. Refer all servicing to qualified service personnel.
Page 34 of the InFocus SP8600 user manual — WARNINGS :
Page 34 · click to enlarge
Page 34

Replacing the projection lamp

1 Turn the projector off and unplug the power cord.

The lamp hours timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, the message “Replace lamp” appears on the screen at startup.

2 Wait 60 minutes to allow the projector to cool thoroughly.

3 Remove the lamp door by removing the screws on the side of the lamp door, and lifting the door off.

  • NOTE : Be sure to use the InFocus lamp module designed for this projector. You can order new lamps from <a href="http://www.infocus.com" rel="nofollow noopener" target="_blank">www.infocus.com</a> (in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not liable for the performance, safety or certification of any other lamps.
InFocus SP8600 — Replacing the projection lamp diagram (page 34)
Fig. 41 · Replacing the projection lamp

WARNINGS :

  • The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
  • To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
  • Unplug the power cord before replacing the lamp.
  • Do not drop the lamp module. The glass may shatter and cause injury.
  • Do not touch the glass surface of the lamp module. Fingerprints can obscure projection sharpness and may cause the glass to shatter.
  • Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp module is designed to contain most of these fragments, but use caution when removing it.
  • Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.
  • When replacing the lamp while the projector is ceiling-mounted, wear protective eyewear to prevent eye injury.
  • Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See <a href="http://www.lamprecycle.org" rel="nofollow noopener" target="_blank">www.lamprecycle.org</a> .
Page 35 of the InFocus SP8600 user manual — Using the security lock
Page 35 · click to enlarge
Page 35

4 Loosen the captive screws that attach the lamp housing to the projector.

5 Using the handle, carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner in accordance with local disposal laws.

InFocus SP8600 — Using the security lock diagram (page 35)
Fig. 42 · Using the security lock

6 Install the new lamp housing, pressing the lamp into place.

7 Tighten the captive screws.

8 Replace the lamp door and tighten both screws.

9 Plug in the power cord and press the Power button to turn the projector back on.

10 To reset the lamp hour timer, navigate to the Status and Service menu and select Reset Lamp Hours. See page 31 for details.

Using the security lock

The projector has a security lock for use with a Cable Lock System. Refer to the information that came with the lock for instructions on how to use it.

InFocus SP8600 — Using the security lock diagram (page 35)
Fig. 43 · Using the security lock
Page 36 of the InFocus SP8600 user manual — HDMI 1 HDMI 2
Page 36 · click to enlarge
Page 36

Appendix

SplitScreen Compatibility

Splitscreen allows two distinct sources to be displayed simultaneously. Switch primary sources, make picture adjustments and choose one of multiple display options: either two side by side horizontal or vertical source regions, or a small secondary source image displayed on top of the primary source in one of four placement options.lets you show two different sources at the same time. See page 27 for details. The following source combinations are supported:

Table 2:

VGA/ Component 4 Component 1 Component 2 Component 3 S-video Composite X

HDMI 1 HDMI 2

HDMI 1 HDMI 2 VGA/Component 4 Component 1 Component 2 Component 3 S-video Composite

Page 37 of the InFocus SP8600 user manual — RS-232 Commands
Page 37 · click to enlarge
Page 37

RS-232 Commands

AAA denotes the command ? denotes the read request ) ends the command

A read command returns the range and the current setting, for example:

Visit our website for additional RS-232 settings and information.

To control this projector via RS-232, connect a null modem cable and set the control system serial port settings to match the following communication configuration:

Brightness (BRT?) (0-100, 50)

Volume (VOL?) (0-100, 50)

Lamp Hours (LMP?) (0-32766, 42)

A write request example:

Bits per second 115,200

(AAA####) where (starts the command AAA denotes the command #### denotes the value to be written

(leading zeros not necessary)

) ends the command

Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically set to the maximum number for that function. If a command is received that is not understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on. The one exception is the Power command, where 0 is off and 1 is on.

All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read request (indicated by a"?") or a write request (indicated by 1 to 4 ASCII digits).

To assure the projector can process a command, wait 3 seconds before entering the next command.

A read request example:

(AAA?) where (starts the command

Show 11 more labels / short text on this page
Read Command Examples · Communication Configuration · Function Command Response · RS-232 Port Settings · Setting Value · Data bits 8 · Parity None · Stop bits 1 · Flow control None · Emulation VT100 · Command Format
Page 38 of the InFocus SP8600 user manual — ARZ RW 0 6 0 1
Page 38 · click to enlarge
Page 38

Com- mands RW Min Max Default Step

AC Power On 0Disable; 1: Enable APO RW 0 1 0 1

Brightness (BRT100) Sets the brightness to 100

SPS RW 0 2 0 1

Power (PWR0) Turns power off

Power (PWR1) Turns power on

Aspect Ratio 0Auto 1: Native 2: 4:3 3: 16:9 4: Letterbox 5: Panorama 6: 16:10

ARZ RW 0 6 0 1

Not all commands are supported for all projectors. If an unsupported command is issued, the command will be ignored. If a command is received that is not understood, a ‘?’ character will be returned indicating the commandwas not understood.

Aspect Ratio of Current Source ? = Query

QAR R source specific

The projector cannot respond to commands coming in at a high-rate. Therefore, a delay must occur between commands to ensure that the command gets properly executed. To assure the projector can process a command, wait 3 seconds before entering the next command.

Auto Image 1Enable AIM W n/a 1 1 1

Auto Off Time AOT RW 0 6 6 1

The Step column refers to increasing or decreasing the menu bar position since the On-screen Display is not an exact match of values. For example, Step 2 changes the data by 2 through the CLI (Command Line Interface). The menu bar is up (or down) by 1.

Auto Source 0Disable; 1: Enable ASC RW 0 1 1 1
Blank Screen 0Off; 1: On BLK RW 0 1 0 1
Show 6 more labels / short text on this page
Write Command Examples · Function · Function Commend Response · Always-On Functions · Error Conditions · Limitations
Page 39 of the InFocus SP8600 user manual — CSM RW 0 4 4 1
Page 39 · click to enlarge
Page 39

Blank Screen Style 0: Blue Screen 1: Timer 2: Test Pattern 3: Black Screen 4: White Screen 5: Factory Logo

BSS RW 0 5 0 1

Color Temp. 0Warmest 1: Warm 2: Cool 4: Bright

TMP RW 0 4 source specific 1

Contrast CON RW 0 100 50 1

Brightness BRT RW 0 100 50 1

Current Source Color Gamut ? = Query

QCG R source specific

BrilliantColor™ 0Normal; 1: Bright BCL RW 0 1 0 1

Current Source Color Space ? = Query

QCS R source specific

Ceiling Projection 0Disable; 1: Enable CEL RW 0 1 0 1
Closed Captions 0Off 1: CC1 2: CC2

CLC RW 0 2 0 1

Current Source Name ? = Query

QAS R source specific

Current Source Resolution ? = Query

RES R source specific

Color CLR RW 0 100 50 1

Color Gamut 0Auto 1: SMPTE_C 2: REC709 3: EBU 4: Maximum

CGA RW 0 4 0 1

Current Source Signal ? = Query

QST R source specific

Current Source Value ? = Query

QSF R source specific

Color Space 0RGB 1: REC709 2: REC601 3: RGB Video 4: Auto

CSM RW 0 4 4 1

Page 40 of the InFocus SP8600 user manual — ERR R 0 6 0 1
Page 40 · click to enlarge
Page 40

Custom Key 0: Blank Screen 3: Aspect Ratio 4: Source 5: Auto image 6: Freeze 8: Source Info 10: Projector Info 14: Overscan 16: Closed Captions 17: SplitScreen

EFK RW 0 17 8 1

Fast Color Refresh 0Off 1: Video only 2: On (all sources)

FCR RW 0 2 0 1

Firmware Version ? = Query

FVS R string 1

FTC RW 0 100 0 10

Force Wide 0Disable 1: Enable

FWM RW 0 1 1 1

Detect Film 0Disable 1: Enable

TTO RW 0 1 1 1

Freeze 0Disable 1: Enable

FRZ RW 0 1 0 1

DZM RW 0 100 100 10

Gamma 2Video 3: Film 5: Bright 7: CRT

GTB RW 0 7 source specific 1

DynamicBlack™ 0Auto 1: 100% 2: 90% 3: 80%... 10: 10%

DYB RW 0 10 1 1

Glow Ring 0Disable; 1: Enable GLO RW 0 1 1 1

Error Condition 0: No error 1: Lamp won’t strike after 5 attempts 3: Lamp went out unexpectedly 4: Fan Failure 5: Over temperature 6: Low voltage

ERR R 0 6 0 1

Help Command 0Disable; 1: Enable HLP RW 0 1 0 1

Horz. Keystone DKH RW 0 100 50 1

Horz. Pincushion HPC RW 0 100 50 1

Horz. Position HPS RW 0 100 50 1

Horz. Refresh Frequency ? = Query

Factory Reset 1reset RST W n/a 1 1 1
Show 4 more labels / short text on this page
Flesh Tone Correction · Digital Zoom Setting · QHR R string · ? = Query
Page 41 of the InFocus SP8600 user manual — MNL RW 0 15 0
Page 41 · click to enlarge
Page 41

Horz. Shift DSH RW 0 100 50 1

Language 0: English 1: French 2: German 3: Italian 5: Korean 6: Norwegian 7: Portuguese 8: Russian 9: Simp Chinese 10: Spanish 11: Trad Chinese 12: Swedish 13: Dutch 14: Polish 15: Turkish 16: Danish 17: Finnish

LAN RW 0 17 0 (9 for China models)

Key Click 0Disable; 1: Enable KCL RW 0 1 1
Keypad Enable 0Disable; 1: Enable KPE RW 0 1 1 1

Lamp Hours in High Power Mode ? = Query

LMO R 0 n/a 1

Lamp Hours in Low Power Mode ? = Query

LME R 0 n/a 1

Lamp Life ? = Query

LIF R n/a 2000

Lamp Low Power 0Disable; 1: Enable IPM RW 0 1 1 1
Magnify Controls 0Disable; 1: Enable MGC RW 0 1 1 1

Lamp Resets (Total number) ? = Query

LMR R 0 n/a 1

Magnify Horz. Position

MGH RW 0 100 50 5

Lamp Total On Time (All Bulbs) ? = Query

LMT R 0 n/a 1

Magnify Level MGL RW 0 100 0 5

Magnify Vert. Position

MGV RW 0 100 50 5

Lamp Total High Power Time (All Bulbs) ? = Query

LTO R 0 n/a 1

Menu 0Clear; 1: Display MNU RW 0 1 0 1

Menu Lockout 1: Basic Picture 2: Adv Picture 4: Setup Menu 8: Status & Service 15: All Menus

MNL RW 0 15 0

Lamp Total Low Power Time (All Bulbs) ? = Query

LTE R 0 n/a 1

Page 42 of the InFocus SP8600 user manual — PWR RW 0 1 0 1
Page 42 · click to enlarge
Page 42

Menu Navigation 0: Menu Key 1: Up Key 2: Down Key 3: Select Key 4: Left Key 5: Right Key

NAV W 0 5 n/a 1

Power Sounds 0Disable; 1: Enable ACE RW 0 1 1 1

Power-up Source 0: VGA 1: HDMI1 2: HDMI 2 3: Component 1 4: Component 2 5: Component 3 6: S-video 7: Composite

DSC RW 0 7 1 1

Menu Offset OFF RW 0 100 0 10

Menu Transparency 0: Opaque 20: 20% Trans.

TOE RW 0 90 20 5

Presets 1: User 5: Presentation 7: Video 8: ISF Day 9: ISF Night 10: Bright 11: Whiteboard 12: Blackboard 13: Beige Wall

PST RW 1 13 source specific 1

Motion Smoothing 0Disable 1: Low 2: Normal 3: High 4: Demo

MSM RW 0 4 0 1

Native Resolution ? = Query

Noise Reduction NRL RW 0 100 50 1

Prevent PC Screen Saver 0Disable; 1: Enable

NND RW 0 1 1 1

Overscan 0disable 1: zoom 2: crop

OVS W 0 2 0 1

Projector Info menu 1Display PRI W 1 1

Phase MSS RW 0 100 50 1

Projector Model ? = Query

Pixel Clock Freq. ? = Query

Projector Serial No. ? = Query

Power 0Turn Off 1: Turn On

PWR RW 0 1 0 1

Rear Projection 0Disable; 1: Enable REA RW 0 1 0 1
Show 4 more labels / short text on this page
NRS R string · MDL R string · QPC R string · USN R string
Page 43 of the InFocus SP8600 user manual — BLC W 1 1
Page 43 · click to enlarge
Page 43
Reset Lamp Hours 1Reset LRT W n/a 1 1 1
Sharpness 0Maximum 1: High 2: Normal 3: Low 4: Minimum

SHP RW 0 4 2 1

Save User Presets 1Save US1 W n/a 1 1 1

Screen Save 0: Never 1: 5 minutes 2: 10 minutes 3: 15 minutes 4: 20 minutes 5: 25 minutes 6: 30 minutes

SSV RW 0 6 0 1

Show Messages 0Disable; 1: Enable DMG RW 0 1 0 1
SleepTimer 0Off 1: 2 hours 2: 4 hours 3: 6 hours

SLT RW 0 3 0 1

Search Screen 0Factory Logo 1: Blue 3: Black 4: White

DSU RW 0 4 0 1

Source 0: VGA 1: HDMI1 2: HDMI 2 3: Component 1 4: Component 2 5: Component 3 6: S-video 7: Composite

SRC RW 0 7 1 1

Serial Port Baud Rate 0: 2400 1: 4800 2: 9600 3: 14400 4: 19200 5: 38400 6: 57600 7: 115200 8: 1200

BR1 RW 0 8 7 1

Source Adv. PC CAD+ W +

Source Adv. Video VAD+ W +

Source Info menu 1Display ABT W n/a 1 1 1
Serial Port Echo 0Disable; 1: Enable EC1 RW 0 1 0

Source Name (0-7) * = Factory Names SNn RW string

Source 1-4 Commands SR1 = Source Key 1 SR2 = Source Key 2

SRn RW SR1 = VGA SR2 = HDMI 1 SR3 = HDMI 2

Set Black Level Command 1Execute

BLC W 1 1

Page 44 of the InFocus SP8600 user manual — RCO GCO BCO
Page 44 · click to enlarge
Page 44
SplitScreen Enable 0off; 1: on SSC RW 0 1 0 1

System State 1: Off 2: Start Up 4: Search 7: Source Displayed 9: Blank Screen 12: Cool Down 13: Screen Save 17: Flash Update 18: Error

SYS R 1 18 7 1

SplitScreen 2nd Source 0:off 1: VGA 2: HDMI1 3: HDMI 2 4: Component 1 5: Component 2 6: Component 3 7: S-video 8: Composite

SSL RW 0 8 source specific - See User Guide SplitScreen Matrix in Appendix

Test Pattern Select TPS RW 0 21 9 1

Tint TNT RW 0 100 50 1

Total Lamp Hours ? = Query

LMP R 0 n/a 1

SplitScreen 2nd Source Location 0: right 1: bottom 2: left 3: top 4: PiP bottom right 5: PiP bottom left 6: PiP top left 7: PiP top right

SSY RW 0 7 0 1

Tracking MTS RW 0 100 50 1

Vert. Keystone DKV RW 0 100 50 1

Vert. Pincushion VPC RW 0 100 50 1

Vert. Position VPS RW 0 100 50 1

Vert. Refresh Freq. ? = Query

SplitScreen 2nd Source Size 0small; 1: medium 2: large

SSZ RW 0 2 2 1

Vert. Shift DSV RW 0 100 50 1

Video Standard 0Auto; 1: NTSC 2: PAL; 5: SECAM

VSU RW 0 5 0 1

SplitScreen Swap 1enable SSS W n/a 1 1 1

Red Gain Green Gain Blue Gain

RCG GCG BCG

RW 0 100 50 1

Sync Threshold STH RW 0 100 50 10

Red Offset Green Offset Blue Offset

RCO GCO BCO

RW 0 100 50 1

QVR R string

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No start up screenPlug power cord into the projector, then press power button p.17
No start up screen p.17
Only start up screen appears SS eta rtu np A c rePress the Source button Activate the laptop’s external port Restart laptop p.17
Only start up screen appears SS eta rtu np A c re p.17
No computer image, just the words “Signal out of range” rangeSignal out of A thePress the Auto Image button on the keypad or on the remote. To adjust computer refresh rate, go to Control Panel > Display > Settings > Advanced > Adapter (location varies by operating system). You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped” p.18
No computer image, just the words “Signal out of range” rangeSignal out of A the p.18
Only my laptop’s background appears, not the Desktop icons AWindows - Disable “Extend my Windows Desktop” in Control Panel > Display > Settings > Display 2 (location varies by operating system) Uncheck this option, then click Apply p.18
Only my laptop’s background appears, not the Desktop icons A p.18
Image fuzzy or cropped A ASet your computer’s display resolution to the native resolution of the projector (Start > Settings > Control Panel > Display > Settings tab) For a laptop, disable laptop monitor or turn- on dual-display mode p.19
Image not centered on screenMove projector, adjust zoom and lens shift horizontal zoomfocus vertical p.19
Image not squareAdjust Keystone in the Basic Picture menu p.20
Image not sharpAdjust Sharpness in the Basic Picture menu p.20
Image does not fit 4:3 or 16:9 screenChange aspect ratio to 4:3 or 16:9 in Basic Picture>Aspect Ratio menu p.20
Image upside down ATurn off Ceiling Mount in Setup menu p.21
Image reversed left to right ATurn off Rear Project in Setup menu p.21
Projected colors don’t match source COLORAdjust color, tint, brightness, contrast in the Basic Picture menu and/or color space in the Advanced Picture menu p.21
The video embedded in my PowerPoint presentation does not play on the screen A BTurn off the internal LCD display on your laptop p.22
The video embedded in my PowerPoint presentation does not play on the screen A B p.22
Lamp won’t turn on, Temperature light is on Temperature lightMake sure vents aren’t blocked, turn the projector off and allow it to cool for one minute. p.22
Lamp won’t turn on, Temperature light is on Temperature light p.22
“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on Lamp lightLamp must be replaced (see page 33) Replace lamp Lamp door p.23

Ask about the InFocus SP8600

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus SP8600

Be the first to ask — other owners or our team will answer.

Original document

InFocus SP8600 manual PDF

45 pages·9.5 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…