EN
InFocus logo
Official user manual

InFocus SP8600

51 pages·5 MB·Projector·PDF·ENDEFRITNLJA
InFocus SP8600
Table of Contents 62 sections Getting Started · Packing Checklist · Views of Projector Parts · Front-right View · … ShowHide
Page 1 of the InFocus SP8600 user manual
Page 1 · click to enlarge
Page 1
InFocus SP8600 diagram (page 1)
Fig. 1
InFocus SP8600 diagram (page 1)
Fig. 2
Page 2 of the InFocus SP8600 user manual — Trademark Recognition
Page 2 · click to enlarge
Page 2

Copyright

This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no repre- sentations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pend- ing applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

All other product names used in this manual are the properties of their respective owners and are ac- knowledged.

© Copyright 2010

Page 3 of the InFocus SP8600 user manual — General Safety Information
Page 3 · click to enlarge
Page 3

Important Safety Information

Symbols Used

The following styles are used in this manual to alert you to important information.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example: “Push the MENU button on the remote control to open the DISPLAY menu.”

General Safety Information

¾ Do not open the projector. Aside from the projection lamp, there are no user-serviceable parts in

the projector. For servicing, contact qualified service personnel.

¾ Follow all warnings and cautions in this manual and on the projector.

¾ The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the

lens when the lamp is on.

¾ Do not place the projector on an unstable surface, cart, or stand.

¾ Avoid using the system near water, in direct sunlight, or near a heating device.

¾ Do not place heavy objects such as books or bags on the projector.

Page 4 of the InFocus SP8600 user manual — Power Safety
Page 4 · click to enlarge
Page 4

Preface

Projector Installation Notice

¾ Place the projector in a horizontal position

The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.

InFocus SP8600 — Preface diagram (page 4)
Fig. 3 · Preface
InFocus SP8600 — Preface diagram (page 4)
Fig. 4 · Preface
InFocus SP8600 — Preface diagram (page 4)
Fig. 5 · Preface

¾ Allow at least 50 cm clearance around the exhaust vent.

InFocus SP8600 — Preface diagram (page 4)
Fig. 6 · Preface
InFocus SP8600 — Preface diagram (page 4)
Fig. 7 · Preface
InFocus SP8600 — Preface diagram (page 4)
Fig. 8 · Preface
InFocus SP8600 — Preface diagram (page 4)
Fig. 9 · Preface
InFocus SP8600 — Preface diagram (page 4)
Fig. 10 · Preface

¾ Ensure that the intake vents do not recycle hot air from the exhaust vent.

¾ When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed 5 – 35°C while the projector is running, and the air intake and exhaust vents are unobstructed.

¾ All enclosures should pass a certified thermal evaluation to ensure that the projector does not

recycle exhaust air, as this may cause the device to shut down even if the enclosure temperature is within the acceptable 5 – 35°C range.

Power Safety

¾ Only use the supplied power cord.

¾ Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

¾ Remove the batteries from the remote control when storing or not in use for a prolonged period.

– iii –

Page 5 of the InFocus SP8600 user manual — About this manual
Page 5 · click to enlarge
Page 5

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 29 for clear and safe instructions for this procedure. Before replacing the lamp:

¾ Unplug the power cord.

¾ Allow the lamp to cool for about one hour.

Cleaning the Projector

¾ Unplug the power cord before cleaning. See Cleaning the Projector on page 32.

¾ Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section on page 44.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at www.eiae.org For lamp specific disposal information check www.lamprecycle.org

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.

Main Features

  • Lightweight projector, easy to pack away and transport.
  • Compatible with all major video standards including NTSC, PAL, and SECAM.
  • A high brightness rating allows for presentations in daylight or in lit rooms.
  • Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images.
  • Flexible setup allows for front, rear projections.
  • Line-of-vision projections remain square, with advanced keystone correction for angled projections.
  • Input source automatically detected.

About this manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wher- ever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.

Page 6 of the InFocus SP8600 user manual — Table of contents
Page 6 · click to enlarge
Page 6

Table of contents

Getting Startedp.8Packing Checklistp.8Views of Projector Partsp.9Front-right Viewp.9Top view—On-screen Display (OSD) buttons and LEDsp.10Rear viewp.11Bottom viewp.12Remote Control Partsp.13Remote Control Operating Rangep.15Projector and Remote Control Buttonsp.15Setup and Operationp.16Inserting the Remote Control Batteriesp.16Connecting Input Devicesp.17Starting and Shutting down the Projectorp.18Adjusting the Projector Levelp.19Adjusting the Zoom ring, Focus and Keystonep.20Adjusting the Volumep.21On-Screen Display (OSD) Menu Settingsp.22OSD Menu Controlsp.22Navigating the OSDp.22Setting the OSD Languagep.23OSD Menu Overviewp.24PICTURE>>Basic Menup.25PICTURE>>Advanced Menup.26HSG Adjustmentp.27DISPLAY Menup.28PC Detail Adjustmentp.29SETUP>>Basic Menup.30Menu Settingsp.31Sourcep.31SETUP>>Advanced Menup.32Audiop.33Lampp.33HDMIp.34Closed Captionp.34STATUS Menup.35Maintenance and Securityp.36Replacing the Projection Lampp.36Cleaning the Projectorp.39Cleaning the Lensp.39Cleaning the Casep.39Using the Kensington® Lockp.40Troubleshootingp.41Common problems and solutionsp.41Tips for Troubleshootingp.41LED Error Messagesp.42Image Problemsp.42Lamp Problemsp.43Remote Control Problemsp.43Audio Problemsp.44Need Assistance?p.44HDMI Q & Ap.45Specificationsp.46Specificationsp.46Projection Distance vs. Projection Sizep.47Projection Distance and Size Tablep.47Timing Mode Tablep.48Projector Dimensionsp.50Regulatory Compliancep.51FCC Warningp.51Canadap.51Safety Certificationsp.51
Page 7 of the InFocus SP8600 user manual — Table of contents
Page 7 · click to enlarge
Page 7

Table of contents

Getting Startedp.8Packing Checklistp.8Views of Projector Partsp.9Front-right Viewp.9Top view—On-screen Display (OSD) buttons and LEDsp.10Rear viewp.11Bottom viewp.12Remote Control Partsp.13Remote Control Operating Rangep.15Projector and Remote Control Buttonsp.15Setup and Operationp.16Inserting the Remote Control Batteriesp.16Connecting Input Devicesp.17Starting and Shutting down the Projectorp.18Adjusting the Projector Levelp.19Adjusting the Zoom ring, Focus and Keystonep.20Adjusting the Volumep.21On-Screen Display (OSD) Menu Settingsp.22OSD Menu Controlsp.22Navigating the OSDp.22Setting the OSD Languagep.23OSD Menu Overviewp.24PICTURE>>Basic Menup.25PICTURE>>Advanced Menup.26HSG Adjustmentp.27DISPLAY Menup.28PC Detail Adjustmentp.29SETUP>>Basic Menup.30Menu Settingsp.31Sourcep.31SETUP>>Advanced Menup.32Audiop.33Lampp.33HDMIp.34Closed Captionp.34STATUS Menup.35Maintenance and Securityp.36Replacing the Projection Lampp.36Cleaning the Projectorp.39Cleaning the Lensp.39Cleaning the Casep.39Using the Kensington® Lockp.40Troubleshootingp.41Common problems and solutionsp.41Tips for Troubleshootingp.41LED Error Messagesp.42Image Problemsp.42Lamp Problemsp.43Remote Control Problemsp.43Audio Problemsp.44Need Assistance?p.44HDMI Q & Ap.45Specificationsp.46Specificationsp.46Projection Distance vs. Projection Sizep.47Projection Distance and Size Tablep.47Timing Mode Tablep.48Projector Dimensionsp.50Regulatory Compliancep.51FCC Warningp.51Canadap.51Safety Certificationsp.51
Page 8 of the InFocus SP8600 user manual — S AFETY B OOKLET R EGISTRATION C ARD
Page 8 · click to enlarge
Page 8

G ETTING S TARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

InFocus SP8600 — Packing Checklist diagram (page 8)
Fig. 11 · Packing Checklist

DLP P ROJECTOR

InFocus SP8600 — DLP P ROJECTOR diagram (page 8)
Fig. 12

R EMOTE CONTROL ( BATTERY NOT INCLUDED )

HDMI CABLE POWER CORD (EU) POWER CORD (UK)

POWER CORD (US) CD-ROM (THIS USER’S MANUAL)

QUICK START CARD WARRANTY CARD

S AFETY B OOKLET R EGISTRATION C ARD

Contact your dealer immediately if any items are missing, appear damaged, or if the projector does not work. It is recommended that you keep the original packing material should you ever need to return the equipment for warranty service.

Safety Booklet

Page 9 of the InFocus SP8600 user manual — I TEM L ABEL D ESCRIPTION S EE PAGE :
Page 9 · click to enlarge
Page 9

Views of Projector Parts

Front-right View

InFocus SP8600 — Views of Projector Parts diagram (page 9)
Fig. 13 · Views of Projector Parts

1 3 4 5 6 7 2

InFocus SP8600 — 1 3 4 5 6 7 2 diagram (page 9)
Fig. 14

I TEM L ABEL D ESCRIPTION S EE PAGE :

4. IR receiver Receive IR signal from remote control 6
7. Function keys See Top view—On-screen Display (OSD) buttons and LEDs. 3
Page 10 of the InFocus SP8600 user manual — I TEM L ABEL D ESCRIPTION S EE PAGE :
Page 10 · click to enlarge
Page 10

Top view—On-screen Display (OSD) buttons and LEDs

InFocus SP8600 — Top view—On-screen Display (OSD) buttons and LEDs diagram (page 10)
Fig. 15 · Top view—On-screen Display (OSD) buttons and LEDs
InFocus SP8600 — Top view—On-screen Display (OSD) buttons and LEDs diagram (page 10)
Fig. 16 · Top view—On-screen Display (OSD) buttons and LEDs

I TEM L ABEL D ESCRIPTION S EE PAGE :

Red Lamp is ready to be powered-on. 2. Lamp LED Lamp is not ready (warming up/shutting down/cooling) (see Flashing LED Error Messages on page 35) 3. Temp LED Flashing Error code

11 4. Turn the projector On or Off. (Power button) ▲ (Up cursor) / Navigate and change settings in the OSD Quick Menu – For Keystone 5. Keystone

Navigate and change settings in the OSD Quick Menu – For Volume 7.

▼ (Down cursor) / Navigate and change settings in the OSD Quick Menu – For Keystone 9. Keystone

10. ENTER Enter or confirm highlighted OSD menu item 15

Navigate and change settings in the OSD Quick Menu – For Volume 11.

Page 11 of the InFocus SP8600 user manual — 11 12 13 14 15 16
Page 11 · click to enlarge
Page 11

Rear view

1 2 3 4 5 6 7 8 9 10

InFocus SP8600 — 1 2 3 4 5 6 7 8 9 10 diagram (page 11)
Fig. 17

11 12 13 14 15 16

ITEMLABELDESCRIPTIONSEE PAGE: 1.AC INConnect the power cord11 2.(USB)Connect a USB cable from a computer10 3.COMPONENTConnect a component video enabled device 4.S-VIDEOConnect a S-VIDEO cable from a video device 5.COMPOSITEConnect a COMPOSITE cable from a video device 6.VGAConnect a RGB cable from a computer. 7.HDMI – 1Connect a HDMI cable from a HDMI device 8.HDMI – 2 9.SCREEN TRIGGERWhen connected to the screen through a commercially available cable, the screen deploys automatically on start up of the projector. The screen retracts when the projector is powered off. 10.Kensington LockSecure to permanent object with a Kensington® Lock system33 11.SpeakerOutputs audio sound10 12.IR receiverReceive IR signal from remote control6 13.AUDIO (L and R)Connect the audio cables from an audio device10 14.AUDIOConnect an audio cable from the input device 15.SERIALConnect a serial port cable for remote control 16.AUDIO OUTConnect an audio cable for audio loop through
Page 12 of the InFocus SP8600 user manual — Bottom view
Page 12 · click to enlarge
Page 12

Bottom view

Ceiling Mount

2 1 3 4 2

InFocus SP8600 — Bottom view diagram (page 12)
Fig. 18 · Bottom view
InFocus SP8600 — Bottom view diagram (page 12)
Fig. 19 · Bottom view
ITEMLABELDESCRIPTIONSEE PAGE: 1.Tilt adjustor Rotate adjuster lever to adjust angle position.12 2.Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 3.Height adjustor Adjuster drops down when adjuster button is pushed.12 4.Height adjustor button Push to release adjustor.
InFocus SP8600 — Bottom view diagram (page 12)
Fig. 20 · Bottom view

Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 12 mm (0.47 inch). The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a period of 60 seconds.

M4x8 (Max L=12mm)

Page 13 of the InFocus SP8600 user manual — Remote Control Parts
Page 13 · click to enlarge
Page 13

Remote Control Parts

InFocus SP8600 — Remote Control Parts diagram (page 13)
Fig. 21 · Remote Control Parts
InFocus SP8600 — Remote Control Parts diagram (page 13)
Fig. 22 · Remote Control Parts

Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control. This user’s manual describes the functions based on the remote control.

Page 14 of the InFocus SP8600 user manual — I TEM L ABEL D ESCRIPTION S EE PAGE :
Page 14 · click to enlarge
Page 14

I TEM L ABEL D ESCRIPTION S EE PAGE :

1. Up cursor Navigate and change settings in the OSD
2. Enter Change settings in the OSD
3. Power Turn the projector On or Off 11
4. Right cursor Navigate and change settings in the OSD 15
5. Volume + Increase volume
6. Volume - Decrease volume
7. Mute Mute the built-in speaker
8. Freeze Freeze/unfreeze the on-screen picture
9. Source Select the desired video input 10
10. Auto Auto adjustment for frequency, tracking, size, position (RGB only)
11. Keystone top Correct image-trapezoid (wider top) effect
12. Keystone bottom Correct image trapezoid (wider bottom) effect
13. Down cursor Navigate and change settings in the OSD
14. Left cursor Navigate and change settings in the OSD
15. Menu Open the OSD
Page 15 of the InFocus SP8600 user manual — Projector and Remote Control Buttons
Page 15 · click to enlarge
Page 15

Remote Control Operating Range

The projector receives infrared signals from the remote control. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however, the buttons on the projector are lim- ited in use.

Page 16 of the InFocus SP8600 user manual — Inserting the Remote Control Batteries
Page 16 · click to enlarge
Page 16

S ETUP AND O PERATION

Inserting the Remote Control Batteries

InFocus SP8600 — Inserting the Remote Control Batteries diagram (page 16)
Fig. 23 · Inserting the Remote Control Batteries
1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover (B) .
2. Insert the battery (not included) with the positive side facing up.
3. Replace the cover.
InFocus SP8600 — Inserting the Remote Control Batteries diagram (page 16)
Fig. 24 · Inserting the Remote Control Batteries
Page 17 of the InFocus SP8600 user manual — H
Page 17 · click to enlarge
Page 17

Connecting Input Devices

A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.

H

L K J

ITEM LABEL DESCRIPTION A Connect a USB cable from a computer (USB) B COMPONENT Connect a component video enabled device C S-VIDEO Connect a S-VIDEO cable from a video device D COMPOSITE Connect a COMPOSITE cable from a video device E VGA Connect a RGB cable from a computer. F HDMI – 1 Connect a HDMI cable from a HDMI device G HDMI – 2

When connected to the screen through a commercially available cable, the screen deploys automatically on start up of the projector. The screen retracts when the projector is powered off. H SCREEN TRIGGER

I AUDIO (L and R) Connect audio cables from an audio device J AUDIO Connect an audio cable from the input device K SERIAL Connect a serial port cable for remote control L AUDIO OUT Connect an audio cable for audio loop through

Page 18 of the InFocus SP8600 user manual — Starting and Shutting down the Projector
Page 18 · click to enlarge
Page 18

Starting and Shutting down the Projector

1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED will be on.
2. Turn on the connected devices.
InFocus SP8600 — Starting and Shutting down the Projector diagram (page 18)
Fig. 25 · Starting and Shutting down the Projector

Ensure the POWER LED displays a solid green and not a flashing green. Then press the POWER button to turn on the projector. The projector splash screen displays and connected devices are detected.

InFocus SP8600 — Starting and Shutting down the Projector diagram (page 18)
Fig. 26 · Starting and Shutting down the Projector
4. If more than one input device is connected, press the SOURCE button to switch among devices.
  • PC: Analog RGB
  • HDMI 1/2: High Definition Multimedia Interface
  • Component: DVD input YCbCr / YPbPr
  • S-Video: Super video (Y/C separated)
  • Composite: Traditional composite video
InFocus SP8600 — Starting and Shutting down the Projector diagram (page 18)
Fig. 27 · Starting and Shutting down the Projector

When the POWER OFF window ap- pears, press

on the control panel or Power on the remote control. The pro- jector turns off.

Page 19 of the InFocus SP8600 user manual — Adjusting the Projector Level
Page 19 · click to enlarge
Page 19

Adjusting the Projector Level

Take note of the following when setting up the projector:

  • The projector table or stand should be level and sturdy.
  • Position the projector so that it is perpendicular to the screen.
  • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle.
  • Ensure the cables are in a safe location. You could trip over them.
InFocus SP8600 — Adjusting the Projector Level diagram (page 19)
Fig. 28 · Adjusting the Projector Level
1. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B] .

The height adjuster drops down [C].

2. To lower the level of the projector, press the height-adjuster button and push down on the top of the projector.
3. To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the desired angle has been achieved.
Page 20 of the InFocus SP8600 user manual — Adjusting the Zoom ring, Focus and Keystone
Page 20 · click to enlarge
Page 20
InFocus SP8600 — Adjusting the Zoom ring, Focus and Keystone diagram (page 20)
Fig. 29 · Adjusting the Zoom ring, Focus and Keystone
1. Use the Image-zoom control (on the projector only) to resize the projected image and screen size B .
2. Use the Image-focus control (on the projector only) to sharpen the projected image . A

Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect.

4. The keystone control appears on the display.
Page 21 of the InFocus SP8600 user manual — Adjusting the Volume
Page 21 · click to enlarge
Page 21

Adjusting the Volume

Press the Volume +/- buttons on the remote control. The volume control appears on the display.

2. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/- .
3. Press the MUTE button to turn off the volume (This feature is available only on the remote).
Show 4 more labels / short text on this page
Menu · Source · Re-sync · Enter
Page 22 of the InFocus SP8600 user manual — Navigating the OSD
Page 22 · click to enlarge
Page 22

O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS

OSD Menu Controls

The projector has an OSD that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector.

InFocus SP8600 — Navigating the OSD diagram (page 22)
Fig. 30 · Navigating the OSD
InFocus SP8600 — Navigating the OSD diagram (page 22)
Fig. 31 · Navigating the OSD
1. To enter the OSD, press the MENU button.
InFocus SP8600 — Navigating the OSD diagram (page 22)
Fig. 32 · Navigating the OSD
2. There are six menus. Press the cursor ◄► button to move through the menus.
3. Press the cursor ▲▼ button to move up and down in a menu.
4. Press ◄► to change values for settings.
5. Press MENU to close the OSD or leave a sub menu.
InFocus SP8600 — Navigating the OSD diagram (page 22)
Fig. 33 · Navigating the OSD

2 / 7 · 3 / 5 · 2 / 7

Page 23 of the InFocus SP8600 user manual — Setting the OSD Language
Page 23 · click to enlarge
Page 23

Setting the OSD Language

Set the OSD language to your preference before continuing.

1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic .
InFocus SP8600 — Setting the OSD Language diagram (page 23)
Fig. 34 · Setting the OSD Language
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ◄► button until the language you want is selected.
4. Press the MENU button to close the OSD.
Page 24 of the InFocus SP8600 user manual — OSD Menu Overview
Page 24 · click to enlarge
Page 24

OSD Menu Overview

Use the following illustration to quickly find a setting or determine the range for a setting.

InFocus SP8600 — OSD Menu Overview diagram (page 24)
Fig. 35 · OSD Menu Overview
InFocus SP8600 — OSD Menu Overview diagram (page 24)
Fig. 36 · OSD Menu Overview
Page 25 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 25 · click to enlarge
Page 25

PICTURE>>Basic Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu. Press ◄► to change values for settings.

InFocus SP8600 — PICTURE>>Basic Menu diagram (page 25)
Fig. 37 · PICTURE>>Basic Menu

I TEM D ESCRIPTION

Press the cursor ◄► buttons to set the Display Mode. (Range: Movie/ Bright/ Normal/ User 1/ User 2/ User 3) Display Mode

Press the cursor ◄► buttons to set the User Mode. (Range: Movie/ Bright / Normal) User Mode

Brightness Press the cursor ◄► buttons to adjust the display brightness.

Contrast Press the cursor ◄► buttons to adjust the display contrast.

Press the cursor ◄► buttons to adjust the video saturation. Color Notes: This function is only available when Component, Composite or S-Video input

source is selected.

Press the cursor ◄► buttons to adjust the video tint/hue. Tint Notes: This function is only available when Component, Composite or S-Video with

NTSC system input source is selected.

Press the cursor ◄► buttons to adjust the display sharpness. Sharpness Notes: This function is only available when Component, Composite or S-Video input

source is selected.

Press the cursor ◄► buttons to adjust the display flesh tone. Flesh Tone Notes: This function is only available when Component, Composite or S-Video input

source is selected.

Press the ENTER button to save all settings. Save Setting

Press the ENTER button to reset all settings to default values. Reset Picture Settings

Page 26 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 26 · click to enlarge
Page 26

PICTURE>>Advanced Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings.

InFocus SP8600 — PICTURE>>Advanced Menu diagram (page 26)
Fig. 38 · PICTURE>>Advanced Menu

I TEM D ESCRIPTION

Noise Reduction Press the cursor ◄► button to adjust the Noise Reduction.

Color Temperature Press the cursor ◄► button to set the Color Temperature.

Press the cursor ◄► button to adjust the gamma correction of the display. Notes: This function is only available in User 1/ 2/ 3 mode. Gamma

Press the ENTER button to enter the HSG Adjustment sub menu. See HSG Adjustment HSG Adjustment on page 20.

Press the cursor ◄► button to set the Color Space. (Range: Auto/ RGB/ SDTV/ HDTV) Notes: This function is only available when HDMI input source is selected. Color Space

Page 27 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 27 · click to enlarge
Page 27

HSG Adjustment

Press the ENTER button to enter the HSG Adjustment sub menu.

InFocus SP8600 — HSG Adjustment diagram (page 27)
Fig. 39 · HSG Adjustment

I TEM D ESCRIPTION

Press the ◄► buttons to set the Primary Color. Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized. Primary Color

Hue Press the ◄► buttons to adjust the Hue.

Saturation Press the ◄► buttons to adjust the Saturation.

Gain Press the ◄► buttons to adjust the Gain.

Page 28 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 28 · click to enlarge
Page 28

DISPLAY Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings.

InFocus SP8600 — DISPLAY Menu diagram (page 28)
Fig. 40 · DISPLAY Menu

I TEM D ESCRIPTION

Press the cursor ◄► button to set the Aspect Ratio. (Range: Auto/ 16:9/ 4:3/ Letter Box/ Real) Aspect Ratio

Press the cursor ◄► button to adjust the Keystone. Notes: This function is available when the Auto keystone function is turned off. Keystone

Overscan Press the cursor ◄► button to adjust the Overscan.

Press the ENTER button to enter the PC Detail Adjustment sub menu. See PC Detail Adjustment PC Detail Adjustment on page 22.

Press the cursor ◄► button to turn on or off the Auto Keystone. Notes: When Auto Keystone is on, the projector will automatically adjust the Keystone. Auto Keystone

Page 29 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 29 · click to enlarge
Page 29

PC Detail Adjustment

Press the ENTER button to enter the PC Detail Adjustment sub menu.

InFocus SP8600 — PC Detail Adjustment diagram (page 29)
Fig. 41 · PC Detail Adjustment

I TEM D ESCRIPTION

Press the ENTER/AUTO button on the control panel or the ENTER/AUTO button on the remote control to automatically adjust frequency, phase, and position. Auto

Frequency Press the ◄► buttons to adjust the A/D sampling number.

Phase Press the ◄► buttons to adjust the A/D sampling clock.

Horizontal Position Press the ◄► buttons to adjust the display position right or left.

Vertical Position Press the ◄► buttons to adjust the display position up or down.

Page 30 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 30 · click to enlarge
Page 30

SETUP>>Basic Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings.

I TEM D ESCRIPTION

Language Press the cursor ◄► buttons to select a different localization menu.

Press the cursor ◄► buttons to select a different startup screen. (Range: InFocus/ Blue/ Black) Splash Logo

Press the cursor ◄► buttons to choose from four projection methods: Front Table/ Front Ceiling/ Rear Table/ Rear Ceiling. Projection

Press the cursor ◄► buttons to set the Blank Screen timer. The projected image is automati- cally restored after the set time. (Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min) Blank Timer

Press the cursor ◄► buttons to set the Auto Power Off timer. The projector automatically turns off if no input source is detected after the preset period of time. (Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min) Auto Power Off

Press the cursor ◄► buttons to set Sleep timer. The projector automatically turns off after the preset period of time. (Range: Disable/ 30 min/ 1hr/ 2hr/ 3hr/ 4hr/ 8hr/ 12hr) Sleep Timer

Press the cursor ◄► buttons to select the background color when no input source is detected. (Range: Purple/ Black/ Blue) Background Color

Press the ENTER button to enter the Menu Settings sub menu. See Menu Settings Menu Settings on page 24.

Source Press the ENTER button to enter the Source sub menu. See Source on page 24.

Page 31 of the InFocus SP8600 user manual — HDMI 1
Page 31 · click to enlarge
Page 31

Menu Settings

Press the ENTER button to enter the Menu Settings sub menu.

InFocus SP8600 — Menu Settings diagram (page 31)
Fig. 42 · Menu Settings

I TEM D ESCRIPTION

Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center/ Bottom-Left/ Bottom-Right. Menu Position

Press the ◄► buttons to set the Menu Display timer before the OSD times out. (Range: 5sec/ 10sec/ 15sec/ 20sec/ 25sec/ 30sec) Menu Display Time

Source

Press the ENTER button to enter the Source sub menu.

InFocus SP8600 — Source diagram (page 31)
Fig. 43 · Source

I TEM D ESCRIPTION

PC Press the ◄► buttons to enable or disable the PC source.

HDMI 1

Press the ◄► buttons to enable or disable the HDMI source. HDMI 2

Component Press the ◄► buttons to enable or disable the Component source.

Composite Press the ◄► buttons to enable or disable the Video source.

S-Video Press the ◄► buttons to enable or disable the S-Video source.

Press the ◄► buttons to enable or disable Quick Auto Search for available input source. Notes: When the desired source is selected, the Quick Auto Search function will be turn off. Quick Auto Search

Page 32 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 32 · click to enlarge
Page 32

SETUP>>Advanced Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu.

InFocus SP8600 — SETUP>>Advanced Menu diagram (page 32)
Fig. 44 · SETUP>>Advanced Menu

I TEM D ESCRIPTION

Audio Press the ENTER button to enter the Audio sub menu. See Audio on page 26.

Lamp Press the ENTER button to enter the Lamp sub menu. See Lamp on page 26.

HDMI Press the ENTER button to enter the HDMI sub menu. See HDMI on page 27.

Press the cursor ◄► buttons to turn on or off High Altitude Mode when the altitude of the environment is higher than 1500m, or the temperature is over 40°C. High Altitude Mode

Test Pattern Press the cursor ◄► buttons to turn on or off the grid test pattern.

Press the ENTER button to enter the Closed Caption sub menu. See Closed Caption Closed Caption on page 27.

Press the cursor ◄► buttons to select the LED control. Select Normal for normal LED display and Off to disable LED display. LED Control

Press the ENTER button to enter reset all settings to default values. Reset All

Page 33 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 33 · click to enlarge
Page 33

Audio

Press the ENTER button to enter the Audio sub menu.

InFocus SP8600 — Audio diagram (page 33)
Fig. 45 · Audio

I TEM D ESCRIPTION

Volume Press the ◄► buttons to adjust the audio Volume.

Bass Press the ◄► buttons to adjust the audio Bass.

Treble Press the ◄► buttons to adjust the audio Treble.

Mute Press the ◄► buttons to turn on or off the speaker.

AGC Press the ◄► buttons to turn on or off the AGC setting.

Reset Press the ENTER button to reset all settings to default values.

Lamp

Press the ENTER button to enter the Lamp sub menu.

InFocus SP8600 — Lamp diagram (page 33)
Fig. 46 · Lamp

I TEM D ESCRIPTION

Lamp Mode Press the ◄► buttons to adjust lamp brightness.

Press the ENTER button to reset the Lamp Hour after the lamp is replaced. Reset Lamp Timer

Lamp Hour Displays the number of hours the lamp has been in use.

Page 34 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 34 · click to enlarge
Page 34

HDMI

Press the ENTER button to enter the HDMI sub menu.

InFocus SP8600 — HDMI diagram (page 34)
Fig. 47

I TEM D ESCRIPTION

Press the ◄► buttons to select from three HDMI display formats: Auto/ PC signal/ Video signal. HDMI Format

HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain.

Closed Caption

Press the ENTER button to enter the Closed Caption sub menu.

InFocus SP8600 — Closed Caption diagram (page 34)
Fig. 48 · Closed Caption

I TEM D ESCRIPTION

Closed Caption Enable Press the ◄► buttons to turn on or off Closed Caption.

Caption Version Press the ◄► buttons to select the Caption Version.

Page 35 of the InFocus SP8600 user manual — I TEM D ESCRIPTION
Page 35 · click to enlarge
Page 35

STATUS Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu.

InFocus SP8600 — STATUS Menu diagram (page 35)
Fig. 49 · STATUS Menu

I TEM D ESCRIPTION

Source Displays the activated input source.

Resolution Displays the current resolution of input source.

Lamp Hour Displays the number of hours the lamp has been in use.

Firmware Version Displays the firmware version of the projector.

Page 36 of the InFocus SP8600 user manual — Replacing the Projection Lamp
Page 36 · click to enlarge
Page 36

M AINTENANCE AND S ECURITY

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

InFocus SP8600 — Replacing the Projection Lamp diagram (page 36)
Fig. 50 · Replacing the Projection Lamp

b. Do not dispose this product with general household waste.

c. Disposal of this product must be carried out in accordance with the regulations of your local authority.

2. Remove the single screw on the lamp compartment cover.
Page 37 of the InFocus SP8600 user manual — Maintenance and Security
Page 37 · click to enlarge
Page 37
3. Remove the lamp compartment cover.
InFocus SP8600 — Maintenance and Security diagram (page 37)
Fig. 51 · Maintenance and Security
4. Remove the three screws from the lamp module.
InFocus SP8600 — Maintenance and Security diagram (page 37)
Fig. 52 · Maintenance and Security
5. Lift the module handle up.
6. Pull firmly on the module handle to remove the lamp module.
InFocus SP8600 — Maintenance and Security diagram (page 37)
Fig. 53 · Maintenance and Security
Page 38 of the InFocus SP8600 user manual — Maintenance and Security
Page 38 · click to enlarge
Page 38
7. Reverse steps 1 to 6 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.
Page 39 of the InFocus SP8600 user manual — Cleaning the Case
Page 39 · click to enlarge
Page 39

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the pro- jector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Page 40 of the InFocus SP8600 user manual — Using the Kensington ® Lock
Page 40 · click to enlarge
Page 40

Using the Kensington ® Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

The security lock corresponds to Kensington’s MicroSaver Security System. If you have any com- ment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, http://www.kensington.com.

Page 41 of the InFocus SP8600 user manual — Tips for Troubleshooting
Page 41 · click to enlarge
Page 41

T ROUBLESHOOTING

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose con- nection. Check the following before proceeding to the problem-specific solutions.

  • Use some other electrical device to confirm that the electrical outlet is working.
  • Ensure the projector is turned on.
  • Ensure all connections are securely attached.
  • Ensure the attached device is turned on.
  • Ensure a connected PC is not in suspended mode.
  • Ensure a connected notebook computer is configured for an external display. (This is usually done by pressing a Fn-key combination on the notebook).

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.

Keep a record of the steps you take when troubleshooting: The information may be useful when call- ing for technical support or for passing on to service personnel.

Page 42 of the InFocus SP8600 user manual — Problem: The image is streaked
Page 42 · click to enlarge
Page 42

LED Error Messages

InFocus SP8600 — LED Error Messages diagram (page 42)
Fig. 54 · LED Error Messages

E RROR C ODE M ESSAGES P OWER LED

Thermal Break Sensor error 4 blinks 4 blinks OFF

Lamp End of lamp life detected 5 blinks 3 blinks OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re- starting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact your service center.

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.

Problem: The image is wider at the top or bottom (trapezoid effect)

1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.

Problem: The image is reversed

Check the Projection setting on the Installation I menu of the OSD.

Problem: The image is streaked

1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another computer.
Page 43 of the InFocus SP8600 user manual — Problem: The projector does not respond to the remote control
Page 43 · click to enlarge
Page 43

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Image menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cord is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Lamp LED is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Page 44 of the InFocus SP8600 user manual — Need Assistance?
Page 44 · click to enlarge
Page 44

Audio Problems

Problem: There is no sound

1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.

Need Assistance?

If you need assistance, visit our website at www.infocus.com/service or call us. Check out our HOW TO section there for additional information on using this projector for home theater applications.

This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the projector in its original packing material, or having a professional packaging company pack the projector. Please insure your shipment for its full value.

Page 45 of the InFocus SP8600 user manual — Q. How do I run HDMI cables longer than 10 meters?
Page 45 · click to enlarge
Page 45

HDMI Q & A

Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable?

Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High- Speed cables.

․Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or

up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.

․High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of

340Mhz or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can successfully handle 1080p signals including those at increased color depths and/or increased refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).

Q. How do I run HDMI cables longer than 10 meters?

There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective distance from the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that include active cables (active electronics built into cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and fiber solutions.

Q. How can I tell if a cable is an HDMI certified cable?

All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test Specification. However, there may be instances where cables bearing the HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively investigates these instances to ensure that the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from a reputable source and a company that is trusted.

For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49

Page 46 of the InFocus SP8600 user manual — Specifications
Page 46 · click to enlarge
Page 46

S PECIFICATIONS

Specifications

InFocus SP8600 — Specifications diagram (page 46)
Fig. 55 · Specifications

SDTV/ EDTV/ HDTV 480i, 480p,576i, 576p, 720p, 1080i, 1080p

Safety certification FCC-B, UL, cUL, CB, CE, CCC, PCT, PSB, SAB, and C-tick

Dimensions (W x H x D) 326 mm x 104 mm x 254 mm ( 12.8" x 4.1" x 10")

AC Universal 100 ~ 240, Typical @ 110VAC (100~240)/ ± 10% AC Input

Audioψ 3.5 mm stereo mini jack x 1; RCA x 2 R/L
SCREEN TRIGGERDC Jack x 1 (DC12V 200mA output function)
Page 47 of the InFocus SP8600 user manual — Projection Distance and Size Table
Page 47 · click to enlarge
Page 47

Projection Distance vs. Projection Size

InFocus SP8600 — Projection Distance vs. Projection Size diagram (page 47)
Fig. 56 · Projection Distance vs. Projection Size

Projection Distance and Size Table

InFocus SP8600 — Projection Distance and Size Table diagram (page 47)
Fig. 57 · Projection Distance and Size Table
Page 48 of the InFocus SP8600 user manual — / S-V IDEO C OMPONENT RGB ( ANALOG )
Page 48 · click to enlarge
Page 48

Timing Mode Table

The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector.

InFocus SP8600 — Timing Mode Table diagram (page 48)
Fig. 58 · Timing Mode Table

/ S-V IDEO C OMPONENT RGB ( ANALOG )

720 x 400 37.9 85.0 — — O O

640 x 480 31.5 60.0 — — O O

640 x 480 37.9 72.8 — — O O

640 x 480 37.5 75.0 — — O O

640 x 480 43.3 85.0 — — O O

800 x 600 35.2 56.3 — — O O

800 x 600 37.9 60.3 — — O O

800 x 600 46.9 75.0 — — O O

800 x 600 48.1 72.2 — — O O

800 x 600 53.7 85.1 — — O O

1024 x 768 48.4 60.0 — — O O

1024 x 768 56.5 70.1 — — O O

1024 x 768 60.0 75.0 — — O O

1024 x 768 68.7 85.0 — — O O

1280 x 800 49.7 59.8 — — O O

1280 x 800 62.8 74.9 — — O O

1280 x 800 71.6 84.8 — — O O

1280 x 1024 64.0 60.0 — — O O

1280 x 1024 80.0 75.0 — — O O

1280 x 1024 91.1 85.0 — — O O

1400 x 1050 65.3 60.0 — — O O

1440 x 900 55.9 60.0 — — O O

640 x 480 35.0 66.7 — — O O

1024 x 768 60.2 74.9 — — O O Apple Macintosh

832 x 624 49.7 74.5 — — O O

1152 x 870 68.7 75.1 — — O O

Page 49 of the InFocus SP8600 user manual — HDTV
Page 49 · click to enlarge
Page 49

S IGNAL R ESOLUTION H-S YNC

V-S YNC

C OMPOSITE

/ S-V IDEO C OMPONENT RGB ( ANALOG )

HDMI ( DIGITAL )

(KH Z )

(H Z )

720p 37.5 50.0 — O — O

720p 45.0 60.0 — O — O

1080i 33.8 60.0 — O — O

HDTV

1080i 28.1 50.0 — O — O

1080p 67.5 60.0 — O — O

1080p 56.3 50.0 — O — O

O: Frequency supported

—: Frequency not supported

The native resolution of the panel is 1920 x 1080. Resolution other than native resolution may display with uneven size of text or lines.

Page 50 of the InFocus SP8600 user manual — Projector Dimensions
Page 50 · click to enlarge
Page 50

Projector Dimensions

254 mm 104 mm

326 mm · 98 mm

Page 51 of the InFocus SP8600 user manual — Safety Certifications
Page 51 · click to enlarge
Page 51

R EGULATORY C OMPLIANCE

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica- tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could void the user’s authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

FCC-B, UL, cUL, CB, CE, CCC, PCT, PSB, SAB, and C-tick

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the InFocus SP8600

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus SP8600

Be the first to ask — other owners or our team will answer.

Original document

InFocus SP8600 manual PDF

51 pages·5 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…