EN
InFocus logo
Official user manual

InFocus FDV 16VB

30 pages·297 KB·Impact Driver·PDF·ENJA
InFocus FDV 16VB
Table of Contents 10 sections FDV 16VB · FDV16VB · GENERAL SAFETY RULES · PRECAUTION · … ShowHide
Page 1 of the InFocus FDV 16VB user manual — Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo
Page 1 · click to enlarge
Page 1

Impact Drill Schlagbohrmaschine Perceuse à percussion Trapano battente Slagboormachine Taladro de impacto

  • FDV 16VB
  • FDV 16T
  • FDV 16
InFocus FDV 16VB — Impact Drill Schlagbohrmaschine Perceuse à percussion Trapano battente Slagboormachine Taladro de impacto diagram (page 1)
Fig. 1 · Impact Drill Schlagbohrmaschine Perceuse à percussio…

FDV 16VB

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste istruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso.

Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo

Page 2 of the InFocus FDV 16VB user manual — FDV16VB
Page 2 · click to enlarge
Page 2

33 Tapping Screw (W/Flange) D4 × 16

Parts are subject to possible modification

The drawing and the list are parts structural

For other models refer to the drawing and

drawing and parts list of model FDV16VB.

without notice due to improvements.

No. Part Name

35 Internal Wire (B)

36 Internal Wire (A)

the list.

Part NameFlat Hd. Screw (A) (Left Hand) M6 25 ×Chuck Wrench For 13VLB-D, 13VLR-DDrill Chuck 13VLRB-DDrill Chuck 13VLRC-N (W/O Chuck Wrench)SpindleSpringBall Bearing (6201VVCMPS2S)Retaining Ring For D12 ShaftGearSteel Ball D4.76Change KnobChange PlateSpring (A)HolderBall Bearing (608VVMC2EPS2L)ArmatureStatorBall Bearing (626VVMC2ERPS2S)Housing (A) • (B) SetNameplateTapping SCrew (W/Flange) D4 20 ×Carbon BrushBrush HolderChoke CoilInternal Wire (D)Switch (M)Internal Wire (C)Choke CoilHITACHI LabelLabel Item No.12334567891011121314151617181920212223242526272829

FDV16VB

The exploded assembly drawing should be used only for authorized service center.

InFocus FDV 16VB — FDV16VB diagram (page 2)
Fig. 2

FDV16VB

Show 10 more labels / short text on this page
37 Noise Suppressor · 38 Earth Terminal · 502 Depth Gauge · 31 Cord Armor · 501 Side Handle · 32 Cord Clip · 30 Tube (D) · 34A Cord · 503 Case · Item
Page 3 of the InFocus FDV 16VB user manual — FDV16VB
Page 3 · click to enlarge
Page 3
InFocus FDV 16VB — FDV16VB diagram (page 3)
Fig. 3
Page 4 of the InFocus FDV 16VB user manual — FDV16VB
Page 4 · click to enlarge
Page 4
EnglishDeutschFrançais 1RingRingAnneau 2SleeveManschetteManchon 3TightenAnziehenSerrer 4LoosenLösenDesserrer 5Side handleSeitengriffPoignée latérale 6Chuck wrenchBohrfutterschlüsselClef pour mendrin 7ClockwiseIm UhrzeigersinnSens horaire 8CounterclockwiseGegen den UhrzeigersinnSens antihoraire 9Rotation + ImpactSchlagbohrfunktionRotation + Percussion ;RotationReine BohrfunktionRotation AAdjust knobEinstellknopfBouton de réglage BHigh speedHohe GeschwindigkeitGrande vitesse CLow speedNiedrige GeschwindigkeitPetite vitesse DStopperStopperButée EShift knobUmschaltknopfSélecteur ItalianoNederlandsEspañol 1AnelloRingAnillo 2CollareKlembusManguito 3StringereAandraaienApretar 4AllentareLosdraaenAflojar 5Impugnatura lateralZijgreepMango lateral 6Chiave per mandrinoBoorhoudersleutelVolvedor de mandrill 7Senso orarioRechtsomA derecha 8Senso antiorarioLinksomA izquierda 9Rotazione e impattoSlagboorfunctieRotación ;RotazioneNormale boorfunctiePerilla de cambio AManopola di regolazioneStelknopPerilla de ajuste BAlta velocitàHoge snelheidAlta velocidad CBassa velocitàLage snelheidBaja velocidad DFermoStopperRetén EManopola d’inter cambioVersnellingsknopNo. de escobilla de carbón
Page 5 of the InFocus FDV 16VB user manual — PRECAUTION
Page 5 · click to enlarge
Page 5

GENERAL SAFETY RULES

A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust

SAVE THESE INSTRUCTIONS 1) Work area a) Keep work area clean and well lit.

extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards.

Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust of fumes. c) Keep children and bystanders away while operating

4. Power tool use and care a) Do not force the power tool. Use the correct

power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not

a power tool. Distractions can cause you to lose control.

2. Electrical safety a) Power tool plugs must match the outlet.

turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source before

Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions.

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or

Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for

binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc.,

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock

3. Personal safety a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection.

in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Avoid accidental starting. Ensure the switch is in

5. Service a) Have your power tool serviced by a qualified

repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before

PRECAUTION

Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons.

turning the power tool on.

Page 6 of the InFocus FDV 16VB user manual — PRIOR TO OPERATION
Page 6 · click to enlarge
Page 6

Additional rules for impact drills

- Wear ear protection

Exposure to noise can cause hearing loss. - Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

SPECIFICATIONS

ModelFDV16VBFDV16TFDV16 Voltage (by areas)*(110V, 115V, 120V, 127V, 220V, 230V, 240V) Power Input550W* No-Load Speed0 – 2900/minHighLow2900/min 2900/min2300/min Capacity: Steel Concrete Wood13mm 16mm 25mm Weight (w/o cord)1.6kg

* Be sure to check the nameplate on product as it is subject to change by areas.

4. Side handle attachment Attach the side handle to the mounting part. Rotate the side handle grip in a clockwise direction to secure it. Set the side handle to a position that is suited to the operation and then securely tighten the side handle grip. 5. Mounting and dismounting of the bit.

STANDARD ACCESSORIES

For entire area (1) Side handle 1 (2) Depth stopper 1

For partial areas (1) Chuck wrench 1

(For drill chuck with chuck wrench) (2) Plastic case 1 Standard accessories are subject to change without notice.

For keyless chuck (1) Mounting the bit

After inserting a driver bit, etc. into the keyless drill chuck, firmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig.1) If the sleeve becomes loose during operation, tighten

APPLICATION

By combined action of ROTATION and IMPACT:

Boring holes in concrete, marble, granite, tile, and similar materials. By ROTATION only:

it further. The tightening force becomes stronger when the sleeve is tightened. (2) Dismounting the bit

Boring holes in metals, wood and plastics. Tightening wood screws.

Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front). (See Fig.1) NOTE When the sleeve does not become loose any fur- ther, fix the side handle to the sleeve. Then, strike the grip of the side handle to the left in order to loosen the sleeve,while holding the ring by hand. (Fig.2) CAUTION Do not fix the side handle to the ring of the keyless chuck because of a risk that doing so may damage the ring.

PRIOR TO OPERATION

1. Power source Ensure that the power source to be utilized con- forms to the power requirements specified on the product nameplate. 2. Power switch Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident. 3. Extension cord When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

For Drill chuck with chuck wrench

Fit the drill bit into the chuck and use the chuck wrench to secure it, tightening the chuck by each of the three holes in turn. (Fig.3) 6. Selecting the appropriate drill bit When boring concrete or stone:

Use the drill bits for concrete. When boring metal or plastic:

Use an ordinary metalworking drill bit.

Page 7 of the InFocus FDV 16VB user manual — MAINTENANCE AND INSPECTION
Page 7 · click to enlarge
Page 7

When boring wood:

The drill speed can be adjusted from 0 through maximum speed by regulating the trigger squeez- ing force. The more the trigger is squeezed, the faster the drill rotates. When the trigger is squeezed fully, the speed becomes maximum speed. Turn the adjust- ing knob clockwise for higher speed and counter- clockwise for lower speed. (Rotate the adjusting knob approximately 2-2/3 turns.) (Fig.6) FDV16T

Use an ordinary woodworking drill bit. However, when drilling 6.5mm or smaller holes, use a metalworking drill bit. 7. Selecting the driver bit Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is employed to drive in the screws. 8. Confirm the direction of bit rotation (Fig.4) (FDV16VB) The bit rotates clockwise (viewed from the rear) by pushing the R-side of the reverse switch. The L-side of the switch is pushed to turn screws counterclockwise (i.e. to loosen them.) CAUTION Never change the direction of bit rotation during

To change speed, slide the shift knob in the appropriate direction, as indicated by the arrow in Fig.7. The mark “H” printed on the shift knob denotes High speed. The mark “L” denotes Low speed. When the shift knob is in High speed position, the rotation speed of the drill bit can be changed in two stages (High speed/Low speed) according to the method of pressing the switch trigger. FDV16

operation. Turn the power switch OFF before changing the direction of bit rotation; otherwise, the motor will burn. Always use with clockwise rotation, when using it

The maximum speed can be obtained by pulling the trigger switch. Pull the trigger switch and push the stopper, this

as an impact drill. 9. IMPACT to ROTATION changeover (Fig.5) The impact drill can be switched from IMPACT (impact plus rotation) to ROTATION (rotation only) by simply sliding the change lever. When boring concrete, stone, tile or similar board materials, slide the change lever right. The drill head impacts against the material while continuing to rotate. When boring metal, wood or plastic, slide the change lever fully to the left. The drill simply rotates as an ordinary electric drill. CAUTION Do not use the impact drill in the IMPACT mode if the material can be bored by rotation only. Such action will not only reduce drill efficiency, but may also damage the drill tip. When changing over, ensure the change lever is slid as far as it will go.

keeps the switched in the on position, which is convenient for continuous running. The stopper can be released by pulling the trigger again. CAUTION Drill at a maximum rotation speed when drilling wooden materials. 5. When driving wood screws (FDV16VB) (1) Selecting a suitable driver bit

Employ plus-head screws, if possible, since the driver bit easily slips off the heads of minus-head screws. (2) Driving in wood screws Prior to driving in wood screws, make holes suit-

able for them on the wooden board. Apply the bit to the screw head grooves and gently drive the screws into the holes. After rotating the screwdriver at low speed for a

while until a wood screw is partly driven into the wood, squeeze the trigger more strongly to obtain optimum driving force. CAUTION Exercise care in preparing a hole suitable for the

HOW TO USE

1. Pressure Drilling will NOT be accelerated by placing heavy pressure on the drill. Such action will only result in a damaged drill bit, decreased drilling efficiency and/or shortened service life of the drill. 2. Using a large diameter drill bit The larger the drill bit diameter, the larger the reactive force on your arm. Be careful not to lose control of the drill because of this reactive force. To maintain firm control, establish a good foothold, hold the drill tightly with both hands, and ensure that the drill is vertical to the material being drilled. 3. When drilling completely through the material When the drill bit bores completely through the material, careless handling often results in a bro- ken, drill bit or damage to the drill body itself due to the sudden movement of the drill. Always be alert and ready to release pushing force when drilling through the material. 4. Speed adjustment and switch operation FDV16VB

wood screws taking the hardness of the wood into consideration. Should the hole be excessively small or shallow, requiring much power to drive the screw into it, the thread of the wood screw may sometimes be damaged. Do not drive machine screws.

MAINTENANCE AND INSPECTION

1. Inspection the drill bit Continued use of a worn and/or damaged drill bit will result in reduced drilling efficiency and may seriously overload the drill motor. Inspect the drill bit often and replace it with a new bit as necessary. 2. Inspecting the mounting screws: Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.
Page 8 of the InFocus FDV 16VB user manual — HOW TO USE
Page 8 · click to enlarge
Page 8
3. Maintenance of the motor The motor unit winding is very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet oil or water. 4. Servicing Consult an authorized Service Center in the event of power tool failure.

Blue: –Neutral Brown: –Live As the colours of the wires in the main lead of this tool may not correspond with the coloured markings identi- fying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the termi- nal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE This requirement is provided according to BRITISH STAN- DARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markets except the United Kingdom.

Information concerning airborne noise and vibration The measured values were determined according to EN 60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level108 dB(A) Measured A-weighted sound pressure level: 97 dB(A) Uncertainty KpA: 3 dB(A)

Wear ear protection.

The typical weighted root mean square acceleration value: 17 m/s2.

Ask about the InFocus FDV 16VB

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the InFocus FDV 16VB

Be the first to ask — other owners or our team will answer.

Original document

InFocus FDV 16VB manual PDF

30 pages·297 KB·Impact Driver·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…