Instruction/ maintenance manual of the product IZGS 68 ICTX IDEAL INDUSTRIES
Go to page of 20
Gas Hob IZGS 68 I CTX EG.
2 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual car efully and keep it throughout the pr oduct life cycle as a refer ence document.
3 Important Safety Information ............................................................................. 4 Description of the appliance .............................................................................. 6 Operation ....................
4 Installation The work of installation must be carried out by competent and qualified installers according to the regulations in force. • Any modifications to the domestic electrical mains which may be necessary for the installation of the appliance should be carried out only by competent personnel.
5 appliance. A poor air supply could cause lack of oxygen. • Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. • This appliance is not connected to a combustion products evacuation device.
6 Description of the appliance 1 Auxiliary burner 2 Semi-rapid burner 3 Triple crown burner 4 Control knobs 3 2 1 2 4.
7 Operation Hob burner control knobs The symbols on the knobs mean: = no gas supply = maximum gas supply = minimum gas supply For easier lighting, proceed before putting a pan on the pan support . Lighting the burners To light a burner, turn the relevant knob anticlockwise to maximum position ( ) and push down the knob to ignite.
8 Using the hob corr ectly Practical hints The burners To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used.
9 Cleaning and Mainteinance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine.
10 The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers.
11 Cut out dimensions (see chapter “Building In”) W idth: 560 mm Depth: 480 mm Overall dimensions W idth: 594 mm Depth: 510 mm T echnical data Heat Input T riple Crown burner 4,0 kW Semi-rapid bur.
12 Installation The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in for ce.
13 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). Important When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation.
14 A. Injectors replacement • Ensur e that the gas taps are in the 'OFF' position • Isolate the hob from the electrical supply • Remove all pan supports, burner caps, rings, cr owns and control knobs.
15 The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
16 Remplacement of the voltage cable The connection of the voltage cable to the appliance's terminal block is of type "Y". This means that its replacement requires the specific equipment of a technician. In this case, only cable type H05V2V2-F T90 must be used.
17 Building In These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 4; the cut out dimensions are shown in Fig. 5. The edge of the cut out must have a minimum distance from the rear wall of 55 mm.
18 Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig.
19 Fig. 9 Fig. 10 Service and original spar e parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention.
3971350.01 05/09 R.A.
An important point after buying a device IDEAL INDUSTRIES IZGS 68 ICTX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought IDEAL INDUSTRIES IZGS 68 ICTX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data IDEAL INDUSTRIES IZGS 68 ICTX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, IDEAL INDUSTRIES IZGS 68 ICTX you will learn all the available features of the product, as well as information on its operation. The information that you get IDEAL INDUSTRIES IZGS 68 ICTX will certainly help you make a decision on the purchase.
If you already are a holder of IDEAL INDUSTRIES IZGS 68 ICTX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime IDEAL INDUSTRIES IZGS 68 ICTX.
However, one of the most important roles played by the user manual is to help in solving problems with IDEAL INDUSTRIES IZGS 68 ICTX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device IDEAL INDUSTRIES IZGS 68 ICTX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
