Instruction/ maintenance manual of the product DB-200H Hoshizaki
Go to page of 19
™ INSTRUCTION MANUAL ISSUED: JUNE 5, 2001 DB-200H ICE DISPENSING BIN R eliability is a beautiful thing TM REVISED: DEC. 10, 2003.
2 IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT Only qualified service technicians should attempt to install, service or maintain this ice dispenser. No installation, service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual.
3 • Please review this manual. It should be read carefully before the ice dispenser is installed and operated. Only qualified service technicians should install, service and maintain the ice dispenser. This manual should be made available to the technician prior to installation, maintenance or service.
4 We reserve the right to make changes in specifications and design without prior notice. See NAMEPLATE for electrical specifications. The nameplate is located on the upper part of the Right Side Panel. I. SPECIFICATIONS I. SPECIFICATIONS I. SPECIFICATIONS I.
5 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS 2. DIMENSIONS/CONNECTIONS [a] with KM-280M_ or KM-500M_ [a] with KM-280M_ or KM-500M_ [a] with.
6 [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M [b] with KM-630M.
7 [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_, KML-450M_, or KML-600M_H [c] with KML-250M_, KML-350M_,.
8 II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS II. INSTALLATION AND OPERATING INSTRUCTIONS 1. CHECKS BEFORE INSTALLATION 1.
9 WARNING WARNING WARNING WARNING WARNING This ice dispensing bin is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F. To the icemaker, water temperature should be within +45°F to +90°F. Extended periods of operation at temperatures outside of these limitations may cause unsatisfactory results.
10 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. 3. SET UP - See Fig. 1. CAUTION CAUTION CAUTION CAUTION CAUTION It is especially important that the icemaker/ice dispensing bin is leveled in both left-to-right and front-to-rear directions.
11 Fig. 1 Fig. 1 Fig. 1 Fig. 1 Fig. 1 *Note: With KML models, Top Panels are not necessary..
12 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION 4. ELECTRICAL CONNECTION WARNING WARNING WARNING WARNING WARNING 1. Electrical connection must be made in accordance with the instructions on a “WARNING” tag, provided with the pig tail leads in the Junction Box.
13 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 5. DRAIN CONNECTIONS - See Fig. 4 1. A drain outlet, 3/4" FPT, is located at the rear of the ice dispensing bin.
14 Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection Fig. 4 Drain Connection.
15 7. START UP 7. START UP 7. START UP 7. START UP 7. START UP 1) Start up the icemaker. See the “START UP” instructions on the icemaker. 2) Allow at least three (3) cycles of ice production, and then place a proper container in the ice station. 3) Push the ice dispensing switch to dispense ice cubes.
16 III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III. CLEANING AND MAINTENANCE INSTRUCTIONS III.
17 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Fig. 5 Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Inside of the Bin Agitator Agitator Agitator Agitator Agitator Spout of the Spout of the S.
18 7) Scrub the Shutter Assembly and Spout—after removing them—using the cleaning solution of item 6. See Fig. 5. a) Remove the Snap Pin fitted to the Shutter Shaft and shift the Shaft to the left. Then the Shutter Assembly can be removed from the bin.
19 91A4JB10C HOSHIZAKI HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. HOSHIZAKI AMERICA, INC. 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 SOUTH 618 HIGHWAY 74 .
An important point after buying a device Hoshizaki DB-200H (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoshizaki DB-200H yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoshizaki DB-200H - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoshizaki DB-200H you will learn all the available features of the product, as well as information on its operation. The information that you get Hoshizaki DB-200H will certainly help you make a decision on the purchase.
If you already are a holder of Hoshizaki DB-200H, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoshizaki DB-200H.
However, one of the most important roles played by the user manual is to help in solving problems with Hoshizaki DB-200H. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoshizaki DB-200H along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
