Instruction/ maintenance manual of the product PRO-2200 Honeywell
Go to page of 16
P P P P R R R R O O O O - - - - 2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0 E E E E t t t t h h h h e e e e r r r r n n n n e e e e t t t t B B B B o o o o a a a a r r r r d d d d I I I I n n n n s s s s t t t t .
.
Contents W ar nings and Cautions .............................. 5 Disclaimer ........................................ 7 Unpacking Procedure ............................... 7 Shipping Instructions ................................ 8 Limited W arranty ..
W ARNINGS AND C A UTIONS WARNING Bef ore installation, tur n off the e xter nal circuit break er which supplies power to the system. Bef ore connecting the device to the po wer supply , verify that the output voltage is within specifications of the po wer supply .
WARNING Use suppressors on all door strikes. Use S-4 suppressors for installation. Engineering Systems recommends only DC str ikes . CAUTION IF ANY D AMA GE T O THE SHIPMENT IS NOTICED , A CLAIM MUST BE FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE. CAUTION Electro-static discharge can damage CMOS integrated circuits and modules.
NOTICE Any use of this product is subject to the terms and acceptance of the Engineering Systems Software Agreement. Please request a cop y from Engineering Systems, and revie w the agreement carefully .
If shipping caused damage to the unit, a claim must be filed with the commercial carrier . If any other def ect is apparent, call 800-323-4576 f or a return authorization. Shipping Instructions T o ship equipment bac k to Engineering Systems: 1. Contact the customer ser vice depar tment at 800-323-4576 bef ore retur ning equipment.
THERE ARE NO W ARRANTIES WHICH EXTEND BEY OND THIS PRO VISION. THIS W ARRANTY IS IN LIEU OF ALL O THER W ARRANTIES WHETHER EXPRESS , IMPLIED OR ST A TUT OR Y , INCLUDING IMPLIED W ARRANTIES OF MERCHANT ABILITY OR FITNESS FOR ANY P ARTICULAR PURPOSE.
P ROGRAMMING E THERNET D EVICES This cov ers all of the steps needed to get the PRO22EN Ethernet Daughter board on-line and working. Programming of these units will be outlined within this Installation Guide. PRO22EN Programming The PRO22EN will be prog rammed from a Command Prompt using the ARP command.
2. Set the dips witches on the PRO22IC (S1) to: Baud Rate is 38, 400 bps Flow Control is ON P anel Address is 1 S1 8 OFF (P ASSWORD OFF) 7 ON (BA UD RA TE) 6 ON (BA UD RA TE) 5 ON (FLO W CONTROL) 4 OFF (P ANEL ADDRESS) 3 OFF (P ANEL ADDRESS) 2 OFF (P ANEL ADDRESS) 1 ON (P ANEL ADDRESS) 3.
PROGRAMMING THE ETHERNET CARD 1. Go to a MS-DOS prompt. 2. T ype ar p -s XXX.XXX.XXX.XXX ??.??.??.??.?? <Enter> XXX.XXX.XXX.XXX = TCPIP Address for the Ethernet Card ??-??-??-??-??-?? = MA C Address of the Ether net Card. After pressing Enter the result will show nothing.
4. T ype T elnet XXX.XXX.XXX.XXX 1 <Enter> (IP Address and the number 1) Note: The 1 is por t "1". 5. The T elnet window ma y or ma y not connect to Host Name: XXX.XXX.XXX.XXX. Click OK 6. Select Connect and Remote System 7. V erify the Host Name is the correct IP Address and type: 9999 in P or t.
8. Press <Enter> f or Setup Mode 9. The f ollowing screen should appear . 10. Y our Choice? Enter 0 f or ser ver configur ation. 11. IP Address: (000) XXX.XXX.XXX.XXX <Enter> 12. Set Gate wa y IP Address T ype Y , if a gatewa y is needed. XXX.
19. P or t Number=3001 <Enter> (Winpak Pro uses por t 3001) 20. Select Enter through the rest of the men us 21. When the Main Men u Appears V erify that Channel 1 is Baudrate =38400, I/F Mode 4C , Flow 02 P or t 03001 Remote IP Adr : --- none ---, P or t 00000 Connect Mode: C0 Disconn Mode: 00 Flush Mode: 00 22.
CONTROLLER BOARD P o w e r RS-485 T ermination A B C 1 2 3 1 2 3 1 2 3 1 2 3 4 5 1 2 S1 Configuration Dip Switc hes J3 J2 J9 J12 J13 LAN Card Connector M e m o r y E x p a n s i o n C o n n e c t o r .
Honeywell Security & Data Collection 2700 Blankenbak er Pkwy , Suite 150 Louisville, KY 40299 (800) 675-3364 www.honeywellaccess.com.
An important point after buying a device Honeywell PRO-2200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honeywell PRO-2200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honeywell PRO-2200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honeywell PRO-2200 you will learn all the available features of the product, as well as information on its operation. The information that you get Honeywell PRO-2200 will certainly help you make a decision on the purchase.
If you already are a holder of Honeywell PRO-2200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honeywell PRO-2200.
However, one of the most important roles played by the user manual is to help in solving problems with Honeywell PRO-2200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honeywell PRO-2200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
