Instruction/ maintenance manual of the product SLA-2 ML-44180 Hobart
Go to page of 12
© HOBART 2006 F33995 (Rev. A, 6/06) Security Label Applier Operator Manual Model SLA-1, SLA-2 ML-44180 SLA-2A ML-44197 SLA-3 ML-44192 701 S. RIDGE AVENUE TROY, OHIO 45374 937 332-3000 www.
F33995 (Rev. A, 6/06) Page 2 of 12 © HOBART 2006 Security Label Applier (SLA) SAVE THESE INSTRUCTIONS Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
© HOBART 2006 Page 3 of 12 F33995 (Rev. A, 6/06) Security Label Applier The Security Label Applier (SLA) is designed to apply an Electronic Article Surveillance (EAS) label to a standard Ultima scale label.
F33995 (Rev. A, 6/06) Page 4 of 12 © HOBART 2006 Note If used with an HWS or NSW Semi Automatic System, the security label is automatically placed on the Ultima scale label. The Operator then hand applies the labels to the package. There are two types of security labels available.
© HOBART 2006 Page 5 of 12 F33995 (Rev. A, 6/06) 1. At the Ultima Keypad, PRESS [SUPER MENU ON/OFF]. If applicable, enter your Secret ID. The Supervisor Menu displays. 2. PRESS [F5] to select Scale Setup Menu. 3. PRESS [F3] to select Labels Menu. 4. PRESS [F6] to select Security Labels.
F33995 (Rev. A, 6/06) Page 6 of 12 © HOBART 2006 5. From the Security Labels screen, enter the minimum Unit Price and/or the minimum Total Price. A security label will be applied to any package with a Unit Price and/or Total Price that is the same as or higher than the amounts entered.
© HOBART 2006 Page 7 of 12 F33995 (Rev. A, 6/06) 3. Use the numeric keypad to enter PLU number in the Product number and PRESS [ENTER]. 4. PRESS [F2] to select Apply Security Label. 5. PRESS [ESC] to return to the Start a Run screen. Operating the SLA Once set up, the SLA runs with minimal operator intervention.
F33995 (Rev. A, 6/06) Page 8 of 12 © HOBART 2006 Loading Labels The SLA contains a label sensor to alert the operator when out of labels or when labels are not advancing. When applicable, the message Out of Security Labels displays on the Ultima console and a beep sounds to alert the operator.
© HOBART 2006 Page 9 of 12 F33995 (Rev. A, 6/06) Fig 1 Fig 2 Fig 3 Fig 4.
F33995 (Rev. A, 6/06) Page 10 of 12 © HOBART 2006 Cleaning and Maintaining Maintain the SLA by regularly cleaning the paper dust from inside the unit. Clean the SLA exterior surfaces with a cloth and warm water/detergent solution. When cleaning, be sure to protect the unit from direct water entry.
© HOBART 2006 Page 11 of 12 F33995 (Rev. A, 6/06) SYMPTOMS POSSIBLE CAUSES/REMIDIES Multiple labels are issued followed by an audible beeping sound. 1. Verify labels threaded correctly. 2. Call local Hobart office. No label is issued followed by an audible beeping sound .
© HOBART 2006 F33995 (Rev. A, 6/06).
An important point after buying a device Hobart SLA-2 ML-44180 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart SLA-2 ML-44180 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart SLA-2 ML-44180 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart SLA-2 ML-44180 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart SLA-2 ML-44180 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart SLA-2 ML-44180, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart SLA-2 ML-44180.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart SLA-2 ML-44180. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart SLA-2 ML-44180 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
