Instruction/ maintenance manual of the product R6 Harman Stove Company
Go to page of 13
1 R6 INVINCIBLE "RS" OWNERS MANUAL.
2 Contents Manufactur ed by Harman Stove Company 352 Mountain House Road Halifax Pa. 17032 (717) 362-9080 Packing List 3 Installation & Assembly 3 V enting 5 Operation 9 ESP Control 1 2 Maintenanc.
3 Packing List Assembly and Installation Final Assembly Remove parts from ash pan. Install W ooden Door Handle with 1/4 x 20 x 2 1/2 bolt. Install Brass Hopper Knob with 10-32 x 1/2 bolt. Install the two Firebricks on the angle iron behind the burn pot as shown in fig.
4 Installing Place the stove on a noncombustible floor pro- tector and away from combustible walls at least as far as shown in figure 2 and 3. Note that the clear- ances shown are minimum for safety but do not leave much room for access when cleaning or servicing.
5 V enting A combustion blower is used to extract the com- bustion gases from the firebox. This causes a nega- tive pressure in the firebox and a positive pressure in the venting system as shown in fig. 4. The longer the vent pipe and more elbows used in the system, the greater the flow resistance.
6 #2 Preferr ed method This method also provides excellent venting for normal operation but requires the stove to be installed farther from the wall. The vertical portion of the vent should be three to five feet high and at least three inches from a combustible wall.
7 #4 Installing into an existing chimney ( US only ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable you may want to install a liner as in method #7.
8 #6 Installing into an existing fireplace chimney ( US and Canada ) This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. In Canada and some places in the US it is re- quired that the vent pipe extend all the way to the top of the chimney .
9 DO NOT INST ALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT . DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SER VING ANOTHER APPLIANCE. INST ALL VENT A T CLEARANCES SPECIFIED BY THE MANUF ACTURER Mobile home installation should be done in accordance with the Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.
10 Operation Starting First Fir e Be sure the power cord is plugged into a 120 volt receptacle. This can be verified by the red power light on the control panel. Fill the hopper with pellets, fig. 12. Fill the burn pot with pellets to a level just short of overflowing, fig.
11 Starting a fir e after pr oper Feed Rate is known. Clean burn pot with scraper (supplied). Fill the hopper with pellets. Fill the burn pot with pellets to a level just short of overflowing. Adjust feed rate to proper setting. After you know what feed rate works well, then use that setting.
12 When to use "Stove T emp Mode" In "Stove T emp Mode" the Stove T emp Dial determines the temperature of the stove. Heat output and fuel consumption will remain con- stant. This makes it possible to tell how long a hopper full of pellets will last.
13 ESP CONTROL Feed adjuster Sets the maximum feed rate T est Runs all motors at full speed for two minutes to check operation. After two minutes the stove will go to minimum burn and the blowers will alternate fr om high to low every two minutes to remind you that you are still in "T est Mode".
An important point after buying a device Harman Stove Company R6 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Harman Stove Company R6 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Harman Stove Company R6 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Harman Stove Company R6 you will learn all the available features of the product, as well as information on its operation. The information that you get Harman Stove Company R6 will certainly help you make a decision on the purchase.
If you already are a holder of Harman Stove Company R6, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Harman Stove Company R6.
However, one of the most important roles played by the user manual is to help in solving problems with Harman Stove Company R6. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Harman Stove Company R6 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
