Instruction/ maintenance manual of the product SpeedDome Ultra VI American Dynamics
Go to page of 34
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 1 of 34 S peedDome ® Ultra VI Camera Domes Installation and Service Guide RAS816LS and RAS816WLS Series Figure 1. SpeedDome Ultra camera dome © 2005 Sensormatic Elect ronics Corp.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 2 of 34 About the Camera Dome The SpeedDome Ultra VI camera dome (Figure 1) comes in black or white finish (to ble nd into surrounding areas), mou nts indoors or outdoors, and can communicate with the video controller over a SensorNet 485, RS-422, or Manchester network.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 3 of 34 Figure 2. Mounting base and housing and eyeball assembly Standard Base Base with I/O Board Indoor Ceiling Mounting Using .
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 4 of 34 Indoor Ceiling/Wall Mounting (Optional) The camera dome attaches to one of the following optional indoor mounting structures (Figure 5 ).
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 5 of 34 Figure 5. Indoor mounting structures (option al) RHIUFB RHIUA B RHIUHC RHIU 2X2 RHIUTH RHIUTR RUCLR RUSLV RUSMK RUGLD RHI.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 6 of 34 Outdoor Mounting (Optional) Note: This document doe s not include outdoor installation and service instructions. Fo r these instructions, see Insta lling the RHODUL Outdoor Housing, 8000-2573 -04.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 7 of 34 Figure 8. Outdoor mounting structures (optional) RHOTR over roof mount (shown with RHOTRF bracket) PHOPN pendant mount RH.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 8 of 34 Dat a Cable Requirements Table 2 shows the data cable requirements for SensorNet, RS-422, and Manchester net works. For more information about communi cation protocols and cable networks, see Communication Protocols and Cable Networks, 8000-2573 -19.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 9 of 34 Power-Up Routine After power is connected to the dome, the dome performs the following hom ing routine. 1. After a few seconds, the camera lens tilts up into the housing and eyeball assembly.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 10 of 34 W arnings and Cautions Please review the following warning s and cautions before you begin installation or service. WARNINGS ! WARNING! ALWAYS USE: • Proper safety equipment for the location and type of installation.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 11 of 34 When using the standard b ase and wiring cables directly to the dome, ALWAYS connect the video cable to the dome before you conne ct the 9-pin cable (which contains power).
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 12 of 34 Connecting to the Standard Mounting Base This procedure explains how to conne ct the housing and eyeball assembly to a standard ba se.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 13 of 34 4. Set termination jumper JW1 (Figure 12). Depending upon the dom e’s location in the communications lin e, set jumper.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 14 of 34 6. Conne ct 4-pin plug (alarm input/output) t o 4-pin receptacle (Figure 13). a. Feed cable through access hole in base. b. Connect alarm wires to 4-pin plug (refer to chart be low).
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 15 of 34 8. Connect the housing and eyeball assembly to the base (Figure 14) by aligning the Cap and Base tabs and then turning clockwise until you hear a click. Figure 14. Connecting housing and eyeball assembly to base (cables and lanyard not sho w n) 9.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 16 of 34 Figure 15. Electrical connections 1 P1 P4 P3 P8 P7 JW1 I/O BOARD JW1 Terminations FUNCTION Termi nated Unterminated PINS 1- 2 2- 3 Pin 1 Pin 1 Pin 1 Pin 1 4. Conne ct alarm output cable, if used, to P3 connector.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 17 of 34 Figure 16. Test switch/LEDs on I/O board Comm. LED Pow er LED RS422 Te st Pushbu tton 10. Set dome address (Figu re 17). Recessed at top of housing and eyeball assembly are three rotary address switches.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 18 of 34 Using the Inst all/Removal T ool CAUTION: Do not use this tool to conne ct the dome to the standard base. Used only when the dome is connected t o a base having an I/O board, the RHIRT install/removal tool eliminates the need for a ladder during routine service.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 19 of 34 Figure 19. How to use the install/removal tool Skirt or Bubble Attachment/Detachment Dome Connection (reverse steps to disconnect) Do not use this tool to connect the standard base! Attachment Detach ment A B C Line up Line up B C D E Turn until you feel a click.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 20 of 34 T roubleshooting Indoor Domes CAUTION: This troublesh ooting section is for indoor camera domes only! To trouble shoot outdoor domes, see install ation and service manual shipped with the outdoor h ousing.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 21 of 34 Procedure Follow steps until the problem is correct ed. 1. Check video on monitor (a, b, or c). a. No video? Go to step 2. b. Contrast or color off? YES Ship entire dome (base inc luded, if it contains an I/O board) back to the GSC.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 22 of 34 6. Observe green power LED on I/O board (Figure 21). Is green LED off or not on steady? YES Verify 24Vac cable is properly attached. If OK, replace I/O board or ship entire dom e to the GSC.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 23 of 34 9. Check spring finger connector on I/O board by connecting housing an d eyeball assembly to original base to verify contact between spri ng fingers and CPU board (under cap ).
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 24 of 34 Disassembling the Dome CAUTION: Once disa ssembled, parts of dome housing and eyeball assembly are "extremely fragile" and may break. Proceed usi ng extreme care! This section explains how to remove the following parts from the camera dome.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 25 of 34 Removing the P/S Board CAUTION: Electrostatic-se nsitive device. Use a ground strap whe n handling power supply board. Referring to Figure 23. 1. Perform procedure "Removing the CPU Board" (page 27).
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 26 of 34 Removing the Slot Covers 1. Gently swivel eyeball to totally expose one of two slot covers (Figure 25). CAUTION: Swiveling fast can damag e gears. 2. Insert small, thin-bladed screwdriver into space between cover and eyeball.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 27 of 34 Detaching the Eyeball 1. Perform pro cedure "Removing the Slot Covers" (page 29). 2. Perform pro cedure "Removing the Camera" (this page). 3. Detach eyeball from housing (Figure 28 ).
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 28 of 34 The following steps refer to Figure 32. 6. Access camera/lens board. To do this, loosen captive retaining screw holding bearing assembly in place and remove this assembly.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 29 of 34 6. Access tilt motor. To do this, loosen captive retaining screw holding tilt cable assembly in place and gently remove this assembly. 7. Remove tilt motor (Figure 35). Lift motor housing up as shown (1) to di sengage motor from tilt gear.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 30 of 34 Illustrated Part s List This section helps you to identify parts that make up the base and housing and eyeball a ssembly. Parts in Table 3 are shown in Figure 37 . Note: Not all of the parts, which are shown for clarity, are orderable.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 31 of 34 Figure 37. Base, housing, and eyeball assembly 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 21 22 23 24 25 26 33 27 2.
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 32 of 34 Specifications-Indoor Dome Operational Pan/Tilt: Manual Pan S peed ............ 0.2°-100 ° per second (scaled to zoom position) Manual Tilt Speed ............. 0.25°-100° per second (scaled to zoom position) Preset Pan/Tilt Speed .
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 33 of 34 Lens and Bubble Densities Eyeball Lens ......................... f0 Bubbles: RUCLR (Clear ) .................. f0 RUSLV (Silver).................. f1.5 to f2 RUSMK (Smoke) .
SPEEDDOME ULTRA VI 8000-2830-03, REV. C INSTALLATION AND SERVICE GUIDE 34 of 34 Field-of-View Formulas: 3.2mm* x distance from camera (m) Focal length (mm) = Horizontal view (m) 2.4mm* x distance from camera (m) Focal length (mm) = Vertical view (m) * Horizontal scanning area of pi ckup device (mm) in camera.
An important point after buying a device American Dynamics SpeedDome Ultra VI (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Dynamics SpeedDome Ultra VI yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Dynamics SpeedDome Ultra VI - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Dynamics SpeedDome Ultra VI you will learn all the available features of the product, as well as information on its operation. The information that you get American Dynamics SpeedDome Ultra VI will certainly help you make a decision on the purchase.
If you already are a holder of American Dynamics SpeedDome Ultra VI, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Dynamics SpeedDome Ultra VI.
However, one of the most important roles played by the user manual is to help in solving problems with American Dynamics SpeedDome Ultra VI. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Dynamics SpeedDome Ultra VI along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
