Instruction/ maintenance manual of the product Milnor Phase 7.2.2 American Dryer Corp.
Go to page of 92
PHASE 7.2.2 NON-COIN USER’S MANUAL (F.S.S.) ADC Part No. 113193 - 4 American Dryer Corporation 88 Currant Road Fall River , MA 02720-4781 T elephone: (508) 678-9000 / Fax: (508) 678-9447 E-mail: techsupport@amdry .
Retain This Manual In A Safe Place For Futur e Refer ence Please read this manual carefully to thoroughly familiarize yourself with the Phase 7 non-coin microprocessor controller (computer) system features, operational instructions, and programming characteristics.
SECTION I INTRODUCTION ....................................................................................................... 3 SECTION II FEA TURES .....................................................................................................
SECTION IV OPERA TING INSTRUCTIONS ............................................................................... 14 A . Operating Sequence ........................................................................................................... ..
3 SECTION I INTRODUCTION Phase 7 Non-Coin Microprocessor Controller (Computer) Drying System The Phase 7 Non-Coin Microprocessor Controller (Computer) Drying System has been designed with super performance in mind to provide for better temperature regulation, efficiency , performance, consistency , and faster drying times.
4 SECTION II FEA TURES A. Dependable Phase 7 Non-Coin Micr opr ocessor Contr oller (Computer) Solid S tate Integrated Circuitry – Eliminates as many moving parts as possible. B. Fir e Suppr ession System (F .S.S.) – A standard feature, which continually monitors the basket (tumbler) for fires.
5 N. T emperatur e Conversion S tatus – T emperature-related programs can be set in either Fahrenheit (°F) or Celsius (°C). ALL temperatures will automatically convert to the corresponding values (+/- 1°) when changes are made.
6 SECTION III PROGRAM SELECTIONS A. PREPROGRAMMED CYCLES “A-F” CYCLES The Phase 7 non-coin microprocessor controller (computer) can store in its memory six (6) preprogrammed cycles (keys “A-F” on the keyboard [touch pad]).
7 PREPROGRAMMED CYCLE MENU SELECTIONS (CYCLES “A-F” or “0-40”): 1. Automatic Drying Cycle (Patent No. 4,827,627) a . The Phase 7 non-coin microprocessor controller (computer) can be programmed to reverse or not reverse. This is done in the “DR YER SETUP” parameter .
8 B. MANUALL Y LOADED CYCLES For occasional or onetime special loads, the operator must enter the specific program features needed. This cycle is not stored within the Phase 7 non-coin microprocessor controller (computer) and must be entered each time.
9 E. LIGHT EMITTING DIODE (L.E.D.) DOT MA TRIX DISPLA Y The L.E.D. display informs the user of cycle status, program verification, and displays important diagnostic and fault information. A complete listing of the various display messages and their meanings is shown in Section V of this manual.
10 H. WRINKLE GUARD PROGRAM This program keeps items wrinkle-free when they are not removed from the dryer promptly at the end of the drying and/or cooling cycles. When the drying and cooling cycles are completed, the dryer will shut off, the tone will sound, and the light emitting diode (L.
11 K. REVERSING OPTION This feature helps reduce balling-up or tangling of large items. REVERSING OPTION SELECTIONS: 1. Reverse On or Reverse Off 2. This option can be set to “ON” or “OFF” for each cycle individually . 3. Basket (Tumbler) Spin T ime and Dwell (Stop) T ime a .
12 0. DR YER SETUP – ALL parameters that pertain to drying are in this menu level. 0. SELECT MODEL – This allows the selection of the heat source applied to the dryer , and whether the dryer is reversing or non-reversing. GAS REVERSING GAS NON-REVERSING STEAM REVERSING STEAM NON-REVERSING ELECTRIC REVERSING ELECTRIC NON-REVERSING 1.
13 1. REVERSING SETUP – The parameters that pertain to the Reversing Mode are in this menu level. 0. ENTER SPIN TIME 30 TO 120 SECONDS – This parameter (program) is fixed at 2 minutes in the forward direction and 2 minutes in the reverse direction for the Automatic Mode.
14 SECTION IV OPERA TING INSTRUCTIONS The Phase 7 non-coin microprocessor controller (computer) allows the operator to choose from six (6) preprogrammed cycles (keys “A-F”). These have been preprogrammed by the factory with the parameters (programs) shown in Section VII .
15 6) Once the Cool Down Cycle begins at the end of the heat cycle, the light emitting diode (L.E.D.) display will read COOL DOWN TEMP ___/___ MINUTES REMAINING. At the end of the heat cycle, the dryer will shut off the heat and continue the fan and basket (tumbler) until the Cool Down T ime or temperature is reached.
16 7) Once the Cool Down Cycle is completed, the Phase 7 non-coin microprocessor controller (computer) will proceed into the W rinkle Guard Cycle. The Audio Alert tone will sound (for the amount set in Audio Alert On Time). The light emitting diode (L.
17 NOTE: Press and hold the “DOWN ARROW” to view the basket (tumbler) RPM. 7) Once the preprogrammed percentage of extraction (dryness level) is reached, the drying cycle will end and the Cool Down Cycle will begin. 8) Once the Cool Down Cycle begins at the end of the heat cycle, the light emitting diode (L.
18 7) The dryer will now display “PRESS ST AR T”. Press the “ST AR T/ENTER” key to start the dryer . The light emitting diode (L.E.D.) display will read MANUAL DR YING CYCLE, __MINUTES REMAIN. NOTE: The dryer can be stopped at any time by pressing the “STOP/CLEAR” key; at this time the dryer will go into a cycle pause.
19 6. In the Programming Mode, the number keys can be used to jump to menu levels without scrolling through them ALL . I.E., from 0 select Model in “DR YER SETUP”; you can jump to menu level five (5). Enter Lint Cleaning Frequency under “DR YER SETUP” by pressing the five (5) key followed by the “ST AR T/ENTER” key to accept value.
20 FIRE SUPPRESSION SYSTEM (F .S.S.) V AL VE CHECK The operation of the water solenoid valve can be tested to insure that the water supply system and valve are functional.
21 SHOR TED W A TER V AL VE – This indicates the water valve is shorted or the wiring to the valve is shorted. If this condition is detected, the Phase 7 non-coin microprocessor controller (computer) will continue to monitor the condition for a period of 5 minutes before entering F .
22 SECTION V L.E.D. DISPLA Y MESSAGES The light emitting diode (L.E.D.) display informs the operator of cycle status and program verification, and also displays important diagnostic messages and fault information. A. L.E.D. DISPLA Y OPERA TING ST A TUS 1.
23 SECTION VI PROGRAMMING INSTRUCTIONS A. INTRODUCTION TO PROGRAMMING The various program selections are stored in the Phase 7 non-coin microprocessor controller (computer) and are broken down into five (5) categories: 0. Language (ENGLISH, FRANCAIS, ESP ANOL, IT ALIANO, and DEUTSCH).
24 T o alter the programming parameters, the operator will locate the parameter (program) that is to be changed. If the change is numerical (i.e., time and/or temperature), the operator will simply enter the numerical value desired. If an error is made, press the “STOP/CLEAR” key ONCE and the incorrect entry that was made will be cancelled.
25 Ready B. PROGRAMMING FLOWCHAR TS The following section of this manual explains the programming of the preprogrammed cycles and Program Locations (system parameters) through the use of flowcharts. A flowchart is a diagram of the programming process.
26 PHASE 7 MENU PROGRAMMING PROCEDURE EVER Y INDENTED STEP REPRESENTS THE “ST AR T/ENTER” KEY BEING PRESSED T O SELECT A MENU ITEM. EVER Y MESSAGE WITH A NUMBER BEFORE IT INDICA TES THA T IT IS A MENU SELECTION CHOICE. EVER Y MESSAGE WITHOUT A NUMBER BEFORE IT INDICA TES THA T IT IS THE LAST MENU LEVEL.
27 0 : SELECT LANGUAGE ENGLISH FRANCAIS ESP ANOL IT ALIANO DEUTSCH 1 : SELECT SYSTEM P ARAMETERS 0 : DR YER SETUP 0 : SELECT MODEL GAS REVERSING ELECTRIC REVERSING STEAM REVERSING GAS NON-REVERSING EL.
28 2 : PROGRAM “A-F” CYCLE SELECT “A-F” KEY * (“*” DISPLA Y THE LETTER CHOSEN. DEF AUL TS T O “A”) SELECT CYCLE TYPE * (“*” DISPLA Y THE CYCLE TYPE “AUTO” or “MANUAL”) AUTO.
29 Selecting La nguages Ready 0:SELECT LANGUAGE Press and h old the stop /cle ar k ey While holding the stop/ clear ke y, pre ss th e up arrow ke y. ENGLISH Pres s the up or down ar row key to select a di ffere nt lang uag e. ENGLISH, FRANCAIS, ESPANOL, ITALIANO, and DEUTSCH are the se l ection s.
30 Selecting a Dryer Mo del Ready 0:S ELEC T LANGUAGE The comp uter mu st b e dis play ing REA DY to enter program mode Press and ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess the up arrow key.
31 From Previous GAS REVERSING Press th e up or d own arro w key to s elect a di ffer ent m odel . GAS REVERSI NG, ELECTRIC REVERSING, STEAM REVERSING, GAS NON- REVERSING, ELECTRIC NON-REVERSING and STEAM NON-REVERSING are the sel e ct i on s.
32 Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess the up arrow key. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP 0: SEL E CT MODEL Next pag.
33 From Previo us 1: SYSTEM TEMP Press the up or do wn arrow key t o selec t DEG F o r DEG C DEG C 1 DEG F Use ar row key Or number Press ENTER to jum p direc tly to the lo cat ion Press EN T E R to a.
34 Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess the up arrow k ey. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP 0: SEL E CT MODEL Next pa.
35 From Previous 2: ENTER LINT CLEANING FREQUENCY 1 T O 10 HOURS 3 3: ENTER AUDIO ALERT ON TIMES 0 TO 10 5 2 Press t he up ar row key to incremen t the numb er , do wn ar ro w key t o decremen t the numb er or e nt er the numbe r di r ect ly .
36 Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess t h e up arrow k ey. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP 0: SEL E CT MODEL Next .
37 From Previous 3: ENTER AUDIO ALERT ON TIME S 0 TO 10 5 1: SYSTEM TEMP 2: ENTER LINT CLEANING FREQUENCY 1 TO 10 HOURS 3 Next page Press ENTE R to jump direct ly to the l ocation Or number Use arrow .
38 3 4: ROTATION SENS OR Press th e up arrow key to i ncr emen t the number, the down arrow key to dec reme nt th e nu mber or en ter t he num be r dir ectl y.
39 Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess t h e up arrow key. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP 0: SEL E CT MODEL Next p.
40 From Previous 1: SYSTEM TEMP 2: ENTER LINT CLEANING FREQUENCY 1 T O 10 HOURS Next page 3: ENTER AUDIO ALERT ON TIMES 0 TO 10 4: ROTATION SENS OR 4 Press ENTE R to jump direct ly to the loc ation Or.
41 From Previ ous OFF Press t he up or down ar row key t o sel ect ON or OFF ON 5: BOAR D ADDR ESS 00 TO ZZ. Press ENTER t o acces s Pres s ENTER t o st ore new chang es.
42 Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess t h e up arrow key. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP 0: SEL E CT MODEL Next p.
43 From Previous 1: SYST EM TEMP 2: ENTER LI NT CLEA NI NG FREQ UE NCY 1 TO 10 HOUR S Next page 3: ENTE R AUDIO ALERT ON TIMES 0 TO 10 4: RO TATION SENSO R Pr e ss EN TER to jum p directl y to th e l oca ti on Or number Use arrow key 5: B OARD AD DRES S 00 TO ZZ.
44 From Previo us A_ Press the up or d ow n arr ow key to scr oll the A-Z an d 0-9 AA Press EN TER to ac ce ss Pres s ENTE R t o st ore new chan ges Press the up or d ow n arr ow key to scr oll the A-Z an d 0-9 A1 6: AUTO C Y CL E TIME OU T. 0 TO 99 MIN UTE S.
45 Ready 0:SELECT LANGUAGE Press and hol d the stop/clear key While holding th e stop/ clear k ey, pres s the up arrow k e y. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP 0: SELECT MODEL Next page Aut.
46 From Previous 1: SYSTEM TEMP 2: ENTER LINT CLEANING FREQUENCY 1 TO 10 HOURS Next page 3: ENTER AUDIO ALERT ON TIMES 0 T O 10 4: ROTATION SENSOR Press ENTER to jump direct ly to the lo cation Or number Use arrow key 5: BOARD ADDRESS 00 to ZZ.
47 From Previ ous 60 Press th e up or dow n ar row key to sc roll the A-Z an d 0-9 70 Press EN TER to acces s Pres s ENTE R to st ore new chang es AUTO C YCL E TIME OUT.
48 Adjusting Reversi ng Spin Time and Stop Tim e Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess the up arrow key.
49 1: REVERSING SETUP From Previous (A) From Prev ious (B) 0: ENTER SPIN TIME 30 TO 120 SECONDS Press the up ar row key to i ncr em en t the time, the down arrow key to decremen t the time or ente r the time directly. The time is adju st ab le from 30 to 12 0 s eco nd s.
50 Press th e up arrow key to i ncr ement the time, t he down arrow ke y to decrem ent the time or enter the time dire ct l y. Th e st op time is adj ust ab le from 5 t o 10 seco nd s.
51 Wrinkle Gu ard Audio Aler t Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess the up arrow k ey.
52 From Previous (A) From Previous (B) 2: WRINKL E GUARD SETUP ON 0: WRINKL E GUARD AUDIO ALERT Press th e up or down arrow key to sel ect ON or OFF OFF 0: WRINKL E GUARD AUDIO ALERT Press ENTER t o a.
53 Ready 0:S ELEC T LANGUAGE Press an d ho ld the stop /cl ear k ey While holding t he stop/ clear key, pr ess the up arrow key. 1: SELECT SYSTEM PARAMETERS 1 0: DRYER SETUP Next Page (A) Nex t Page (.
54 Fro m Prev ious (A) From Previous (B) 2: WRINKLE GUARD SETUP 3: STEAM INJECTION SETUP Next page.
55 ENTER 1ST ON TIME 0:01 TO 45 : 00 NOTE: Time Format is mm:ss The first time adjustment is Minutes mm: Press the up arrow ke y to incre ment the ti m e i n m i nu tes , the do w n arrow key to d ecrement the ti me in minutes or enter the tim e in minutes d irectly.
56 ENTE R 1S T OFF TIM E 5:11 TO 45 :0 0 The first tim e adjustment is Minutes mm: 0:00 From Previous Press the up arrow key t o i n crement the time in min utes, the down arrow key to decre men t the time i n min utes or enter the ti me in minutes directly.
57 20 From Previous 0:00 The fi rst time adjustment is M inutes mm: Press the up arrow key to i nc rement the time in m inutes, the down a rrow key to d ecrement the time in m inutes or enter the time in minutes dire ctly.
58 Pre ss th e up ar ro w key to in crement the t ime in secon ds, the down arrow key to decr em en t the tim e in second s or ente r the ti m e i n secon ds di rectl y. 40 4 0 0:00 Wh e n 0 tim e is e n tered, th e program will jump back to either 2: PROGRAM A-F CYCLES or 3: PROGRAM 0-40 CYCLES.
59 Progra mming A - F Cycles or 0 - 40 Cycles Ready 0:SELECT LANGUAGE The comput er must be displ ayi n g READY to enter program mode 1: SELECT SYSTEM PARAMETERS 2: PROGRAM A - F CYCLES 2: PROGRAM A - F CYCLES Next Page 2 Press and h old the stop /cl ear k ey While holding the stop/ clear key , press th e up arrow ke y.
60 SELECT A - F KEY or ENTER 0 - 40 From Prev ious SELECT CYCL E TYPE A or 0 B AUTO MANUAL 0: REV ERSE MODE Next Page (A) Nex t Page (B) B Follow this f low chart path fo r an AUTO cycl e Follow this .
61 From Previous (A) From Previous (B) OFF 1: ENTER DRY TEMP 160 TO 200ºF 160 Next Page (A) Ne xt Page (B) 0: REVERSE MODE OFF ON ENTER SPIN TIME 30 TO 120 SE C O NDS 60 ON Axial models will displa y 1: DRYIN G TEMP 160ºF ONLY, then jump to 2: ENT E R DRYNESS LEVEL.
62 Fro m Previous (A) From Previous (B) 2: ENTER DRYNESS LEVEL DRY Nex t Page (A) Nex t Page (B) 25 ENTER STOP TIME 5 TO 10 SECONDS 5 7 7 175 1 7 5 2 5 Press th e up arrow key to in crement the temp, the down arrow ke y to decremen t the temp or ent er the temp direct ly.
63 7 5 1: ENTER DRY TIME 0 TO 99 MI NUTE S 30 70 3: ENTER CYCLE ADJUSTMENT EXTRA DRY 4 5 45 2: ENTER DRY TEMP 100 TO 200 ºF Pr ess t he up arr ow k ey to incremen t the valu e, the down a rr ow ke y to decrement the value or ente r the valu e direc tly .
64 OFF ON 75 4: CONTROLLED COOL DOWN 5: ENTER COOL DOWN TIM E 0 TO 99 MI NUT ES 3: CONTROLLED COOL DOWN 175 1 7 5 ON Press th e up arrow key to i ncr em en t the temp, t he down arrow ke y to decremen t the temp or en ter the temp directly . Press the u p or down arro w key t o turn the op t i on ON or OFF.
65 70 6: ENTER COOL DOWN TEMP 70 TO 10 0 ºF 5 6 5 OFF 4: ENTER COOL DOWN TIME 0 TO 99 MINUTES 6 5 Pr ess t he up arr ow k ey to increment the time, the down a rr ow ke y to decr emen t the tim e or ente r the time dir e ctly. 5 Press ENTER to store ne w ch anges .
66 80 8 0 70 5: ENTER COOL DOWN TEMP 70 TO 100 ºF 80 8 0 Pr ess t he up arr ow k ey to increment t he temp, the d own a rr ow ke y to decr emen t the tem p or enter temp directly . 6: STEAM INJECTI ON Press the up arrow key to i ncreme nt the temp, the down arrow ke y to decremen t the temp or enter temp directl y.
67 From Previous OFF ON ENTER 1ST ON TIME 0:01 TO 45 :0 0 NOTE: Time Forma t is mm:s s Next page Pr es s the up or down arr ow key to turn the option ON or OFF.
68 From Previous 5:00 Th e se con d ti m e adjust men t is Second s :ss ENTE R 1S T OFF TIM E 5:11 TO 45 :0 0 Press the up arrow key to i nc rement the time in s econds, the down arro w key to decrem ent the time in seconds or enter t he time in s econds d irectly .
69 Press the up arrow key t o i n crement the time in min utes, the down arrow key to decre men t the time i n min utes or enter the ti me in minutes directly.
70 0:00 The fi rst time adjustment is M inutes mm: Press the up arrow key to i nc rement the time in m inutes, the down a rrow key to d ecrement the time in m inutes or enter the time in minutes dire ctly.
71 From Pre vi ous 0:00 When 0 time is e ntered, the prog r a m wi l l jump ba ck to ei t her 2: PROGRAM A-F CYCLES or 3: PROGRAM 0-40 CYCLES . ENTER 3RD ON TIME 8:21 TO 4 5:00 2: PROGRAM A-F CYCLES o.
72 Restoring Factory Def ault Se ttings Ready 0:SELE CT LANGUAGE The compu ter must be di sp laying READY to e nter prog ram mode Press an d hold t he stop/clear k ey While holding the sto p/ cle ar k ey, pres s th e up arrow ke y.
73 From Previous ENTER PASSWORD 1 2 3 CONFIRM DEFAULTS NO Press the Up or Down Arrow Key to to ggle from NO t o YES Next page.
74 From Previous YES DEFAULTS SET 4: DEFAULT SETTINGS WARNING: Pressing enter will res tore fact ory defa ult set tings , includi ng all prep rogrammed cycles an d an y adjust ments mad e t o pr ogr a m min g.
75 SECTION VII F ACT OR Y PRESET P ARAMETERS (PROGRAMS) NOTE: T o enter Program Mode, press and hold the “STOP/CLEAR” key and the “UP ARROW” key .
76 SECTION VIII PHASE 7 NON-COIN MICROPROCESSOR CONTROLLER (COMPUTER) PROGRAMMING LIMITS A. PREPROGRAMMED CYCLES 1. Automatic Drying Cycle (Patent No. 4,827,627) a .
77 B. SYSTEM P ARAMETERS (PROGRAM LOCA TIONS) 1. Cycle Adjustment V alue from 0 to 99, in increments of one (1). 2. Manually Loaded Auto Cycle (“COOL DOWN TIME”) from 0 to 99 minutes, in 1 minute increments. 3. Audio Alert 0-10. 4. Lint Cleaning Frequency 1 to 10 hours.
78 SECTION IX PHASE 7 NON-COIN AUT O CYCLE (PA TENT NO. 4,827,627) CYCLE ADJUSTMENT V ALUES IMPOR T ANT : If your particular model/dryer dryness levels are not shown in the above charts, contact the Service Department for the appropriate factors for your particular dryer .
79 SECTION X PHASE 7 NON-COIN MICROPROCESSOR CONTROLLER (COMPUTER) SYSTEM DIAGNOSTICS IMPOR T ANT : YOU MUST DISCONNECT AND LOCK OUT THE ELECTRIC SUPPL Y AND THE GAS OR STEAM SUPPL Y BEFORE ANY COVERS.
80 FLAME F AUL T – After the Phase 7 non-coin microprocessor controller (computer) has verified that the gas valve signal was present throughout the Direct Spark Ignition (DSI) purge time and the DSI proof time, the Phase 7 non-coin microprocessor controller (computer) will continue to monitor the gas valve return signal.
81 EXHAUST HIGH-LIMIT F AUL T – This routine monitors the basket (tumbler) safety over temperature switch. If the switch opens, the dryer will display “Exhaust High-Limit Fault” and will go into Fault Mode with a brief audio indication.
82 ROT A TION SENSOR FAUL T – This routine monitors the pulses from the rotational sensor input. It basically times the dwell between signals. If the time between the pulses exceeds 10-seconds, the .
83 B. F .S.S. DIAGNOSTIC CONDITIONS In the event that the Phase 7 non-coin microprocessor controller (computer) detects a fault in the Fire Suppression System (F .S.S.), the Phase 7 non-coin microprocessor controller (computer) will display the message “F .
84 C. INPUT/OUTPUT (I/O) BOARD L.E.D. INDICA T ORS 1. Inputs 1. ESTOP – (RED L.E.D.) This light emitting diode (L.E.D.) will indicate the status of the E-ST OP . If the E- STOP has been pressed, then the L.E.D. is ON. 2. GAS_V – (RED L.E.D.) This L.
85 D. KEYBOARD (TOUCH PAD) LA YOUT 1. Dot Matrix Display 2. A-F Preprogrammed Cycles 3. Stop/Pause Button 4. Start Button 5. Increment Button 6. Decrement Button 7. One T ime Auto (Dryness Level) and Manual (T imed) Cycle NOTE: Fuse 1 is for the Phase 7 non-coin microprocessor controller (computer) power rated at 1/2-amp.
86 SECTION XI CUST OMER CUST OM P ARAMETER SETTINGS This section can be used to record/document parameters and settings, personally programmed in your dryer . It is suggested that any parameter changes or customer cycles be documented here for future reference.
87 PROGRAMMED CYCLE A-F: Cycle: ______________________ Cycle T ype: AUTO Reverse Mode: __________________ (Option) Dry T emp: _________________________ Dry Level: _________________________ Cool Down T.
88 PROGRAMMED CYCLE 0-40: Cycle: ______________________ Cycle T ype: AUTO Reverse Mode: __________________ (Option) Dry T emp: _________________________ Dry Level: _________________________ Cool Down .
89 NOTES ____________________________________________________________________________________________________________________ __________________________________________________________________________.
ADC Part No. 113193 4 - 08/19/08 - 200.
An important point after buying a device American Dryer Corp. Milnor Phase 7.2.2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Dryer Corp. Milnor Phase 7.2.2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Dryer Corp. Milnor Phase 7.2.2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Dryer Corp. Milnor Phase 7.2.2 you will learn all the available features of the product, as well as information on its operation. The information that you get American Dryer Corp. Milnor Phase 7.2.2 will certainly help you make a decision on the purchase.
If you already are a holder of American Dryer Corp. Milnor Phase 7.2.2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Dryer Corp. Milnor Phase 7.2.2.
However, one of the most important roles played by the user manual is to help in solving problems with American Dryer Corp. Milnor Phase 7.2.2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Dryer Corp. Milnor Phase 7.2.2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
