EN
Graco logo
Official user manual

Graco Model 214624

16 pages·399 KB·Water Dispenser·PDF·ENDEFRITNLJA
Graco Model 214624
Table of Contents 41 sections Instructions–Parts List · HIGH PRESSURE Surge Tanks and Fluid Filters · 307296T · EN · … ShowHide
Page 1 of the Graco Model 214624 user manual — Model 237069, Series A Exposed Mounting
Page 1 · click to enlarge
Page 1

Instructions–Parts List

HIGH PRESSURE Surge Tanks and Fluid Filters

307296T

EN

For fluid surge reduction and for filtering of finishing materials.

Fluid Filters 5000 psi (350 bar, 35 MPa) Maximum Working Pressure

Model 238620, Series A Exposed Mounting Model 214724, Series E Cover Mounting Model 289310, Series A Cover Mounting

Fluid Filter, Exposed Mounting

Fluid Filter, Cover Mounting

Fluid Filter 7252 psi (500 bar, 50 MPa) Maximum Working Pressure

Model 237069, Series A Exposed Mounting

Surge Tanks (with filter) 5000 psi (350 bar, 35 MPa) Maximum Working Pressure

Model 214624, Series C Exposed Mounting Model 238623, Series A Exposed Mounting Model 214726, Series E Cover Mounting

Mastic Surge Tanks (without filter) 5000 psi (350 bar, 35 MPa) Maximum Working Pressure

Surge Tank, Exposed Mounting

Model 214623, Series A Exposed Mounting; for use with high viscosity fluids Model 214725, Series C Covered Mounting; for use with low to medium viscosity fluids

Surge Tank, Cover Mounting

1008 1009 · 1005 1008

Page 3 of the Graco Model 214624 user manual — 307296 3
Page 3 · click to enlarge
Page 3

Installation

Typical Mountings

The top of the surge tank must always be supported. See Accessories on page 13 for mounting clamps.

See Fig. 1 for typical mountings. See page 14 for the mounting hole layout.

Surge tanks must always be mounted upright, as shown in Fig. 1, not horizontally.

Install the surge tank or filter near the pump outlet. Position the surge tank so the labels face away from the pump and so the setscrews, near the top and bottom of the tank, face toward the pump.

Exposed Mountings

Graco Model 214624 — Exposed Mountings diagram (page 3)
Fig. 1 · Exposed Mountings

307296 3

Page 4 of the Graco Model 214624 user manual — 307296 4
Page 4 · click to enlarge
Page 4

Surge Tank Conversion Kits

Surge Tank Conversion Kits 238634 and 237704

Connect the surge tank to the fluid outlet (F) of the displacement pump and install the clamp in the option- al outlet (E) at the base of the air motor. See Fig. 2.

Use Conversion Kits 238634 or 237704 to add a surge tank to a pump. Kit 238634 includes surge tank 238623 (A) and clamp 238630 (B). Kit 237704 includes surge tank 214624 (A), clamp 238630 (B), and attach- ing hardware (C).

These parts are included with Conversion Kit 237704 only.

2 Model 238623 Surge Tank shown.

E

B

A

F

05927 Fig. 2

307296 4

Page 5 of the Graco Model 214624 user manual — 307296 5
Page 5 · click to enlarge
Page 5

Operation

Before operating the equipment, be sure the drain valve is closed.

Be sure the drain valve is fully closed when spraying and fully open when draining or circulating fluid to get the best results and reduce wear on the valve.

Flush the equipment with a compatible solvent to remove oil used for factory testing and rust prevention.

If you notice excessive surging at the spray gun, shut off the pump, trigger the gun to relieve fluid pressure, and open the drain valve (D) at the bottom of the surge tank. See Fig. 3. After the tank is drained, close the drain valve and resume operation.

1 Open drain valve to relieve pressure.

D

D

05913 05911 Fig. 3

307296 5

Page 6 of the Graco Model 214624 user manual — 307296 6
Page 6 · click to enlarge
Page 6

Service

Pressure Relief Procedure

Service Notes

WARNING

Clean all parts thoroughly when disassembling. Check parts carefully for damage or wear, replace as needed.

SKIN INJECTION HAZARD The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you:

Numbers in parentheses in the text refer to the parts drawings.

Check periodically for leakage from the small holes near the top and bottom of the surge tanks. If you find leakage at the holes or anywhere else, replace the seals promptly.

Before removing the end plug and adapter from the surge tank, loosen the setscrews (5) near the bottom of the tank (6). See the parts drawings on pages 7 through 12.

are instructed to relieve the pressure,

check or service any of the system equipment,

Inspect the sealing surfaces for nicks or scratches that might cause leakage. Do not damage the sealing surfaces.

or install or clean the spray tips.

1. Lock the gun trigger safety.

When reassembling filters after cleaning or servicing, be sure to install the filter support as shown in the parts drawings. Do not install it upside down.

2. Turn off the power to the pump.
3. Close any master bleed-type air valves.
4. Unlock the gun trigger safety.

WARNING

5. Hold a metal part of the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure.

Tighten all threaded connections securely. High pressure fluid can dislodge a loose connection or allow high pressure fluid to be emitted from the connection and cause serious injury.

6. Lock the gun trigger safety.
7. Place a pail under the drain valve, and open the drain valve to be sure all fluid pressure is relieved. Keep hands away from the end of the drain valve when opening it.
8. Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then loosen completely. Now clear the tip or hose.

307296 6

stop spraying,

Page 7 of the Graco Model 214624 user manual — 307296 7
Page 7 · click to enlarge
Page 7

Model 214724, Series E

Do not damage PTFE o-ring (7). Lubricate and bend into kidney shape, then push into groove.

18 19 20 21

1 174058 RING, lock 1 2 104813 PLUG, pipe, 3/8 npt 1 3 174056 BOWL, filter 1 4 171941 SPRING, conical compression 1 5 167025 STRAINER, 60 mesh (Model 214724) 1 167024 STRAINER, 30 mesh (Model 289310) 1 6 186075 SUPPORT, filter 1 7 104804 PACKING, o-ring, PTFE 1 10 104839 PLUG, pipe, 1/2 npt 1 11 102291 PIN, drive 2 12 164900 WASHER, flat 2 13 175043 LEVER 1 14 103337 PACKING, o-ring, fluoroelastomer 1

15 166697 STEM, valve 1 16 165964 NUT, packing 1 17 102310 NUT, acorn, no. 10–32 1 18 172094 SEAT, ball 1 19 165273 BALL, valve 1 20 206481 SEAT, valve 1 21 103648 PACKING, o-ring, fluoroelastomer 1 22 165274 NIPPLE, adapter 1 23 104663 PLUG, pipe, 3/4 npt 1 24 174080 MANIFOLD 1 25 101754 PLUG, pipe, 3/8 npt 1 Keep these spare parts on hand to reduce down time.

307296 7

15 121613 17

Page 8 of the Graco Model 214624 user manual — 307296 8
Page 8 · click to enlarge
Page 8

Do not damage PTFE o-ring (7). Lubricate and bend into kidney shape, then push into groove.

1 174058 RING, lock 1 2 104813 PLUG, pipe, 3/8 npt 3 3 174056 BOWL, filter 1 4 171941 SPRING, conical compression 1 5 167025 STRAINER, 60 mesh 1 6 186075 SUPPORT, filter 1 7 104804 PACKING, o-ring, PTFE 1 8 24C497 MANIFOLD, paint filter 1

9 223960 BALL VALVE, see 306861 for parts 1 10 104839 PLUG, pipe, 1/2 npt 1 26 155665 UNION, adapter 1 27 205448 COUPLING, swivel; 3/8 npsm(f) 1 28 186447 TUBE, drain; nylon; 1/4 in. (0.6 mm) ID; 5 in. (127 mm) 1

307296 8

Page 9 of the Graco Model 214624 user manual — 307296 9
Page 9 · click to enlarge
Page 9

Model 237069 Includes items 1–26

Do not damage PTFE o-ring (7). Lubricate and bend into kidney shape, then push into groove.

1 174058 RING, lock 1 2 104813 PLUG, pipe, 3/8 npt 3 3 174056 BOWL, filter 1 4 171941 SPRING, conical compression 1 5 167025 STRAINER, 60 mesh 1 6 186075 SUPPORT, filter 1 7 104804 PACKING, o-ring, PTFE 1

8 24C497 MANIFOLD, paint filter 1 9 224774 DRAIN VALVE 1 10 100737 PLUG, pipe, 1/2 npt 1 26 156296 NIPPLE; 3/8 npt x 1/8 npt 1

307296 9

Page 10 of the Graco Model 214624 user manual — 307296 10
Page 10 · click to enlarge
Page 10

Model 214624, Series C Includes items 1–16, 31, 33, 34

Graco Model 214624 — Model 214624, Series C Includes items 1–16, 31, 33, 34 diagram (page 10)
Fig. 2 · Model 214624, Series C Includes items 1–16, 31, 33,…

Model 214726, Series E Includes items 1–13, 17–32, 34

Do not damage PTFE o-ring (13). Lubricate and bend into kidney shape, then push into groove.

1 174064 PLUG, end 1 2 104805 RING, backup, PTFE 2 3 166612 PACKING, o-ring, PTFE 2 5 111463 SETSCREW,1/4–20 x 3/8” 2 6 none TANK, accumulator not sold separately 1 7 174059 ADAPTER, filter 1 8 171941 SPRING, conical compression 1 9 167025 STRAINER, 60 mesh 1 10 186075 SUPPORT, filter 1 11 174058 RING, lock 1 12 174068 ADAPTER, accumulator 1 13 104804 PACKING, o-ring, PTFE 1 14 24C497 MANIFOLD, paint filter 1 15 104813 PLUG, pipe, 3/8 npt 2 16 210658 BALL VALVE, see 306861 for parts 1 17 164900 WASHER, flat 2 18 175043 LEVER 1 19 103337 PACKING, o-ring, fluoroelastomer 1 20 166697 STEM, valve 1

21 165964 NUT, packing 1 22 102310 NUT, acorn, No. 10–32 1 23 174080 MANIFOLD 1 24 101754 PLUG, pipe, 3/8 npt 1 25 172094 SEAT, ball 1 26 165273 BALL, valve 1 27 206481 SEAT, valve 1 28 103648 PACKING, o-ring, fluoroelastomer 1 29 165274 NIPPLE, adapter 1 30 104663 PLUG, pipe, 3/4 npt 1 31 104839 PLUG, 1/2 npt 1 32 102291 PIN, drive 2 33 155665 UNION, adapter 1 34 169579 LABEL, warning 1

Replacement Danger and Warning labels, tags and cards

are available at no cost.

307296 10

Page 11 of the Graco Model 214624 user manual — 307296 11
Page 11 · click to enlarge
Page 11

Do not damage PTFE o-ring (13). Lubricate and bend into kidney shape, then push into groove.

Torque to 150 ft–lb (200 N.m).

Torque to 40 in–lb (4.5 N.m).

1 174064 PLUG, end 1 2 104805 RING, backup, PTFE 2 3 166612 PACKING, o-ring, PTFE 2 5 111463 SETSCREW,1/4–20 x 3/8” 2 6 none TANK, accumulator not sold separately 1 7 174059 ADAPTER, filter 1 8 171941 SPRING, conical compression 1 9 167025 STRAINER, 60 mesh 1 10 186075 SUPPORT, filter 1 11 174058 RING, lock 1 12 174068 ADAPTER, accumulator 1 13 104804 PACKING, o-ring, PTFE 1 14 24C497 MANIFOLD, paint filter 1

15 104813 PLUG, pipe, 3/8 npt 2 16 238612 BALL VALVE, see 306861 for parts 1 31 104839 PLUG, 1/2 npt 1 33 155665 UNION, adapter 1 34 169579 LABEL, warning 1 35 205448 COUPLING, swivel; 3/8 npsm(f) 1 36 186447 TUBE, drain; nylon; 1/4 in. (0.6 mm) ID; 5 in. (127 mm) 1

Replacement Danger and Warning labels, tags and cards

are available at no cost.

307296 11

Page 12 of the Graco Model 214624 user manual — 307296 12
Page 12 · click to enlarge
Page 12

Do not damage PTFE o-ring (9). Lubricate and bend into kidney shape, then push into groove.

Model 214725, Series C Includes items 1–9, 11, 13–29

Torque to 150 ft–lb (200 N.m).

Torque to 40 in–lb (4.5 N.m).

1 174064 PLUG, end 1 2 104805 RING, backup, PTFE 2 3 166612 PACKING, o-ring, PTFE 2 5 111463 SETSCREW, 1/4–20 x 3/8” 2 6 none TANK, accumulator not sold separately 1 7 174058 RING, lock 1 8 174068 ADAPTER, accumulator 1 9 104804 PACKING, o-ring, PTFE 1 10 174060 MANIFOLD, accumulator 1 11 104663 PLUG, pipe, 3/4 npt 1 12 210658 BALL VALVE, see 306861 for parts 1 13 175043 LEVER 1 14 104839 PLUG, 1/2 npt 1 15 103337 PACKING, o-ring, fluoroelastomer 1 16 166697 STEM, valve 1 17 165964 NUT, packing 1

18 102310 NUT, acorn, No. 10–32 1 19 174080 MANIFOLD 1 20 101754 PLUG, pipe, 3/8 npt 1 21 172094 SEAT, ball 1 22 165273 BALL, valve 1 23 206481 SEAT, valve 1 24 103648 PACKING, o-ring, fluoroelastomer 1 25 165274 NIPPLE, adapter 1 27 102291 PIN, drive 2 28 164900 WASHER, flat 2 29 169579 LABEL, warning 1

Replacement Danger and Warning labels, tags and cards

are available at no cost.

307296 12

Page 13 of the Graco Model 214624 user manual — 307296 13
Page 13 · click to enlarge
Page 13

Accessories

Use Only Genuine Graco Parts and Accessories

SURGE TANK CLAMPS

PTFE SEALS

238630 For surge tanks mounted in the fluid outlet of the displacement pump. Install the clamp in the optional outlet at the base of the air motor. Requires 100902 screw, 100016 lockwasher and 100015 nut.

For ball valves and drain valves.

104892 to replace 103648 fluoroelastomer seal 104893 to replace 103337 fluoroelastomer seal

STAINLESS STEEL SCREENS

167024 595 micron (30 mesh) 167025 250 micron (60 mesh) 167026 149 micron (100 mesh) 167027 75 micron (200 mesh)

172865 For surge tanks mounted in the optional fluid outlet of Bulldog or King pumps when used with a riser tube. Attach the clamp to the top of the air motor shield. Requires 100902 screw, 100016 lockwasher, 100015 nut, and two 100270 screws.

307296 13

100016 100015 100902

Page 14 of the Graco Model 214624 user manual — 307296 14
Page 14 · click to enlarge
Page 14

Technical Data

Mounting Hole

Layout

Category Data

Model 237069: 7252 psi (500 bar, 50 MPa) All Other Models: 5000 psi (350 bar, 35 MPa)

For mounting square base surge tanks and filters on a drum cover or other support.

Weight Model 214623: 30 lb (13 kg) Model 214624: 31.5 lb (14 kg) Model 214724: 13 lb (6 kg) Model 214725: 34 lb (15 kg) Model 214726: 34 lb (15 kg) Model 237069: 10.5 lb (4.5 kg) Model 238620: 10.5 lb (4.5 kg) Model 238623: 31.5 lb (14 kg) Model 289310: 13 lb (6 kg)

2.38” (60 mm) dia.

15 oz. (450 ml)

1.06” (27 mm)

Filter Area 18 in2 (120 cm2)

Wetted Parts Stainless steel, zinc-plated steel, nylon, PTFE, fluoroelastomer

0.312” (8.12 mm) dia.

1.06” (27 mm)

307296 14

Maximum Working Pressure · Surge Tank Volume

Page 15 of the Graco Model 214624 user manual — 307296 15
Page 15 · click to enlarge
Page 15

Dimensions

Graco Model 214624 — Dimensions diagram (page 15)
Fig. 3 · Dimensions

* For models 238620 and 238623, add approximately 6 in. (152 mm) to the “A” dimension to account for the drain tube and fitting.

Graco Model 214624 — Dimensions diagram (page 15)
Fig. 4 · Dimensions

J

F

J

E

G

Graco Model 214624 — J diagram (page 15)
Fig. 5

Dimensions 238620 237069 214724 & 289310 214624 & 238623 214726 214623 214725

F 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f) 3/4 npt(f)

H 3/8 npt(f) 3/8 npt(f) 3/8 npt(f) 3/4 npt(f)

J 1/2 npt(f) 1/2 npt(f) 1/2 npt(f) 1/2 npt(f) 1/2 npt(f) 3/4 npt(f) 1/2 npt(f)

K 3/8 npt(f) 3/8 npt(f) 3/4 npt(f) 3/8 npt(f) 3/4 npt(f) 3/4 npt(f)

L 3/8 npt(m) 1/8 npt(f) 1/4 npt(m) 3/8 npt(f) 1/4 npt(m) 3/8 npt(f) 1/4 npt(m)

307296 15

1005 1008

Page 16 of the Graco Model 214624 user manual — www.graco.com
Page 16 · click to enlarge
Page 16

The Graco Standard Warranty

Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub- stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais- sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers

to identify the distributor closest to you:

1–800–328–0211 Toll Free 612–623–6921 612–378–3505 Fax

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents

Original instructions. This manual contains English. MM 307296

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS MN 55440–1441 USA

Copyright 1978, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

307296 16

Revised April 2013

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Graco Model 214624

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco Model 214624

Be the first to ask — other owners or our team will answer.

Original document

Graco Model 214624 manual PDF

16 pages·399 KB·Water Dispenser·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…