EN
Graco logo
Official user manual

Graco 310554V

46 pages·1.9 MB·Water Dispenser·PDF·ENDEFRITNLJA
Graco 310554V
Table of Contents 69 sections List of Models · Tool Mounted Dispensers · Cable Assemblies · Warnings · … ShowHide
List of Modelsp.2Tool Mounted Dispensersp.2Cable Assembliesp.2Warningsp.4Unpacking and Repackingp.8Unpacking the Productp.8Repair and Repacking the Productp.8PrecisionSwirl Overviewp.9PrecisionSwirl Capabilitiesp.9PrecisionSwirl in Basic Robotic Systemp.10Installing the Control Assemblyp.11Preparing to Install the Control Assemblyp.11Mounting the Control Assemblyp.11Mounting the Control Assembly (continued)p.12Installationp.13Grounding the Control Assemblyp.13Connecting the Control Assembly to a Power Sourcep.14Connecting the Control Assembly to a Power Source (continued)p.15Checking Resistance Between the Control Assembly and the True Earth Groundp.15Installing the Dispense Valvep.16Mounting the Dispense Valvep.16Connecting Air Lines to Dispense Valvep.16Connecting Material Hose to Dispense Valvep.16Installing Cable Assembliesp.17Connecting the Motor Control Cablep.17Connecting the Motor Control Cable (continued)p.18Connecting the Automatic Control Cablep.19Verifying Ground Continuityp.20Verifying Ground Continuityp.20Adjusting the Orbital Dispenserp.20Inspecting the Orbital Dispenserp.20Grounding the Systemp.20PrecisionSwirl Module Operationp.21Reading the PrecisionSwirl Control Assembly Controls and Indicatorsp.21Setting Operation Modesp.22Analyzing Causes for a Motor Fault Alarmp.23Adjusting Orbital Dispenser Motor Speedp.24Troubleshootingp.25Control Assembly Servicep.26Servicing the Control Assemblyp.26Lamp Button and Switch Removalp.26Lamp Button and Switch Replacementp.26Light Bulb Removalp.26Light Bulb Replacementp.26MAIN Power Switch Removalp.27MAIN Power Switch Replacementp.27Potentiometer Removalp.28Potentiometer Replacementp.28Panel Assembly Servicep.29Swirl Control Board Removalp.30Swirl Control Board Replacementp.30RFI Filter Removalp.31RFI Filter Replacementp.31Relay Removalp.32Relay Replacementp.32Fuse Removalp.33Fuse Replacementp.33Control Assembly Partsp.34Accessory Partsp.40Motor Control Cable Assembliesp.40Torsional Motor Control Cable Assembliesp.41Robot Interface Cable Assemblyp.42Dispenser Valve Adapter Fittingsp.42Wiring Diagramsp.43Motor Controller Wiring, Lines 200-238p.43Motor Controller Wiring, Lines 250-288p.44Technical Datap.45Graco Standard Warrantyp.46Graco Informationp.46
Page 1 of the Graco 310554V user manual — POWER MOTOR FAULT RUN
Page 1 · click to enlarge
Page 1

Instructions - Parts List

PrecisionSwirl ™ Module

ENG

An orbital dispenser used to apply sealant and adhesive materials for a variety of applications.

Part No. 241658, 234029, 289911 and 289912

3500 psi (24.1 MPa, 241 bar) Maximum Fluid Working Pressure

Graco 310554V — Part No. 241658, 234029, 289911 and 289912 diagram (page 1)
Fig. 1 · Part No. 241658, 234029, 289911 and 289912

See page 2 for List of Models.

U.S. Patent No. 6,499,673 EU Patent No. 0852160

Graco 310554V — Part No. 241658, 234029, 289911 and 289912 diagram (page 1)
Fig. 2 · Part No. 241658, 234029, 289911 and 289912

POWER MOTOR FAULT RUN

MAIN RUN / ENABLE

CONTROL SELECT

MANUAL SPEED CONTROL

AUTOMATIC MANUAL

PrecisionSwirl Orbital Dispenser 243402 and 243403

8037B PrecisionSwirl Control Assembly

918616 289261 and 289262

PrecisionSwirl Orbital Dispenser

Page 2 of the Graco 310554V user manual — Part No. 617829
Page 2 · click to enlarge
Page 2

List of Models

Tool Mounted Dispensers

Part No. 241658, Series A

PrecisionSwirl Orbital Dispenser and Control Assembly Kit includes 233123, 243403, 617829, 617870 and 918616.

Part No. 234029, Series A

PrecisionSwirl Orbital Dispenser and Control Assembly Kit includes 233123, 243402, 617829, 617870 and 918616.

Part No. 289911, Series A

PrecisionSwirl Orbital Dispenser and Control Assembly Kit includes 233123, 289261, 617829, 617870 and 918616.

Part No. 289912, Series A

PrecisionSwirl Orbital Dispenser and Control Assembly Kit includes 233123, 289262, 617829, 617870 and 918616.

Part No. 918616, Series D

Cable Assemblies

Part No. 233125

6 ft (1.8 m) Motor Extension Cable Assembly

8130B

Part No. 233124

9 ft (2.7 m) Motor Extension Cable Assembly

Part No. 233123

15 ft (4.6 m) Motor Extension Cable Assembly

Part No. 617870

55 ft (16.8 m) Motor Extension Cable Assembly

Part No. 617829

40 ft (12.2 m) Robot Interface Cable Assembly

List of Models · Tool Mount · PrecisionSwirl Control Assembly

Page 3 of the Graco 310554V user manual — Table of contents
Page 3 · click to enlarge
Page 3

Table of contents

List of Modelsp.2Tool Mounted Dispensersp.2Cable Assembliesp.2Warningsp.4Unpacking and Repackingp.8Unpacking the Productp.8Repair and Repacking the Productp.8PrecisionSwirl Overviewp.9PrecisionSwirl Capabilitiesp.9PrecisionSwirl in Basic Robotic Systemp.10Installing the Control Assemblyp.11Preparing to Install the Control Assemblyp.11Mounting the Control Assemblyp.11Mounting the Control Assembly (continued)p.12Installationp.13Grounding the Control Assemblyp.13Connecting the Control Assembly to a Power Sourcep.14Connecting the Control Assembly to a Power Source (continued)p.15Checking Resistance Between the Control Assembly and the True Earth Groundp.15Installing the Dispense Valvep.16Mounting the Dispense Valvep.16Connecting Air Lines to Dispense Valvep.16Connecting Material Hose to Dispense Valvep.16Installing Cable Assembliesp.17Connecting the Motor Control Cablep.17Connecting the Motor Control Cable (continued)p.18Connecting the Automatic Control Cablep.19Verifying Ground Continuityp.20Verifying Ground Continuityp.20Adjusting the Orbital Dispenserp.20Inspecting the Orbital Dispenserp.20Grounding the Systemp.20PrecisionSwirl Module Operationp.21Reading the PrecisionSwirl Control Assembly Controls and Indicatorsp.21Setting Operation Modesp.22Analyzing Causes for a Motor Fault Alarmp.23Adjusting Orbital Dispenser Motor Speedp.24Troubleshootingp.25Control Assembly Servicep.26Servicing the Control Assemblyp.26Lamp Button and Switch Removalp.26Lamp Button and Switch Replacementp.26Light Bulb Removalp.26Light Bulb Replacementp.26MAIN Power Switch Removalp.27MAIN Power Switch Replacementp.27Potentiometer Removalp.28Potentiometer Replacementp.28Panel Assembly Servicep.29Swirl Control Board Removalp.30Swirl Control Board Replacementp.30RFI Filter Removalp.31RFI Filter Replacementp.31Relay Removalp.32Relay Replacementp.32Fuse Removalp.33Fuse Replacementp.33Control Assembly Partsp.34Accessory Partsp.40Motor Control Cable Assembliesp.40Torsional Motor Control Cable Assembliesp.41Robot Interface Cable Assemblyp.42Dispenser Valve Adapter Fittingsp.42Wiring Diagramsp.43Motor Controller Wiring, Lines 200-238p.43Motor Controller Wiring, Lines 250-288p.44Technical Datap.45Graco Standard Warrantyp.46Graco Informationp.46
Page 4 of the Graco 310554V user manual — WARNING
Page 4 · click to enlarge
Page 4

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

  • EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in serious injury.
  • This equipment is for professional use only.
  • Read all instruction manuals, warnings, tags, and labels before operating the equipment.
  • Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco distributor.
  • Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
  • Check the equipment daily. Repair or replace worn or damaged parts immediately.
  • Do not exceed the maximum fluid working pressure of 3500 psi (241 bar, 24.1 MPa) to the dispenser or manifold.
  • Never exceed the recommended working pressure or the maximum air inlet pressure stated on your pump or in the Technical Data section on page 63.
  • Be sure that all spray/dispensing equipment and accessories are rated to withstand the maximum working pressure of the pump. Do not exceed the maximum working pressure of any component or accessory used in the system.
  • Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
  • Do not expose Graco standard hoses to temperatures above 180° F (82° C) or below -40° F (-40° C).
  • Do not use the hoses to pull the equipment.
  • Use only fluids and solvents that are compatible with the equipment wetted parts. See the Technical Data sections of all the equipment manuals. Read the fluid manufacturer’s warnings.
  • Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and solvent manufacturers.
  • Comply with all applicable local, state, and national fire, electrical, and other safety regulations.
Page 5 of the Graco 310554V user manual — WARNING
Page 5 · click to enlarge
Page 5

WARNING

  • SKIN INJECTION HAZARD Spray from the applicator, hose leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.
  • Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate surgical treatment.
  • Do not point the applicator at anyone or at any part of the body.
  • Do not put hand or fingers over the front of the applicator.
  • Do not stop or deflect fluid leaks with your hand, body, glove, or rag.
  • Follow the Pressure Relief Procedure from manual 309403 whenever you are instructed to: relieve pressure; stop dispensing; clean, check, or service the equipment; or install or clean a nozzle.
  • Tighten all the fluid connections before operating the equipment.
  • Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately. Permanently coupled hoses cannot be repaired; replace the entire hose.
  • Always wear eye protection and protective clothing when installing, operating, or servicing this dispensing equipment.
  • Do not remove or modify any part of the applicator; this can cause a malfunction and result in serious bodily injury.
  • Use extreme caution when cleaning or changing nozzles. If the nozzle clogs while applying material, Always follow the Pressure Relief Procedure from manual 309403, then remove the nozzle to clean it.
  • Never wipe off build–up around the nozzle or inlet cap until pressure is fully relieved.
  • FIRE AND EXPLOSION HAZARD Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and result in fire or explosion and serious injury.
  • Ground the equipment and the object being dispensed. See Grounding on page 20.
  • Ground the equipment and the object being sprayed, and all other electrically conductive objects in the dispense area. Proper grounding dissipates static electricity generated in the equipment. See Grounding on page 20.
  • Do not use this equipment with flammable liquids.
  • Keep the dispense area free of debris, including solvent, rags, and gasoline.
  • If there is any static sparking or you feel an electric shock while using the equipment, stop dispensing immediately . Do not use the equipment until you have identified and corrected the problem.
  • Be sure all electrical work is performed by a qualified electrician only.
  • Have any checks, installation, or service to electrical equipment performed by a qualified electrician only.
  • Be sure all electrical equipment is installed and operated in compliance with applicable codes.
  • Be sure power is disconnected when servicing and repairing equipment.
  • Before operating the equipment, extinguish all open flames or pilot lights in the dispense area.
  • Do not smoke in the dispensing area.
  • Keep liquids away from the electrical components
  • Disconnect electrical power at the main switch before servicing the equipment.
Page 6 of the Graco 310554V user manual — WARNING
Page 6 · click to enlarge
Page 6

WARNING

  • TOXIC FLUID OR FUMES HAZARD Hazardous fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, swallowed, or inhaled.
  • Provide fresh air ventilation to avoid the buildup of vapors from the fluid being dispensed.
  • Know the specific hazards of the fluid you are using.
  • Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state, and national guidelines.
  • Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and solvent manufacturer.
  • Avoid exposure to heated material fumes.
Page 7 of the Graco 310554V user manual — Warnings
Page 7 · click to enlarge
Page 7
Page 8 of the Graco 310554V user manual — Service by an Authorized Graco Distributor
Page 8 · click to enlarge
Page 8

Unpacking and Repacking

Unpacking the Product

2. Place the orbital dispenser and any loose or damaged parts in the same bag and box used in the original shipment. Fill the box with filler material to minimize the possibility of damage.

The PrecisionSwirl orbital dispenser and control assem- bly were carefully packaged for shipment by Graco. When the package arrives, perform the following proce- dure to unpack the units:

3. Seal the box tightly to protect its contents and prevent shipping damage.
1. Inspect the shipping box carefully for shipping damage. Contact the carrier promptly if damage is discovered.
4. Insure your shipment for the proper replacement value of its contents.
5. Ship the orbital dispenser freight prepaid to your authorized Graco distributor for service.
2. Unseal the box and inspect the contents carefully. There should not be any loose or damaged parts in the bag.
3. Compare the packing slip against all items included in the box. Any shortages or other inspection problems should be reported immediately.
4. Store the box and packing materials in a safe place for future use. Graco recommends that all packing materials be saved in case the unit needs to be shipped again.

Repair and Repacking the Product

When the PrecisionSwirl orbital dispenser requires ser- vice, it is the purchaser’s responsibility to have the unit repaired. As an option, the purchaser can have the unit repaired by an authorized Graco distributor. For addi- tional information, read the following subsections.

On–site Service

PrecisionSwirl components are customarily serviced by the purchaser or an authorized Graco technician. When service is required, follow the Service procedures in this manual.

Service by an Authorized Graco Distributor

The PrecisionSwirl orbital dispenser can be serviced by an authorized Graco distributor after completing a Return Goods Authorization (RGA) form. The purchaser must re–package and ship the orbital dispenser to the Graco distributor. When repacking the orbital dispenser, perform the following steps:

1. Retrieve the original box and packing materials for shipment.

Unpacking and Repacking

Page 9 of the Graco 310554V user manual — 8128B
Page 9 · click to enlarge
Page 9

PrecisionSwirl Overview

PrecisionSwirl Capabilities

The PrecisionSwirl orbital dispenser is regulated through the control assembly. The orbital dispenser is used to swirl sealant and adhesives in a variety of appli- cations.

In a basic robotic system, the control assembly serves as the interface between the robot controller and the orbital dispenser via an interface cable. Refer to Robot Interface Cable Assembly on page 52.

The orbital dispenser is operated either manually from the control assembly or automatically from a robot con- troller where the orbital dispenser is programmed to apply material continuously, or at interrupted intervals, or both. The orbital dispenser can be stopped, started, and regulated to suit the application, making high quality swirl patterns that hold form after the material is dis- pensed.

The orbital dispenser applies a continuous swirled bead of material directly on components in targeted areas, such as the hem flanges on car doors, the interior seams of the chassis, and on the fixed glass openings of autos.

Bead profile is “pre–shaped” in a uniform pattern of overlaid circular loops (see FIG. 2). Bead shape is affected by nozzle size, material composition, flow rate, stand off distance, and orbital dispenser motor speed. The oscillating nozzle on the orbital dispenser can apply an accurate swirled bead of material on vertical and hor- izontal planes.

8128B

The orbital dispenser is small enough to apply sealant and adhesives on any type of surface or material, and can be directed on any programmable path, including: a series of crevices, creases, or around a maze of straight lines, sharp angles, contours, curves, corners, and openings.

The material source for the orbital dispenser is com- monly supplied via a dual ram pump fluid supply system, which can be equipped with filters, temperature condi- tioning, and a fluid supply header.

PrecisionSwirl Overview

Page 10 of the Graco 310554V user manual — PrecisionSwirl in Basic Robotic System
Page 10 · click to enlarge
Page 10

PrecisionSwirl in Basic Robotic System

4 Automatic control cable (PrecisionSwirl). Also called robot interface cable in this manual. 5 6, 9, or 15 ft (1.8, 2.7, or 4.6 m) flexible motor cable for robot mounting (PrecisionSwirl) 6 55 ft (16.8 m) motor cable (PrecisionSwirl) 7 Dispense valve (not included) 8 Sealer robot 9 Robot controller 10 Fluid supply system 11 Fluid supply header

FIG. 3 shows the PrecisionSwirl components in a basic robotic system. The following list identifies the Preci- sionSwirl components:

No. Description 1 Control assembly (PrecisionSwirl) 2 Orbital dispenser (PrecisionSwirl)

Graco 310554V — PrecisionSwirl in Basic Robotic System diagram (page 10)
Fig. 3 · PrecisionSwirl in Basic Robotic System

PrecisionSwirl Overview

Page 11 of the Graco 310554V user manual — Preparing to Install the Control Assembly
Page 11 · click to enlarge
Page 11

Installing the Control Assembly

Installing the Control Assembly

To install the control assembly:

Mounting the Control Assembly

  • Prepare to install the control assembly
1. Select a location to mount the PrecisionSwirl control assembly. Keep the following in mind:
  • Mount the control assembly

Allow sufficient space for mounting and using the equip- ment:

  • Ground the control assembly (electrically)
  • Connect control assembly to a power source
  • Mount the control assembly approximately 24-67 in. (0.6-1.7 m) above the floor.
  • Check resistance between the control assembly and a true earth ground.
  • Make sure all cables reach components without strain .
  • Make sure there is sufficient space for repair, maintenance, and operation of the robot and applicator. The National Electrical Code requires 3 ft (91.4 cm) of open space in front of the control assembly.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

  • Make sure there is sufficient clearance around the control assembly for running fluid lines and cables to other components.

Preparing to Install the Control Assembly

  • Make sure there is easy and safe access to an appropriate electrical power source.
2. Secure the PrecisionSwirl control assembly with four 1/4 in. bolts through the 0.31 in. diameter holes in the mounting flanges. See F IG . 4 for the mounting hole spacing in the control assembly.

Before installing the control assembly:

  • See component manuals for specific data on component requirements, such as a robot. Data presented here pertains to the PrecisionSwirl control assembly only.
  • Have all applicable documentation available during installation.
  • Use only the Graco PrecisionSwirl control assembly with the PrecisionSwirl applicator.

EQUIPMENT MISUSE HAZARD The PrecisionSwirl control assembly weighs approxi- mately 23.5 lb (10.7 kg). Exercise care when mounting and handling the control assembly to prevent equip- ment damage or personal injury.

Page 12 of the Graco 310554V user manual — Mounting the Control Assembly (continued)
Page 12 · click to enlarge
Page 12

Installing the Control Assembly

Mounting the Control Assembly (continued)

Graco 310554V — Mounting the Control Assembly (continued) diagram (page 12)
Fig. 4 · Mounting the Control Assembly (continued)
Page 13 of the Graco 310554V user manual — L2/N
Page 13 · click to enlarge
Page 13

Installation

Grounding the Control Assembly

CAUTION

If power and grounding connections are not done properly, the equipment may be damaged and the warranty will be voided.

  • FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD To reduce the risk of fire, explosion, or electric shock:
  • The PrecisionSwirl control assembly must be electrically connected to a true earth ground; the ground in the electrical system may not be sufficient.
  • All wires used for grounding must be 8 AWG (8.36 mm 2 ) minimum.
  • A qualified electrician must complete all grounding and wiring connections.
  • Refer to your local code for the requirements for a “true earth ground” in your area.
  • Also read and follow the warnings on page 4.

CAUTION

To help avoid damage to equipment, make sure that the robot and PrecisionSwirl equipment are grounded to the same point.

Connect a ground wire from the GND terminal in the PrecisionSwirl control assembly (shown in FIG. 5) to a true earth ground.

'.$

'.$

'.$

'.$

'.$

,,.0% 6!# 0( (:

'.$

L2/N

Show 131 more labels / short text on this page
Installation · · · · · · · · · · · · · * · * · * · * · * · * · * · #2 #2 #2 · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · PE/GND Power Terminals
Page 14 of the Graco 310554V user manual — 8027A
Page 14 · click to enlarge
Page 14

Connecting the Control Assembly to a Power Source

Perform the following procedure to connect the control assembly to a power source.

To connect the control assembly to the electrical source:

1. Shut off system power at the main circuit breaker.
2. Locate the opening on the bottom of the control assembly, labeled POWER SUPPLY. See F IG . 6.

ELECTRIC SHOCK HAZARD Do not connect the PrecisionSwirl control assembly to a power source unless you are a trained electrician. Failure to follow standard procedures or to observe the necessary precautions could result in serious bodily injury or equipment damage.

CAUTION

0/7%2 3500,9 !54/-!4)##/.42/,

If power and grounding connections are not done properly, the equipment may be damaged and the warranty will be voided.

8027A

7/8 in. Diameter power supply entry

Have a qualified electrician connect the PrecisionSwirl control assembly to a grounded electrical source that has the following required service ratings:

3. Using 16 AWG wire or larger, connect electrical power to L1 (hot), L2 (neutral) power terminals in the PrecisionSwirl control assembly. See F IG . 8.
4. Use a cord grip to seal the area where wires enter the control assembly.

Any fitting that is used to connect a power cord (or conduit for power wiring) to the control assembly must provide a liquid–tight seal.

Full Load Amps 0.42 at 120 Vac

Circuit Breaker 5 Amp

Power to the control assembly must be supplied from a source with a lockable–off disconnect switch, or by use of a cord with a plug–and–socket connection to the source of power.

5. Apply system power at the main circuit breaker.
6. Move the POWER switch to the ON position, applying power to the control assembly.
Show 8 more labels / short text on this page
Installation · -/4/2 · #!",% · #!",% · Description Requirements · Vac 100-240 · Hz 50/60 · Phase 1
Page 15 of the Graco 310554V user manual — L2/N
Page 15 · click to enlarge
Page 15

Connecting the Control Assembly to a Power Source (continued)

'.$

'.$

'.$

'.$

'.$

,,.0% 6!# 0( (:

'.$

L2/N

Checking Resistance Between the Control Assembly and the True Earth Ground

FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD To reduce the risk of fire, explosion, or electric shock, the resistance between the supply unit components and true earth ground must be less than 0.25 ohms.

Have a qualified electrician check the resistance between each system component and the true earth ground. The resistance must be less than 0.25 ohms. If the resistance is greater than 0.25 ohms, a different ground site may be required. Do not operate the Preci- sionSwirl module until the problem is corrected.

Show 131 more labels / short text on this page
Installation · · * · · · · · · · · · · · · * · * · * · * · * · * · * · #2 #2 #2 · * · * · * · * · * · * · * · * · * · * · * · * · * · * · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · PE/GND Power Terminals
Page 16 of the Graco 310554V user manual — Connecting Material Hose to Dispense Valve
Page 16 · click to enlarge
Page 16

Installing the Dispense Valve

Installing the Dispense Valve

To install the dispense valve:

  • Mount the dispense valve
  • Connect the air lines
  • Connect material hose

Mounting the Dispense Valve

Attach the dispense valve to the mounting bracket on a stationary support or robotic arm, using two socket head screws (38) and flat washers (39).

The customer must provide a four–way pneumatic valve, activated by a separate on/off dispense sig- nal via the robot, to control material flow.

Connecting Air Lines to Dispense Valve

Securely connect air lines to dispense valve air ports (F). Make sure to connect the appropriate air lines to the appropriate ports.

Connecting Material Hose to Dispense Valve

Securely connect the material hose to dispense valve inlet port (A).

Refer to Dispense Valve manuals 308876 and 309376.

Page 17 of the Graco 310554V user manual — 8027A
Page 17 · click to enlarge
Page 17

Installing Cable Assemblies

  • Keep cables from rubbing against other components or machinery.

CAUTION

Always make connections to the control assembly with power turned off.

  • If a lot of robot wrist motion is required, leave sufficient cable length to allow for the motion, avoiding any cable droops that may interfere with the machinery or substrate.

Connecting the Motor Control Cable

  • Route and secure the 7 in. motor cable to minimize any movement. The 7 in. motor cable is not intended to handle severe flexing motions.

Motor control cables are supplied in four lengths, 6 ft (1.8 m), 9 ft (2.7 m), 15 ft (4.6 m), and 55 ft (16.8). The 55 ft cable may be used by itself. The 6 ft, 9 ft, and 15 ft cable must be used with the 55 ft cable.

  • Cable ties should only be used to loosely bundle hoses together. Do not tighten cable ties to the point where cable movement is restricted.

To connect the motor cable between the control assem- bly and the orbital dispenser, do the following:

1. Locate the receptacle on the bottom of the control assembly that is labeled MOTOR CABLE. See F IG . 8.

0/7%2 3500,9 !54/-!4)##/.42/,

8027A

2. Connect the orbital dispenser cable (55 ft) to the MOTOR CABLE receptacle. See F IG . 9.
3. Check the connections to ensure the cable is connected correctly.
4. Route the motor control cable and conform to the following cable routing requirements:
  • Avoid a bend radius of less than 5 in. (12.7 cm).
  • Avoid pinch points.
  • Avoid cable pulling or stretching.
Show 5 more labels / short text on this page
Installing Cable Assemblies · -/4/2 · #!",% · #!",% · Motor cable receptacle
Page 18 of the Graco 310554V user manual — Connecting the Motor Control Cable (continued)
Page 18 · click to enlarge
Page 18

Connecting the Motor Control Cable (continued)

0/7%2 -/4/2&!5,4 25.

Motor Control Cable (15 ft)

-!). 25.%.!",%

#/.42/,3%,%#4

-!.5!,30%%$#/.42/,

!54/-!4)# -!.5!,

Motor Control Cable (55 ft)

Installing Cable Assemblies · ti0657B

Page 19 of the Graco 310554V user manual — CAUTION
Page 19 · click to enlarge
Page 19

Connecting the Automatic Control Cable

5. Check the connections to ensure the cable is connected correctly.

Automatic control cable receptacle

CAUTION

Graco 310554V — CAUTION diagram (page 19)
Fig. 5

Always make connections to the control assembly with power turned off.

The PrecisionSwirl control assembly is provided with a 9–pin receptacle for the robot interface cable.

Any wiring from an external source, such as a robot controller, must follow the robot manufacturer’s instructions and must comply with the appropriate codes and standards.

To connect the automatic control cable (P/N 617829) between the control assembly and the robot, perform the following steps:

Graco 310554V — CAUTION diagram (page 19)
Fig. 6

Enable The 24V enable signal starts the orbital dis- penser motor.

1. Locate the receptacle on the bottom of the control assembly that is labeled AUTOMATIC CONTROL CABLE. See F IG . 10.

This 0-10 VDC analog signal is used to adjust the motor speed. (0-10 VDC = 6600-24,000 RPM)

2. Connect the cable assembly to the AUTOMATIC CONTROL CABLE receptacle in F IG . 10.

The alarm relay activates when the motor speed drops below 1500 RPM or does not start. The relay contacts are normally closed.

3. Secure the cable by tightening the two mounting screws.
4. Connect the opposite end of the cable assembly to the applicable terminals or receptacle on the robot controller.

A fault will be generated if any of the front panel controls are in the wrong position for automatic operation

This analog signal can be used to monitor motor speed. (0-10 VDC = 0-24,000 RPM)

For information about specific control assembly circuitry and connections, read the chart below and see the Wir- ing Diagrams on pages 56 and 57, and FIG. 11.

Graco 310554V — CAUTION diagram (page 19)
Fig. 7

Installing Cable Assemblies · ti0827A

Page 20 of the Graco 310554V user manual — Grounding the System
Page 20 · click to enlarge
Page 20

Verifying Ground Continuity

Verifying Ground Continuity

3. Fluid and air hoses: use only electrically conductive material and air hoses.

Verify ground continuity between:

4. Dispense gun: obtain grounding through the connection of the hose, or cable.
  • True earth ground and the control assembly ground terminal
5. Air compressor: follow the manufacturer’s recommendations.
  • The orbital dispenser and the robot
6. Object being sprayed: according to local code.

Adjusting the Orbital Dispenser

7. Fluid supply container: according to local code.

The PrecisionSwirl orbital dispenser is calibrated at the factory. No adjustment is required during initial setup.

Before applying power, read the reference information provided about controls and indicators to become famil- iar with the equipment.

Inspecting the Orbital Dispenser

Inspect the orbital dispenser cables, material, and air hoses daily for leakage and other visible damage.

Grounding the System

FIRE AND EXPLOSION HAZARD To reduce the risk of a fire, explosion, and serious injury, proper electrical grounding of every part of your system is essential. Read the warning section, FIRE AND EXPLOSION HAZARD, on page 5 and follow the grounding instructions below.

The following grounding instructions are minimum requirements for a basic dispensing system. Your sys- tem may include other equipment or objects which must be grounded. Check your local electrical code for detailed grounding instructions for your area and type of equipment. Your system must be connected to a true earth ground.

1. Pump: connect a ground wire and clamp to a true earth ground as shown in separate pump manual.
2. Orbital Dispenser: obtain grounding through the motor cable assembly.

Verifying Ground Continuity

Page 21 of the Graco 310554V user manual — PrecisionSwirl Module Operation
Page 21 · click to enlarge
Page 21

PrecisionSwirl Module Operation

Reading the PrecisionSwirl Control Assembly Controls and Indicators

Table 1 describes the controls on the PrecisionSwirl control assembly. See FIG. 12 for an illustration of the controls and indicators.

Table 1. Control Assembly Controls

Button/Switch What it does

MAIN ON/OFF Switch Controls power to the system.

  • In the MAIN ON (I) position, system power is turned on.
  • n the OFF (0) position, system power is turned off.

Control Select Switch AUTOMATIC / MANUAL

Switches the orbital dispenser to automatic or manual control.

  • In the AUTOMATIC position, the orbital dispenser is controlled from a remote source, such as a robot, via an interface cable.
  • In the MANUAL position, the orbital dispenser is controlled directly from the control assembly front panel.

RUN / ENABLE Button Pushing the RUN/ENABLE (black) button starts the orbital dispenser motor in manual mode or enables the motor to be started in automatic mode.

STOP Button Pushing the STOP (red) button removes power from the orbital dispenser.

MANUAL SPEED CONTROL Knob (potentiometer)

Regulates the motor speed of the orbital dispenser in the manual control mode.

  • Rotating the control knob clockwise increases motor speed.
  • Rotating the control knob counter–clockwise decreases motor speed.

Table 2 describes the indicators on the PrecisionSwirl control assembly. See FIG. 12 for an illustration of the controls and indicators.

Table 2. Control Assembly Indicators

Indicator Light is Meaning

POWER (white ON Power is on.

OFF Power is off.

RUN (green) ON PrecisionSwirl orbital dispenser is ready for operation, or is operating in manual control mode.

OFF PrecisionSwirl orbital dispenser is not ready for operation, or is not operating in manual control mode.

MOTOR FAULT (red) ON Motor is not rotating. Or, the motor is rotating below the mini- mum speed.

OFF Motor is functioning properly.

PrecisionSwirl Module Operation · Button/Switch

Page 22 of the Graco 310554V user manual — 8030A
Page 22 · click to enlarge
Page 22

0/7%2 -/4/2&!5,4 25.

-!).

25.%.!",%

#/.42/,3%,%#4

-!.5!,30%%$#/.42/,

!54/-!4)# -!.5!,

8030A

Setting Operation Modes

Material flow rate and “ON/OFF” flow are not con- trolled by the PrecisionSwirl orbital dispenser. These must be controlled by the other interfaces. Contact your Graco Distributor for assistance.

The PrecisionSwirl module has two operating states:

  • Automatic mode — enables the PrecisionSwirl orbital dispenser to be controlled by a remote signal source, such as a robot control. Motor speed can be controlled by a 0-10 VDC analog signal.

The PrecisionSwirl orbital dispenser is in an idle state until you press the RUN/ENABLE button on the control assembly. The only time the PrecisionSwirl orbital dis- penser can swirl material is when the RUN/ENABLE button is pressed in either Automatic or Manual mode. When the STOP button is pressed, the PrecisionSwirl orbital dispenser becomes idle and will not swirl mate- rial.

  • Manual mode — enables the PrecisionSwirl orbital dispenser to swirl when you press the RUN/ENABLE button on the control assembly. Swirling continues until the STOP button is pressed.

The procedures in this section configure the module for manual or automatic operation.

PrecisionSwirl Module Operation

Page 23 of the Graco 310554V user manual — Using Manual Mode
Page 23 · click to enlarge
Page 23

Using Automatic Mode

The system is now ready to dispense. Make sure dispensing will not endanger people or equipment before proceeding.

To put the PrecisionSwirl module into Automatic mode:

3. Press the RUN/ENABLE (black) button. Make sure the green RUN indicator, shown in F IG . 12, is lit at the control assembly.

You are about to place the system under robotic control. Make sure dispensing will not endanger people or equipment before proceeding.

The PrecisionSwirl orbital dispenser motor starts imme- diately.

1. Make sure the POWER indicator, shown in F IG . 12, is lit at the control assembly. If it is not, turn the MAIN power switch to the ON position, turning on power to the PrecisionSwirl control assembly circuitry.

To stop manual swirling and idle the module:

1. Press the STOP (red) button.
2. Set the CONTROL SELECT switch to AUTOMATIC.

The PrecisionSwirl orbital dispenser is now disabled and will stop swirling material.

3. Press the RUN/ENABLE (black) button. Make sure the green RUN indicator, shown in F IG . 12, is lit at the control assembly.
2. Make sure the green RUN indicator, shown in F IG . 12, is off at the control assembly.

The PrecisionSwirl orbital dispenser is now enabled. When it receives a 24 Volt RUN/ENABLE command from the robot, the PrecisionSwirl orbital dispenser motor starts and reaches full speed in about one sec- ond. The orbital dispenser motor stops when the 24 Volt RUN/ENABLE command is removed.

Analyzing Causes for a Motor Fault Alarm

Circuitry on the relay board monitors the motor speed to verify that the motor is functioning properly.

4. Leave the control assembly in this state during normal operation.

When the motor functions improperly, the circuitry on the relay board activates the motor fault alarm. The alarm turns on when:

To leave Automatic dispense mode and idle the module:

  • the motor speed has not risen within the +/-50% tolerance range within five seconds after startup.
1. Press the STOP (red) button.
2. Set the CONTROL SELECT switch to MANUAL.
  • the motor speed is outside the tolerance range for at least five seconds while operating.
3. Make sure the green RUN indicator, shown in F IG . 12, is off at the control assembly.

When a fault occurs, the motor fault light on the control panel illuminates, and the alarm relay activates sending the fault signal out via the automatic control cable. The alarm remains turned on until the fault condition is cor- rected or the run command is removed.

Using Manual Mode

1. Make sure the POWER indicator, in F IG . 12, is lit at the control assembly. If it is not, turn the MAIN power switch to the ON position, turning on power to the PrecisionSwirl control assembly circuitry.

A fault will also be generated if any of the front panel controls are not in the correct position for automatic operation (power switch, enable switch, manual/auto switch).

2. Set the CONTROL SELECT switch to MANUAL.
Show 4 more labels / short text on this page
PrecisionSwirl Module Operation · Entering Automatic Mode · Stop Manual Swirling · Leaving Automatic Mode
Page 24 of the Graco 310554V user manual — 0-10 VOLT
Page 24 · click to enlarge
Page 24

Adjusting Orbital Dispenser Motor Speed

Adjust the orbital dispenser motor speed in the manual or automatic control mode as described in the following para- graphs.

Manual Mode:

Automatic Mode:

Adjust motor speed by rotating the MANUAL SPEED CONTROL knob on the control box. See FIG. 12.

Use the motor speed chart (FIG. 13) to find the voltage setting required to achieve the desired motor speed. When the control signal voltage is increased, the motor speed increases. When the control signal voltage is decreased, the motor speed decreases.

Rotate the knob clockwise to increase speed and coun- terclockwise to decrease speed. Use the motor speed chart (FIG. 13) to find the manual control setting required to achieve the desired motor speed.

Exceeding the maximum analog speed control volt- age may result in damage to the motor controller.

0-10 VOLT

PrecisionSwirl Motor Speed Command

SPEED IN RPM x 1000

0 0 1 2 3 4 5 6 7 8 9

Analog speed signal from robot (Volts dc)

OR Manual control setting

PrecisionSwirl Module Operation

Page 25 of the Graco 310554V user manual — Troubleshooting
Page 25 · click to enlarge
Page 25

Troubleshooting

Some solutions require disassembling the dispense valve or orbital dispenser. Always relieve system pressure before performing these procedures.

Table 3 provides troubleshooting information. For other troubleshooting situations, call your Graco distributor.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pres- sure Relief Procedure (see manual 309043). To reduce the risk of serious injury whenever you are instructed to remove, change, check, clean, or han- dle the nozzle in any manner, always disconnect the motor control cable from the control assembly (see FIG. 8 on page 17), or place the control assembly in the MANUAL mode of operation using the CON- TROL SELECT switch. (See FIG. 12 on page 22.)

Table 3. Troubleshooting

No material being dispensed Clogged nozzle Change nozzle.

No material or pressure Check fluid delivery system.

Broken or clogged dispense tube Rebuild the orbital dispenser.

Fault in dispense valve Refer to Dispense Valve manuals 308876 or 309376.

Material dispensing but not swirling (Motor fault light is on)

Motor not operating Check wiring connections and cable.

Tube bearing defective; replace tube bearing.

Motor defective; replace motor.

Check for fluid leak.

Control assembly failure Check analog voltage control setting and enable signal.

Check RPM setting.

Check power and fuses.

Check wiring.

Orbiter bearing failure Replace bearing.

Material dispensing but not swirling

Material accumulating on nozzle Clean nozzle.

(Motor fault light is off)

Motor is rotating but poor swirl pat- tern or change in bead size

Flow rate has changed Check flow rate.

Motor speed has changed Check analog speed signal.

Material viscosity has changed Check material parameters.

Partially clogged nozzle Clean nozzle.

Troubleshooting · Problem Cause Solution

Page 26 of the Graco 310554V user manual — Lamp Button and Switch Replacement
Page 26 · click to enlarge
Page 26

Control Assembly Service

Servicing the Control Assembly

2. Refer to F IG . 21 and F IG . 22 for lead wire identification.

This part of the manual provides information about the following control assembly components:

3. Apply system power at the main circuit breaker.
4. Move the MAIN power switch to the ON position, applying power to the control assembly.
  • Indicator Lamp Button and Select Switch (page 26)
  • Light Bulb (page 26)
  • MAIN Power Switch (page 27)
  • Potentiometer (page 28)
5. Verify that the replaced fixture operates correctly.
6. Return the orbital dispenser and control assembly to normal operating condition.

Refer to the Parts information on pages 34, 36, and 38 while servicing the control assembly.

Light Bulb Removal

Lamp Button and Switch Removal

Remove the light bulb as follows:

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

1. Shut off system power at the main circuit breaker.
1. Shut off system power at the main circuit breaker.
2. At the control assembly, move the MAIN power switch to the OFF position.
2. At the control assembly, move the MAIN power switch to the OFF position.
3. Unscrew and remove the indicator light lens.
3. Unlock and open the hinged cover of the control assembly enclosure.
4. Gently press and rotate the bulb counter-clockwise, 1/4 in. of a turn, unlocking the bulb from its socket. Remove the bulb from the socket.
4. Disconnect the lead wires from the fixture terminals. Refer to F IG . 21 and F IG . 22 for lead wire identification. If necessary, label the wires to facilitate reassembly after the fixture is replaced.

Light Bulb Replacement

Replace the light bulb as follows:

1. Insert the light bulb in the socket.
5. Loosen two screws which clamp the fixture to the cover. Rotate the fixture counter–clockwise relative to the lens cover or switch operator. Separate the two parts of the fixture and remove them from the cover.
2. Gently press and rotate the bulb clockwise, 1/4 in. of a turn to lock the bulb in its socket.
3. Replace the lens.

Lamp Button and Switch Replacement

4. Apply system power at the main circuit breaker.
5. Move the MAIN power switch to the ON position, applying power to the control assembly.
1. Reverse the disassembly procedures 3-5 in the previous section.
6. Verify that the light bulb operates correctly.

Control Assembly Service

Page 27 of the Graco 310554V user manual — MAIN Power Switch Removal
Page 27 · click to enlarge
Page 27
7. Return the control assembly to normal operating condition.
6. Remove two flat head screws from the yellow mounting plate, which fastens the switch to the hinged cover. Remove the switch.

MAIN Power Switch Removal

MAIN Power Switch Replacement

Remove the MAIN power switch as follows:

Graco 310554V — MAIN Power Switch Removal diagram (page 27)
Fig. 8 · MAIN Power Switch Removal

Replace the MAIN power switch as follows:

1. Assemble the switch assembly to the yellow mounting plate with two flat head screws.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly

2. Assemble the red rotor, which is keyed, onto the yellow mounting plate with one flat head screw. See Fig. 15.
1. Shut off system power at the main circuit breaker.
3. Turn the rotor to point down to ensure that the switch is in the OFF position.
2. At the control assembly, move the MAIN power switch to the OFF position. See F IG . 14.
4. Reconnect the lead wires to the terminals on the switch. Refer to Fig. 18 to make sure that the connections are correct.
3. Unlock and open the hinged cover of the control assembly.
5. Close and lock the hinged cover on the control assembly.
4. Disconnect the lead wires from the four terminals on the MAIN power switch. Refer to F IG . 21 and F IG . 22 for lead wire identification. If necessary, label the wires to facilitate reassembly after the switch is replaced.
6. Apply system power at the main circuit breaker.
7. Move the MAIN power switch to the ON position applying power to the control assembly.
5. Remove one flat head screw that secures the red rotor to the switch assembly. Lift the rotor from the switch.
8. Verify that the switch operates correctly.
Graco 310554V — MAIN Power Switch Removal diagram (page 27)
Fig. 9 · MAIN Power Switch Removal

Control Assembly Service

Page 28 of the Graco 310554V user manual — 8040A
Page 28 · click to enlarge
Page 28

Potentiometer Removal

Potentiometer Replacement

Remove the potentiometer as follows:

Replace the potentiometer as follows:

1. Insert the potentiometer through its hole from the back of the enclosure cover and rotate it so that terminals 1 and 3 are oriented at approximately 4:30 when viewed from the back. Refer to F IG . 16. Assemble the lockwasher and nut onto the shaft and secure the potentiometer to the cover.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

2. At the front of the cover, turn the potentiometer shaft counter–clockwise to its stop.
3. Pre–set the vernier dial to 0.00 and place it over the potentiometer shaft, with its key tab inserted into the blind hole in the cover front surface. Tighten the dial setscrew (not shown) against the shaft.
1. Shut off system power at the main circuit breaker.
2. At the control assembly, move the MAIN power switch to the OFF position.
4. Verify that the potentiometer is turned fully counterclockwise when the vernier dial indicates 0.00. Loosen the setscrew and reposition the shaft and dial if necessary, then retighten the setscrew.
3. Unlock and open the hinged cover of the control assembly.
4. Pull lead wires to remove from potentiometer.
5. Loosen setscrew (not shown) in the vernier dial knob and remove dial assembly from the potentiometer shaft.
5. Connect wire leads to potentiometer.
6. Close and lock the cover on the control assembly.
7. Apply system power at the main circuit breaker.
6. Remove the hex nut and lockwasher from potentiometer shaft, and remove the potentiometer.
8. Move the MAIN power switch to the ON position, applying power to the control assembly.
9. In the MANUAL control mode, verify that the potentiometer operates correctly.
10. Return the orbital dispenser and control assembly to normal operating condition.

Terminals 1 and 3

8040A

2172 8034B

Show 8 more labels / short text on this page
Control Assembly Service · Vernier dial · Cover · Potentiometer · 2172 2132 2181 · Nut · Locating Tab · Terminal 2 2181
Page 29 of the Graco 310554V user manual — Panel Assembly Service
Page 29 · click to enlarge
Page 29

Panel Assembly Service

This part of the manual provides information about the following panel assembly components:

  • Swirl Control Board (page 30)
  • RFI Filter (page 31)
  • Relay (page 32)
  • Fuse (page 33)
Graco 310554V — Panel Assembly Service diagram (page 29)
Fig. 10 · Panel Assembly Service

*

Show 4 more labels / short text on this page
Panel Assembly Service · Relay Board · Motor Control · RFI Filter
Page 30 of the Graco 310554V user manual — Swirl Control Board Removal
Page 30 · click to enlarge
Page 30

Swirl Control Board Removal

Swirl Control Board Replacement

Remove the relay board as follows:

Replace the relay board as follows:

1. Snap the swirl control board onto the din rail.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

2. Plug the connectors into the swirl control board. Refer to F IG . 17 for lead wire identification.
3. Close and lock the hinged cover on the control assembly.
4. Apply system power at the main circuit breaker.
1. Shut off system power at the main circuit breaker.
5. Move the MAIN power switch to the ON position, applying power to the control assembly.
2. At the control assembly, move the MAIN power switch to the OFF position.
6. Verify that the relay board operates correctly.
3. Unlock and open the hinged cover of the control assembly.
7. Return the control assembly to normal operating condition.
4. Unplug the connectors from the swirl control board.
5. Pry the plastic cups off the board with a screwdriver to release the board from the din rail.

Panel Assembly Service

Page 31 of the Graco 310554V user manual — RFI Filter Removal
Page 31 · click to enlarge
Page 31

RFI Filter Removal

RFI Filter Replacement

Remove the RFI Filter as follows:

Replace the RFI filter as follows:

1. Install the RFI filter using the two screws and lockwashers to secure the component on the panel assembly. See F IG . 17.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

2. Connect the wires to the correct terminal block on the control board. Refer to F IG . 17 for lead wire identification.
3. Close and lock the hinged cover on the control assembly.
1. Shut off system power at the main circuit breaker.
4. Apply system power at the main circuit breaker.
2. At the control assembly, move the MAIN power switch to the OFF position.
5. Move the MAIN power switch to the ON position, applying power to the control assembly.
3. Unlock and open the hinged cover of the control assembly.
6. Verify that the RFI filter operates correctly.
7. Return the control assembly to normal operating condition.
4. Disconnect the wires from the terminal blocks on the control board. If necessary, label the wires to facilitate reassembly after the control board is replaced.
5. Remove the two screws and lockwashers from the RFI filter on the panel assembly. See F IG . 17.
6. Remove the RFI filter.

Panel Assembly Service

Page 32 of the Graco 310554V user manual — Relay Removal
Page 32 · click to enlarge
Page 32

Relay Removal

Relay Replacement

Remove the relay as follows:

Replace the relay as follows:

Graco 310554V — Relay Removal diagram (page 32)
Fig. 11 · Relay Removal

Relays are always P/N 15A797, 24 VDC. If the robot run command signal for automatic control mode is 24 VDC, then relay is also P/N 15A797.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

1. Match pattern on bottom side of relay to base. Plug relay into base. F IG . 18.
2. Close and lock the hinged cover on the control assembly.
1. Shut off system power at the main circuit breaker.
3. Apply system power at the main circuit breaker.
2. At the control assembly, move the MAIN power switch to the OFF position.
4. Move the MAIN power switch to the ON position, applying power to the control assembly.
3. Unlock and open the hinged cover of the control assembly.
5. Verify that the relay operates correctly.
6. Return the control assembly to normal operating condition.
4. With force, carefully pull the top of the relay to unplug the relay from the base. See F IG . 18.
Graco 310554V — Relay Removal diagram (page 32)
Fig. 12 · Relay Removal

*

Panel Assembly Service

Page 33 of the Graco 310554V user manual — Fuse Replacement
Page 33 · click to enlarge
Page 33

Fuse Removal

6. Carefully remove the fuse (24) from the fuse holder.

Remove the fuse as follows:

Fuse Replacement

Graco 310554V — Fuse Replacement diagram (page 33)
Fig. 13 · Fuse Replacement

Replace the fuse as follows:

Check the new fuse (24) to ensure that it matches the Amp rating of the failed fuse.

ELECTROCUTION HAZARD Installing and servicing this equipment requires access to parts which could cause an electric shock or other serious injury. Have only qualified electricians access the control assembly.

1. Press both ends of the new fuse evenly into place in the fuse holder. See F IG . 19.
2. Close and lock the fuse holder into place.
1. Shut off system power at the main circuit breaker.
3. Close and lock the hinged cover on the control assembly.
2. At the control assembly, move the MAIN power switch to the OFF position.
4. Apply system power at the main circuit breaker.
3. Unlock and open the hinged cover of the control assembly.
5. Move the MAIN power switch to the ON position, applying power to the control assembly.
4. Lift to unlock the top of the fuse holder (10), which is hinged at the bottom, from its clamp. See F IG . 19.
6. Verify that the fuse operates correctly.
7. Return the orbital dispenser and control assembly to normal operating condition.
5. Open the fuse holder fully. Locate the failed fuse inside. Refer to F IG . 21 and F IG . 22 for fuse identification.
Graco 310554V — Fuse Replacement diagram (page 33)
Fig. 14 · Fuse Replacement

*

Lift the top of the fuse holder to unlock

Fuse location (2 places)

Panel Assembly Service

Page 34 of the Graco 310554V user manual — Part No. 918616, PrecisionSwirl Control Assembly
Page 34 · click to enlarge
Page 34

Control Assembly Parts

Part No. 918616, PrecisionSwirl Control Assembly

Ref. No. Part No. Description Qty. 1 241487 CABINET, PrecisionSwirl 1 2 194896 LABEL, front panel, 1 3 241580 PANEL, ASSY, control 1 4 241600 CONNECTOR, motor 1 5 617771 GASKET, flange, electrical connec- tor, #14

6 241599 CONNECTOR, robot 1 8 C19949 SCREW, SHC, #4-40 x 0.25 4 9 115237 SWITCH, power, rotary 1 13 617777 LIGHT base, direct supply 2 14 617778 LENS, light, white, 7/8 1 15 617779 LENS, light, green, 7/8 1 16 617780 LAMP, incandescent, 24V 2 17 617781 SWITCH BASE, 1-NO, 1-NC 2 18 617782 ACTUATOR, switch, 2–PB, rect 1 19 617783 ACTUATOR, switch, 2 position 1 20 617775 POTENTIOMETER, 10 turn, 10K ohm, 0.5W

21 617776 DIAL, vernier, 15 turn 1 22† 113285 TERMINAL, ring, #10 2 23† 100718 WASHER 2 24† 617774 NUT, hex, #10-32, brass 4 31 194897 LABEL, cable connector 1 32▲† 617472 LABEL, danger, electric shock 1 34† C19738 SCREW, drive, round head 4 35 C78216 CLAMP, ty–rap 10 36 C78321 TIE, cable, 3.62 long 18 42 100731 WASHER 4 43 100133 WASHER, lock 4 44† 100307 NUT, full, hex 4 45 195899 DUCT, wire, 10 in. 1 47† 114887 KEY, latch, door 1 51 115217 SCREW, female, kit 1 52 194984 COVER, wire, duct, 10 in. 1 53 115434 LENS, light, red, 7/8 1

† These parts are not shown on the parts drawing.

▲Replacement Danger and Warning labels, tags, and

cards are available at no cost.

Control Assembly Parts

Page 35 of the Graco 310554V user manual — 8027A
Page 35 · click to enlarge
Page 35

Part No. 918616, PrecisionSwirl Control Assembly

POWER MOTOR FAULT RUN

MAIN RUN / ENABLE

CONTROL SELECT

MANUAL SPEED CONTROL

AUTOMATIC MANUAL

8037B

8, 4, 5 6, 51 46

0/7%2 3500,9 !54/-!4)##/.42/,

8027A

Show 5 more labels / short text on this page
Control Assembly Parts · 20, 21 · -/4/2 · #!",% · #!",%
Page 36 of the Graco 310554V user manual — Part No. 918616, PrecisionSwirl Control Assembly
Page 36 · click to enlarge
Page 36

Part No. 918616, PrecisionSwirl Control Assembly

13, 53, 16 13, 15, 16

'.$

36 45, 48 52 17, 19 35

Show 20 more labels / short text on this page
Control Assembly Parts · 13, 14, 16 · 17, 18 · · · · · · · · · · · · · · · · ·
Page 37 of the Graco 310554V user manual — Part No. 918616, PrecisionSwirl Control Assembly
Page 37 · click to enlarge
Page 37

Part No. 918616, PrecisionSwirl Control Assembly

'.$

'.$

'.$

'.$

,. 0%

6!# 0( (:

Show 103 more labels / short text on this page
Control Assembly Parts · 42, 43, 16 · · · * · * · * · * · * · * · #2 #2 #2 · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · , · ·
Page 38 of the Graco 310554V user manual — Part No. 241580, PrecisionSwirl Panel Assembly
Page 38 · click to enlarge
Page 38

Part No. 241580, PrecisionSwirl Panel Assembly

Ref. No. Part No. Description Qty.

Ref. No. Part No. Description Qty. 1 194693 PLATE 1 2 115215 POWER SUPPLY 1 3 194895 RAIL, mount 2 5 244355 BOARD, swirl control 1 7 102410 SCREW, cap, socket head 2 8 100272 WASHER, lock, internal tooth 2 9 112443 BLOCK, terminal, ground 8 10 514556 HOLDER, fuse 2 11 115234 COVER, terminal 1 12 112446 BLOCK, clamp, end 7 13 112442 BLOCK, terminal 23

14 103833 SCREW, machine, bdgn 12 15 115212 FILTER, RFI 1 16 194894 DUCT, wire 1 21 194976 LABEL, wiring 1 22 100718 WASHER 12 23† 115130 JUMPER PIN 1 24† 115216 FUSE, 2 AMP High Interrupting 2 26 194985 COVER, wire, duct, 14 in. 1

† These parts are not shown on the parts drawing.

Graco 310554V — Part No. 241580, PrecisionSwirl Panel Assembly diagram (page 38)
Fig. 15 · Part No. 241580, PrecisionSwirl Panel Assembly

*

2 11 10, 26 9

Control Assembly Parts · 7, 8

Page 39 of the Graco 310554V user manual — Control Assembly Parts
Page 39 · click to enlarge
Page 39

Control Assembly Parts

Page 40 of the Graco 310554V user manual — CONNECTION DIAGRAM 8031A
Page 40 · click to enlarge
Page 40

Accessory Parts

Motor Control Cable Assemblies

Table 5. Motor Control Cables

The motor control cables that are provided with the module are OLFLEX® brand cables. The 55 ft (16.8) motor cable (617870) can be used alone.

Part Number Length Description

617870 55 ft (16.8 m) Motor cable assembly

P/N 617870 SOCKET PIN

FUNCTION V+ SENSOR 1 SENSOR 2 SENSOR 3 V- SHIELD TIED TO CONNECTOR SHELL SHIELD TIED TO CONNECTOR SHELL

A B C D E

A B C D E

WHITE BROWN GREEN YELLOW

GREY

H J K L M

H J K L M

RED 1 RED 2 RED 3 GREEN/YELLOW

MOTOR PH. A MOTOR PH. B MOTOR PH. C GROUND

CONNECTION DIAGRAM 8031A

Accessory Parts

Page 41 of the Graco 310554V user manual — GREEN/YELLOW
Page 41 · click to enlarge
Page 41

Torsional Motor Control Cable Assemblies

Table 6. Motor Control Cables

Part Number Length Description

For robot applications that have a lot of torsional motion to the cable in addition to bending. These cables are made from Olflex 900 series robot cable that are designed to handle more torsional loads. The cables must be used in conjunction with the 55 ft motor cable.

233125 6 ft (1.8 m) Motor cable assembly

233124 9 ft (2.7 m) Motor cable assembly

233123 15 ft (4.6 m) Motor cable assembly

P/N 233123, 233124, 233125 SOCKET PIN

FUNCTION V+ SENSOR 1 SENSOR 2 SENSOR 3 V-

A B C D E

A B C D E

WHITE BROWN GREEN YELLOW

GREY

H J K L M

H J K L M

MOTOR PH. A MOTOR PH. B MOTOR PH. C GROUND

GREEN/YELLOW

CONNECTION DIAGRAM

Accessory Parts

Page 42 of the Graco 310554V user manual — ORANGE BLACK/RED
Page 42 · click to enlarge
Page 42

Robot Interface Cable Assembly

The length of robot interface cable assembly 617829 is 40 ft (12.2 m). FIG. 26 shows the 9-pin cable and identi- fies the cable interface signals.

P/N 617829

REFERENCE FUNCTION

SHIELD

RED GREEN BLACK GREEN/BLACK

1 2 3 4 5 6 7 8 9

0-10 VDC ANALOG SPEED CONTROL

0-10 VDC ACTUAL SPEED SIGNAL DC COMMON NOT USED RUN COMMAN SIGNAL ALARM RELAY IN ALARM RELAY OUT NOT USED RUN COMMAND NEUT/COM

ORANGE BLACK/RED

BLUE WHITE/BLACK

WHITE

CONNECTION DIAGRAM

Dispenser Valve Adapter Fittings

Ref. No. Part No. Description Qty. 1 197504 Straight flange adapter, EnDure 1 2 197842 45 degree nosepiece 1 3 198323 Alternative orbiter nut 1 4 198324 Fitting, nosepiece to orbiter 1

45 degree orbiter mount uses reference numbers 2-4.

Accessory Parts

Page 43 of the Graco 310554V user manual — Wiring Diagrams
Page 43 · click to enlarge
Page 43

Wiring Diagrams

Motor Controller Wiring, Lines 200-238

6!# (:

,.

,.

'.$

,.

'.$

,.

2/"/4 !.!,/'

!54/ #2

-!.5!, .#

25.%.!",%

Show 116 more labels / short text on this page
Wiring Diagrams · · · · · · , · · · · · · , · · · · · , · &),4%2 · · · · · · · , · · · · · · · · · · · · 0/7%23500,9 · · 637)2,* · · · · #2 · · · · · · · + · · · · · · · #2 · · · 6$# · · #2 · #2 · · · · · · · #2 · · · · #/- · · · · · · · · 34/0 · ' · · · #2 · · · · · · #2 · · · · #2 · · · #2 · · · · · · · · #2 · · · · · #2 · #2 · ·
Page 44 of the Graco 310554V user manual — Motor Controller Wiring, Lines 250-288
Page 44 · click to enlarge
Page 44

Motor Controller Wiring, Lines 250-288

-/4 *

'.$ -0 -

25..%5#/-

%84%2.!, !54/-!4)#

#/.42/,

'2!#/37)2,#/.42/,

).054

25.6

!,!2-2%,!9).

Show 110 more labels / short text on this page
Wiring Diagrams · · · · · · · * · · · * · · · -0 * ! · · * · · -0 , · # · · * · · -0 + · " · · * · · · -0 ! · · * · · -0 " · 3 3 · · -0 # · · * · · -0 $ · 3 · · * · -0 % · · * · · · * · · · · · * · · * · · · · * · · · * · · · · * · * · · / 6$# /54054 · · · * · · * · · · · * · $##/- · · · * · · * · · · / 6$# · · · · · · !,!2-2%,!9/54 · · · · · · · · · · · · · · · ·
Page 45 of the Graco 310554V user manual — Technical Data
Page 45 · click to enlarge
Page 45

Technical Data

Control Assembly Input power 100 - 240 Vac, 50/60Hz, 1 PH Output power Proprietary PWM voltage to the motor, less than 24V Automatic control analog input 0-10 VDC for 6600-24,000 RPM Speed signal output 0-10 VDC for 0-24,000 RPM Auto control relay contact rating 3 Amps at 30 VDC Weight 23.5 lbs (10.7 kg)

Orbital Dispenser Input power Proprietary PWM voltage to the motor, less than 24V Motor torque 1.5 oz–in. Maximum motor speed 24,000 RPM Maximum operating pressure 3500 psi (241 bar, 24.1 MPa) Fluid inlet 3/4-16 37° JIC female swivel Nozzle attachment #10-32 proprietary connection Wetted components Stainless steel, nickel alloy, brazing alloy, epoxy, EPDM

rubber Noise levels Sound pressure level - 67 dBa Weight 1.6 lbs (0.7 kg)

PrecisionSwirl™ is a trademark of Graco, Inc.

PARKER O LUBE™ is a trademark of Parker Hannifin Corp.

Loctite® is a registered trademark of the Loctite Corporation.

Technical Data

Page 46 of the Graco 310554V user manual — GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Page 46 · click to enlarge
Page 46

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English. MM 310554

Graco HeadquartersMinneapolis International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2001, Graco Inc. is registered to ISO 9001

www.graco.com Revised 11/2009

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
No material being dispensedClogged nozzleChange nozzle. p.25
No material being dispensedNo material or pressureCheck fluid delivery system. p.25
No material being dispensedBroken or clogged dispense tubeRebuild the orbital dispenser. p.25
No material being dispensedFault in dispense valveRefer to Dispense Valve manuals 308876 or 309376. p.25
Material dispensing but not swirling (Motor fault light is on)Motor not operatingCheck wiring connections and cable. p.25
Material dispensing but not swirling (Motor fault light is on)Tube bearing defective; replace tube bearing. p.25
Material dispensing but not swirling (Motor fault light is on)Motor defective; replace motor. p.25
Material dispensing but not swirling (Motor fault light is on)Check for fluid leak. p.25
Material dispensing but not swirling (Motor fault light is on)Control assembly failureCheck analog voltage control setting and enable signal. p.25
Material dispensing but not swirling (Motor fault light is on)Check RPM setting. p.25
Material dispensing but not swirling (Motor fault light is on)Check power and fuses. p.25
Material dispensing but not swirling (Motor fault light is on)Check wiring. p.25
Material dispensing but not swirling (Motor fault light is on)Orbiter bearing failureReplace bearing. p.25
Material dispensing but not swirling (Motor fault light is off)Material accumulating on nozzleClean nozzle. p.25
Motor is rotating but poor swirl pat- tern or change in bead sizeFlow rate has changedCheck flow rate. p.25
Motor is rotating but poor swirl pat- tern or change in bead sizeMotor speed has changedCheck analog speed signal. p.25
Motor is rotating but poor swirl pat- tern or change in bead sizeMaterial viscosity has changedCheck material parameters. p.25
Motor is rotating but poor swirl pat- tern or change in bead sizePartially clogged nozzleClean nozzle. p.25

Ask about the Graco 310554V

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Graco 310554V

Be the first to ask — other owners or our team will answer.

Original document

Graco 310554V manual PDF

46 pages·1.9 MB·Water Dispenser·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…