Instruction/ maintenance manual of the product 260000 Graco
Go to page of 16
311304H Instructions - Parts List GTP10 Pump For pumping gasoline, diesel fu el, and kerosene. Do not use to pump other fluids including water. Models 260000 through 260017, 260019, 260024, 260580, an.
Models 2 311304H Models Part No. Hose Nozzle 12 VDC, 10 gpm (38 lpm), 12.5 amps 260000 260069 - 12 ft (3.66 m) grounded 260079 - manual, leaded/die sel 260001 260069 - 12 ft (3.66 m) grounded 260082 - automatic, regula r/diesel 260002 260069 - 12 ft (3.
Models 311304H 3.
Warnings 4 311304H Warnings The following general warn ings are for the setup, use, ground ing, maintenance, and repair of this equipme nt. Addi- tional, more specific warnings may be found th ro ughout the body of this manual where applicable. Symbols appea r- ing in the body of the manual re fer to these general warnin gs.
Warnings 311304H 5 EQUIPMENT MISUSE HAZARD Misuse can cause de ath or serious injury. • Do not operate the unit when fatigued or under the influen ce of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
Installation 6 311304H Installation When unpacking pump, check for shipp ing damage. Report any shipping damage to delivering carrier imme- diately. Mounting Pump 1. Apply PTFE thread tape (provided with the pump) to large thread of bu ng adapter (9) (2 in.
Installation 311304H 7 3. Cut the suction tube so that it is 2 in. (55 mm) from the bottom of the tank when installed in the tank. 4. Insert ga sket (7f) into union nut (1k). If using Grac o supplied PVC suction tube it is not necess ary to apply thread tape before assembly, just scre w into pump inlet (1j).
Installation 8 311304H Electrical Installation 12 VDC and 24 VDC To install wiring for a ne gative grou nd system : 1. Ensure pump switch is OFF. 2. To remove electrical cover (2a) , remove four bolts (2c). 3. Strip 3 in. (76 mm ) of outside insu lation from power cable (6c) from e nd opposite of fuse.
Operation 311304H 9 Priming Pump All pump models should prime with in 5 seconds after pump is turned on up to a height of 36 in. (9 1 mm). Pumps installed at height up to 5 ft. (1.52 m) may have difficulty priming. Follow pr ocedure below to initiate prime.
Troubleshooting 10 311304H Troubleshooting Problem Cause Solution Motor runs but pump will not prime. Motor rotation wrong. (12 VDC and 24 VDC units only.) Check wiring in structions for possible problems. Missing relief valve o-ri ng seal (4c/7a). Remove gear cover (1b) inspect seal (4c/7a), replace if missing or damaged.
Troubleshooti ng 311304H 11 Motor stalls when nozzle is clos ed. Bypass relief valve (4a) stuck. Inspect relief valve, making sure poppet is free. Replace if damaged. Low supply voltage. Check supply voltage. Gears (1c/10a) dam aged and binding. Inspect gears.
Parts Drawing 12 311304H Parts Drawing 3a 3c 3d/7e 1a 8e 8b 8f 8g 1h 1e/7b/10c 1f/7c/10b 2e 2f 3b 1b 1c/ 10a 1d 4b 4a 2h 2i 8c 8a 8d 4c/ 9 7f 1k 1g/7d 2g 2c 2b 2d 5c 5a 2a 2c 6b 6c 6a Models 260000 th.
Parts Li st 311304H 13 Parts List Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 260028, 115 VAC Ref.
Parts List (continued) 14 311304H Parts List (continued) Models 260000 through 260017, 260019, and 260024, 12 VDC Models 260020 and 260021, 24 VDC Models 260022 and 260023, 230 VAC Models 260025 through 260028, 115 VAC Replacement Danger an d Warning labels, tags, and cards are available at no cost.
Technical Data 311304H 15 Technical Data Valox ® is a register ed trademar k of the General Elect ric Company Performance Chart Working pressure 10 psi (0.07 MPa, 0.7 bar) Inlet size 1 in. npt Outlet siz e 3/4 in. npt Weight 20 lb (9 kg) Power cable 18 ft (5.
All written and visual data contained in this document reflects the latest product info r mation available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311304 Graco Headquarters: Minne apolis International Offices: Belgium, China, Japan, Korea GRACO INC.
An important point after buying a device Graco 260000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco 260000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco 260000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco 260000 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco 260000 will certainly help you make a decision on the purchase.
If you already are a holder of Graco 260000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco 260000.
However, one of the most important roles played by the user manual is to help in solving problems with Graco 260000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco 260000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
