Instruction/ maintenance manual of the product 24B798 Graco
Go to page of 18
Kit Instr uctions/P ar ts DataT rak ® Kits 313840G EN For pro viding pump diagnost ics and material usage inf o rmation f or diaphragm pumps. Con ver sion Kits - DataT rak with Pulse Count and Runawa.
Contents 2 313840G Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 DataT rak Kit s . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DataTrak Kits 313840G 3 DataT rak Kits Con versio n Kits Use to add data monitoring capabilities to an e xisting pump . * Kit includes repla cement air valv e compatib le with solenoid.
Installation 4 313840G Installation Prepare to Install 1. Relie ve the pressure. F ollow instructions in your Operat ion manual. 2. Disconnect the a ir line to the pump . Install the Kit 1. Mount t he brack et to the wall. Use approximately 3/8 in. bo lts or screws .
Installation 313840G 5 6. Use the scre w provided to attach the r eed switch just behind the air inlet. Remov e the muffler , if needed, for easier access. Rotate the air inlet fitt ing as needed so th e wrench flat clears the reed s witch. 7. Connect the Da taT rak cab le to the 5-pin connector on the reed s witch.
DataTrak Controls and Indicators 6 313840G DataT rak Contr ols and Indicator s Key AA Runaw ay Lim it, in cycles per minute (user settable; 00=OFF) AB Displacement (user settable) A C Flow Rate Units .
DataTrak Operation 313840G 7 DataT rak Operation NO TE: The display (AE) will turn off after 1 minute to sav e batter y lif e. Press any ke y to wake up the displa y . NO TE: DataT rak is f actor y se t to 685 cc/cy cle. This set- ting is accur ate f or pumping water at a medium speed on a Husky 1050 pump (a pproxima tely 20 gpm).
DataTrak Operation 8 313840G NO TE: If the DataT rak does not r eset, use a scr ewdriver to push the sole noid release butt on on the side of the air va lve . 5. If the so lenoid doesn’t actuate: a. Close the master air v alve to stop the pump. The displa y will show the Ser vice Component 1 screen.
DataTrak Operation 313840G 9 Calibration Pr ocedure 1. Press and hold f or 5 seconds until Setup me nu appears . 2. Press once. Change flo w rate units to cycles/min. 3. Retur n to Run Screen. Press a nd hold for three seconds to reset batch to talizer .
DataTrak Operation 10 313840G T able 1: Diagnostic Codes Symbol Code Code Name Diagnosis Cause Runa wa y Pump running f aster than set runawa y limit. Increased air pressure. Increased flu id output. Exhausted fluid supply . E-3 Low Battery Batter y v oltage too low t o stop r unawa y .
DataTrak Operation 313840G 11 Replace DataT rak Battery or Fuse Replace Battery 1. Unscrew cable from the reed s witch asse mbly . See Fig. 2. 2. Remove DataT rak module from bracket. See Fig. 3. T ak e module to a non-hazardous locati on. 3. Remo ve two scre ws on bac k of module to access battery .
DataTrak Operation 12 313840G Replace Fuse 1. Remove the screw , metal s trap , and pl astic holder . 2. Pull the fuse awa y from the bo ard. 3. Replace with a new fuse.
DataTrak Operation 313840G 13.
Parts 14 313840G Pa r t s Con version Kits, Cyc le Count and Runawa y Protection Husky 1050 - 24B777 (Aluminu m), 24B784 (P olypro pylene), and 24B793 ( Conductive P olypr opylene) Husky 3300 - 24K861.
Parts 313840G 15 ▲ Replacement W a rning labels, signs , tags, and cards are a vailab le at no cost. ----- Not sold separately . Ref. No. Part No. Descr iption Qty 1 ----- D A T A TRAK module (see p.
Parts 16 313840G Con version Kits, Cyc le Count Only Husky 1050 and Husky 3300 - 24B794 (Aluminum) and 24 B795 (P olypr opylene and Conductive P olypropylene) ▲ Replacement W a rning labels, signs , tags, and car ds are av ailable at no cost. 1 2 3 5a 5b ti14224a Ref.
Parts 313840G 17 Replacement Kits Solenoid/Reed Switch Reed Switch Husky 1050 Husky 3300 Air V alve Material Incl udes 24B771 24K863 Plastic Reed s witch and solenoid (4a), brac ket ( 4c), and fa sten.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions.This m anual contains English.
An important point after buying a device Graco 24B798 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Graco 24B798 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Graco 24B798 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Graco 24B798 you will learn all the available features of the product, as well as information on its operation. The information that you get Graco 24B798 will certainly help you make a decision on the purchase.
If you already are a holder of Graco 24B798, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Graco 24B798.
However, one of the most important roles played by the user manual is to help in solving problems with Graco 24B798. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Graco 24B798 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
