Instruction/ maintenance manual of the product 600MP Gilson
Go to page of 28
GILS J J N MIXERS MORTAR-PLASTER MIXER MODEL: 600MP OPERATOR’S GUIDE & PARTS MANUAL GILS J J N MIXERS BY 4343 Easton Road · St. Joseph, MO 64503 816-233-4840 · 800-253-3676 Fax 816-233-4624 · 888-253-3676 E-Mail: cleform@ccp.com Web Address: www.
1 INTRODUCTION This operator’s manual has been prepared to provide the information you need to correctly operated and maintain your mixer. For maximum satisfaction, carefully read and follow the instructions in this manual. Should you need repair parts or service, refer to the parts breakdown on pages 14 through 25.
2 TABLE OF CONTENTS 1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. ASSEMBLY AND PREOPERATIONAL CHECKS . . . . . . . 4 3. CONTROLS AND OPERATION Clutch Control Lever . . . . . . . . . . . . . . . . . . . . . . . . .
3 1 – SAFETY PRECAUTIONS THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND PRACTICE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS.
4 Never charge or fill the unit prior to starting the mixing blades as an overload encountered in starting a loaded unit could damage the engine/motor or drive components. Connect safety chains as instructed when towing the mixer. Connect only to correct hitch or coupler.
5 3 – CONTROLS AND OPERATIONS 1. The mixing paddles feature adjustable rubber wipers and steel backing plates. Paddles are factory preset for appropriate drum wrap clearance.
6 TOW POLE ASSEMBLY The tow pole assembly is located on the front of the mixer and is used for transport only. For transport, pull the tow pole assembly out, line up the hold and insert the L-shaped pin through holes. When operating the mixer, pull the L-shaped pin out of the hole and push tow pole assembly all the way in.
7 4 – MIXER TRANSPORT 1. Secure drum by engaging drum lock. 2. Secure all moveable parts, including the rear housing. 3. Secure tow pole coupler to vehicle and attach safety chains and hooks. (See FIGURE 2 , Safety Chains). A. Pintle type couplers require the appropriate tow vehicle coupler retainer.
8 LOADING THE MIXER When the mixing blades are rotating, pour the required amount of water into the drum , then add cement, sand and lime. The desired mixing speed is 33 RPM DISCHARGING THE MIXER Allow the entire mixture to mix for one (1) full minute.
9 TROUBLE SHOOTING GUIDE FOR MP MIXERS. ENGINE WON’T START: 1. Check for sufficient fuel. 2. Check oil level (some engines have an oil alert, preventing the engine from starting when oil level is low) 3. Was engine choked when starting? 4. Is engine flooded? 5.
10 6 – OPERATING GUIDELINES MASONRY CONSTRUCTION GUIDELINES The strength and durability of brick masonry depends upon the quality of the brick, the quality of the mortar and the workmanship in laying. The strength also depends upon adequate bond and the shape of the masonry unit.
11 MIXING SHAFT BEARINGS The mixing shaft bearings are permanently factory sealed and lubricated, and should not require further service. DRUM SHAFT BEARING HANGERS Drum bearing hangers are located on each side of the drum, and are equipped with grease fittings.
12 8 – ADJUSTMENT RUBBER WIPER BLADES Adjust rubber wipers so they fit snugly against the drum but not to the point that they fold over when the blades rotate. ENGINE/MOTOR DRIVE SEE FIGURE 4. 1. Align pulleys correctly 2. Tighten locking collars in the direction of rotation and tighten setscrews.
13 9 – STORAGE For short term storage, clean the mixer and store in a dry place. If the mixer is not to be used for an extended period of time, service the mixer completely and store in a dry place. 1. Refer to the engine/motor instructions for storage instructions.
14.
15 Concrete Mixer Parts List REF NO. PART NO. DESCRIPTION QTY DRUM & DRIVE 1 232255 Bearing Hanger 2 2 1031 Grease Fitting 4 3 214837 Gear 1 4 5079 Drum Sheel Assembly 1 5 5207 Grill Assembly 1 6 .
16.
17 Concrete Mixer Parts List MIXING BLADES REF NO. PART NO. DESCRIPTION QTY 1 245711 Mixing Arm Assembly, Tow End 2 2 245709 Mixing Arm Assembly, Engine End 2 3 245705 MixingArm Cap 4 4 5235 Drum Wrap.
18.
19 Concrete Mixer Parts List ENGINE HOUSING AND AXLE REF NO. PART NO. DESCRIPTION QTY 1 245712 Engine Housing Assembly w/decals 1 2 245701 Housing Base Assembly 1 3 32082 Reflector 2 4 232623 T-Handle.
20.
21 Concrete Mixer Parts List FRAME, DRIVE AND CLUTCH CONTROL REF NO. PART NO. DESCRIPTION QTY 1 245265 Frame, Engine and Drive Support 1 2 245281 Frame Assembly 1 3 232276 Pin and Chain Assembly 1 4 *.
22.
23 Concrete Mixer Parts List ENGINE AND POWER OPTIONS REF NO. PART NO. DESCRIPTION QTY 1 232412 Belt Guide, Upper 1 2 245339 Belt Guide, Lower (Angled Bracket) 1 3 *70631 Nut, Hex 3/8-16 Cone Lock 3 4.
24.
25 Mixer Parts List ENGINE AND POWER OPTIONS MP600 Model 59299 REF. # PART # DESCRIPTION QUANTITY 14 245200 Engine, Honda GX240HA 8 HP 1 15 245400 Engine Mount Plate 1 16 239969 Belts (set of 2) 1 17 5254 Pulley, Drive 5 3/4 O.D. 1 18 5240 Pulley, Driven 8 1/4 O.
26 GILSON MIXER WARRANTY WARRANTY: This mixer is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from purchase date. Cleform Tool Corp. shall without charge, repair or replace parts which are found to be defective.
27 WARRANTIES ARE EXCLUDED AND DISCLAIMED AFTER THE EXPIRATION OF SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
An important point after buying a device Gilson 600MP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Gilson 600MP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Gilson 600MP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Gilson 600MP you will learn all the available features of the product, as well as information on its operation. The information that you get Gilson 600MP will certainly help you make a decision on the purchase.
If you already are a holder of Gilson 600MP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Gilson 600MP.
However, one of the most important roles played by the user manual is to help in solving problems with Gilson 600MP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Gilson 600MP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
