Instruction/ maintenance manual of the product FMC-16LX/FR Fujitsu
Go to page of 14
1 USER GUIDE PC Serial Programming Adapter Cable for Fujitsu Flash Microcontroller- F²MC-16LX/FR Family P/N: Fujitsu Microelectronics America, Inc..
2 Revision History Revision # Date Comment 1.0 03.25. 2001 New Docu men t 2.0 08.21.2003 Added devices in the Ta ble 3.0 04.11.2005 Added devices in the Ta ble and m odified th e layout of the document.
3 Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics America Inc, Sunnyvale restricts its warranties and its liability for the Product [MB904 55 seri e.
4 This document is intended to give an idea about in circuit serial programming of the Fujitsu F 2 MC16LX/FR family flash Microcontroller using an adapter cable. This method allows the user to program the microcontroller directly on the target system without additional RS232 circuit.
5 The diagram (figure1) below gives brief idea about all-n ecessary connections, which has to be done to program the on chip Flash memory. Target Board Adapter/Cable PC with Flash programming utility Figure 1- Interface Diagram Fujitsu standard Serial programming utility provides th e asynchronous method to program the microcontroller.
6 1 C1+ 3 C1- 4 C2+ 5 C2- 11 T1IN T1OUT 14 10 T2IN T2O UT 7 12 R1OUT R1IN 13 9 R2OUT R2IN 8 2 +V 6 -V 1 SIN 2 NC 3 MD0 4 GND 5 MD2 6 SOT 7 Pxx 8 Pyy 9 +Vcc 10 NC 1 CD 2 RD 3 TD 4 DTR 5 GND 6 DSR 7 RTS.
7 The following steps are required to set up the Hardwa re and software of the flash programming adapter. 1. Download the FLASH programming utility from the CD. 2. Connect one side of the ribbon cable to Adapter (J1) a nd other side to the user ta rget board (Note: The user board should have the 10-pin header for the cable).
8 In order to connect the adapter cable to the target board, it is required to have the 10-pin standard IDC header on the target board with the connection s hown below. Figure 3 shows the connections from the microcontroller to header. For detail pin out refer to Appendix A/B.
9 Pin No. Description Details 1 SIN/SI Connected to the SIN of the Microcontroller. Refer table-2 shown below. 2 NC 3 MD0 Connected to the MD0 pin of the MCU 4 GND Ground of the Target board and MCU 5 MD2 Connected to the MD2 pin of the MCU 6 SOT/SO Connected to the SOT of the Microcontroller.
10 Appendix A MCU Pins used for Flash as ynchronous Programming in F2MC Family.
11 Microcontroller pins used for Serial Programming.
12 Micr ocontr oll er pins use d for Ser ial Pr ogr amming.
13 Appendix B MCU Pins used for Flash as ynchronous Programming in FR Family.
14 Type Serial Data Input pin Serial data output pin Starting pin for programming program MB91F109 SI0/PF0/TRG0 SO0/PF1/TRG1 P20, P21 MB91F133 PI0/SIN1 P11/SOT1 P20, P21 MB91F233 P00/SIN0 PO 1/SOT0 P1.
An important point after buying a device Fujitsu FMC-16LX/FR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fujitsu FMC-16LX/FR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fujitsu FMC-16LX/FR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fujitsu FMC-16LX/FR you will learn all the available features of the product, as well as information on its operation. The information that you get Fujitsu FMC-16LX/FR will certainly help you make a decision on the purchase.
If you already are a holder of Fujitsu FMC-16LX/FR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fujitsu FMC-16LX/FR.
However, one of the most important roles played by the user manual is to help in solving problems with Fujitsu FMC-16LX/FR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fujitsu FMC-16LX/FR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
