

KTP-445U Head Unit Power Pack
ALPINE ELECTRONICS MARKETING, INC.
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
ALPINE ITALIA S.p.A. Viale C. Colombo 8, 20090 Trezzano Sui Naviglio (MI), Italy
1-1-8 Nishi Gotanda, Shinagawa-ku,
161-165 Princes Highway, Hallam Victoria 3803, Australia
Phone 02-484781 Tokyo 141-0031, Japan
ALPINE ELECTRONICS DE ESPANA, S.A.
ALPINE ELECTRONICS OF AMERICA, INC.
Wilhelm-Wagenfeld-Str. 1-3,
Portal de Gamarra 36,
19145 Gramercy Place, Torrance, California 90501, U.S.A. Phone 1-800-ALPINE-1 (1-800-257-4631)
80807 MOnchen, Germany Phone 089-32 42 640
Pabell6n,32 01013 Vitoria (Aiava)- APDO 133, Spain Phone 945-283588
ALPINE ELECTRONICS OF U.K. LTD.
ALPINE ELECTRONICS OF CANADA, INC.
Alpine House Fletchamstead Highway, Coventry CV4 9TW, U.K.
777 Supertest Road, Toronto, Ontario M3J 2M9, Canada Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS (BENELUX) GmbH
Phone 0870-33 33 763
1930 Zaventem, Belgium Phone 02-725-13 15
ALPINE ELECTRONICS FRANCE S.A.R.L.
98, Rue de Ia Belle Etoile, Z.l. Paris Nord II, B.P. 50016, 95945 Roissy Charles de Gaulle Cedex, France Phone 01-48638989


Introduction: Please read this OWNER·s MANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope that your new KTP-445U will give you many years of listening enjoyment. In case of problems when installing your KTP-445U, please contact your authorized ALPINE dealer. CAUTION: These controls are for tuning your system. Please consult your authorized Dealer for adjustment.
~WARNING This symbol means important instructions.
Failure to heed them can result in serious injury or death.
~CAUTION This symbol means important instructions.
Failure to heed them can result in injury or property damages.


+ IMPORTANT NOTICE This Amplifier has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules. This equipment generates and uses radio frequency energy, and it must be installed and used properly in accordance with the manufacturer•s instructions. + For European Customers Should you have any questions about warranty, please consult your store of purchase. + For Customers in other Countries
+IMPORTANT Please record the serial number of your unit in the space provided here and keep it as a permanent record. The serial number plate is located on the rear of the unit.


With this amplifier, there are two options for installation. Depending on which is best for your tarQet location, refer to .instructions A or B below.
~CAUTION + Caution on connection terminals/parts • Keep electrically conductive objects away from the unit's terminals/parts (power terminals, fuses, speaker output terminals, RCA connectors, etc.). Doing so prevents a possible short circuit and damage to the unit.
A. Installation with mounting brackets 1. Remove the two bottom screws on each end panel. 2. Use these screws to attach the included mounting brackets. 3. Using the amplifier as a template, mark the four screw locations. 4. Make sure there are no objects behind the surface that may become damaged during drilling. 5. Drill the screw holes. 6. Position the KTP-445U over the screw holes, and secure with four self-tapping screws. 7. Position the unit over the screw holes you prepared earlier. 8. Fasten the unit down with the four self-tapping screws (M4 x 12). Refer to Fig. 1.
B. Installation with chassis mounting loops 1. Push each of the included cable ties through the two mounting loops near each end on the bottom panel. 2. Use the cable ties to securely attach the amplifier to the vehicle's frame or chassis. Refer to Fig. 2.
Input Sensitivity · Crossover · Dimensions


(2) Ground Lead/
@ Hole/
Conducteur de mise a Ia terre/ Cable de tierra
Trous/ Agujeros/ @ Mounting Bracket/
Support/ Consola de montaje
CD Cable Tie/
(2) Ground Lead/
@ Mounting Loop/
Serre-cable/ Atadura de cables
Conducteur de mise a Ia terre/ Cable de tierra
Boucle de support/ Lazo del montaje


source connected. In such a case, connect the Remote Turn-On
Lead to an incoming power supply wire (accessory power) in the
8 Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on or power antenna
a. RCA Input Jacks (FRONT =Violet sleeve, REAR=Grey
Connect these jacks to the line out leads on your head
For the "Speaker Level Input System" setting. connecting the
SENSING" function of this product. However, the "REMOTE
unit using RCA extension cables (sold separately).
Remote Turn-On Lead is not required due to the "REMOTE
SENSING " function may no/ work depending on the signal
corresponding speaker outputs from the head unit
(positive trigger, (+) 12V only) lead of your head unit.
Cut off the RCA jacks, then connect the correct
directly to these twisted pair wires.
b. Speaker Level Inputs
4t Input Signal Wires There are two options:
ACC position.
amp directly to the positive(+) terminal of the vehicle's battery.
your audio components to the same point on the chassis to
Before making connections, be sure to turn the power off to all
audio components. Connect the yellow battery lead from the
To prevent external noise from entering the audio system.
15/16') away from the car harness. Keep the battery power leads as far away from other leads
vehicle's electrical system in case of a short circuit. Do
Be sure to add a 15A fuse (sold separately) as close as
0 Ground Lead (Black) Connect this lead securely to a clean , bare metal spot on
the vehicle's chassis. Verify this point to be a true ground
terminals/parts (power terminals, fuses, speaker output
Connect the ground lead securely to a bare metal spot
measures so consult your dealer for further information.
Do not connect speaker leads together or to chassis ground.
not connect the battery lead to the OEM radio circuit if
This is a pass through Remote Turn-On signal from the head
negative(-) terminal of the vehicle's battery. Ground all
terminals, RCA connectors, etc.). Doing so prevents a
Locate the unit and route the leads at least 10 em (3-
(remove any paint or grease if necessary) of the car
Your Alpine dealer knows best about noise prevention
Referring to "Cautions on speaker wire connections·;
by checking for continuity between that point and the
Failure to do so may result in fire or electric shock.
a. Connect battery lead to OEM radio fused circuit
The OEM radio circuit has a fuse to protect your
connect each speaker output wire to the correct
corresponding speaker wire on the vehicle side.
possible short circuit and damage to the unit.
8 Remote Out Lead {Blue/White) Use this lead to turn on additional amplifiers.
b. Connect battery lead directly to BATT+
Do not connect this lead to the fuse block.
possible to the battery's ( +) terminal.
the fuse rating is less than 15A.
8 Output/Power Wire Harness
REPLACING FUSES.
There are two options:
prevent ground loops.
as possible.
chassis.
unit.
I (Green/Biack)/(verl/nolr)/(Verde/negro) I e Posterior Izquierdo
(VIolel)/(vlolei)/(VIolela) 1 (!)~ Rear righV ~--~~~~~~~~~~::;:=;;;;::;::;=============:: Droitearri!re/ , (VIoleVBiack) (vlolel/nolr)/(VIolela/negro) , e Posterior derecha
:~~~~EI
ENTRADA
FRONTAL
REA~N / ARRI RE
ENTRADA
POSTERIOR
1 (Whlte)/(blanc)/(Bianco) 1 (!)~ Front lefV ~--~~~~~~~~;;,;;=:::;:;;::::;=============,1 GaucheavanV (Whlle/Biack)/(blanc/nolr)/(Bianco/negro) : e Frontal Izquierdo
,·(·G;e;n)t~;rt)t(v;rde)- ,, (!)~ RearlefV .
KTP-445U Left end panei/Le panneau de gauche/panel de Ia izquierda Fig. 3
KTP-445U Right end panel/panneau de droite/panel de Ia derecha Fig.4
REMOTE TURN-ON/ACTIVATION DE LA TELECOMMANDE/ENCENDIDO REMOlD •
'R"E'MiiiE riiR"N:o"NiAcr~v~iloN-o~ ~ r~~EcoririA;o-EiE;r:E;O",iioREMiiro- -ii-
D· •


installed in-line on the KTP-445U turn-on lead. This switch will
then be used to turn on (and off) the KTP-445U. Therefore, the
switch should be mounted so that is accessible by the driver.
running. Otherwise, the amplifier will remain on and drain the
If this is objectionable, a SPST (Single Pole, Single Throw)
switch, in addition to the 3A fuse mentioned above, may be
Make sure the switch is turned off when the vehicle is not
® To other Alpine components' Remote Turn-On Leads
(/) As close as possible to the vehicle's ignition tap
@ r=usa(3A)
@ SPST Switch (optional)
@ Remote Turn-On Lead
battery.
until the output distorts. Then, reduce the volume 1 step (or
distorted. Reduce the gain slightly so the sound is no longer
cutoff frequency to 60Hz on front or rear
cutoff frequency to 80Hz on front or rear
Input Configuration Switch should be in the up position for 2 CH
a dynamic CD as a source, increase the head unit volume
b. The head unit's power antenna lead is activated only when
(+) 5V, negative trigger (grounding type), or cannot sustain
(+) 12V when connected to other equipment in addition to
the vehicle's power antenna. If any of the above conditions
445U will turn on and stay on as long as the ignition switch is on.
position to turn off HP filter on front or
b) Slide switch 1 to the down position and
switch 2 to the down position to set the
a) Slide switch to the down position for 4
a) Slide switch to the up position for RCA
until the output is no longer distorted). Now, increase the
amplifier gain until the sound from the speakers become
a. The head unit does not have a remote turn-on or power
c. The head unit's power antenna lead is logic level output
exist, the remote turn-on lead of your KTP-445U must be
vehicle. Be sure to use a 3A fuse as close as possible to
this ignition tap. Using this connection method, the KTP-
switch 2 to the up position to set the
c) Slide switch 1 to the up position and
position to set the cutoff frequency to
b) Slide switch to the down position for
Please check your head unit for the conditions listed
connected to a switched power source (ignition) in the
d) Slide switches 1 and 2 to the down
b) Slide switch to the up position for 2
a) Slide switches 1 and 2 to the up
rear channels [DEFAULT setting]
120Hz on front or rear channels
channel input [DEFAULT setting]
input signals [DEFAULT setting]
the radio is on (turns off in the tape or CD Mode).
distorted to achieve the optimum gain setting.
speaker level input signals
channels.
bridged output system.
antenna lead.
~ .
RCA
SPKR
12 OFF
5 4CH
Fig.S
KTP-445U Bottom panel/panneau inferieur/Panel inferior
KTP-445U Right end paneVpanneau de droite/panel de Ia derecha
I ·~~P~'r or:::::JD
r ~
lWJ l ~ l
, ______ _
~~ r
1 FR ON T 1 1 GAIN 1 h0l
®
When using speaker level inputs, both
du gain avant et arriere doivent etre
ambos controles de ganancia deberim
/ograr una gama de volumen tipica del
Les carres noirs indiquent les
front and rear gain controls should
be between minimum and 9 o'clock
position for typical head unit volume
parleur sont uti/isees, /es con troles
entre les positions minimales et 9
heures pour Ia gamme de volume
AI usar entradas a nivel de bocina,
Los cuadros negros indican
Si des entrees du niveau de haut-
estar entre una posiciOn minima y
Ia posicion de las 9 en punto para
Black squares indicate the
positions of the switches.
typique de /'unite principale.
positions des se/ecteurs.
las posiciones de los
amplificador principal.
interrupt ores.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.