

CDA-7846E
FM/AM Compact Disc Receiver

DX SEEK DN 7 DN 1 UP 8 UP 2 M.I.X. 9 D.A.P. 3

English Precautions This label is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions will result severe injury or death. Warning
DO NOT DISASSEMBLE OR ALTER. Doing so may lead to accident, fire or electric shock.
KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN. If swallowed, consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. When problems occur such as a lack of sound or video, foreign objects inside the unit, smoke coming out, or noxious odors, stop use immediately and contact the dealer where you bought the equipment. Failure to do so may result in an accident or injury.
DO NOT OPERATE THE EQUIPMENT OR LOOK AT THE SCREEN WHILE DRIV- ING THE VEHICLE. Operating the equipment may distract the driver from looking ahead of the vehicle and cause accident. Always stop the vehicle in a safe location before operating this equipment.
DO NOT RAISE THE VOLUME EXCESSIVELY. Keep the volume at a level where you can still hear outside noises while driving. Driving while unable to hear outside noises could be the cause of accident.
DO NOT USE THIS EQUIPMENT FOR PURPOSES OTHER THAN STATED FOR THE VEHICLE. Failure to do so may result in electric shock or injury.
DO NOT PLACE FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS. Do not insert hands, fingers or foreign objects in the disc or cassette insertion slots, or in gaps during monitor startup/storage. Doing so may result in personal injury or damage to the equipment.
This label is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions can result injury or material damage.
DO NOT BLOCK VENTS OR RADIATOR PANELS. Blocking them may cause heat to build up inside and may result in fire.
STOP THE VEHICLE IF UNIT OPERATION MIGHT INTERFERE WITH DRIVING.

Basic Operation 8 Initial System Start-up 9 Turning Power On and Off 9 Turning Loudness On/Off 10 Subwoofer On and Off 11 Non Fading Pre-Out (N.F.P.) On and Off 12 Adjusting Volume/Bass/Treble/Balance/Fader 13 Audio Mute Function 13 Sound (Beep) Guide Function 14 Adjusting Display Contrast 15 Turning Mute Mode On/Off 16 Demonstration 17 Displaying Time 18 Setting Time 19 Using the Function Button
Radio Operation 20 Manual Tuning 21 Automatic Seek Tuning 22 Manual Storing of Station Presets 23 Automatic Memory of Station Presets 24 Storing into Direct Access Preset (D.A.P.) Band 25 Tuning to Preset Stations 26 Displaying Station Titles 27 Titling Stations 29 Displaying Station Signal Strength [T.RCL (Tuner Recall)] 29 Mono/Stereo Switching
CD Operation 30 Inserting Disc 31 Removing Disc 32 Normal Play and Pause 33 Music Sensor (Skip) 34 Fast Forward and Backward 34 Repeat Play 35 M.I.X. (Random Play) 36 Scanning Programs 37 To Display CD Titles 38 Titling Disc 40 Erasing Disc Title
CD Shuttle Operation 41 Controlling CD Shuttle (Optional) 43 Searching Titled Discs (Title Search Menu) 44 Multi-Changer Selection
46 Remote Control 49 Disc Care 50 In Case of Difficulty 54 Specifications

Thermal Be sure the temperature inside the vehicle is between +60°C (+140°F) and –10°C (+14°F) before turning your unit on.
Moisture Condensation You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
Damaged Disc Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.
Never Attempt the Following Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.
Maintenance If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
Irregular Shaped Discs Make sure the discs you use in this unit do not have any irregularities. The outer and inner edges should be round and smooth. Use of irregularly shaped discs may cause damage to the mechanism.
English

Inserting Discs Your player accepts only one disc at a time for playback. Do not attempt to load more than one disc. Make sure the label side is facing up when you insert the disc. Your player will automatically eject any disc that is inserted incorrectly. If the player continues to eject a correctly inserted disc, push the Reset switch (located behind the detachable front panel) with a pointed object such as a ball-point pen. Playing a disc while driving on a very bumpy road may result in skips, but this will not scratch the disc or damage the player.
New Discs As a protective measure, the CD player will automatically eject discs that have either been inserted incorrectly or have irregular surfaces. If a new disc is ejected immediately after loading, use your finger to feel around the outer edge of the CD and its center hole. If you feel any small bumps or irregularities, this could inhibit proper loading of the disc. To remove the bumps, rub the inside edge of the hole and outside edge of the disc with a ball-point pen or other such instrument, then insert the disc again.
Bumps
Center Hole New Disc
Outside (Bumps)
English




Press the PWR (Power) button to turn off the power.
Press the RLS (release) button until the front panel pops out.
Grasp the left side of the front panel and pull it out.
Attaching the Front Panel 1. First, insert the right side of the front panel into the main unit. Align the 2 small holes on the front panel with the 2 projections on the main unit. 2. Push the left side of the front panel until it locks firmly into the main unit.
sure that there is no dirt or dust on the connector terminals and no foreign objects between the front panel and main unit.
English · English

Initial System Start-Up
1 When operating the unit for the first time after installation or after the vehicle's battery has been disconnected and reconnected, set the volume level to its minimum, then remove the detachable front panel. (Refer to page 7.)
Press the button with a ball-point pen or any other pointed object. The plate opens automatically.
There is a small hole at the lower right side. Behind this hole the red Reset switch is located. Press the Reset switch with a ball-point pen or any other pointed object.
Push the plate to close it until a click sound is produced.
Attach the front panel (see page 7).

Press the PWR button to turn off the unit.
The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press the PWR button again to turn off the unit.
Turning Loudness On/Off Loudness introduces a special low- and high- frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.
Press and hold the LOUD button for at least 2 seconds to activate or deactivate the loudness mode.
LOUD
The display shows "LOUD" when the loudness mode is activated.
the CDA-7846E, not all functions or display indications will operate as described. For details, consult your Alpine dealer.

Subwoofer On and Off Change the setting when an optional product having the Subwoofer output terminals is Ai- NET connected.
Press and hold the PWR button for at least 3 seconds.
Press the F1 button repeatedly to select "SUBW.". With each press, subwoofer is toggled ON or OFF.
When the subwoofer is ON: Press the MODE button for at least 2 seconds repeatedly, and the subwoofer output phase is toggled 0° or 180°.
Press the PWR button, after setting the subwoofer ON.
4 MODE LOUD
Press the MODE button repeatedly to select the subwoofer mode.
BALANCE
FADER
5 SW 15
Press the or button to adjust the subwoofer output level. The setting is displayed for 5 seconds and then memorized.
Subwoofer

Non Fading Pre-Out (N.F.P.) On and Off
Press and hold the PWR button for at least 2 seconds.
2 N.F.P. ON
Press the F1 button. With each press, N.F.P. is toggled On or Off.
Output will not be affected by the fader. This is ideal for driving a subwoofer amplifier. N.F.P. OFF:Returns to normal fader mode.
subwoofer is used.
Press the PWR button to set the selected mode.

Press the MODE/LOUD button repeatedly to choose the desired mode.
BASS
TREBLE
BALANCE
FADER
Press the button or until the desired sound is obtained in each mode.
each source (FM, AM and CD) are automatically memorized. These settings remain until you manually change them.

Audio Mute Function Activating this function will instantly lower the volume level by 20 dB.
Press the F6 button to activate the MUTE mode. The volume bar graphic indicator will flash in the display and the audio level will decrease by about 20 dB. Pressing the F6 button again will bring the audio back to its previous level and the display will return to normal.
F6 MUTE
(ON)
F6 (OFF)
MUTE
In the CD mode, press the F6 button when the FUNC indicator is off.
Sound (Beep) Guide Func- tion This function will give audible feedback with varying tones depending upon the button pressed.
Press and hold the PWR button for more than 2 seconds.
With each press of the F2 button, BEEP is toggled ON or OFF.
PWR INTLZ
Press the PWR button to set the selected mode.

Adjusting Display Contrast You can adjust the display contrast for better visibility.
Press and hold the PWR button for at least 2 seconds.
Press the F3 button. The "CONTRAST" is displayed.
Press the c or f button to adjust the contrast of the display. You can adjust in a range of –6 and +6. The initial setting at the factory is "0".
DN UP
PWR INTLZ
Press the PWR button to set the selected mode.

Turning Mute Mode On/Off With a cellular phone or navigation system connected, audio will be interrupted whenever a call is received. This function can be manually turned ON or OFF from the head unit by following procedure below.
Press and hold the PWR button for at least 2 seconds.
With each press of the F4 button, the MUTE is toggled ON or OFF.
MUTE OFF
Press the PWR button again to return to normal operation.

Demonstration In the Demonstration (DEMO) mode, the unit scans each function of the sources; Tuner, CD player and CD shuttle if an optional CD Shuttle is connected.
Press the DEMO button to activate the DEMO mode. The DEMO mode is activated and the unit automatically performs the operation.
To end the DEMO mode, press the DEMO button.

Displaying Time
Press the CLK (CLOCK) button to display the time. The unit displays the time.
12:00
TITLE
in the Clock mode will interrupt the time display momentarily. The function selected will be displayed for about 5 seconds before the time returns to the display.
Press the CLK (CLOCK) button to turn off the time and to show other functions.

Setting Time
Press the CLK (CLOCK) button to display the time.
TITLE
12:00
power.
Press and hold the CLK (CLOCK) button for at least 2 seconds. The time indication will begin to blink.
12:30
TITLE
Press the F4 button while the time indication is blinking to set seconds to "0".
12:00
Press the F5 button to adjust the hours while the time indication is blinking.
5 F6
Press the F6 button to adjust the minutes while the time indication is blinking. The time indication will stop blinking 5 seconds after the last adjustment. The time will automatically be set.
9:35

Using the Function Button The chart below describes the function of each preset button. The function will change depending upon the source selected and the condition of the FUNCTION switch, ON or OFF.
Press the FUNC (FUNCTION) button. The function mode will change each time you press the button. (Refer to the chart below.)
Press any one of the F1 – F6 buttons.
Function indicator
F1 F2 F3 F4 F5 F6
Mode
(on/ off)
Preset 2 Preset 3 Preset 4 Preset 5 Preset 6
D.A.P. (Direct Access Memory Preset)
MONO (Stereo/Monaural) T.RCL (Tuner Recall)
FUNC
M.I.X. (Randam Play) RPT (Repeat) SCAN MUTE
Disc Select 1 Disc Select 2 Disc Select 3 Disc Select 4 Disc Select 5 Disc Select 6
M.I.X. (Randam Play) RPT (Repeat) SCAN MUTE
Disc Select 1 Disc Select 2 Disc Select 3 Disc Select 4 Disc Select 5 Disc Select 6
Disc Select 7 Disc Select 8 Disc Select 9 Disc Select 10 Disc Select 11Disc Select 12
D–DN (Disc DOWN) D–UP (Disc UP) M.I.X. (Randam Play) RPT (Repeat) SCAN MUTE
Clock Adjust-
(HOUR)
ment
(CT)
(MIN)

Manual Tuning
Press the SOURCE button to select the radio mode.
Press the BAND button repeatedly until the desired radio band is displayed.
BAND T.S.M.
FM2
AM
3 SEEK
Press the TUNE button repeatedly until "MANUAL" appears in the display.
TUNE A. ME
MANUAL
Press the (c) DN or UP (f) button to move downward or upward one step respectively until the desired station frequency is displayed.
DN UP
when a Stereo FM station is tuned in. If the stereo FM signal becomes weak, the "ST" indicator disappears and the unit automatically switches the mode from stereo to monaural to reduce the noise. When the signal becomes strong enough, the unit automatically switches back to the stereo mode.

English Radio Operation
Automatic Seek Tuning
Press the SOURCE button to select the radio mode.
Press the BAND button repeatedly until the desired radio band is displayed.
BAND T.S.M.
AM
Press the TUNE button to illuminate the DX and SEEK indicators in the display. With the DX mode activated, both strong and weak stations will be tuned automatically. Press again to return to the local mode. The DX indicator will turn off and only the SEEK indicator will remain illuminated. Now only strong stations will be tuned.
DX
SEEK
LOCAL SEEK
MANUAL
Press the (c) DN or UP (f) button to automatically seek a station downward or upward respectively. The unit will stop at the next station it finds. Press the same button again to seek next station.
DN UP

Manual Storing of Station Presets
1. Tune in the desired radio station you wish to store in the preset memory. 2. Check that the "FUNC" indicator is off. 3. Press and hold any one of the preset buttons (1 through 6) for at least 2 seconds. The frequency display will begin to blink. 4. Press the preset button into which you wish to store the station while the display is blinking (within 5 seconds). The display stops blinking to indicate that the station has been memorized. The preset number is also displayed. 5. Repeat the procedure to store 5 other stations onto the same band. Use this procedure for other bands.
A total of 24 stations can be stored in the preset memory (6 stations for each band; FM1, FM2, AM and D.A.P.).
in the same preset location, it will be cleared and the new station will be memorized.

English Radio Operation
Automatic Memory of Station Presets
Press the SOURCE button to select the radio mode.
Press the BAND button repeatedly until the desired radio band is displayed.
BAND T.S.M.
AM
Press and hold the A. ME button for at least 2 seconds. The frequency on the display continues to change while the automatic memory is in progress. The tuner will automatically seek and store 6 strong stations in the selected band in order of signal strength. When the automatic memory has been completed, the tuner goes to the station stored in the preset location F1.
return to the original station you were listening to before the auto memory procedure began.

Storing into Direct Access Preset (D.A.P.) Band A combination of radio stations in any band, AM and FM (up to 6 stations) can be manually preset onto the D.A.P. band.
Press the F3 button when the "FUNC" indicator is on.
F3 F3 D.A.P.
Press the BAND button to select FM or AM. The selected band will be displayed. To memorize stations onto the D.A.P. band, follow the steps for the automatic or Manual Storing of Station Presets section above.
F3 D.A.P.
with D.A.P., 4 FM and 2 AM stations will be stored in Presets 1 – 4 and 5 – 6 respectively.
To cancel the D.A.P. mode, press the F3 button. The red line above the D.A.P. indicator will turn off.

English Radio Operation
Tuning to Preset Stations
Press the SOURCE button to select the radio mode.
Press the BAND button repeatedly until the desired band is displayed.
BAND T.S.M.
AM
To select the D.A.P. band, press the F3 button with the "FUNC" indicator on.
F3 D.A.P.
Press the station preset button that has your desired radio station in memory. The display shows the band, preset number with a triangle and frequency of the station selected.
pressing the F1 or F2 button can select the stations.


If a title has been entered for the selected station, it can be displayed in place of the frequency. The display will toggle between the frequency and title display with each press of the TITLE button. (Refer to page 27 to title stations.)

CLOCK PRIORITY Mode
STATION TITLE Mode
Title not entered Title entered
Characters and Symbols

A (a) B (b) C (c) D (d) E (e) F (f) G (g) H (h) I (i)
K (k) L (l) M (m) N (n) O (o) P (p) Q (q) R (r) S (s)
U (u) V (v) W (w) X (x) Y (y) Z (z) 0 1 2
4 5 6 7 8 9 ! " #
Blank



Change to the TITLE mode. Press and hold the TITLE button for at least 2 seconds. The first digit will blink.
Press FUNC button to select the desired mode. It will change each time you press the button. Refer to “Character and Symbols” on page 26.

Press the c DN or UP f button to select the desired letter/numeral/symbol available for naming ("A" for example).
If entering a letter (alphabet), press the F1 button to change to lowercase. Press the F2 button to return to all caps mode.
a


Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title.
Repeat the steps – above to complete the titling. All 10 character positions should be filled. Use spaces where characters are not needed (for example at the end of a 5 character title, use 5 spaces to complete the title).
After the last character has been entered (character number 10), the title will automati- cally be stored.

English Radio Operation
Displaying Station Signal Strength [T.RCL (Tuner Re- call)] You can display the signal strength of a desired radio station while you are listening to other sources such as CD player or CD Shuttle.
When the "FUNC" indicator is on, press the F5 button in the Tuner mode. The display shows the bar-graphic signal strength of the selected radio station. To cancel the T.RCL mode, press the F5 button again.
F5 T.RCL
(ON)
F5 T.RCL
(OFF)
antenna during the T.RCL mode.
"ST" indicator appears when a stereo is tuned in.
(OFF)
F4
When the "FUNC" indicator is on, press the F4 button to switch from stereo to monaural FM reception. This will help in reducing the noise of weak FM Stereo broadcasts. In the monaural mode, the "ST" indicator disappears. Press the F4 button again to return to the stereo mode.
(ON)


Press the OPEN button to open the front door. The CD compartment is located behind the front door.
Insert a CD half way into the slot with the label side facing up. The player automatically draws the disc into the disc compartment. When the CD is loaded, the player automatically starts CD playback and DISC-IN indicator lights up.
Close the front door with your hand until you hear a click sound.


Press the OPEN button to open the front door.
Press the Eject (h) button on the top side of the front door. The CD is automatically ejected half way out. Remove the CD with your hand.
seconds, the player automatically draws the CD into the compartment to protect the CD.
Close the front door with your hand until you hear a click sound.


Insert a CD into the CD player. The CD player begins playback from the first track on the disc. The display shows the track number and elasped time of the track being played. When the last track is played back the player returns to the first track and begins playback from that point.

If a CD is already loaded in the CD player, press the SOURCE button to select the CD mode.
Press the k (Play/Pause) button during the play mode to place the player in the Pause mode. "PAUSE" appears in the display. To resume playback, press the k button again.


Momentarily press the (c) DN button once to return to the beginning of the current track. If you wish to access a track further back, repeatedly press until you reach the desired track. (The example shows the Music Sensor operation starting from track No. 4.)
Press the UP (f) button once to advance to the beginning of the next track. If you wish to access a track further ahead, press repeatedly until the desired track is reached.


Press and hold the (c) DN or UP (f) button to quickly move backward or forward until you reach the desired section of the track.

Press the F4 button to play back repeatedly the track being played. The RPT indicator appears and the track will be played repeatedly.
Press the F4 button again to deactivate the repeat play.
F4 RPT
F4 RPT
(1 track repeat) · (*All tracks repeat)

M.I.X. (Random Play)
1 F3 M.I.X.
Press the F3 button in the play or pause mode. The M.I.X. indicator will illuminate and the tracks on the disc will be played back in a random sequence. After all the tracks on the disc have been played back once, the player will begin a new random sequence play until the M.I.X. mode is canceled.
F3 M.I.X.
To cancel M.I.X. play, press the F3 button again.
ALL function is connected, "
F3 ALL RPT " will be displayed.


Press the F5 button to activate the Scan mode. The first 10 seconds of each track will be played back in succession.
To stop the Scan, press the F5 button to deactivate the Scan mode.


After a title has been entered for a CD, it can be displayed by pressing the TITLE button. The display will toggle between Normal, Clock and CD Title with each press of the TITLE button (see example below). (Refer to page 38 to title the disc.)
A (a) B (b) C (c) D (d) E (e) F (f) G (g) H (h) I (i)
K (k) L (l) M (m) N (n) O (o) P (p) Q (q) R (r) S (s)
U (u) V (v) W (w) X (x) Y (y) Z (z) 0 1 2
4 5 6 7 8 9 ! " #
% & ’ ( ) * + , -


Select a disc for which you want to enter a title.

Change to the TITLE mode. Press and hold the TITLE button for at least 2 seconds. The first digit will blink.

Press the FUNC button to select the desired mode. The mode will change each time you press the button. Refer to “Characters and Symbols” on page 37.
Press the c DN or UP f button to select the desired letter/numeral/symbol available for naming ("A" for example).

If entering a letter (alphabet), press the F1 button to change to lower case. Press the F2 button to return to all caps mode.

Titling Disc (Continued)
Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title. Repeat the steps – above to complete the titling. Pressing the TITLE button after entering the 12th character, automatically stores the title into memory.
TITLE
AL
In case of storing a title of less than 12 characters: For example, after 3rd digit character is completed, 4th digit character is blinking. Then, go to step .
TITLE



Press the TITLE button to select the disc titling mode. Then, press and hold for at least 2 seconds.
Press and hold the FUNC button for at least 2 seconds to activate the title scanning mode. The title in the display will blink, for example "ALPINE".

Press the (c) DN or UP (f) button repeatedly until the disc title you want to erase is dis- played.

Press and hold the FUNC button for at least 2 seconds to erase the disc title displayed.

Press and hold the TITLE button for at least 2 seconds to cancel the disc title erasing mode.

Controlling CD Shuttle (Optional) An optional 6-disc or 12-disc CD Shuttle may be connected to the CDA-7846E if it is Ai-NET compatible. With a CD Shuttle connected to the Ai-NET input of the CDA-7846E, the CD Shuttle will be controllable from CDA-7846E. Using the KCA-400C (the Multi-Changer Switching device) multiple changers can be controlled by the CDA-7846E. See the Multi-Changer Selection section on page 44 for selecting the CD Shuttles.
Press the SOURCE button to activate the CHANGER mode. The display shows the “Changer” disc number and track number.
SOURCE
CD
Press the FUNC button to select the FUNC OFF1 or OFF2 mode.
FUNC OFF1 mode:
In this mode you can select the discs between 1 and 6.
FUNC OFF2 mode (for 12-disc CD Shuttle only):
In this mode you can select the discs between 7 and 12.
FUNC
(FUNC ON mode)

Controlling CD Shuttle (Optional) (Continued)
Press the Function button (F1 through F6) corresponding to one of the discs loaded in the CD Shuttle. The selected disc number appears in the display and CD playback starts.
For FUNC OFF1 mode
For FUNC OFF2 mode
7 8 9 10 11 12 1 2 3 4 5 6
F2 F3 F4 F5 F6
operate in the same way as for the CDA- 7846E CD player. For details, please see the CD Operation section.

Searching Titled Discs (Title Search Menu)
Press the TITLE button to activate the Title Display mode.
TITLE
Press and hold the T.S.M. button for at least 2 seconds while the title is displayed. The title in memory blinks in the display.
BAND T.S.M.
Press the (c) DN or UP (f) button to select the desired disc title.
Press the T.S.M. button to play the selected disc. The unit will automatically search the disc and will play that disc.
BAND T.S.M.

Multi-Changer Selection Alpine’s Ai-NET system will support up to 6 CD Shuttles. When operating two or more changers, the KCA-400C (Multi-Changer Switching device) must be used. If you use 1 Switching device, you can connect up to 4 CD Shuttles. If you use 2 Switching devices, you can connect up to 6 CD Shuttles.
BAND PROG SOURCE A.PROC
Remote Control
Press the SOURCE button on the CDA-7846E to activate the CD Changer mode.
Alternatively, press the SOURCE button on the Remote Controller (RUE-4185) to activate the CD Shuttle mode. Proceed to Step below to select the desired CD Shuttle.
Press the BAND button on the CDA-7846E or the RUE-4185 to activate the CD Shuttle Selection mode.
BAND T.S.M.
The CD Shuttle Selection mode remains active for 3 seconds after Step is performed. Press the BAND button until the desired CD Shuttle indicator appears on the display.
BAND T.S.M. Changer-X
nected, the display will show "No Changer X".

Multi-Changer Selection (Continued)
BAND PROG SOURCE A.PROC
Remote Control
3 Press the BAND button on the Remote Controller until the desired changer indicator appears on the display.
To operate the selected changer, see "CD Operation" section.

Controls
1 Mute Button Press the button to lower the volume by 20 dB instantly. Press the button again to cancel.
MUTE
2 Power Switch Press the switch to turn the power on/off.
ENT
3 k Button Press the button to switch between the Play and Pause modes for the CD.
BAND PROG SOURCE A.PROC
4 CD Changer Button Press the button to change to the CD Shuttle operation.
5 Band/Program Button Radio mode: BAND Button Press the button and the band will change as shown below.
6 Volume Adjustment Buttons To increase the volume level Press the button To decrease the volume level Press the button
7 Button Radio mode: Pressing the button will select, in ascending order, stations programmed into the radio's presets as shown below.
CD/CD Shuttle mode: DISC Select (UP) Button Press the button to select a disc in ascending order.

8 Button Radio mode: SEEK (DN) Button CD/CD Shuttle mode: Press the button to go back to the beginning of the current track.
9 Button Radio mode: SEEK (UP) Button CD/CD Shuttle mode: Press the button to advance to the beginning of the next track.
PWR
ENT
CD-CHG
Radio mode: Pressing the button will select, in descending order, stations programmed into the radio's presets as shown below.
REMOTE CONTROL UNIT
CD/CD Shuttle mode: DISC Select (DN) Button Press the button to select a disc in descending order.
Å Audio Processor Button**
Press the button to call the external audio processor mode.*
Ç Audio Select Button
Press to select the audio source.
* For the operation of external audio processor, refer to the Owner's Manual of the external audio processor you pur- chased. ** This button is used in conjunction with an optional Ai-NET processor.
Ä Button

Battery Replacement Applicable battery: Use two "AAA" sized dry batteries or equivalent.
Opening the battery cover Slide out the battery cover while firmly pressing outward.
Replacing the battery Put the batteries in the case as illustrated.
d
e
Closing the cover Push the cover as illustrated until a click is heard.
e

Correct Handling Do not drop the disc while handling. Hold the disc so you will not leave fingerprints on the surface. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.
INCORRECT CORRECT
Disc Cleaning Fingerprints, dust, or soil on the surface of the disc could cause the CD player to skip. For routine cleaning, wipe the playing surface with a clean, soft cloth from the centre of the disc to the outer edge. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent before cleaning the disc.
Disc Accessories There are various accessories available on the market for protecting the disc surface and improving sound quality. However, most of them will influence the thickness and/or diameter of the disc. Using such accessories can cause the disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players.
Disc Stabilizer
English

If you encounter a problem, please review the items in the following check list. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.
No function or display.
English · Symptom · Cause and Solution

Radio Mode
Unable to receive stations.
Unable to tune stations in the seek mode.
Broadcast is noisy.
Symptom · Cause and Solution

CD Mode
CD insertion not possible.
Unable to Fast-Forward or Backward.
Sound skips due to vibration.
Sound skips without vibration.
English · Symptom · Cause and Solution

Indication for CD Shuttle
Indication Cause and Solution
Hi Temp.
English

Tuning Range 87.5 – 108.0 MHz
Mono Usable Sensitivity 9.3 dBf (0.8µV/75 ohms)
50 dB Quieting Sensitivity 13.5 dBf (1.3µV/75 ohms)
Alternate Channel Selectivity 80 dB
Signal-to-Noise Ratio 65 dB
Stereo Separation 35 dB
Tuning Range 531 – 1,602 kHz
Usable Sensitivity 22.5µV/27.0 dB
Frequency Response* 5 – 20,000 Hz (±1 dB)
Wow & Flutter (% WRMS)* Below measurable limits
Total Harmonic Distortion* 0.008% (at 1 kHz)
Dynamic Range* 95 dB (at 1 kHz)
Signal-to-Noise Ratio* 95 dB
Channel Separation* 85 dB (at 1 kHz)
Battery Type "AAA" sized dry battry
Battery Quantity 2
Dimensions (W x H x D) 56mm (2-1/4") x 14mm (9/16") x 105mm (4-1/8")
Weight (without battery) 50 g (1 oz)

Power Requirement 14.4V DC (11 – 16V (allowable))
Maximum Power Output 40W x 4
Pre-Output Voltage 2000 mV/10k ohms
Bass ±15 dB at 30 Hz
Treble ±10 dB at 10 kHz
Weight 1.5 kg (3 lbs. 5 oz)
Width 178mm (7")
Height 50mm (2")
Depth 150mm (5-7/8")
Width 170mm (6-3/4")
Height 46mm (1-13/16")
Depth 22mm (7/8")
* Measured at internal amp input stage.
tions and design are subject to change without notice.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.