Instruction/ maintenance manual of the product 500 XT Flymo
Go to page of 9
For all customer enquiries or for replacement parts, contact:- 01325 300303 www .flymo.com customer .services@husqvarna.co.uk Original Instructions IMPOR T ANT INFORMA TION Read before use & r.
Carton Contents IMPORT ANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY P ARTS ARE MISSING CONT ACT :- Husqvarna UK Ltd. Customer Service Department direct T elephone : 01325 300303 Fax : 01325 302530 Safety General 1 .
7. Do not pull cable around sharp objects. 8. Always switch off at the mains before disconnecting any plug, cable connector or extension cable. 9. Never pull on the cable to disconnect any of the plugs. 1 0 . Switch off, remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage.
Wheel Assembly (B1) & (B2) 1. Fix the 2 halves of the wheel together as illustrated in fig B1 . 2. Attach the wheel to the trimmer making sure that it is located into the groove on the trimmer head (B2) . 3. Clip the wheel together on the other side, making sure it is secure.
• WARNING • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer . Overloading can be avoided by making sure the motor speed does not drop unduly .
T o manually feed the nylon line (Q) 1. If required line can be fed out manually . 2. T o operate, press and release manual line feed button, whilst gently pulling on one of the lines until the line reaches the line cutter .
Y X Maintenance W V • WARNING Disconnect from the mains electricity supply , be- fore attempting any maintenance or adjustment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard.
Fault Finding Chart WARNING Disconnect from the mains electricity supply befor e attempting any maintenance or adjustment. F AUL T CHECK ACTION Is the automatic line feed work- ing? Manually feed out line.
5101570-01 Husqvarna UK Ltd. Aycliffe Industrial Park NEWTON A YCLIFFE Co.Durham DL5 6UP ENGLAND T elephone - (00) 44 1325 302302 Fax - (00) 44 1325 310339 Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
An important point after buying a device Flymo 500 XT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Flymo 500 XT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Flymo 500 XT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Flymo 500 XT you will learn all the available features of the product, as well as information on its operation. The information that you get Flymo 500 XT will certainly help you make a decision on the purchase.
If you already are a holder of Flymo 500 XT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Flymo 500 XT.
However, one of the most important roles played by the user manual is to help in solving problems with Flymo 500 XT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Flymo 500 XT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
